SP5500+ /SP6000+ /

SP7000+
Programming Guide
4 to 32-Zone Expandable Security Systems
Warranty
For complete warranty information on this product please refer to the Limited Warranty Statement found on our Web site: www.paradox.com. Your use of this Paradox product signifies
your acceptance of all warranty terms and conditions.

Limitations of Alarm Systems

It must be understood that while your Paradox alarm system is highly advanced and secure, it does not offer any guaranteed protection against burglary, fire or other emergency (fire and
emergency options are only available on certain Paradox models). This is due to a number of reasons, including by not limited to inadequate or improper installation/positioning, sensor
limitations, battery performance, wireless signal interruption, inadequate maintenance or the potential for the system or telephone lines to be compromised or circumvented. As a result,
Paradox does not represent that the alarm system will prevent personal injury or property damage, or in all cases provide adequate warning or protection.

Your security system should therefore be considered as one of many tools available to reduce risk and/or damage of burglary, fire or other emergencies, such other tools include but are not
limited to insurance coverage, fire prevention and extinguish devices, and sprinkler systems.
We also strongly recommend that you regularly maintain your security systems and stay aware of new and improved Paradox products and developments.
TBR-21: In order to comply with TBR-21, standard force dialing must be enabled.

© 2022 Paradox Security Systems (Bahamas) Ltd. All rights reserved. Specifications may change without prior notice. One or more of the following US patents may apply: 7046142, 6215399,
6111256, 6104319, 5920259, 5886632, 5721542, 5287111, 5119069, 5077549 and RE39406. Canadian and international patents may also apply. Magellan, Spectra SP and BabyWare are
trademarks or registered trademarks of Paradox Ltd. or its affiliates in Canada, the United States and/or other countries.
Things You Need to Know
About this Programming Guide
Use this programming guide to record programmed settings for your SP+ Series control panel. This guide should be used along
with the SP+ Series Reference & Installation Manual (available online), whenever installing or programming your SP+ system.
Conventions
The following typographical conventions are used throughout this guide:
Default Settings: Values which appear in bold typeface signify the default value: e.g., : Installer Quick Menu (indicates that information on the topic can
Access code length:  6 digits  4 digits (4 digits is the default value) also be found in the Installer Quick Menu on page 7)
Section numbers and keypad keys also appear in bold typeface, enclosed by NOTE: Suggestion, important information, or reminder
brackets: e.g., Section [706] must be enabled...

Installer Code
The default installer code is 0000. This code allows you to enter programming mode, where you can program all features, options,
and commands of the control panel, except for user codes. To change this code, see System Codes on page 27.
Maintenance Code
Similar to the installer code, the maintenance code allows you to enter programming mode and program all sections, except for
user codes and communication settings (sections [395], [397], [398], [815], [816], [817], [910], [911], [918], [919], [920] to [927],
[929] to [935], [936] to [942], [943] to [949]) – these sections can only be accessed using the installer code. Since there is no
default code, see System Codes on page 27 to set a default.
System Master Code
The default system master code is 1234. The system master code allows you to utilize any arming method, as well as program user
codes. To change the default code, see System Codes on page 27.
Panel Reset
Performing a panel reset will reset all panel settings to their preset, default values.
1. Press and hold the panel’s RESET button until the STATUS LED flashes (5 seconds).
2. Release the RESET button, and then push it once more, within two seconds.
To reset the panel to its default settings using section programming, see section [950] in Usability Sections, on page 52.
Entering Programming Mode
To enter programming mode, proceed as follows:
1. Press ENTER.
2. Enter your installer or maintenance code. Upon entering your code, the ARM and STAY LEDs will flash. To modify codes, see
System Codes on page 27.
3. Enter the three-digit section you wish to program. The ARM and STAY LEDs remain illuminated.
4. Enter required data.
NOTE: To enter programming mode, all zones must be disarmed and StayD mode deactivated. To deactivate StayD, press OFF,
enter your master or user code, and then press OFF.

Data Entry and Display

To access the data display mode, access the desired section and press ENTER before entering any data. Depending on the keypad(s)
configured to your system, specific LEDs or icons will flash, thus indicating that you are in data display mode. Each time ENTER is
pressed, the keypad will display the next digit in the current section, and will continue to do so through all the remaining sections,
one digit at a time, without changing the programmed values; this is not available for sections using the multiple feature select
method. Press CLEAR at any time, to exit data display mode.
There are two methods that can be used to enter data when in programming mode: single digit data entry and feature select
programming.
Single Digit Data Entry Method
After entering programming mode, some sections will require you to enter decimal values from 000 to 255. Other sections will
require that you enter hexadecimal values from 0 to F. The required data will be clearly indicated in this guide. When entering the
final digit in a section, the panel will automatically save and advance to the next section. See Decimal and Hexadecimal
Programming for details on the various keys, and their equivalent decimal and hexadecimal values.

3
Feature Select Programming Method
After entering certain sections, eight options will be displayed. In these instances, each option (from 1 to 8) represent a specific
feature. To turn enable the option, press the key corresponding to the desired option. Press the key again to remove the digit,
thereby, disabling the option. Press SLEEP to disable all eight options. When the options are set, press ENTER to save your settings
and advance to the next section.

Viewing Version Numbers

Table 1: Viewing panel and keypad version numbers

Step Action Details When Viewing Keypad Version

Enter viewing mode: The first digit is displayed Digit 1: ARM is illuminated
• For panel version, enter section [980] (usually 0)
1
• For keypad version, enter installer programming,
then press and hold ARM
2 Press ENTER The second digit is displayed Digit 2: SLEEP is illuminated
3 Press ENTER The third digit is displayed Digit 3: STAY is illuminated
4 Press ENTER The fourth digit is displayed Digit 4: OFF is illuminated

Example: Version 01.42

Digits 1-4

NOTE: For keypads K10V/H and K636, the keypad version numbers cannot be viewed.

Decimal and Hexadecimal Programming

Table 2: Decimal and hexadecimal values for 10 and 32-Zone LED keypads

Result
Value or Action Key
32-Zone LED 10-Zone LED
Value 0/replace current
SLEEP Erase digit and remain in section Erase digit and remain in section
digit with 0
Values 1 to 9 1 to 9 Zone 1 to 9 Keys 1 to 9
A (hex only) 0 Zone 10 Key 0 (10)
B (hex only) OFF Zone 11 OFF

C (hex only) BYP Zone 12 BYP

D (hex only) MEM Zone 13 MEM

E (hex only) TBL Zone 14 TBL

F (hex only) Zone 15

Exit without saving CLEAR Arm and Stay LEDs flash Arm and Stay LEDs flash
Save data (hex only) ENTER Advances to next section Advances to next section

4
SP+ Series Programming Guide

Contents List of Worksheets

Worksheet 1: Planning Bus Modules ................................................................................................. 8 Worksheet 57: Planning Bus Modules .............................................................................................. 8
Worksheet 2: Planning Wireless Keypads ........................................................................................ 9 Worksheet 58: Planning Wireless Keypads ..................................................................................... 9
Worksheet 3: Planning Wireless Sirens ............................................................................................. 9 Worksheet 59: Planning Wireless Sirens .......................................................................................... 9
Worksheet 4: Planning Programmable Outputs .........................................................................10 Worksheet 60: Planning Programmable Outputs ...................................................................... 10
Worksheet 5: Planning Wireless Repeaters ...................................................................................10 Worksheet 61: Planning Wireless Repeaters ................................................................................ 10
Worksheet 6: Planning Zones ............................................................................................................10 Worksheet 62: Planning Zones ......................................................................................................... 10
Worksheet 7: Zone Definitions ..........................................................................................................14 Worksheet 63: Zone Definitions ....................................................................................................... 14
Worksheet 8: Custom Zone Definitions .........................................................................................14 Worksheet 64: Custom Zone Definitions ...................................................................................... 14
Worksheet 9: Timers ..............................................................................................................................15 Worksheet 65: Timers ........................................................................................................................... 15
Worksheet 10: Wireless Zones ...........................................................................................................16 Worksheet 66: Wireless Zones ........................................................................................................... 16
Worksheet 11: Zone Report Codes ..................................................................................................16 Worksheet 67: Zone Report Codes .................................................................................................. 16
Worksheet 12: Zone Labels .................................................................................................................17 Worksheet 68: Zone Labels ................................................................................................................ 17
Worksheet 13: Programmable outputs for SP+ Series control panels ................................17 Worksheet 69: Programmable outputs for SP+ Series control panels ............................... 17
Worksheet 14: PGM Activation/Deactivation Events ................................................................24 Worksheet 70: PGM Activation/Deactivation Events ................................................................ 24
Worksheet 15: PGM Delays .................................................................................................................26 Worksheet 71: PGM Delays ................................................................................................................. 26
Worksheet 16: PGM Serial Numbers ................................................................................................26 Worksheet 72: PGM Serial Numbers ............................................................................................... 26
Worksheet 17: PGM Labels ..................................................................................................................26 Worksheet 73: PGM Labels ................................................................................................................. 26
Worksheet 18: User System Codes ...................................................................................................27 Worksheet 74: User System Codes .................................................................................................. 27
Worksheet 19: User Code Options ...................................................................................................27 Worksheet 75: User Code Options ................................................................................................... 27
Worksheet 20: User Report Codes ....................................................................................................28 Worksheet 76: User Report Codes ................................................................................................... 28
Worksheet 21: User Labels ..................................................................................................................28 Worksheet 77: User Labels .................................................................................................................. 28
Worksheet 22: Wireless Repeater Assignment ............................................................................29 Worksheet 78: Wireless Repeater Assignment ............................................................................ 29
Worksheet 23: Wireless Repeater Labels .......................................................................................31 Worksheet 79: Wireless Repeater Labels ....................................................................................... 31
Worksheet 24: Wireless Keypad Assignment ...............................................................................31 Worksheet 80: Wireless Keypad Assignment ............................................................................... 31
Worksheet 25: Wireless Keypad Labels ..........................................................................................33 Worksheet 81: Wireless Keypad Labels .......................................................................................... 33
Worksheet 26: Programming Remote Controls ..........................................................................34 Worksheet 82: Programming Remote Controls .......................................................................... 34
Worksheet 27: Wireless Siren Assignment ....................................................................................35 Worksheet 83: Wireless Siren Assignment .................................................................................... 35
Worksheet 28: Wireless Siren Labels ...............................................................................................35 Worksheet 84: Wireless Siren Labels ............................................................................................... 35
Worksheet 29: System Timers ............................................................................................................38 Worksheet 85: System Timers ........................................................................................................... 38
Worksheet 30: Keypad Lockout .........................................................................................................38 Worksheet 86: Keypad Lockout ........................................................................................................ 38
Worksheet 31: Daylight Savings Time ............................................................................................39 Worksheet 87: Daylight Savings Time ............................................................................................ 39
Worksheet 32: Partition Timers .........................................................................................................40 Worksheet 88: Partition Timers ......................................................................................................... 40
Worksheet 33: Partition Labels ..........................................................................................................40 Worksheet 89: Partition Labels ......................................................................................................... 40
Worksheet 34: SMS Site Name ...........................................................................................................40 Worksheet 90: SMS Site Name .......................................................................................................... 40
Worksheet 35: Bus Module Labels ...................................................................................................40 Worksheet 91: Bus Module Labels ................................................................................................... 40
Worksheet 36: Report Codes and Partition Accounts ...............................................................43 Worksheet 92: Report Codes and Partition Accounts ............................................................... 43
Worksheet 37: Landline Communication Settings .....................................................................43 Worksheet 93: Landline Communication Settings .................................................................... 43
Worksheet 38: Communication Timers .........................................................................................43 Worksheet 94: Communication Timers ......................................................................................... 43
Worksheet 39: Test Report and Report Delays ...........................................................................44 Worksheet 95: Test Report and Report Delays ........................................................................... 44
Worksheet 40: Special Arming and Disarming Report Codes ................................................44 Worksheet 96: Special Arming and Disarming Report Codes ................................................ 44
Worksheet 41: Special Alarm Report Codes .................................................................................44 Worksheet 97: Special Alarm Report Codes ................................................................................. 44
Worksheet 42: Special Trouble Report Codes ..............................................................................45 Worksheet 98: Special Trouble Report Codes ............................................................................. 45
Worksheet 43: System Trouble Restore Codes ............................................................................45 Worksheet 99: System Trouble Restore Codes ............................................................................ 45
Worksheet 44: System Special Report Codes ...............................................................................45 Worksheet 100: System Special Report Codes ............................................................................ 45
Worksheet 45: Communication Report Codes ............................................................................50 Worksheet 101: Communication Report Codes ......................................................................... 50
Worksheet 46: Communication Restore Report Codes ............................................................50 Worksheet 102: Communication Restore Report Codes ......................................................... 50
Worksheet 47: Additional Communication Timers ...................................................................50 Worksheet 103: Additional Communication Timers ................................................................ 50
Worksheet 48: BabyWare Options ...................................................................................................51 Worksheet 104: BabyWare Options ................................................................................................. 51
Worksheet 49: IP Account Numbers ...............................................................................................51 Worksheet 105: IP Account Numbers ............................................................................................ 51
Worksheet 50: Software and PCS Connection Settings ............................................................51 Worksheet 106: Software and PCS Connection Settings ......................................................... 51
Worksheet 51: IP Receiver 1 Configuration ...................................................................................52 Worksheet 107: IP Receiver 1 Configuration ................................................................................ 52
Worksheet 52: IP Receiver 2 Configuration ...................................................................................52 Worksheet 108: IP Receiver 2 Configuration ................................................................................ 52
Worksheet 53: IP Receiver Backup Configuration ......................................................................52 Worksheet 109: IP Receiver Backup Configuration ................................................................... 52
Worksheet 54: System Timers ............................................................................................................63 Worksheet 110: System Timers ......................................................................................................... 63
Worksheet 55: Keypad Lockout .........................................................................................................64 Worksheet 111: Keypad Lockout ...................................................................................................... 64
Worksheet 56: Communication Timers .........................................................................................64 Worksheet 112: Communication Timers ...................................................................................... 64

5
 Walk Test Mode

Installer Quick Menu Step Action Details

= flash; maintenance code may also be

1 + installer code
used
Zones
2 -
Step Action Details 3 6 Activates or deactivates walk test mode
= flash; programmed zones are lit (buttons
1 + installer code or LED, depending on keypad); maintenance Installer and Maintenance Codes
code may also be used
Step Action Details
2 Zone number Two digits: 01 to 32
1 + installer code = flash
Wireless zone: open/close cover or press
LEARN/TAMPER switch; for 2WPGM remove and 2 -
re-install Jumper 2 (JP2)
3 Enroll or erase zone • 7 for installer
hardwired zone: press ENTER;
code
to erase a programmed zone, press and hold
3 • 8 for -
SLEEP for three seconds
maintenance
See Zone Definitions on page 13, for the zone code
4 Zone type
type
4 Code Enter a four or six-digit code
If applicable, assign the zone to one or both
Assign partition 5 Confirm code Re-enter the four or six-digit code, to confirm
5 partitions, and then press ENTER; by default, all
(1 and/or 2 + ENTER)
zones are assigned to partition 1 NOTE: To erase a code, press and hold SLEEP for three seconds.
NOTE: If applicable, partition 2 status LEDs display signal strength of selected
wireless zone (4 LEDs = best signal; 1 LED = weak signal; no LEDs = hardwired BabyWare
panel/keypad zone).
Step Action Details
Delays 1 + installer code = flash
2 -
Step Action Details
3 9 -
= flash; maintenance code may also be
1 + installer code Enter PC phone number (up to 32 digits), and
used 4 Phone # + ENTER
then press ENTER
2 -
5 Panel ID Enter four-digit panel ID
1 = entry delay 1 Default: 045 sec.
6 PC password Enter four-digit PC password
2 = entry delay 2 Default: 045 sec.
3 NOTE: To erase the BabyWare phone number, panel ID, and PC password,
3 = exit delay Default: 060 sec. press and hold SLEEP for three seconds.
4 = bell cut-off Default: 004 min.
Entry/exit delay = seconds; Monitoring Phone Number
4 000 to 255
bell cut-off = minutes
Step Action Details
Time and Date 1 + installer code = flash
2 -
Step Action Details
3 1 -
= flash; maintenance code may also be
1 + installer code Enter monitoring station phone number (up
used 4 Phone # + ENTER
to 32 digits), and then press ENTER
2 +5 -
5 Partition 1 account # -
3 Time (HH:MM) If HH = 13 or more, go to step 5
• 1 for CID
4 Time format 1 = 24 hr. format, 2 = AM, 3 = PM 6 SIA is not supported with GPRS/IP reporting
• 2 for SIA
5 Date (YYYY/MM/DD) Enter the year/month/day 7 Partition 2 account # -
NOTE: To erase monitoring phone number, reporting format, and account
numbers, press and hold SLEEP for three seconds.

6
SP+ Series Programming Guide

Communicator Keypad Input/Output Configuration (K636 V2.0 and higher)

Step Action Details
Step Action Details
= flash; maintenance code may also be
1 + installer code 1 ENTER + installer code ARM + STAY = flash
used
2 - Press and hold ENTER
2 ARM + STAY = ON
2 = backup phone # for three seconds
3 = personal phone #1 ON = output switches to ground following
4 = personal phone #2 3 Option 1 system arming (blue wire, maximum150 mA)
3 OFF = input (keypad zone input)
5 = personal phone #3
6 = personal phone #4 ON = output N.C.
4 Option 2
OFF = output N.O.
7 = personal phone #5
Enter phone number (up to 32 digits), and NOTE: When configuring as an output, clear the assigned keypad zone first.
then press ENTER to proceed to the next phone
4 Phone # + ENTER
number, or go to step 5 if option 8 was
PGMs
selected
Step Action Details
Cancel Communication = flash; maintenance code may also be
1 + installer code
Step Action Details used
= flash; maintenance code may also be 2 -
1 + installer code
used 3 PGM number Two digits: 01 to 16
2 -
Wireless PGM = press the LEARN/TAMPER switch
Cancels all communication with BabyWare and 4 Enroll or erase PGM or remove and re-install Jumper 2 (JP2) on
3 9
PCS module module; hardwired PGM = press ENTER
Keypad Programming 1 = Follow button or
Assigning Keypad Zone Numbers 2 = Follow button or
Step Action Details 3 = Follow zone
ARM + STAY = flash; maintenance code may
1 ENTER + installer code 4 = Follow alarm
also be used 5 PGM type
5 = Follow bell
Press and hold for
2 ARM + STAY = ON
three seconds 6 = Follow arm
K35, K32, K32LCD, K32LX = two digits: 01 to 32; 7 = Follow Stay arm
3 Zone number + ENTER
K636, K10V/H = one digit: 1 to 0 (10)
8 = Follow Sleep arm
NOTE: To erase a keypad zone number, press CLEAR, and then ENTER.
1 = Follow
Assigning Keypad Zone Numbers TM50/TM70
2 = 1 sec.
Step Action Details
3 = 5 sec.
Press and hold MENU Enters into advanced programming
1 4 = 15 sec.
+ installer code If PGM type is 1, 2, 3, or
2 Program this unit Ensure that zone temperature input is enabled 4, enter activation 5 = 30 sec.
Press keypad zone Select your zone delay
3 6 = 1 min.
number
7 = 5 min.
6
Entry Point Zone Assignment (StayD) 8 = 15 min.
Step Action Details
9 = 30 min.
1 ENTER + installer code ARM + STAY = flash
If PGM type is 5, proceed
Press and hold OFF for to the next available -
2 ARM + STAY = ON
three seconds PGM
K35, K32RF, K37, K32LCD, K32LX = two digits:
If system is partitioned, select partition(s), and
01 to 32; K636, K10V/H = one digit: 1 to 0 (10; If PGM type is 6, 7, or 8,
then press ENTER to proceed to the next available
maximum ten zones); the first zone enter 1 and/or 2 + ENTER
PGM
3 Zone number programmed will be the designated entry
point and will flash; up to three more path If PGM type is 1 or 2,
01 to 32 (00 = all remote controls); the control
zones can be added – these zones will light up enter two-digit remote
panel proceeds to the next available PGM
and remain lit control #

4 ENTER Press ENTER to save and exit If PGM type is 3, enter 01 to 32 (00 = all zones); the control panel
7
two-digit zone # proceeds to the next available PGM
If system is partitioned, select partition(s), and
If PGM type is 4, enter 1
then press ENTER to proceed to the next available
and/or 2 + ENTER
PGM
NOTE: To erase a PGM, press and hold SLEEP for three seconds.

7
 SP+ Series Programming Guide

System Planning Bus Module Planning

Worksheet 1: Planning Bus Modules
Serial # Sticker Description Path Zone (Entry Point) Path Zone Path Zone Path Zone

Bus Module 1

Bus Module 2

Bus Module 3

Bus Module 4

Bus Module 5

Bus Module 6

Bus Module 7

Bus Module 8

Bus Module 9

Bus Module 10

Bus Module 11

Bus Module 12

Bus Module 13

Bus Module 14

Bus Module 15

NOTE: Paths are only applicable when StayD is enabled.

Wireless Keypad Planning

8
SP+ Series Programming Guide

Worksheet 2: Planning Wireless Keypads

Serial # Sticker Description Path Zone (Entry Point) Path Zone Path Zone Path Zone

Wireless Keypad
1

Wireless Keypad
2

Wireless Keypad
3

Wireless Keypad
4

Wireless Keypad
5

Wireless Keypad
6

Wireless Keypad
7

Wireless Keypad
8

NOTE: When deleting a wireless keypad (K32RF/K37) from the system, the corresponding StayD path zones will also be deleted.

Wireless Siren Planning

Worksheet 3: Planning Wireless Sirens
Serial # Sticker Description Serial # Sticker Description

Siren 1 Siren 3

Siren 2 Siren 4

Programmable Output (PGM) Planning

9
 SP+ Series Programming Guide

Worksheet 4: Planning Programmable Outputs

Serial # Sticker Description Serial # Sticker Description

PGM 1 PGM 9

PGM 2 PGM 10

PGM 3 PGM 11

PGM 4 PGM 12

PGM 5 PGM 13

PGM 6 PGM 14

PGM 7 PGM 15

PGM 8 PGM 16

Wireless Repeater Planning

Worksheet 5: Planning Wireless Repeaters
Serial # Sticker Description Serial # Sticker Description

Repeater 1 Repeater 2

Zone Planning
Worksheet 6: Planning Zones
Arming Method Arming Method
Serial # Sticker Zone # Zone Description Stay Sleep Full Serial # Sticker Zone # Zone Description Stay Sleep Full

Zone    Zone   

Zone    Zone   

Zone    Zone   

10
SP+ Series Programming Guide

Worksheet 6: Planning Zones (Continued)

Arming Method Arming Method
Serial # Sticker Zone # Zone Description Stay Sleep Full Serial # Sticker Zone # Zone Description Stay Sleep Full

Zone    Zone   

Zone    Zone   

Zone    Zone   

Zone    Zone   

Zone    Zone   

Zone    Zone   

Zone    Zone   

Zone    Zone   

Zone    Zone   

Zone    Zone   

Zone    Zone   

Zone    Zone   

Zone    Zone   

11
 SP+ Series Programming Guide

Zone Recognition
NOTE: For keypad zone programming, see Keypad Programming on page 7.
When expanding zones via ZX8/ZX82, up to three ZX8/ZX82 modules can be added to the system, and they are identified by the ZX8/ZX82 three-position jumpers:
+1, +9, and +17. Table 3 displays zone recognition information for SP+ control panels.
NOTE: If a device is assigned to a zone which is already programmed, a wireless zone will overwrite a keypad/hardwire zone and a keypad zone will overwrite a
hardwire zone.
Table 3: Zone recognition information for the SP+ series

SP6000+
SP5500+ SP6000+ (with ATZ)* SP7000+

Type Zone Description Type Zone Description Type Zone Description Type Zone Description

1 Panel input 1 1 Panel input 1 1 Panel input 1A 1 Panel input 1

2 Panel input 2 2 Panel input 2 2 Panel input 2A 2 Panel input 2
Panel 3 Panel input 3 3 Panel input 3 3 Panel input 3A 3 Panel input 3
4 Panel input 4 4 Panel input 4 4 Panel input 4A 4 Panel input 4
Panel
5 Panel input 5 5 Panel input 5 5 Panel input 5A 5 Panel input 5
6 Input 1 6 Panel input 6 6 Panel input 6A 6 Panel input 6
7 Input 2 7 Panel input 7 7 Panel input 7A 7 Panel input 7
8 Input 3 8 Panel input 8 8 Panel input 8A 8 Panel input 8
Panel Panel
ZX8 9 Input 4 9 Input 1 9 Panel input 1B 9 Panel input 9
Jumper
Panel + 1 10 Input 5 10 Input 2 10 Panel input 2B 10 Panel input 10
11 Input 6 11 Input 3 11 Panel input 3B 11 Panel input 11
12 Input 7 ZX8 12 Input 4 12 Panel input 4B 12 Panel input 12
Jumper
13 Input 8 Panel + 1 13 Input 5 13 Panel input 5B 13 Panel input 13
14 Input 1 14 Input 6 14 Panel input 6B 14 Panel input 14
15 Input 2 15 Input 7 15 Panel input 7B 15 Panel input 15
16 Input 3 16 Input 8 16 Panel input 8B 16 Panel input 16
ZX8 17 Input 4 17 Input 1 17 Input 1 17 Input 1
Jumper
Panel + 9 18 Input 5 18 Input 2 18 Input 2 18 Input 2
ZX8/
19 Input 6 19 Input 3 ZX82Z 19 Input 3 19 Input 3
ZX8
20 Input 7 20 Input 4 X8/ 20 Input 4 ZX8 20 Input 4
Jumper
ZX82 Jumper
21 Input 8 Panel + 9 21 Input 5 21 Input 5 21 Input 5
Jumpe Panel +
22 Input 1 22 Input 6 r Panel 22 Input 6 22 Input 6
+1
23 Input 2 23 Input 7 23 Input 7 23 Input 7
24 Input 3 24 Input 8 24 Input 8 24 Input 8
ZX8
Jumper 25 Input 4 25 Input 1 25 Input 1 25 Input 1
Panel + 26 Input 5 26 Input 2 26 Input 2 26 Input 2
17
27 Input 6 27 Input 3 ZX8/ 27 Input 3 27 Input 3
ZX8
28 Input 7 28 Input 4 ZX82 28 Input 4 ZX8 28 Input 4
Jumper
Jumpe Jumper
29 Input 8 Panel + 29 Input 5 29 Input 5 29 Input 5
r Panel Panel + 9
17
30 - 30 Input 6 +9 30 Input 6 30 Input 6
- 31 - 31 Input 7 31 Input 7 31 Input 7
32 - 32 Input 8 32 Input 8 32 Input 8

* Please note that ATZ is only supported on the SP6000+.

12
SP+ Series Programming Guide

Zone Definitions
NOTE: If a device is assigned to a zone which is already programmed, a wireless zone will overwrite a keypad/hardwire zone and a keypad zone will overwrite a
hardwire zone.
To define zones on your SP+ control panel:
1. Press ENTER, and then enter your installer code (maintenance code may also be used). The ARM and STAY functions will flash.
2. Enter the three-digit zone number you wish to program (e.g., 001 to 032). The ARM and STAY functions will remain illuminated.
3. Enter a two-digit zone definition, by referring to table 4.
4. Assign a partition, by referring to table 5. By default, all zones are assigned to partition 1.
5. Select or deselect zone options, using buttons 1 to 8 (see tables 6 and 7).
6. Press ENTER to save and proceed to the next zone.
7. Repeat steps 3 to 6 for all remaining zones.
Table 4: Zone definitions for SP+ Series panels Table 5: Partition assignment for SP+ Series panels

Arming Type Input Value Description

Input Value Description
Stay Arm Sleep Arm Fully Arm 1 Assign to partition 1
00 Disabled (default) - - - 2 Assign to partition 2
01 Entry delay 1 Entry delay 1 Entry delay 1 Entry delay 1 3 Assign to both partitions
02 Entry delay 2 Entry delay 2 Entry delay 2 Entry delay 2 NOTE: When using the K636 keypad, only
partition 1 is available.
03 Entry delay 1 (Full Arm) Not armed Not armed Entry delay 1
04 Entry delay 2 (Full Arm) Not armed Not armed Entry delay 2 Table 6: Zone options for SP+ Series panels
05 Follow Follow* Follow* Follow
Input
06 Follow (sleep/full arm) Not armed Follow* Follow Description
Value
07 Follow (full arm) Not armed Not armed Follow 1 Auto zone shutdown
08 Instant Instant* Instant* Instant 2 Bypassable zone
09 Instant (sleep/full arm) Not armed Instant* Instant 3 RF zone supervision
10 Instant (full arm) Not armed Not armed Instant 6 Intellizone
11 Instant fire† - - - 7 Delay alarm transmission
12 Delayed fire† - - - 8 Force zone
13 Instant fire silent† - - - Input Value
Zone Alarm Type
14 Delayed fire silent† - - - 4 5
15 24 hr. buzzer - - - OFF OFF Audible alarm
16 24 hr. burglary - - - OFF ON Pulsed alarm
17 24 hr. hold-up - - - ON OFF Silent alarm
18 24 hr. gas - - - ON ON Report only
19 24 hr. heat - - - NOTE: For additional zone options, see Zone
20 24 hr. water - - - Options on page 37.

21 24 hr. freeze - - -
Table 7: Keyswitch options for SP+ Series panels
22 24 hr. panic‡ - - -
Input
23 Follow no pre-alarm - - - Description
Value
24 Instant no pre-alarm - - -
1 -
25 Keyswitch maintain** - - -
2 -
26 Keyswitch momentary** - - -
3 -
33 Instant no pre-alarm (stay/sleep) Instant Instant Not armed
OFF = Disarm; ON = Disarm only
34 Instant no pre-alarm (sleep) Not armed Instant Not armed 4
if Stay/Sleep armed
35 Entry delay 1 (stay/full)/instant Entry delay 1 Instant Entry delay 1 5 Arm only
36 Entry delay 1 (full arm)/instant Instant Instant Entry delay 1 6 Stay arming*
* Flex-instant: zone will follow the delay at section [720] (default is 15 seconds/0 = instant zone). 7 Sleep arming*
** On-board, hardwire, control panel zones only.
8 -
† ZX8/ZX82 inputs do not support fire zones. For two-wire smoke installations these definitions apply to
zone 1 input only. Section [706], option 3, must be enabled. For four-wire smoke installations, use any panel, * Select only one. If all are OFF, keyswitch will
on-board zone input. regular arm.
‡ This alarm will follow the panic 1 option (section [702], option 1).

13
 Table 8: Permitted zone definitions
14

Arming Type Arming Type

Input Input
Description Stay Sleep Fully Description Stay Sleep Fully
Value Disarm Value Disarm
Arm Arm Arm Arm Arm Arm
00 Zone disabled     16 24 hr. burglary    
01 Entry delay 1 -    17 24 hr. hold-up    
02 Entry delay 2 -    18 24 hr. gas    
03 Entry delay 1 (Full Arm) - - -  19 24 hr. heat    
04 Entry delay 2 (Full Arm) - - -  20 24 hr. water    
05 Follow -    21 24 hr. freeze    
06 Follow (sleep/full arm) - -   22 24 hr. panic    
07 Follow (full arm) - - -  23 Follow no pre-alarm -   
08 Instant -    24 Instant no pre-alarm -   
09 Instant (sleep/full arm) - -   25 Keyswitch maintain    
10 Instant (full arm) - - -  26 Keyswitch momentary    
11 Instant fire     33 Instant no pre-alarm (stay/sleep) -   -
12 Delayed fire     34 Instant no pre-alarm (sleep) - -  -
13 Instant fire silent     35 Entry delay 1 (stay/full)/instant -   
14 Delayed fire silent     36 Entry delay 1 (full arm)/instant -   
15 24 hr. buzzer    

Worksheet 7: Zone Definitions

Section Zone Description (see tables 3 and 4) Zone Definition Partition Zone Options Section Zone Description (see tables 3 and 4) Zone Definition Partition Zone Options
[001] 1 ________________________ ____/____ ______ 1 2 3 4 5 6 7 8 [017] 17 ________________________ ____/____ ______ 1 2 3 4 5 6 7 8
[002] 2 ________________________ ____/____ ______ 1 2 3 4 5 6 7 8 [018] 18 ________________________ ____/____ ______ 1 2 3 4 5 6 7 8
[003] 3 ________________________ ____/____ ______ 1 2 3 4 5 6 7 8 [019] 19 ________________________ ____/____ ______ 1 2 3 4 5 6 7 8
[004] 4 ________________________ ____/____ ______ 1 2 3 4 5 6 7 8 [020] 20 ________________________ ____/____ ______ 1 2 3 4 5 6 7 8
[005] 5 ________________________ ____/____ ______ 1 2 3 4 5 6 7 8 [021] 21 ________________________ ____/____ ______ 1 2 3 4 5 6 7 8
[006] 6 ________________________ ____/____ ______ 1 2 3 4 5 6 7 8 [022] 22 ________________________ ____/____ ______ 1 2 3 4 5 6 7 8
[007] 7 ________________________ ____/____ ______ 1 2 3 4 5 6 7 8 [023] 23 ________________________ ____/____ ______ 1 2 3 4 5 6 7 8
[008] 8 ________________________ ____/____ ______ 1 2 3 4 5 6 7 8 [024] 24 ________________________ ____/____ ______ 1 2 3 4 5 6 7 8
[009] 9 ________________________ ____/____ ______ 1 2 3 4 5 6 7 8 [025] 25 ________________________ ____/____ ______ 1 2 3 4 5 6 7 8
[010] 10 ________________________ ____/____ ______ 1 2 3 4 5 6 7 8 [026] 26 ________________________ ____/____ ______ 1 2 3 4 5 6 7 8
[011] 11 ________________________ ____/____ ______ 1 2 3 4 5 6 7 8 [027] 27 ________________________ ____/____ ______ 1 2 3 4 5 6 7 8
[012] 12 ________________________ ____/____ ______ 1 2 3 4 5 6 7 8 [028] 28 ________________________ ____/____ ______ 1 2 3 4 5 6 7 8
[013] 13 ________________________ ____/____ ______ 1 2 3 4 5 6 7 8 [029] 29 ________________________ ____/____ ______ 1 2 3 4 5 6 7 8
[014] 14 ________________________ ____/____ ______ 1 2 3 4 5 6 7 8 [030] 30 ________________________ ____/____ ______ 1 2 3 4 5 6 7 8
[015] 15 ________________________ ____/____ ______ 1 2 3 4 5 6 7 8 [031] 31 ________________________ ____/____ ______ 1 2 3 4 5 6 7 8
[016] 16 ________________________ ____/____ ______ 1 2 3 4 5 6 7 8 [032] 32 ________________________ ____/____ ______ 1 2 3 4 5 6 7 8
NOTE: See worksheet 10 on page 16, for assigning wireless zones to your SP+ Series control panels.
 Custom Zone Definitions
With SP+ Series control panels you can create up to four custom zone definition templates (use worksheet 8). Custom zone definition templates (sections [033] to [036]) will overwrite zone definitions 33 to 36 in
table 4 on page 13. Modifications can be made in accordance with table 8 (Permitted zone definitions), on page 14.

Worksheet 8: Custom Zone Definitions

Section Description Disarm Stay Arm Sleep Arm Full Arm
[033] Zone definition template 1 _____/_____ _____/_____ _____/_____ _____/_____
[034] Zone definition template 2 _____/_____ _____/_____ _____/_____ _____/_____
[035] Zone definition template 3 _____/_____ _____/_____ _____/_____ _____/_____
[036] Zone definition template 4 _____/_____ _____/_____ _____/_____ _____/_____

Zone Timers
Use the following section to program zone timers for your SP+ Series control panels. Use worksheets 9 and 10 to record your settings.
NOTE: When both ATZ (SP6000+ only) and EOL are enabled, the zone speed should not be set below 300 msec.
Worksheet 9: Timers
Section Zone SP5500+ SP6000+ SP7000+ Data Description (default: 060)
[041] 1 (Z1) (Z1) (Z1) ____/____/____ (000 to 255) x 10 msec. Speed of hardwire zone 1
[042] 2 (Z2) (Z2) (Z2) ____/____/____ (000 to 255) x 10 msec. Speed of hardwire zone 2
[043] 3 (Z3) (Z3) (Z3) ____/____/____ (000 to 255) x 10 msec. Speed of hardwire zone 3
[044] 4 (Z4) (Z4) (Z4) ____/____/____ (000 to 255) x 10 msec. Speed of hardwire zone 4
[045] 5 (Z5) (Z5) (Z5) ____/____/____ (000 to 255) x 10 msec. Speed of hardwire zone 5
[046] 6 (Z6) (Z6) ____/____/____ (000 to 255) x 10 msec. Speed of hardwire zone 6
[047] 7 (Z7) (Z7) ____/____/____ (000 to 255) x 10 msec. Speed of hardwire zone 7
[048] 8 (Z8) (Z8) ____/____/____ (000 to 255) x 10 msec. Speed of hardwire zone 8
[049] 9 (Z1 ATZ) (Z9) ____/____/____ (000 to 255) x 10 msec. Speed of hardwire zone 9
[050] 10 (Z2 ATZ) (Z10) ____/____/____ (000 to 255) x 10 msec. Speed of hardwire zone 10
[051] 11 (Z3 ATZ) (Z11) ____/____/____ (000 to 255) x 10 msec. Speed of hardwire zone 11
[052] 12 (Z4 ATZ) (Z12) ____/____/____ (000 to 255) x 10 msec. Speed of hardwire zone 12
[053] 13 (Z5 ATZ) (Z13) ____/____/____ (000 to 255) x 10 msec. Speed of hardwire zone 13
[054] 14 (Z6 ATZ) (Z14) ____/____/____ (000 to 255) x 10 msec. Speed of hardwire zone 14
[055] 15 (Z7 ATZ) (Z15) ____/____/____ (000 to 255) x 10 msec. Speed of hardwire zone 15
[056] 16 (Z8 ATZ) (Z16) ____/____/____ (000 to 255) x 10 msec. Speed of hardwire zone 16
15
 SP+ Series Programming Guide

Wireless Zone Assignment

Use the following section to program the wireless zones on your SP+ Series control panels. Use worksheet 10 to record your settings.

Worksheet 10: Wireless Zones

Section Zone Wireless Zone (Serial #) Section Zone Wireless Zone (Serial #) Section Zone Wireless Zone (Serial #)
[061] 1 ___/___/___/___/___/___ [072] 12 ___/___/___/___/___/___ [083] 23 ___/___/___/___/___/___
[062] 2 ___/___/___/___/___/___ [073] 13 ___/___/___/___/___/___ [084] 24 ___/___/___/___/___/___
[063] 3 ___/___/___/___/___/___ [074] 14 ___/___/___/___/___/___ [085] 25 ___/___/___/___/___/___
[064] 4 ___/___/___/___/___/___ [075] 15 ___/___/___/___/___/___ [086] 26 ___/___/___/___/___/___
[065] 5 ___/___/___/___/___/___ [076] 16 ___/___/___/___/___/___ [087] 27 ___/___/___/___/___/___
[066] 6 ___/___/___/___/___/___ [077] 17 ___/___/___/___/___/___ [088] 28 ___/___/___/___/___/___
[067] 7 ___/___/___/___/___/___ [078] 18 ___/___/___/___/___/___ [089] 29 ___/___/___/___/___/___
[068] 8 ___/___/___/___/___/___ [079] 19 ___/___/___/___/___/___ [090] 30 ___/___/___/___/___/___
[069] 9 ___/___/___/___/___/___ [080] 20 ___/___/___/___/___/___ [091] 31 ___/___/___/___/___/___
[070] 10 ___/___/___/___/___/___ [081] 21 ___/___/___/___/___/___ [092] 32 ___/___/___/___/___/___
[071] 11 ___/___/___/___/___/___ [082] 22 ___/___/___/___/___/___
NOTE: When assigning wireless zones, enter the serial number, or press TAMPER/LEARN; for the 2WPGM, remove and re-install Jumper 2 (JP2). To delete the serial
number, enter 000000.

Wireless Transmitter Signal Strength

The signal strength test for wireless transmitters is performed in sections [101] to [132]; these sections represent zones 1 to 32, respectively. To test the wireless
transmitter strength of your various wireless devices, proceed as follows:
1. Enter the zone’s respective section (e.g., for zone 1, enter section [101]).
2. For all wireless transmitters except 2WPGM: Press the transmitter’s anti-tamper switch and note the number of beeps which are emitted. As shown in table 9,
the number of beeps correspond to a preset signal strength range.
For the 2WPGM: Remove and re-install Jumper 2 (JP2).
Table 9: Signal strength indicator for wireless transmitters

Number of Beeps Signal Strength Result

3 8 to 10 Strong signal
2 5 to 7 Average signal
1 1 to 4 Weak signal (relocate)
NOTE: The visual representation of a transmitter’s signal strength is dependent on the type of keypad. For LED keypads, zones 1 through 10 will illuminate,
depending on the signal strength. For instance, a signal strength of 8 will result in zones 1 through 8 to illuminate. For LCD keypads, a ten-level progress bar
composed of arrows will appear, followed by the numeric value. For a signal strength of 8, eight arrows will appear, followed by the number 8.

Zone Report Codes and Labels

Use the following section to program zone report codes and labels on your SP+ Series control panels.

Zone Report Codes

Use worksheet 11 to record your settings when programming zone report codes.

Worksheet 11: Zone Report Codes

Alarm Alarm Tamper Tamper Alarm Alarm Tamper Tamper
Section Zone Report Restore Report Restore Section Zone Report Restore Report Restore
Codes Report Codes Codes Report Codes Codes Report Codes Codes Report Codes
[141] 1 ___/___ ___/___ ___/___ ___/___ [157] 17 ___/___ ___/___ ___/___ ___/___
[142] 2 ___/___ ___/___ ___/___ ___/___ [158] 18 ___/___ ___/___ ___/___ ___/___
[143] 3 ___/___ ___/___ ___/___ ___/___ [159] 19 ___/___ ___/___ ___/___ ___/___
[144] 4 ___/___ ___/___ ___/___ ___/___ [160] 20 ___/___ ___/___ ___/___ ___/___
[145] 5 ___/___ ___/___ ___/___ ___/___ [161] 21 ___/___ ___/___ ___/___ ___/___
[146] 6 ___/___ ___/___ ___/___ ___/___ [162] 22 ___/___ ___/___ ___/___ ___/___
[147] 7 ___/___ ___/___ ___/___ ___/___ [163] 23 ___/___ ___/___ ___/___ ___/___
[148] 8 ___/___ ___/___ ___/___ ___/___ [164] 24 ___/___ ___/___ ___/___ ___/___
[149] 9 ___/___ ___/___ ___/___ ___/___ [165] 25 ___/___ ___/___ ___/___ ___/___
[150] 10 ___/___ ___/___ ___/___ ___/___ [166] 26 ___/___ ___/___ ___/___ ___/___
[151] 11 ___/___ ___/___ ___/___ ___/___ [167] 27 ___/___ ___/___ ___/___ ___/___
[152] 12 ___/___ ___/___ ___/___ ___/___ [168] 28 ___/___ ___/___ ___/___ ___/___
[153] 13 ___/___ ___/___ ___/___ ___/___ [169] 29 ___/___ ___/___ ___/___ ___/___
[154] 14 ___/___ ___/___ ___/___ ___/___ [170] 30 ___/___ ___/___ ___/___ ___/___
[155] 15 ___/___ ___/___ ___/___ ___/___ [171] 31 ___/___ ___/___ ___/___ ___/___
[156] 16 ___/___ ___/___ ___/___ ___/___ [172] 32 ___/___ ___/___ ___/___ ___/___

16
SP+ Series Programming Guide

Zone Labels
Use worksheet 12 to record your settings when programming zone labels.

Worksheet 12: Zone Labels

Section Zone Zone Label Section Zone Zone Label
[181] 1 __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__ [197] 17 __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
[182] 2 __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__ [198] 18 __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
[183] 3 __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__ [199] 19 __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
[184] 4 __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__ [200] 20 __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
[185] 5 __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__ [201] 21 __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
[186] 6 __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__ [202] 22 __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
[187] 7 __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__ [203] 23 __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
[188] 8 __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__ [204] 24 __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
[189] 9 __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__ [205] 25 __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
[190] 10 __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__ [206] 26 __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
[191] 11 __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__ [207] 27 __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
[192] 12 __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__ [208] 28 __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
[193] 13 __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__ [209] 29 __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
[194] 14 __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__ [210] 30 __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
[195] 15 __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__ [211] 31 __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
[196] 16 __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__ [212] 32 __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__

Programmable Output Programming

Use the following section to program programmable outputs (PGMs) on your SP+ Series control panel.

Programmable Output Recognition

Worksheet 13: Programmable outputs for SP+ Series control panels

Control Panel
PGM PGM Output
SP5500+ SP6000+ SP7000+
1 Control panel output 1   
2 Control panel output 2   
3 Control panel output 3 - Optional 
4 Control panel output 4 - Optional 
5 Control panel relay - Optional 
6 ZX8/ZX82 ID = 1 output   
7 ZX8/ZX82 ID = 2 output   
8 ZX8/ZX82 ID = 3 output   -
9 PGM4/PGM82 relay 1   
10 PGM4 /PGM82 relay 2   
11 PGM4/PGM82 relay 3   
12 PGM4/PGM82 relay 4   
13 RTX3/RX1 output 1   
14 RTX3/RX1 output 2   
15 RTX3 output 3 (relay)   
16 RTX3 output 4 (relay) Optional Optional Optional

NOTE: A wireless PGM module can be assigned to any PGM. These modules will work in parallel with the control panel output.
Programmable Output on the K32LCD/K32LX
The on-board PGM of the K32LCD and K32LX (not programmable) will follow the arm status of any partition, via any arming method, including StayD.

17
 SP+ Series Programming Guide

Description of Events
Table 10: List of events

Event Group Event Group Description Sub-group Sub-group Description

00 Zone OK 01 to 32 Zone number
01 Zone open 99 Any zone number
00 to 01 -
02 Silent alarm
03 Buzzer alarm
04 Steady alarm
05 Pulsed alarm
06 Strobe
07 Alarm stopped
08 Squawk ON (partition 1only)
02 Partition status 09 Squawk OFF (partition 1 only)
10 Ground start (partition 1 only)
11 Disarm partition
12 Arm partition
13 Entry delay started
14 Exit delay started
15 Pre-alarm delay
16 Report confirmation
99 Any partition status event
00 Bell OFF
01 Bell ON
03 Bell status (partition 1 only) 02 Bell squawk arm
03 Bell squawk disarm
99 Any bell status event
00 Telephone line trouble
01 CLEAR + ENTER, or was pressed for 3 secs. (partition 1 only)
02 -
03 Arm in Stay mode
04 Arm in Sleep mode
05 Arm in Force mode
06 Full arm when armed in Stay mode
07 PC fail to communicate (partition 1 only)
08 Utility key 1 pressed (keys 1 and 2; partition 1 only)
09 Utility key 2 pressed (keys 4 and 5; partition 1 only)
10 Utility key 3 pressed (keys 7 and 8; partition 1 only)
11 Utility key 4 pressed (keys 2 and 3; partition 1 only)
06 Non-reportable event 12 Utility key 5 pressed (keys 5 and 6; partition 1 only)
13 Utility key 6 pressed (keys 8 and 9; partition 1 only)
14 Tamper generated alarm
15 Supervision loss generated alarm
16 -
17 -
18 -
19 -
20 Full arm when armed in Sleep mode
21 Firmware upgrade (partition 1 only; non-PGM event)
22 -
23 StayD mode activated
24 StayD mode deactivated

18
SP+ Series Programming Guide

Table 10: List of events

Event Group Event Group Description Sub-group Sub-group Description

25 IP registration status change
26 GPRS registration status change
27 Armed with trouble(s)
06 Non-reportable event
28 Supervision alert
(Cont.) (Cont.)
29 Supervision alert restore
30 Armed with remote with low battery
99 Any non-reportable event

Button pressed on remote (see Default Data B, in worksheet 26 01 to 32 Remote control number
08
on page 34) 99 Any remote control number

Button pressed on remote (see Default Data C, in worksheet 26 01 to 32 Remote control number
09
on page 34) 99 Any remote control number

Button pressed on remote (see Default Data D, in worksheet 26 01 to 32 Remote control number
10
on page 34) 99 Any remote control number

Button pressed on remote (see Default Data E, in worksheet 26 01 to 32 Remote control number
11
on page 34) 99 Any remote control number
01 to 32 Zone number
12 Cold start wireless zone
99 Any zone number
01 to 16 Output number
17 to 18 Wireless repeater
13 Cold start wireless module (partition 1 only) 19 to 26 Wireless keypad
27 to 30 Wireless siren
99 Any output number
01 to 32 User number
14 Bypass programming
99 Any user number
01 to 32 User number
15 User code activated output (partition 1 only)
99 Any user number
01 to 32 Zone number
16 Wireless smoke maintenance signal
99 Any zone number
01 to 32 Zone number
17 Delay zone alarm transmission
99 Any zone number
01 to 32 Zone number
18 Zone signal strength weak 1 (partition 1 only)
99 Any zone number
01 to 32 Zone number
19 Zone signal strength weak 2 (partition 1 only)
99 Any zone number
01 to 32 Zone number
20 Zone signal strength weak 3 (partition 1 only)
99 Any zone number
01 to 32 Zone number
21 Zone signal strength weak 4 (partition 1 only)
99 Any zone number
01 to 32 Remote control number
22 Button pressed on remote (see option 5, in table 21 on page 33)
99 Any remote control number
01 to 32 Remote control number
23 Button pressed on remote (see option 6, in table 21 on page 33)
99 Any remote control number
01 to 32 Zone number
24 Fire delay started
99 Any zone number

19
 SP+ Series Programming Guide

Table 10: List of events

Event Group Event Group Description Sub-group Sub-group Description

25 - - -
00 Non-valid source ID
01 BabyWare direct
02 BabyWare through IP module
03 BabyWare through PCS module
04 BabyWare through modem
26 Software access (VDMP3, IP Module, BabyWare) 09 IP Module direct
10 VDMP3 direct
11 N/A
12 Remote access
13 SMS through PCS module
99 Any software access
00 A bus module was added
01 A bus module was removed
27 Bus module event 02 2-way RF module communication failure
03 2-way RF module communication restored
99 Any bus module event
01 to 32 Zone number
28 StayD pass acknowledged
99 Any zone number
01 to 32 User number
29 Arming with user
99 Any user number
00 Auto-arming (on-time/no movement)
01 Late to close
02 No movement arming
03 Partial arming
30 Special arming
04 Quick arming
05 Arming through BabyWare
06 Arming with keyswitch
99 Any special arming
01 to 32 User number
31 Disarming with user
99 Any user number
01 to 32 User number
32 Disarming after an alarm with user
99 Any user number
01 to 32 User number
33 Alarm cancelled with user
99 Any user number
00 Auto-arm cancelled (on-time/no movement)
01 Disarming through BabyWare
02 Disarming through BabyWare after alarm
03 Alarm cancelled through BabyWare
34 Special disarming 04 Paramedical alarm cancelled
05 Disarm with keyswitch
06 Disarm with keyswitch after an alarm
07 Alarm cancelled with keyswitch
99 Any special disarming
01 to 32 Zone number
35 Zone bypassed
99 Any zone number
01 to 32 Zone number
36 Zone in alarm
99 Any zone number
01 to 32 Zone number
37 Fire alarm
99 Any zone number

20
SP+ Series Programming Guide

Table 10: List of events

Event Group Event Group Description Sub-group Sub-group Description

01 to 32 Zone number
38 Zone alarm restore
99 Any zone number
01 to 32 Zone number
39 Fire alarm restore
99 Any zone number
00 Panic non-medical emergency
01 Panic medical
02 Panic fire

40 03 Recent closing
Special alarm
04 Global shutdown
05 Duress alarm
06 Keypad lockout (partition 1 only)
99 Any special alarm event
01 to 32 Zone number
41 Zone shutdown
99 Any zone number
01 to 32 Zone number
42 Zone tampered
99 Any zone number
01 to 32 Zone number
43 Zone tamper restore
99 Any zone number

21
 SP+ Series Programming Guide

Table 10: List of events

Event Group Event Group Description Sub-group Sub-group Description

00 -
01 AC failure
02 Battery failure
03 Auxiliary current overload
04 Bell current overload
05 Bell disconnected
06 Clock loss
07 Fire loop trouble
08 Fail to communicate with monitoring station telephone # 1
09 Fail to communicate with monitoring station telephone # 2
11 Fail to communicate with voice report
New trouble (partition 1 only, except sub-group 07, which is for
44 12 RF jamming
both partitions)
13 PCS RF jamming
14 N/A
15 N/A
16 Fail to communicate IP receiver 1 (GPRS)
17 Fail to communicate IP receiver 2 (GPRS)
18 IP module no service
19 IP module supervision loss
20 Fail to communicate IP receiver 1 (IP)
21 Fail to communicate IP receiver 2 (IP)
22 GPRS module tamper trouble
99 Any new trouble event
00 Telephone line restored
01 AC failure restore
02 Battery failure restore
03 Auxiliary current overload
04 Bell current overload restore
05 Bell disconnected restore
06 Clock loss restore
07 Fire loop trouble restore
08 Fail to communicate with monitoring station tel. # 1 restore
09 Fail to communicate with monitoring station tel. # 2 restore
11 Fail to communicate with voice report restore
45 Trouble restored 12 RF jamming restore
13 PCS RF jamming restore
14 N/A
15 N/A
16 Fail to communicate restore IP receiver 1 (GPRS)
17 Fail to communicate restore IP receiver 2 (GPRS)
18 IP module no service restore
19 IP module supervision loss restore
20 Fail to communicate restore IP receiver 1 (IP)
21 Fail to communicate restore IP receiver 2 (IP)
22 GPRS module tamper trouble restore
99 Any new trouble restored event

22
SP+ Series Programming Guide

Table 10: List of events

Event Group Event Group Description Sub-group Sub-group Description

00 Bus/EBus/wireless module communication fault
01 Tamper trouble
46 Bus/EBus/wireless module new trouble (partition 1 only) 02 Power fail
03 Battery failure
99 Any bus module new trouble event
00 Bus/EBus/wireless module communication fault restore
01 Tamper trouble restore
47 Bus/EBus/wireless module trouble restored (partition 1 only) 02 Power fail restore
03 Battery failure restore
99 Any bus module new trouble restored event
00 System power up
01 Reporting test
02 Software log on
03 Software log off
04 Installer in programming mode
48 Special (partition1 only) 05 Installer exited programming mode
06 Maintenance in programming mode
07 Maintenance exited programming mode
08 Closing delinquency delay elapsed
13 Failed to arm
99 Any special event
01 to 32 Zone number
49 Low battery on zone
99 Any zone number
01 to 32 Zone number
50 Low battery on zone restore
99 Any zone number
01 to 32 Zone number
51 Zone supervision trouble
99 Any zone number
01 to 32 Zone number
52 Zone supervision restore
99 Any zone number
01 to 16 Output
17 to 18 Wireless repeater
53 Wireless module supervision trouble (partition 1 only) 19 to 22 Wireless keypad
27 to 30 Wireless siren
99 Any output number
01 to 16 Output
17 to 18 Wireless repeater
54 Wireless module supervision restore (partition 1 only) 19 to 22 Wireless keypad
27 to 30 Wireless siren
99 Any output number
01 to 16 Output
17 to 18 Wireless repeater
55 Wireless module tamper trouble (partition 1 only) 19 to 22 Wireless keypad
27 to 30 Wireless siren
99 Any output number
01 to 16 Output
17 to 18 Wireless repeater
56 Wireless module tamper restore (partition 1 only) 19 to 22 Wireless keypad
27 to 30 Wireless siren
99 Any output number

23
 SP+ Series Programming Guide

Table 10: List of events

Event Group Event Group Description Sub-group Sub-group Description

01 to 32 User number
57 Non-medical alarm (paramedic)
99 Any user number
01 to 32 Zone number
58 Zone forced
99 Any zone number

59 Zone included 01 to 32 Zone number

Zone included (Cont.) 99 Any zone number
01 to 32 User number
60 Remote low battery
99 Any user number
01 to 32 User number
61 Remote low battery restore
99 Any user number
Follow ARM LED status*:
PGM pulse fast in alarm
PGM pulse fast in exit delay, below 10 sec.
PGM pulse slow in exit delay, over 10 sec.
64 System status (on-board PGMs only) 00 PGM steady ON, if armed
PGM OFF, if disarmed
* This event can be assigned to partition 1 or 2. If assigned to
both partitions, the PGM event will follow the list order above,
with number 1 being the highest priority.

PGM Activation/Deactivation Events

Use worksheet 14 to record your settings for the SP+ Series PGM events. See table 10 on page 18, for a list of these events.

Worksheet 14: PGM Activation/Deactivation Events

Partition Partition
Section PGM Event Event Group Sub-group Default Section PGM Event Event Group Sub-group Default
(99 for both) (99 for both)
[220] Activation ___/___ ___/___ ___/___ 08/99/99* [236] Activation ___/___ ___/___ ___/___ 00/00/00
PGM 1 PGM 9
[221] Deactivation ___/___ ___/___ ___/___ 00/00/00 [237] Deactivation ___/___ ___/___ ___/___ 00/00/00
[222] Activation ___/___ ___/___ ___/___ 09/99/99** [238] Activation ___/___ ___/___ ___/___ 00/00/00
PGM 2 PGM 10
[223] Deactivation ___/___ ___/___ ___/___ 00/00/00 [239] Deactivation ___/___ ___/___ ___/___ 00/00/00
[224] Activation ___/___ ___/___ ___/___ 00/00/00 [240] Activation ___/___ ___/___ ___/___ 00/00/00
PGM 3 PGM 11
[225] Deactivation ___/___ ___/___ ___/___ 00/00/00 [241] Deactivation ___/___ ___/___ ___/___ 00/00/00
[226] Activation ___/___ ___/___ ___/___ 00/00/00 [242] Activation ___/___ ___/___ ___/___ 00/00/00
PGM 4 PGM 12
[227] Deactivation ___/___ ___/___ ___/___ 00/00/00 [243] Deactivation ___/___ ___/___ ___/___ 00/00/00
[228] Activation ___/___ ___/___ ___/___ 00/00/00 [244] Activation ___/___ ___/___ ___/___ 08/99/01
PGM 5 PGM 13
[229] Deactivation ___/___ ___/___ ___/___ 00/00/00 [245] Deactivation ___/___ ___/___ ___/___ 08/99/01
[230] Activation ___/___ ___/___ ___/___ 00/00/00 [246] Activation ___/___ ___/___ ___/___ 09/99/01
PGM 6 PGM 14
[231] Deactivation ___/___ ___/___ ___/___ 00/00/00 [247] Deactivation ___/___ ___/___ ___/___ 09/99/01
[232] Activation ___/___ ___/___ ___/___ 00/00/00 [248] Activation ___/___ ___/___ ___/___ 00/00/00
PGM 7 PGM 15
[233] Deactivation ___/___ ___/___ ___/___ 00/00/00 [249] Deactivation ___/___ ___/___ ___/___ 00/00/00
[234] Activation ___/___ ___/___ ___/___ 00/00/00 [250] Activation ___/___ ___/___ ___/___ 00/00/00
PGM 8 PGM 16
[235] Deactivation ___/___ ___/___ ___/___ 00/00/00 [251] Deactivation ___/___ ___/___ ___/___ 00/00/00
* Section [220], PGM 1 activation event: default = option B remote assignment. Button pressed on any remote/any partition (see table 21 on page 33).
** Section [222], PGM 2 activation event: default = option C remote assignment. Button pressed on any remote/any partition (see table 21 on page 33).

24
SP+ Series Programming Guide

PGM Options
Table 11: Description of PGM options

PGM 1 [261] PGM 2 [262] PGM 3 [263] PGM 4 [264] PGM 5 [265] PGM 6 [266] PGM 7 [267] PGM 8 [268]
Option Description
OFF ON OFF ON OFF ON OFF ON OFF ON OFF ON OFF ON OFF ON
1 PGM base time (OFF = sec., ON = min.)                
2 PGM state (OFF = N.O.; ON = N.C.)                

3 PGM supervision                
PGM activation mode
4                
(OFF = steady; ON = pulse)
5 PGM pulse once every 30 seconds, if armed                

6 PGM pulse on any alarm                

PGM pulse on any alarm (OFF = partition 1;

7                
ON = partition 2)
Flexible PGM deactivation option
(OFF1 = PGM delay only, two activation
8                
events; ON = PGM delay or deactivation
event, whichever comes first)
PGM 9 [269] PGM 10 [270] PGM 11 [271] PGM 12 [272] PGM 13 [273] PGM 14 [274] PGM 15 [275] PGM 16 [276]
Option Description
OFF ON OFF ON OFF ON OFF ON OFF ON OFF ON OFF ON OFF ON
1 PGM base time (OFF = sec., ON = min.)                
2 PGM state (OFF = N.O.; ON = N.C.)                

3 PGM supervision                
PGM activation mode (OFF = steady;
4                
ON = pulse)
5 PGM pulse once every 30 seconds, if armed                

6 PGM pulse on any alarm                

PGM pulse on any alarm (OFF = partition 1;

7                
ON = partition 2)
Flexible PGM deactivation option
(OFF1 = PGM delay only, two activation
8                
events; ON = PGM delay or deactivation
event, whichever comes first)

= Default Setting

1
If a PGM delay is programmed (OFF option), the deactivation event can be used as a second activation event.

Section [277] for SP5500+ / SP6000+

Table 12: Description of section [277] for SP5500+ / SP6000+

[277]
Option Option Type Description
OFF ON
1 PGM 1  
Voltage output
2 (OFF = negative trigger, 0V; PGM 2  
ON = positive trigger, 12V)
3 PGM 3  

= Default Setting

Section [277] for SP7000+

Table 13: Description of section [277] for SP7000+

[277]
Option Option Type Description
OFF ON
1 PGM 1  l

2 Voltage output PGM 2  l

(OFF = negative trigger, 0V;
3 ON = positive trigger, 12V) PGM 3  l

4 PGM 4  l

= Default Setting

25
 SP+ Series Programming Guide

PGM Delays
Use worksheet 15 to record your settings for the SP+ Series PGM delays.

Worksheet 15: PGM Delays

Section PGM PGM Delay Value Default Section PGM PGM Delay Value Default
[281] PGM 1 ___/___/___ (001 to 255 x 1 sec./min.) 015 [289] PGM 9 ___/___/___ (001 to 255 x 1 sec./min.) 015
[282] PGM 2 ___/___/___ (001 to 255 x 1 sec./min.) 015 [290] PGM 10 ___/___/___ (001 to 255 x 1 sec./min.) 015
[283] PGM 3 ___/___/___ (001 to 255 x 1 sec./min.) 015 [291] PGM 11 ___/___/___ (001 to 255 x 1 sec./min.) 015
[284] PGM 4 ___/___/___ (001 to 255 x 1 sec./min.) 015 [292] PGM 12 ___/___/___ (001 to 255 x 1 sec./min.) 015
[285] PGM 5 ___/___/___ (001 to 255 x 1 sec./min.) 015 [293] PGM 13 ___/___/___ (001 to 255 x 1 sec./min.) 015
[286] PGM 6 ___/___/___ (001 to 255 x 1 sec./min.) 015 [294] PGM 14 ___/___/___ (001 to 255 x 1 sec./min.) 015
[287] PGM 7 ___/___/___ (001 to 255 x 1 sec./min.) 015 [295] PGM 15 ___/___/___ (001 to 255 x 1 sec./min.) 015
[288] PGM 8 ___/___/___ (001 to 255 x 1 sec./min.) 015 [296] PGM 16 ___/___/___ (001 to 255 x 1 sec./min.) 015
NOTE: To change the base time (minutes or seconds), see PGM Options on page 25.

PGM Serial Numbers

Use worksheet 16 to record your settings for the SP+ PGM serial numbers. To delete a wireless PGM, enter 000000, while in the PGM’s respective section. For
automatic assignment, press the LEARN/TAMPER switch or remove and re-install Jumper 2 (JP2) on the wireless PGM, while in the PGM’s respective section.

Worksheet 16: PGM Serial Numbers

Section PGM Wireless PGM Serial Number Section PGM Wireless PGM Serial Number
[301] PGM 1 ___/___/___/___/___/___ [309] PGM 9 ___/___/___/___/___/___
[302] PGM 2 ___/___/___/___/___/___ [310] PGM 10 ___/___/___/___/___/___
[303] PGM 3 ___/___/___/___/___/___ [311] PGM 11 ___/___/___/___/___/___
[304] PGM 4 ___/___/___/___/___/___ [312] PGM 12 ___/___/___/___/___/___
[305] PGM 5 ___/___/___/___/___/___ [313] PGM 13 ___/___/___/___/___/___
[306] PGM 6 ___/___/___/___/___/___ [314] PGM 14 ___/___/___/___/___/___
[307] PGM 7 ___/___/___/___/___/___ [315] PGM 15 ___/___/___/___/___/___
[308] PGM 8 ___/___/___/___/___/___ [316] PGM 16 ___/___/___/___/___/___
NOTE: To view a PGM’s serial number, see section [960] in Description of Sections [950], [955], and [960] on page 52.

Wireless PGM Signal Strength

The signal strength for wireless PGMs is visible in sections [321] to [336]; these sections represent PGMs 1 to 16, respectively. To view the signal strength, proceed as
follows:
1. Enter the wireless PGM’s respective section (e.g., for PGM1, enter section [321]).
2. Press the LEARN/TAMPER switch or remove and re-install Jumper 2 (JP2) on the wireless PGM. As shown in table 14, the number of beeps correspond to a preset
signal strength range.
Table 14: Signal strength indicator for wireless PGMs

Number of Beeps Signal Strength Result

3 8 to 10 Strong signal
2 5 to 7 Average signal
1 1 to 4 Weak signal (relocate)

NOTE: The visual representation of a PGM’s signal strength is dependent on the type of keypad. For LED keypads, zones 1 through 10 will illuminate, depending on
the signal strength. For instance, a signal strength of 8 will result in zones 1 through 8 to illuminate. For LCD keypads, a ten-level progress bar composed of arrows
will appear, followed by the numeric value. For a signal strength of 8, eight arrows will appear, followed by the number 8.

PGM Labels
Use worksheet 17 to record your settings for the SP+ PGM labels. To reset these labels, see Description of Section [965] on page 52.
Worksheet 17: PGM Labels
Section PGM PGM Label Section PGM PGM Label
[341] PGM 1 __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__ [349] PGM 9 __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
[342] PGM 2 __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__ [350] PGM 10 __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
[343] PGM 3 __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__ [351] PGM 11 __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
[344] PGM 4 __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__ [352] PGM 12 __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
[345] PGM 5 __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__ [353] PGM 13 __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
[346] PGM 6 __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__ [354] PGM 14 __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
[347] PGM 7 __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__ [355] PGM 15 __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
[348] PGM 8 __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__ [356] PGM 16 __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
NOTE: For special characters and keypad letter assignments, see Label Programming with LCD Keypads on page 53.

26
SP+ Series Programming Guide

User Programming
Use the following section to program the various user features on your SP+ Series control panel.

System Codes
Use worksheet 18 to record your settings for the SP+ system codes. For access options, see section [701], in table 24 on page 36.
NOTE: The maintenance code cannot access the following sections: [395] (Installer code lock); [397] (Installer code); [398] (Maintenance code); [815] (Monitoring
station telephone number 1); [816] (Monitoring station telephone number 2); [817] (Backup monitoring station telephone); [910] (Panel ID); [911] (PC password);
[970] (Download memory key into panel); [975] (Upload panel into the memory key).
Worksheet 18: User System Codes
Section Data Description Default Setting
[395] ___/___/___ Installer code lock* 000
[397] ___/___/___/___/___/___ Installer code 0000
[398] ___/___/___/___/___/___ Maintenance code -
[399] ___/___/___/___/___/___ System master code 1234
* Enter 147 to lock entire control panel. Once locked, enter any other three-digit combination to unlock.

NOTE: The installer and system master codes may consist of four (default) or six digits (see option 1 of section [701], in table 24 on page 36). The control panel
automatically removes the last two digits of these codes, if the length is changed from six digits to four. However, if the access code length is changed from four
digits to six, the control panel adds the code’s first two digits to the end of the code.

User Code Options

Use worksheet 19 to record your settings for the SP+ Series user code options. See table 15 for details on these options.
Table 15: User code options

Option Description

1 Partition 1 access
2 Partition 2 access
3 Bypass programming
4 Stay/Sleep arming
5 Force arming
6 Arm only
7 PGM activation only
8 Duress

NOTE: When section [400] is accessed, the control panel will copy the saved value of that section to all user option sections ([404] to [432]).
Worksheet 19: User Code Options
Section User Options Section User Options
[400] Default option 1 2 3 4 5 6 7 8 [417] User 17 1 2 3 4 5 6 7 8
[401] System master 1 2 3 4 5 6 7 8 [418] User 18 1 2 3 4 5 6 7 8
[402] Master 1 1 2 3 4 5 6 7 8 [419] User 19 1 2 3 4 5 6 7 8
[403] Master 2 1 2 3 4 5 6 7 8 [420] User 20 1 2 3 4 5 6 7 8
[404] User 4 1 2 3 4 5 6 7 8 [421] User 21 1 2 3 4 5 6 7 8
[405] User 5 1 2 3 4 5 6 7 8 [422] User 22 1 2 3 4 5 6 7 8
[406] User 6 1 2 3 4 5 6 7 8 [423] User 23 1 2 3 4 5 6 7 8
[407] User 7 1 2 3 4 5 6 7 8 [424] User 24 1 2 3 4 5 6 7 8
[408] User 8 1 2 3 4 5 6 7 8 [425] User 25 1 2 3 4 5 6 7 8
[409] User 9 1 2 3 4 5 6 7 8 [426] User 26 1 2 3 4 5 6 7 8
[410] User 10 1 2 3 4 5 6 7 8 [427] User 27 1 2 3 4 5 6 7 8
[411] User 11 1 2 3 4 5 6 7 8 [428] User 28 1 2 3 4 5 6 7 8
[412] User 12 1 2 3 4 5 6 7 8 [429] User 29 1 2 3 4 5 6 7 8
[413] User 13 1 2 3 4 5 6 7 8 [430] User 30 1 2 3 4 5 6 7 8
[414] User 14 1 2 3 4 5 6 7 8 [431] User 31 1 2 3 4 5 6 7 8
[415] User 15 1 2 3 4 5 6 7 8 [432] User 32 1 2 3 4 5 6 7 8
[416] User 16 1 2 3 4 5 6 7 8
NOTE: The system master, master 1, and master 2 user code options cannot be modified. However, if partitioning is not enabled, the user code options for master 2
will match those of master 1.

27
 SP+ Series Programming Guide

User Report Codes

Use worksheet 20 to record your settings for the SP+ user report codes (the default code is FF). To clear and reset these codes, see Description of Sections [966] and
[967] on page 53.

Worksheet 20: User Report Codes

Section User Arming Disarming/Cancel Alarm Section User Arming Disarming/Cancel Alarm
[471] System master ____/____ ____/____ [487] User 17 ____/____ ____/____
[472] Master 1 ____/____ ____/____ [488] User 18 ____/____ ____/____
[473] Master 2 ____/____ ____/____ [489] User 19 ____/____ ____/____
[474] User 4 ____/____ ____/____ [490] User 20 ____/____ ____/____
[475] User 5 ____/____ ____/____ [491] User 21 ____/____ ____/____
[476] User 6 ____/____ ____/____ [492] User 22 ____/____ ____/____
[477] User 7 ____/____ ____/____ [493] User 23 ____/____ ____/____
[478] User 8 ____/____ ____/____ [494] User 24 ____/____ ____/____
[479] User 9 ____/____ ____/____ [495] User 25 ____/____ ____/____
[480] User 10 ____/____ ____/____ [496] User 26 ____/____ ____/____
[481] User 11 ____/____ ____/____ [497] User 27 ____/____ ____/____
[482] User 12 ____/____ ____/____ [498] User 28 ____/____ ____/____
[483] User 13 ____/____ ____/____ [499] User 29 ____/____ ____/____
[484] User 14 ____/____ ____/____ [500] User 30 ____/____ ____/____
[485] User 15 ____/____ ____/____ [501] User 31 ____/____ ____/____
[486] User 16 ____/____ ____/____ [502] User 32 ____/____ ____/____
NOTE: For instructions on formatting report codes, see Entering Report Codes on page 44.

User Labels
Use worksheet 21 to record your settings for the SP+ Series user labels. To reset these labels, see Description of Section [965] on page 52.

Worksheet 21: User Labels

Section User User Label Section User User Label
[511] 1 __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__ [527] 17 __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
[512] 2 __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__ [528] 18 __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
[513] 3 __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__ [529] 19 __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
[514] 4 __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__ [530] 20 __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
[515] 5 __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__ [531] 21 __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
[516] 6 __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__ [532] 22 __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
[517] 7 __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__ [533] 23 __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
[518] 8 __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__ [534] 24 __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
[519] 9 __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__ [535] 25 __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
[520] 10 __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__ [536] 26 __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
[521] 11 __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__ [537] 27 __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
[522] 12 __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__ [538] 28 __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
[523] 13 __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__ [539] 29 __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
[524] 14 __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__ [540] 30 __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
[525] 15 __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__ [541] 31 __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
[526] 16 __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__ [542] 32 __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
NOTE: For special characters and keypad letter assignments, see Label Programming with LCD Keypads on page 53.

28
SP+ Series Programming Guide

Wireless Repeater Programming (RPT1/RPT1+)

Use the following section to program the wireless repeaters on your SP+ Series control panel.

Wireless Repeater Assignment

Use worksheet 22 to record your settings when assigning wireless repeaters to your SP+ Series control panel. To reset wireless repeaters, see Description of Section
[965] on page 52.

Worksheet 22: Wireless Repeater Assignment

Section Description Wireless Repeater Serial Number
[545] Repeater 1 ___/___/___/___/___/___
[546] Repeater 2 ___/___/___/___/___/___
NOTE: For automatic assignment, press the wireless repeater’s anti-tamper switch, while in the repeater’s respective section.

Wireless Repeater Signal Strength

The signal strength for wireless repeaters is visible in sections [548] and [549]; these sections represent repeaters 1 and 2, respectively. To view the signal strength,
proceed as follows:
1. Enter the wireless repeater’s respective section (e.g., for repeater 1, enter section [548]).
2. Press the repeater’s anti-tamper switch. As shown in table 16, the number of beeps correspond to a preset signal strength range.
Table 16: Signal strength indicator for wireless repeaters

Number of Beeps Signal Strength Result

3 8 to 10 Strong signal
2 5 to 7 Average signal
1 1 to 4 Weak signal (relocate)
NOTE: The visual representation of a repeater’s signal strength is dependent on the type of keypad. For LED keypads, zones 1 through 10 will illuminate, depending
on the signal strength. For instance, a signal strength of 8 will result in zones 1 through 8 to illuminate. For LCD keypads, a ten-level progress bar composed of
arrows will appear, followed by the numeric value. For a signal strength of 8, eight arrows will appear, followed by the number 8.

29
 Wireless Repeater Options
30

Table 17: Description of the wireless repeater options

RPT1/ RPT1 /
RPT2 [561] RPT2 [564] RPT1 [557] RPT2 [567]
Option Description RPT1+ [551] Option Description RPT1+ [554] Option Description
OFF ON OFF ON OFF ON OFF ON OFF ON OFF ON
1 Repeat wireless keypad 1 signals     1 Repeat wireless zone 17 signals     1 Repeat wireless two-way PGM 9 signals    

2 Repeat wireless keypad 2 signals     2 Repeat wireless zone 18 signals     2 Repeat wireless two-way PGM 10 signals    

3 Repeat wireless keypad 3 signals     3 Repeat wireless zone 19 signals     3 Repeat wireless two-way PGM 11 signals    

4 Repeat wireless keypad 4 signals     4 Repeat wireless zone 20 signals     4 Repeat wireless two-way PGM 12 signals    

5 Repeat wireless keypad 5 signals     5 Repeat wireless zone 21 signals     5 Repeat wireless two-way PGM 13 signals    

6 Repeat wireless keypad 6 signals     6 Repeat wireless zone 22 signals     6 Repeat wireless two-way PGM 14 signals    

7 Repeat wireless keypad 7 signals     7 Repeat wireless zone 23 signals     7 Repeat wireless two-way PGM 15 signals    

8 Repeat wireless keypad 8 signals     8 Repeat wireless zone 24 signals     8 Repeat wireless two-way PGM 16 signals    

RPT1/ RPT1 /
RPT2 [562] RPT2 [565] = Default Setting
Option Description RPT1+ [552] Option Description RPT1+ [555]
OFF ON OFF ON OFF ON OFF ON
1 Repeat wireless zone 1 signals     1 Repeat wireless zone 25 signals    

2 Repeat wireless zone 2 signals     2 Repeat wireless zone 26 signals    

3 Repeat wireless zone 3 signals     3 Repeat wireless zone 27 signals    

4 Repeat wireless zone 4 signals     4 Repeat wireless zone 28 signals    

5 Repeat wireless zone 5 signals     5 Repeat wireless zone 29 signals    

6 Repeat wireless zone 6 signals     6 Repeat wireless zone 30 signals    

7 Repeat wireless zone 7 signals     7 Repeat wireless zone 31 signals    

8 Repeat wireless zone 8 signals     8 Repeat wireless zone 32 signals    

RPT1/ RPT1/
RPT2 [563] RPT2 [566]
Option Description RPT1+ [553] Option Description RPT1+ [556]
OFF ON OFF ON OFF ON OFF ON
1 Repeat wireless zone 9 signals     1 Repeat wireless two-way PGM 1 signals    

2 Repeat wireless zone 10 signals     2 Repeat wireless two-way PGM 2 signals    

3 Repeat wireless zone 11 signals     3 Repeat wireless two-way PGM 3 signals    

4 Repeat wireless zone 12 signals     4 Repeat wireless two-way PGM 4 signals    

5 Repeat wireless zone 13 signals     5 Repeat wireless two-way PGM 5 signals    

6 Repeat wireless zone 14 signals     6 Repeat wireless two-way PGM 6 signals    

7 Repeat wireless zone 15 signals     7 Repeat wireless two-way PGM 7 signals    

8 Repeat wireless zone 16 signals     8 Repeat wireless two-way PGM 8 signals    

 Wireless Repeater Labels
Use worksheet 23 to record your settings for wireless repeater labels. To reset these labels, see Description of Section [965] on page 52.

Worksheet 23: Wireless Repeater Labels

Section Description Wireless Repeater Label
[568] Repeater 1 __/__/__/__/__/__/__/__/__/__/__/__/__/__/__
[569] Repeater 2 __/__/__/__/__/__/__/__/__/__/__/__/__/__/__
NOTE: For special characters and keypad letter assignments, see Label Programming with LCD Keypads on page 53.

Wireless Keypad Programming

Automatic Wireless Keypad Assignment
After powering-up, the control panel will open a ten-minute window for automatic assignment. To assign a keypad to your SP+ Series control panel, press and hold and BYP for three seconds on the respective
keypad. Up to eight wireless keypads can be assigned within this ten-minute period.

Compatibility Check (K37 only)

If the K37 is not compatible with the current SP+ Series control panel version, the following trouble will be displayed: [TROUBLE: FLASH] [17: ON]. If this occurs, update your SP+ Series control panel to version 3.2 or
higher.

Standard Wireless Keypad Assignment

Use worksheet 24 to record your settings, when assigning wireless keypads to your SP+ Series control panel. To assign your wireless keypads, enter the serial number or press and hold and BYP for three seconds.

Worksheet 24: Wireless Keypad Assignment

Section Description Wireless Keypad Serial Number
[571] Keypad 1 ___/___/___/___/___/___
[572] Keypad 2 ___/___/___/___/___/___
[573] Keypad 3 ___/___/___/___/___/___
[574] Keypad 4 ___/___/___/___/___/___
[575] Keypad 5 ___/___/___/___/___/___
[576] Keypad 6 ___/___/___/___/___/___
[577] Keypad 7 ___/___/___/___/___/___
[578] Keypad 8 ___/___/___/___/___/___

Wireless Keypad, Repeater, and Siren Options

Table 18: Description of section [587]

[587] [587]
Option Description Option Description
OFF ON OFF ON
1 Repeater 1 supervision   5 Wireless siren 3 supervision  
2 Repeater 2 supervision   6 Wireless siren 4 supervision  
3 Wireless siren 1 supervision   8 Live display mode  
4 Wireless siren 2 supervision   = Default

NOTE: To cancel the wireless siren tamper supervision, see Cancelling the Tamper Supervision for Wireless Sirens on page 36.
31
 SP+ Series Programming Guide

Wireless Keypad Options

Table 19: Description of section [588]

[588] [588]
Option Description Option Description
OFF ON OFF ON
1 Keypad 1 supervision   5 Keypad 5 supervision  
2 Keypad 2 supervision   6 Keypad 6 supervision  
3 Keypad 3 supervision   7 Keypad 7 supervision  
4 Keypad 4 supervision   8 Keypad 8 supervision  
= Default

32
SP+ Series Programming Guide

Wireless Keypad Signal Strength

The signal strength for wireless keypads is visible in sections [591] to [598]; these sections represent keypads 1 through 8, respectively. To view the signal strength,
proceed as follows:
1. Enter the wireless keypad’s respective section (e.g., for keypad 1, enter section [591]).
2. Press on the keypad. As shown in table 20, the number of beeps correspond to a preset signal strength range.
Table 20: Signal strength indicator for wireless keypads

Number of Beeps Signal Strength Result

3 8 to 10 Strong signal
2 5 to 7 Average signal
1 1 to 4 Weak signal (relocate)

NOTE: The visual representation of a keypad’s signal strength is dependent on the type of keypad. For LED keypads, zones 1 through 10 will illuminate, depending
on the signal strength. For instance, a signal strength of 8 will result in zones 1 through 8 to illuminate. For LCD keypads, a ten-level progress bar composed of
arrows will appear, followed by the numeric value. For a signal strength of 8, eight arrows will appear, followed by the number 8.

Wireless Keypad Labels

Use worksheet 25 to record your settings for wireless keypad labels. To reset these labels, see Description of Section [965] on page 52.

Worksheet 25: Wireless Keypad Labels

Section Description Wireless Keypad Label
[599] Keypad 1 __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
[600] Keypad 2 __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
[601] Keypad 3 __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
[602] Keypad 4 __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
[603] Keypad 5 __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
[604] Keypad 6 __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
[605] Keypad 7 __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
[606] Keypad 8 __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
NOTE: For special characters and keypad letter assignments, see Label Programming with LCD Keypads on page 53.

Remote Control Programming

Use the following section to program remote controls for your SP+ control panel.

Remote Control Button Assignment

Use worksheet 26 on page 34 to record your settings when assigning remote controls to your SP+ Series control panel. See table 21 for details on button options for
these remotes.
NOTE: Remote controls which are supported by SP+ Series control panels are the following: REM1, REM2, RAC1, RAC2, REM3, and REM15.
Table 21: Button options for SP+ remote controls (see Decimal and Hexadecimal Programming on page 4)

Option Description Option Description

Sleep Empty/button disabled 8 Panic 1
1 Regular/regular force arming 9 Panic 2
2 Stay/stay force arming A Panic 3
3 - B PGM activation (event group 8)*
4 Sleep/sleep force arming C PGM activation (event group 9)*
5 PGM activation (event group 22)* D PGM activation (event group 10)*
6 PGM activation (event group 23)* E PGM activation (event group 11)*
7 Activate window mode (StayD) F Paramedic alarm
* For descriptions on the event groups, see Description of Events on page 18.

NOTE: The disarm button ( ) cannot be modified.

33
34

Worksheet 26: Programming Remote Controls

REM3 Remote Control REM1/REM2/RAC1/RAC2/REM15

PGM 1 PGM 2 PGM 3 PGM 4 PGM 5 PGM 6 PGM 3 & 4 PGM 5 & 6 +
9 0  X+ +
X
+
Default Data B C D E 5 6 Disabled Disabled Default Data 1 B C Disabled
RC # Section RC # Section
All [610] _____ _____ _____ _____ _____ _____ _____ _____ All [610] _____ _____ _____ _____
1 [611] _____ _____ _____ _____ _____ _____ _____ _____ 1 [611] _____ _____ _____ _____
2 [612] _____ _____ _____ _____ _____ _____ _____ _____ 2 [612] _____ _____ _____ _____
3 [613] _____ _____ _____ _____ _____ _____ _____ _____ 3 [613] _____ _____ _____ _____
4 [614] _____ _____ _____ _____ _____ _____ _____ _____ 4 [614] _____ _____ _____ _____
5 [615] _____ _____ _____ _____ _____ _____ _____ _____ 5 [615] _____ _____ _____ _____
6 [616] _____ _____ _____ _____ _____ _____ _____ _____ 6 [616] _____ _____ _____ _____
7 [617] _____ _____ _____ _____ _____ _____ _____ _____ 7 [617] _____ _____ _____ _____
8 [618] _____ _____ _____ _____ _____ _____ _____ _____ 8 [618] _____ _____ _____ _____
9 [619] _____ _____ _____ _____ _____ _____ _____ _____ 9 [619] _____ _____ _____ _____
10 [620] _____ _____ _____ _____ _____ _____ _____ _____ 10 [620] _____ _____ _____ _____
11 [621] _____ _____ _____ _____ _____ _____ _____ _____ 11 [621] _____ _____ _____ _____
12 [622] _____ _____ _____ _____ _____ _____ _____ _____ 12 [622] _____ _____ _____ _____
13 [623] _____ _____ _____ _____ _____ _____ _____ _____ 13 [623] _____ _____ _____ _____
14 [624] _____ _____ _____ _____ _____ _____ _____ _____ 14 [624] _____ _____ _____ _____
15 [625] _____ _____ _____ _____ _____ _____ _____ _____ 15 [625] _____ _____ _____ _____
16 [626] _____ _____ _____ _____ _____ _____ _____ _____ 16 [626] _____ _____ _____ _____
17 [627] _____ _____ _____ _____ _____ _____ _____ _____ 17 [627] _____ _____ _____ _____
18 [628] _____ _____ _____ _____ _____ _____ _____ _____ 18 [628] _____ _____ _____ _____
19 [629] _____ _____ _____ _____ _____ _____ _____ _____ 19 [629] _____ _____ _____ _____
20 [630] _____ _____ _____ _____ _____ _____ _____ _____ 20 [630] _____ _____ _____ _____
21 [631] _____ _____ _____ _____ _____ _____ _____ _____ 21 [631] _____ _____ _____ _____
22 [632] _____ _____ _____ _____ _____ _____ _____ _____ 22 [632] _____ _____ _____ _____
23 [633] _____ _____ _____ _____ _____ _____ _____ _____ 23 [633] _____ _____ _____ _____
24 [634] _____ _____ _____ _____ _____ _____ _____ _____ 24 [634] _____ _____ _____ _____
25 [635] _____ _____ _____ _____ _____ _____ _____ _____ 25 [635] _____ _____ _____ _____
26 [636] _____ _____ _____ _____ _____ _____ _____ _____ 26 [636] _____ _____ _____ _____
27 [637] _____ _____ _____ _____ _____ _____ _____ _____ 27 [637] _____ _____ _____ _____
28 [638] _____ _____ _____ _____ _____ _____ _____ _____ 28 [638] _____ _____ _____ _____
29 [639] _____ _____ _____ _____ _____ _____ _____ _____ 29 [639] _____ _____ _____ _____
30 [640] _____ _____ _____ _____ _____ _____ _____ _____ 30 [640] _____ _____ _____ _____
31 [641] _____ _____ _____ _____ _____ _____ _____ _____ 31 [641] _____ _____ _____ _____
32 [642] _____ _____ _____ _____ _____ _____ _____ _____ 32 [642] _____ _____ _____ _____
NOTE: When section [610] is accessed, the control panel will copy the saved value of that section to all remote controls.
Important: When using an RTX3 with the SP+ Series, the left button on a remote control will, by default, trigger PGM3 on the RTX3.
SP+ Series Programming Guide

User Assignment for Remote Controls

Table 22: User assignment per remote control

Section Description Section Description Section Description Section Description

[651] RC 1 for user 1 [659] RC 9 for user 9 [667] RC 17 for user 17 [675] RC 25 for user 25

[652] RC 2 for user 2 [660] RC 10 for user 10 [668] RC 18 for user 18 [676] RC 26 for user 26

[653] RC 3 for user 3 [661] RC 11 for user 11 [669] RC 19 for user 19 [677] RC 27 for user 27

[654] RC 4 for user 4 [662] RC 12 for user 12 [670] RC 20 for user 20 [678] RC 28 for user 28

[655] RC 5 for user 5 [663] RC 13 for user 13 [671] RC 21 for user 21 [679] RC 29 for user 29

[656] RC 6 for user 6 [664] RC 14 for user 14 [672] RC 22 for user 22 [680] RC 30 for user 30

[657] RC 7 for user 7 [665] RC 15 for user 15 [673] RC 23 for user 23 [681] RC 31 for user 31

[658] RC 8 for user 8 [666] RC 16 for user 16 [674] RC 24 for user 24 [682] RC 32 for user 32

Assigning a Remote Control

1. Enter the remote’s respective section (see table 22).
2. Press any button on the designated remote twice, or manually enter the serial number.
Deleting a Remote Control
1. Enter the remote’s respective section (see table 22).
2. Enter 000000.
NOTE: To view a remote control’s serial number, see section [960] in Description of Sections [950], [955], and [960] on page 52.

Wireless Siren Programming

Use the following section to program wireless sirens for your SP+ control panel.

Wireless Siren Assignment

Use worksheet 27 to record your settings when assigning wireless sirens.

Worksheet 27: Wireless Siren Assignment

Section Description Wireless Siren Serial Number Section Description Wireless Siren Serial Number
[683] Siren 1 ___/___/___/___/___/___ [685] Siren 3 ___/___/___/___/___/___
[684] Siren 2 ___/___/___/___/___/___ [686] Siren 4 ___/___/___/___/___/___

Wireless Siren Signal Strength

The signal strength for wireless keypads is visible in sections [687] to [690]; these sections represent sirens 1 through 4, respectively. To view the signal strength:
1. Enter the wireless siren’s respective section (e.g., for siren 1, enter section [687]).
2. Note the number of beeps which are emitted. As shown in table 20, the number of beeps correspond to a preset signal strength range.
Table 23: Signal strength indicator for wireless sirens

Number of Beeps Signal Strength Result

3 8 to 10 Strong signal
2 5 to 7 Average signal
1 1 to 4 Weak signal (relocate)

NOTE: The visual representation of a siren’s signal strength is dependent on the type of keypad. For LED keypads, zones 1 through 10 will illuminate, depending on
the signal strength. For instance, a signal strength of 8 will result in zones 1 through 8 to illuminate. For LCD keypads, a ten-level progress bar composed of arrows
will appear, followed by the numeric value. For a signal strength of 8, eight arrows will appear, followed by the number 8.

Wireless Siren Labels

Use worksheet 28 to record your settings for wireless siren labels. To reset these labels, see Description of Section [965] on page 52.

Worksheet 28: Wireless Siren Labels

Section Description Wireless Siren Label Section Description Wireless Siren Label
[691] Siren 1 __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__ [693] Siren 3 __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
[692] Siren 2 __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__ [694] Siren 4 __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
NOTE: For special characters and keypad letter assignments, see Label Programming with LCD Keypads on page 53.

35
 Cancelling the Tamper Supervision for Wireless Sirens
36

To cancel tamper supervision, access section [695], and then press ENTER. The tamper supervision is disabled until the cover is replaced or after 30 minutes have elapsed.

Description of Sections [700] to [704]

The following section provides information on sections [700] to [704]. See table 24 for details. For keypad programming instructions, refer to on page 7.
Table 24: Description of sections [700] to [704]

Option Option Type Description OFF ON Option Option Type Description OFF ON

1 Partitioning Partitioning  Disabled  Enabled 1 Access/master code Access code length*  6 digits  4 digits

2 Future Use - - - - 2 options Lock master code  Disabled  Enabled

Audible trouble warning (except AC
3  Disabled  Enabled 3 Confidential mode  Disabled  Enabled
General system options failure)
Section [700]

Section [701]
 Keypad options 1**
4 Audible trouble warning on AC failure Disabled  Enabled 4 To exit confidential mode  Enter code  Press a key

5 RF jamming supervision RF jamming supervision  Disabled  Enabled 5 Confidential mode timer  2 mins.  5 secs.
V2.01 or
6 Exit delay termination  Disabled  Enabled 6 REM2 version number REM2 version number  V2.00 
General system options higher
7 Tamper supervision on the bus module  Disabled  Enabled 7 Display entry delay on LCD keypad  Disabled  Enabled
Keypad options 1
8 Future Use - - - - - 8 Display exit delay on LCD keypad  Disabled  Enabled

1 Panic 1  Disabled  Enabled 1 One-touch regular arming (also REM3)  Disabled  Enabled

2 Panic 2  Disabled  Enabled 2 One-touch stay arming (also REM3)  Disabled  Enabled
Keypad options 2
3 Panic 3  Disabled  Enabled 3 One-touch sleep arming (also REM3)  Disabled  Enabled
Section [702]

Section [703]
4 Panic options Panic 1: report only or audible alarm  Report only  Audible 4 One-touch bypass programming  Disabled  Enabled

5 Panic 2: report only or audible alarm  Report only  Audible 5 Restrict arming on battery failure  Disabled  Enabled
Restrict arming on tamper failure (zone
6 Panic 3: report only or audible alarm  Report only  Audible 6 Arming/disarming options + bus module + wireless PGM)  Disabled  Enabled

Restrict arming on supervision trouble;

7 Future use - - - - - 7  Disabled  Enabled
wireless zones & PGM + bus module
8 Future use - - - - - 8 Future Use - - - - -
Regular arming switches to force
1  Disabled  Enabled = Default
arming
*All numbers from 000000 to 999999 are valid giving a total o f 1,000,000 different possible combinations.
Stay arming switches to stay force
2  Disabled  Enabled **Automatic timed operation that will make indications inaccessible to users without a valid access code.
arming
Arming/disarming options
Sleep arming switches to sleep force
3  Disabled  Enabled
arming
Section [704]

Bell squawk when arm/disarm with

4  Disabled  Enabled
remote
Bell squawk when arm/disarm with a
5  Disabled  Enabled
keypad
6 Keypad options 3 Beep on exit delay  Disabled  Enabled
No exit delay beeps and no bell
7  Disabled  Enabled
squawk, when stay/sleep arm
8 Arming/disarming options No exit delay when arm with remote  Disabled  Enabled
SP+ Series Programming Guide

Zone Options
Use the following section to program zone options for your SP+ Series control panel.

ATZ, Zone Tamper, and Supervision Options

Table 25: Description of section [705]

Option Description OFF ON

1 ATZ zone doubling  Disabled  Enabled
2 ATZ wiring options  Series  Parallel
Section [705]

3
Tamper recognition (see table 26 for details)
4
5 Generate tamper on bypassed zone  No  Yes
6
Supervision options (see table 26 for details)
7
8 Generate supervision on bypassed zone  No  Yes

= Default
NOTE: ATZ is only available for the SP6000+.

Table 26: Description of options 3 & 4 and 6 & 7, in section [705]

Option Description
3 4 RF Zone/Hardwired Zone Tamper Recognition Options Keypad/Bus Module Tamper Recognition Options*
OFF OFF Disabled Disabled
OFF ON Trouble only Trouble only
ON OFF When disarmed: trouble only; when armed: follow zone’s alarm type Trouble only
ON ON When disarmed: audible alarm; when armed: follow zone’s alarm type Audible alarm
6 7 RF Zone Supervision Options Keypad/Bus Module Supervision Options
OFF OFF Disabled Disabled
OFF ON Trouble only Trouble only
ON OFF When disarmed: trouble only; when armed: follow zone’s alarm type Trouble only
ON ON When disarmed: audible alarm; when armed: follow zone’s alarm type Audible alarm

* Tamper recognition of keypad/bus module, only if section [700], option 7, is enabled.

General Zone Options

Table 27: Description of section [706]

Option Description OFF ON

1 Check-in supervision time  24 hours  80 minutes

Section [706]

2 EOL resistors (applies to all hardwired zones – panel, keypad, ZX8/ZX82) Disabled  Enabled
3 Zone input 1 becomes a two-wire smoke input  Disabled  Enabled
4 ZX8/ZX82 ID A (panel + 1) input 1  Zone input  Tamper input
5 ZX8/ZX82 ID B (panel + 9) input 1  Zone input  Tamper input
6 ZX8/ZX82 ID C (panel + 17) input 1  Zone input  Tamper input

= Default

37
 SP+ Series Programming Guide

Miscellaneous System Options

Table 28: Description of section [708]

Option Description OFF ON

1 Enter code to view trouble  One-touch  Enter code
EN50131 OPTIONS


Section [708]

2 Enter code to view alarm in memory/event list One-touch  Enter code

3 Trouble latch  Disabled  Enabled
4 Bell squawk on Installer in  Disabled  Enabled
5 Acknowledge trouble(s) before arming  Disabled  Enabled
6 Do not arm if zone opens during exit delay  Disabled  Enabled
7 Disable ‘Bypass and Arm’  Disabled  Enabled

8 Future use

= Default

Unlock Panel Serial Ports

Enter section [300] to unlock your SP+’s panel serial ports for use with third-party devices using a TM70/TM50 Touch keypad and the K32LCD+. For a step-by-step
procedure, refer to the Insite Gold Installer Menu Guide.

System Timers
Use the following section to program system timers on your SP+ Series control panel. Use worksheet 29 to record your settings.

Worksheet 29: System Timers

Section Data Description Section Data Description
Remote panic disarm lock delay
[710] ___/___/___ 000 to 255 seconds Entry delay 1* (default: 045) [718] ___/___/___ 000 to 255 seconds (default: 000)
Closing delinquency delay
[711] ___/___/___ 000 to 255 seconds Entry delay 2* (default: 045) [719] ___/___/___ 000 to 255 days (default: 000)
Auto-zone shutdown counter
[712] ___/___/___ 000 to 015 (default: 005) [720] ___/___/___ 000 to 255 seconds Flex-instant delay (default: 015)
For StayD: re-arm delay
[713] ___/___/___ 000 to 255 seconds Intellizone delay (default: 048) [721] ___/___/___ 000 to 255 seconds (default: 005)
Auto trouble shutdown**
[714] ___/___/___ 000 to 255 minutes Recycle alarm delay (default: 000) [722] ___/___/___ 000 to 255 times (default:000)
Recycle alarm counter Panic shutdown**
[715] ___/___/___ 000 to 255 (default: 000) [723] ___/___/___ 000 to 255 seconds (default:000)
* For EN 50131, the maximum value is 45 seconds.
** For EN 50131, the section must be set to a minimum of 3 and a maximum of 10

Keypad Lockout
Use the following section to program keypad lockout settings for your SP+ Series control panel. Use worksheet 30 to record your settings.

Worksheet 30: Keypad Lockout

Section Data Description Default
[716] ___/___/___ 000 to 255 minutes Keypad lockout delay 000
[717] ___/___/___ 000 to 255 attempts before locking Keypad lockout counter 000
NOTE: For EN 50131, the keypad lockout value must be set between three and ten attempts. The minimum delay to lock must be two minutes.

Programming the Daylight Savings Feature

Use the following section to program Daylight Savings Time on your SP+ Series control panel. Use worksheet 31 to record your settings.
Table 29: Description of section [730]

Section Option Description OFF ON

[730] 1 Daylight savings  Disabled  Enabled

= Default

38
SP+ Series Programming Guide

Country Codes
Table 30 lists countries and their respective codes. This information is required when programming section [731] (see worksheet 31 for details).
Table 30: Country codes for SP+ control panels

Input Value Country Input Value Country

00 Mexico; St. Johns; Bahamas; Turks and Caicos 10 Chatham
01 Cuba 11 Tonga
02 Brazil 12 Iraq; Syria
03 Chile 13 Israel
04 Falkland Islands 14 Lebanon; Kyrgyzstan
05 Paraguay 15 Palestine
06 European Union; United Kingdom; Greenland 16 Egypt
07 Russia and surrounding countries 17 Namibia
South Australia; Victoria; Australian Capital Territory; New
08 18 Canada; United States
South Wales
09 Tasmania; Lord Howe Island 19 New Zealand

Customized Daylight Savings Features

In addition to using the default Daylight Saving Time (DST) settings in section [731], you can also set a customized DST. In sections [732] and [733], you can
program DST starting and ending periods, respectively. Both these sections recognize five different entries, consisting of two digits each.
All entries must be made in the following order:
1. Month: 01 to 12, where 01 represents January
2. Date: 01 to 31, where 01 represents the first day of the month
3. Day: 00 to 07, where 00 is the default setting and 01 represents Sunday
4. Hours: 00 to 23, where 00 represents 12:00 AM
5. Minutes: 00 only, where 00 represents the top of the hour (e.g., 12:00 AM)
NOTE: If the Day value is set to 00, it is ignored and the DST change will only respect the Date value. If the Day setting is set to a value other than 00 (e.g., 03 for
Tuesday), the DST time change will occur on the first Tuesday following the programmed Date value.
Worksheet 31: Daylight Savings Time
Section Data Description
[731] ___/___ 00 to 99 Country code
[732] __/__/__/__/__/__/__/__/__/__ Month-date-day-hours-minutes DST staring period
[733] __/__/__/__/__/__/__/__/__/__ Month-date-day-hours-minutes DST ending period
NOTE: If sections [732] and [733] have been modified, but you want to revert to a standard DST code, change all settings in sections [732] and [733] to 00.

Partition Programming
Use the following section to program partitions on your SP+ Series control panel.

Partition Options
Table 31: Description of partition 1 options (section [741])

Option Description OFF ON Option

Description
1 Auto-arm on time  Disabled  Enabled 3 4
2 Auto-arm on no movement  Disabled  Enabled OFF OFF Regular (default)
Section [741]

See options 3 See options 3

3&4 Auto-arm arming mode   OFF ON Sleep
& 4, on right & 4, on right
5 Switch to stay arming, if no entry zone is opened  Disabled  Enabled ON OFF Stay
Follow zones become entry delay 2, when delay
6  Disabled  Enabled
zone is bypassed

= Default

39
 SP+ Series Programming Guide

Table 32: Description of partition 2 options (section [742])

Option Description OFF ON Option

Description
1 Auto-arm on time  Disabled  Enabled 3 4
2 Auto-arm on no movement  Disabled  Enabled OFF OFF Regular (default)
Section [742]

See options 3 See options 3

3&4 Auto-arm arming mode   OFF ON Sleep
& 4, on right & 4, on right
5 Switch to stay arming, if no entry zone is opened  Disabled  Enabled ON OFF Stay
Follow zones become entry delay 2, when delay
6  Disabled  Enabled
zone is bypassed

= Default

Partition Timers
Use worksheet 32 to record your settings for partition timers.

Worksheet 32: Partition Timers

Section Data Description Default
[745] ___/___/___ 000 to 255 seconds Partition 1 exit delay 060
[746] ___/___/___ 000 to 255 seconds Partition 2 exit delay 060
[747] ___/___/___ 000 to 255 minutes Partition 1 bell cut-off 004*
[748] ___/___/___ 000 to 255 minutes Partition 2 bell cut-off 004*
[749] ___/___/___ 000 to 255 x 15 minutes Partition 1 no movement 000
[750] ___/___/___ 000 to 255 x 15 minutes Partition 2 no movement 000
[761] ___/___ : ___/___ HH:MM Auto-arm on time partition 1 00:00
[762] ___/___ : ___/___ HH:MM Auto-arm on time partition 2 00:00
*For EN 50131, the minimum bell cut-off timer value should be 2 minutes and maximum 60 minutes.

Partition Labels
Use worksheet 33 to record your settings for partition labels. To reset these labels, see Description of Section [965] on page 52.

Worksheet 33: Partition Labels

Section Description Partition Label
[771] Partition 1 __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
[772] Partition 2 __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
NOTE: For special characters and keypad letter assignments, see Label Programming with LCD Keypads on page 53.

SMS and Bus Module Programming

Use the following section to program SMS site name and bus module labels on your SP+ Series control panel.

SMS Site Name

Use worksheet 34 to record your SMS site name. See worksheet 50 on page 51, for additional communication settings.

Worksheet 34: SMS Site Name

Section Description Name
[780] SMS site name __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__

Bus Module Labels

Use worksheet 35 to record your settings for bus module labels. To reset these labels, see Description of Section [965] on page 52.

Worksheet 35: Bus Module Labels

Section Description Bus Module Label Section Description Bus Module Label
[781] Bus 1 __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__ [789] Bus 9 __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
[782] Bus 2 __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__ [790] Bus 10 __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
[783] Bus 3 __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__ [791] Bus 11 __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
[784] Bus 4 __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__ [792] Bus 12 __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
[785] Bus 5 __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__ [793] Bus 13 __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
[786] Bus 6 __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__ [794] Bus 14 __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
[787] Bus 7 __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__ [795] Bus 15 __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
[788] Bus 8 __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
NOTE: For special characters and keypad letter assignments, see Label Programming with LCD Keypads on page 53.

40
SP+ Series Programming Guide

Communication Programming
Use the following section to program various communication features on your SP+ Series control panel. Table 33 lists features available for each
SP+ Series control panel.
Prioritization of signals and messages are based on a “first in, first out” scheme. Systems meet EN 50136 ATS2 or ATS3 requirements when configured as depicted.
NOTE: For increased security, it is suggested that redundant communication methods be installed.
Table 33: Communication features for SP+ Series panels

Control Panel
Communication Feature
SP5500+ SP6000+ SP7000+
GPRS reporting (PCS series)   
SMS (PCS series)   
IP reporting (IP Module)   
E-mail/monitoring (IP Module)   
Patented dialer   

Dialer Options
Table 34: Description of dialer options for landline communication (section [800])

Option Description OFF ON

See options 1 See options 1 Option
1&2 Telephone line monitoring   Description
& 2, on right & 2, on right
3 Switch to pulse on fifth attempt  Disabled  Enabled 1 2
Section [800]

4 Alternate dial  Disabled  Enabled OFF OFF Disabled (default)

5 Force dial (must be enabled to comply with TBR-21)  Disabled  Enabled OFF ON Trouble only
When disarmed: trouble only; when
6 DTMF dialing  Disabled  Enabled ON OFF
armed: audible only
7 Pulse ratio  1:2  1:1.5 ON ON Silent alarms become audible alarm

8 Reporting* 
Dialer
 No dialer = Default
activated

* This option also applies to landline.

Table 35: Description of general communication dialer options (section [801])

Option Description OFF ON

1 Report system disarming  Always  After alarm
2 Report zone restore  Bell cutoff  Zone closure
Section [801]

3&4 Auto-test report transmission  See table 36 on page 41  See table 36 on page 41
CID defaults/slow format
5 Contact ID override  Disabled 
custom
6 Future Use - - - -
7 Future Use - - - -
8 Future Use - - - -

= Default

Table 36: Auto-test report transmission options (section [801])

Option
Description
3 4
Transmit the test report code when the days programmed in section [840] have elapsed, at the time programmed in section
1 OFF OFF
[850] (default).
When disarmed: transmit test report code when the time programmed in section [852] has elapsed. When armed: transmit test
2 OFF ON
report code when the time programmed in section [851] has elapsed.
The control panel will transmit the test report code every hour, on the minute value programmed in section [850] (the last two
3 ON OFF digits); the first two digits of section [850] will be ignored. For example, if 10:25 was programmed into section [850], the test
report code would be transmitted at the 25th minute of every hour, i.e., 11:25, 12:25, etc.
The test report code will be transmitted when the conditions in entries 2 or 3 above (option 3 = OFF and option 4 = ON; option 3
4 ON ON
= ON and option 4 = OFF), are met.

41
 SP+ Series Programming Guide

Event Call Direction Options

Table 37: Description of event call direction options (sections [802] to [804])

Option Description OFF ON Option Description OFF ON

Call tel. #1/monitoring rcvr. #1 for Call tel. #1/monitoring rcvr. #1 for
 
Event Call Direction Options 1

Event Call Direction Options 2

1  Disabled Enabled 1  Disabled Enabled
arm/disarm report codes tamper/restore report codes
Call tel. #2/monitoring rcvr. #2 for Call tel. #2/monitoring rcvr. #2 for
2  Disabled  Enabled 2  Disabled  Enabled
arm/disarm report codes tamper/restore report codes
Section [802]

Section [803]
3 N/A 3 N/A
Call tel. #1/monitoring rcvr. #1 for Call tel. #1/monitoring rcvr. #1 for
5  Disabled  Enabled 5  Disabled  Enabled
alarm/restore report codes trouble/restore report codes
Call tel. #2/monitoring rcvr. #2 for Call tel. #2/monitoring rcvr. #2 for
6  Disabled  Enabled 6  Disabled  Enabled
alarm/restore report codes trouble/restore report codes
7 N/A 7 N/A

1
Call tel. #1/monitoring rcvr. #1 for
 Disabled  Enabled = Default
special report codes
Event Call Direction Options 3

Call tel. #2/monitoring rcvr. #2 for

2  Disabled  Enabled
special report codes
Section [804]

3 N/A
Call personal tel. # on zone alarm
5  Disabled  Enabled
(burglary/fire)
6 Call personal tel. # on panic alarms  Disabled  Enabled
Call personal tel. # on paramedic
7  Disabled  Enabled
alarms
Call personal tel. # on panel power
8  Disabled  Enabled
trouble

IP/GPRS Options
Table 38: Description of IP/GPRS options (section [806])

Option Description OFF ON Option

Description
5&6 IP no service trouble feedback  See options 5 & 6  See options 5 & 6 5 6
Enabled
As backup for IP/
Section [806]

7 User dialer reporting   In addition to IP OFF OFF Disabled

GPRS reporting
reporting
8 Enable IP/GPRS reporting  Disabled  Enabled OFF ON Trouble only

= Default ON OFF
When disarmed: trouble only; when
armed: audible alarm
ON ON Silent alarm becomes audible alarm

42
SP+ Series Programming Guide

Report Codes and Partition Accounts

Use worksheet 36 to record your settings for sections [810] to [812].

Worksheet 36: Report Codes and Partition Accounts

Section Data Description
Tel. 1 & Tel. 2; Reporting format:
[810] ___/___ 0 = Ademco Slow; 1 = Silent Knight; 2 = Sescoa; 3 = Ademco Express; 4 = Ademco Contact ID;
5 = SIA (not supported with GPRS/IP reporting)
[811] ___/___/___/___ Partition 1 account number (landline communication only)
[812] ___/___/___/___ Partition 2 account number (landline communication only)

Landline Communication
Use worksheet 37 to record your settings for sections [815] to [819]. This worksheet applies to both landline communication.

Worksheet 37: Landline Communication Settings

Section Data Description
[815] __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__ Monitoring station telephone number 1
[816] __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__ Monitoring station telephone number 2
[817] __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__ Backup telephone number

Table 39: Special keys for telephone numbers (does not apply to TM Keypads)

Function Keypad Key Function Keypad Key

* OFF Four-second pause TBL NOTE: To erase a phone number or numeric
# BYP Delete current digit SLEEP message, press sleep for each digit, in the
respective section.
Switch from pulse to tone dialing, or vice-versa MEM Insert a blank space

Timers
Use worksheet 38 to record your settings for sections [820] to [840]. For additional timers, see worksheets 39 and 47 on pages 44 and 50, respectively.

Worksheet 38: Communication Timers

Section Data Description Default
[820] ___/___/___ 000 to 255 hours Fail to comm. clear event timer 000 = disabled
[830] ___/___/___ 000 to 255 x 2 seconds TLM fail delay (landline only) 016
[831] ___/___/___ 000 to 032 Maximum dialing attempts monitoring station (landline only) 008
[832] ___/___/___ 000 to 127 seconds Delay between dialing attempts* (landline only) 020
[833] ___/___/___ 000 to 255 seconds Delay alarm transmission 000
[838] ___/___/___ 000 to 255 seconds Recent closing delay 000
[839] ___/___/___ 000 to 255 minutes Power failure report delay** 015
[840] ___/___/___ 000 to 255 days Auto test report (see table 36 on page 41) 000
* Also applicable when using a VDMP3 Plug-in Voice Dialer.
**For EN 50131, the maximum value for power failure delay is 60 minutes.

43
 SP+ Series Programming Guide

Test Report and Report Delays

Use worksheet 39 to record your settings for sections [850] to [852]. For additional timers, see worksheets 38 and 47 on pages 43 and 50, respectively.

Worksheet 39: Test Report and Report Delays

Section Data Description Default
[850] ___/___/___ HH:MM Auto test report time of day (see table 36 on page 41) 00:00
[851] ___/___/___ 000 to 255 minutes Armed report delay 005
[852] ___/___/___ 000 to 255 minutes Disarmed report delay 060

System and Communication Report Codes

Use the following section to program system report codes, as well as additional communication report codes on your SP+ control panel.
Entering Report Codes
• For Ademco slow, Silent Knight, SESCOA, and Ademco express formats, key-in the desired two-digit hex value from 00 to FF.
• For Ademco Programmable Format, enter the desired two-digit hex value, found in table 41 on page 46. Entering FF will set the report code to those
outlined in table 42 on page 48.
• For Ademco All Codes Format, the control panel automatically generates report codes from the ones found in table 42 on page 48.

Special Arming and Disarming Report Codes

Use worksheet 40 to record your settings for special arming and disarming report codes.

Worksheet 40: Special Arming and Disarming Report Codes

Section Data Description Section Data Description Section Data Description
___/___ Auto-arming ___/___ Quick arming ___/___ Cancel auto-arm
___/___ Late to close ___/___ Arming via PC ___/___ Disarming via PC
[860] [861] [862] Cancel alarm with user or
___/___ No movement ___/___ Arming with keyswitch ___/___
BabyWare
___/___ Partial arming ___/___ - ___/___ Cancel paramedic
Default: FF

Special Alarm Report Codes

Use worksheet 41 to record your settings for special alarm report codes.

Worksheet 41: Special Alarm Report Codes

Section Data Description Section Data Description
___/___ Emergency panic ___/___ Zone shutdown
___/___ Auxiliary panic ___/___ Duress
[863] [864]
___/___ Fire panic ___/___ Keypad lockout
___/___ Recent closing ___/___ Paramedic alarm
Default: FF

44
SP+ Series Programming Guide

System Trouble Report Codes Use worksheet 42 to record your settings for system
trouble report codes.
Worksheet 42: Special Trouble Report Codes
Section Data Description Section Data Description Section Data Description
___/___ - ___/___ Bell output overload ___/___ Fail to communicate
___/___ AC failure ___/___ Bell output disconnected ___/___ RF jamming
[865] [866] [867]
___/___ Battery failure ___/___ Timer loss ___/___ Module lost
___/___ Auxiliary supply ___/___ Fire loop trouble ___/___ Module tamper
Wireless module
___/___ Module power fail ___/___ Default: FF
supervision lost
[868] ___/___ Module low/no battery* [869] ___/___ Wireless module tamper
___/___ Wireless zone low battery ___/___ Remote low battery
___/___ Wireless zone supervision lost ___/___ -

System Trouble Restore Codes Use worksheet 43 to record your settings for system
trouble restore codes.
Worksheet 43: System Trouble Restore Codes
Section Data Description Section Data Description Section Data Description
___/___ TLM ___/___ Bell output overload ___/___ Fail to communicate
___/___ AC failure ___/___ Bell output disconnect ___/___ RF jamming
[870] [871] [872]
___/___ Battery failure ___/___ Timer loss ___/___ Module lost
___/___ Auxiliary supply ___/___ Fire loop trouble ___/___ Module tamper
Wireless module
___/___ Module power fail ___/___ Default: FF
supervision lost*
[873] ___/___ Module low/no battery* [874] ___/___ Wireless module tamper
___/___ Wireless zone low battery ___/___ Remote low battery
___/___ Wireless zone supervision lost ___/___ -

System Special Report Codes Use worksheet 44 to record your settings for system
special report codes.
Worksheet 44: System Special Report Codes
Section Data Description Section Data Description Section Data Description
___/___ Cold start ___/___ Installer in ___/___ -
___/___ Test report ___/___ Installer out ___/___ -
[875] [876] [877]
___/___ - ___/___ Closing delinquency ___/___ -
___/___ Software out ___/___ - ___/___ Fail to arm
Default: FF

NOTE: For report code formatting instructions, see Installer Function Keys
Entering Report Codes on page 44.
Table 40: Description of installer functions for SP+ keypads

Function Action Description

Test report ENTER + installer code + ENTER Sends the Test Report report code programmed in section [875], to the monitoring station.
Cancels all communication with the BabyWare software or with the monitoring station, until the next
Cancel communication ENTER + installer code + STAY
reportable event.
Answer BabyWare Will force the console to answer an incoming call from the monitoring station, which is using the
ENTER + installer code + SLEEP
software BabyWare software.
Call BabyWare Will dial the PC telephone number programmed in section [915], thereby initiating communication
ENTER + installer code + BYP
software with a computer using the BabyWare software.
This mode allows to perform walk tests, where the siren will squawk to indicate opened zones.
Installer test mode ENTER + installer code + TBL
To exit, press TBL.

45
 SP+ Series Programming Guide

Contact ID Report Codes Table 41: Ademco contact ID report codes (Continued) Table 41: Ademco contact ID report codes (Continued)
Table 41: Ademco contact ID report codes
Type CID # Reporting Code Value Type CID # Reporting Code Value
Type CID # Reporting Code Value 150 24-hour non-burglary 25 330 System peripheral 4F
100 Medical alarm 01 151 Gas detected 26 331 Polling loop open 50
Medical Alarms

101 Pendant transmitter 02 152 Refrigeration 27 332 Polling loop short 51

(100)

153 Loss of heat 28 333 Expansion module failure 52

102 Fail to report in 03

System Peripheral Troubles

24-hour Non-burglary
154 Water leakage 29 334 Repeater failure 53

(150 & 160)

110 Fire Alarm 04 155 Foil break 2A 335 Local printer paper out 54

(330 & 340)

111 Smoke 05 156 Day trouble 2B 336 Local printer failure 55

112 Combustion 06 157 Low bottled gas level 2C 337 Exp. module DC loss 56
158 High temperature 2D 338 Exp. module low battery 57
Fire Alarms

113 Water Flow 07

(110)

114 Heat 08 159 Low temperature 2E 339 Exp. module reset 58

115 Pull Station 09 161 Loss of air flow 2F 341 Exp. module tamper 59

116 Duct 0A 162 Carbon monoxide detected 30 342 Exp. module AC loss 5A

117 Flame 0B 163 Tank level 31 343 Exp. module self-test fail 5B

118 Near Alarm 0C 200 Fire supervisory 32 344 RF receiver jam detected 5C

120 Panic alarm 0D 201 Low water pressure 33 350 Communication 5D

Fire Supervisory
(200 & 210)

121 Duress 0E 202 Low CO2 34 351 Telco fault 1 5E

Communication Troubles
Panic Alarms

122 Silent 0F 203 Gate valve sensor 35 352 Telco fault 2 5F

(120)

(350 & 360)

123 Audible 10 204 Low water level 36 353 Long range radio 60

124 Duress - access granted 11 205 Pump activated 37 354 Fail to communicate 61

125 Duress - egress granted 12 206 Pump failure 38 355 Loss of radio supervision 62

130 Burglary 13 300 System trouble 39 356 Loss of central polling 63

131 Perimeter 14 301 AC loss 3A Long range radio VSWR

357 64
problem
132 Interior 15 302 Low system battery 3B
370 Protection loop 65
133 24-hour 16 303 RAM checksum bad 3C
Burglar Alarms

371 Protection loop open 66

Protection Loop Troubles

134 Entry/exit 17 304 ROM checksum 3D
(130)

372 Protection loop short 67

135 Day/night 18 305 System reset 3E
System Troubles

373 Fire trouble 68

(300 & 310)

136 Outdoor 19 306 Panel program changed 3F (370)

374 Exit error alarm 69
137 Tamper 1A 307 Self-test failure 40
375 Panic zone trouble 6A
138 Near alarm 1B 308 System shutdown 41
376 Hold-up zone trouble 6B
139 Intrusion verifier 1C 309 Battery test failure 42
377 Swinger trouble 6C
140 General alarm 1D 310 Ground fault 43
378 Cross-zone trouble 6D
141 Polling loop open 1E 311 Battery missing/dead 44
380 Sensor trouble 6E
Powr. supply over current
General Alarms

142 Polling loop short 1F 312 45

limit 381 Loss of supervision - RF 6F
143 Extension module failure 20
(140)

313 Engineer reset 46 382 Loss of supervision - RPM 70

144 Sensor tamper 21
320 Sounder relay 47 383 Sensor tamper 71
145 Expansion module tamper 22
321 Bell 1 48 384 RF transmitter low battery 72
Sounder/Relay Troubles

146 Silent burglary 23

322 Bell 2 49 385 Smoke detector hi sensitivity 73
Sensor Troubles

147 Sensor supervision failure 24

(380 & 390)

323 Alarm relay 4A Smoke detector low

(320)

386 74
sensitivity
324 Trouble relay 4B
Intrusion detector hi
325 Reversing relay 4C 387 75
sensitivity
326 Notification appliance chk. #3 4D Intrusion detector low
388 76
327 Notification appliance chk. #4 4E sensitivity
389 Sensor self-test failure 77
391 Sensor watch trouble 78
392 Drift compensation error 79
393 Maintenance alert 7A

46
SP+ Series Programming Guide

Table 41: Ademco contact ID report codes (Continued) Table 41: Ademco contact ID report codes (Continued) Table 41: Ademco contact ID report codes (Continued)

Type CID # Reporting Code Value Type CID # Reporting Code Value Type CID # Reporting Code Value
400 Open/close 7B 520 Sounder/relay disabled A9 601 Manual trigger test BD
401 Open/close by user 7C 521 Bell 1 disabled AA 602 Periodic test report BE

Sounder Relay Disabled

402 Group open/close 7D 522 Bell 2 disabled AB 603 Periodic RF transmission BF
Open/Close

403 Automatic open/close 7E 523 Alarm relay disabled AC 604 Fire test C0
(400)

(520)
406 Cancel 7F 524 Trouble relay disabled AD 605 Status report to follow C1
407 Remote arm/disarm 80 525 Reversing relay disabled AE 606 Listen-in to follow C2
408 Quick arm 81 Notification appliance chk. #3 607 Walk test mode C3
526 AF
disabled
409 Keyswitch open/close 82 Periodic test - system trouble
608 C4
Notification appliance chk. #4 present
411 Call back request made 83 527 B0
disabled
609 Video transmitter active C5
412 Successful - download access 84
Remote Access

Communication Disabled Modules

531 Module added B1

(530)
611 Point test OK C6
413 Unsuccessful access 85
(410)

532 Module removed B2 612 Point not tested C7

414 System shutdown 86
551 Dialer disabled B3 613 Intrusion zone walk tested C8
415 Dialer shutdown 87
614 Fire zone walk tested C9

Test/Misc
416 Successful upload 88
(550 & 560)

(600)
615 Panic zone walk tested CA
421 Access denied 89
552 Radio transmitter disabled B4 616 Service request CB
422 Access report by user 8A
621 Event log reset CC
423 Forced access 8B
622 Event log 50% full CD
424 Egress denied 8C
623 Event log 90% full CE
425 Egress granted 8D 570 Zone bypass B5
624 Event log overflow CF
426 Access door propped open 8E 571 Fire bypass B6
Access Control

625 Time/date reset D0

(420 & 430)

Access point door status 572 24-hour zone bypass B7

427 8F
monitor trouble 626 Time/date inaccurate D1
Bypasses

573 Burglary bypass B8

(570)

428 Access point request to exit 90 627 Program mode entry D2

574 Group bypass B9
429 Access program mode entry 91 628 Program mode exit D3
575 Swinger bypass BA
430 Access program mode exit 92 629 32-hour event log marker D4
576 Access zone shunt BB
431 Access threat level change 93 630 Schedule change D5
577 Access point bypass BC
432 Access relay/trigger fail 94 631 Exception schedule change D6
433 Access RTE shunt 95 632 Access schedule change D7
434 Access DSM shunt 96 654 System inactivity D8
441 Armed stay 97
442 Keyswitch armed stay 98
450 Exception open/close 99
451 Early open/close 9A
452 Late open/close 9B
(440 & 450)
Arming

453 Failed to open 9C

454 Failed to close 9D
455 Auto-arm failed 9E
456 Partial arm 9F
457 User exit error A0
458 User on premises A1
459 Recent close A2
461 Wrong code entry A3
462 Legal code entry A4
System

463 Re-arm after alarm A5

(460)

464 Auto-arm time extended A6

465 Panic alarm reset A7
466 Service ON/OFF premises A8

47
 SP+ Series Programming Guide

Automatic Report Codes

Table 42: List of automatic report codes

System Event Default Contact ID Report Code Default SIA Report Code
Arming with user code (##) 3 4A1 Close by user CL Closing report
Auto arming 3 4A3 Automatic close CA Automatic closing
Late to close 3 452 Late to close OT Late to close
No movement 3 452 Late to close NA No activity
Partial arming 1 456 Group bypass CG Close area
Quick arming 3 4A8 Quick arm CL Closing report
Arm with PC software 3 4A7 Remote arm/disarm CQ Remote arming
Keyswitch arming 3 4A9 Keyswitch arming CS Keyswitch arming
Disarm with user code (##) 1 4A1 Open by user OP Opening report
Disarm after alarm with user code (##) 1 4A1 Open by user OP Opening report
Cancel alarm with user code (##) 1 4A6 Cancel by user OR Disarm from alarm
Auto arming cancellation 1 464 Deferred open/close CE Closing extend
Disarm with PC software 1 4A7 Remote arm/disarm OQ Remote disarming
Disarm after an alarm with PC software 1 4A7 Remote arm/disarm OR Disarm from alarm
Cancel alarm with PC software 1 4A6 Cancel by user OR Disarm from alarm
Cancel paramedic alarm 1 4A6 Cancel by user MH Medical alarm restore
Keyswitch disarm 1 4A9 Keyswitch disarm OS Keyswitch disarm
Keyswitch disarm after alarm 1 4A1 Keyswitch disarm after alarm OS Keyswitch disarm after alarm
Keyswitch cancel alarm 1 4A6 Keyswitch cancel alarm OS Keyswitch cancel alarm
Zone bypassed (##) 1 57A Zone bypass UB Untyped zone bypass
Zone alarm (##) 1 13A Burglary alarm BA Burglary alarm
Fire alarm (##) 1 11A Fire alarm FA Fire alarm
Zone alarm restore (##) 3 13A Burglary alarm restore BH Burglary alarm restore
Fire alarm restore (##) 3 11A Fire alarm restore FH Fire alarm restore
24-hr gas alarm (##) 1 151 Gas detected GA Gas alarm
24-hr heat alarm (##) 1 153 Loss of heat KA Heat alarm
24-hr water alarm (##) 1 154 Water leakage WA Water alarm
24-hr freeze alarm (##) 1 152 Refrigeration ZA Freeze alarm
24-hr gas alarm restore (##) 3 151 Gas restore GR Gas alarm restore
24-hr heat alarm restore (##) 3 153 Heat restore KR Heat alarm restore
24-hr water alarm restore (##) 3 154 Water restore WR Water alarm restore
24-hr freeze alarm restore (##) 3 152 Freeze restore ZR Freeze alarm restore
24-hr hold-up alarm 1 12A Panic alarm PA Panic alarm
24-hr hold-up alarm restore 3 12A Panic alarm restore PR Panic restore
Panic 1: emergency 1 12A Panic alarm PA Panic alarm
Panic 2: medical 1 1AA Medical alarm MA Medical alarm
Panic 3: fire 1 115 Pull station FA Fire alarm
Recent closing 3 459 Open/close CR Recent closing
Global zone shutdown 1 575 Group bypass CG Close area
Duress alarm 1 121 Duress HA Hold-up alarm
Keypad lockout 1 421 Access denied JA User code tamper
Zone shutdown (##) 1 57A Zone bypass UB Untyped zone bypass
Zone tampered (##) 1 144 Sensor tamper TA Tamper alarm
Zone tamper restore (##) 3 144 Sensor tamper restore TR Tamper restoral
TLM Trouble 1 351 Telco 1 fault LT Phone line trouble
AC failure 1 3A1 AC loss AT AC trouble
Battery failure 1 3A9 Battery test failure YT System battery trouble
Auxiliary supply trouble 1 3AA System trouble YP Power supply trouble
Bell output current limit 1 321 Bell 1 YA Bell fault

48
SP+ Series Programming Guide

Table 42: List of automatic report codes (Continued)

System Event Default Contact ID Report Code Default SIA Report Code
Bell absent 1 321 Bell 1 YA Bell fault
Clock lost 1 626 Time/date inaccurate JT Time changed
Fire loop trouble 1 373 Fire trouble FT Fire trouble
Communication fail 1 354 Communication fail YC Fail to communicate
RF jamming 1 344 RF receiver jam detection XQ RF jamming
GPRS module RF interference 1 552 Radio transmitter disabled YS Communication trouble
GPRS network failure 1 552 Radio transmitter disabled YS Communication trouble
GPRS supervision lost 1 552 Radio transmitter disabled YS Communication trouble
GPRS fail to communicate 1 354 Communication fails YC Fail to communicate
IP network failure 1 552 Radio transmitter disabled YS Communication trouble
IP supervision lost 1 552 Radio transmitter disabled YS Communication trouble
IP fail to communicate 1 354 Communication fails YC Fail to communicate
TLM trouble restore 3 351 Telco 1 fault restore LR Phone line restoral
AC failure restore 3 3A1 AC loss restore AR AC restoral
Battery failure restore 3 3A9 Battery test restore YR System battery restoral
Auxiliary supply trouble restore 3 3AA System trouble restore YQ Power supply restored
Bell output current limit restore 3 321 Bell 1 restore YH Bell restored
Bell absent restore 3 321 Bell 1 restore YH Bell restored
Clock programmed 3 625 Time/date reset JT Time changed
Fire loop trouble restore 3 373 Fire trouble restore FJ Fire trouble restore
Fail to communicate with monitoring station restore 3 354 Fail to communicate restore YK Communication fails restore
RF jamming restore 3 344 RF receiver jam detection restore XH RF jamming restoral
GPRS module RF interference restore 3 552 Radio transmitter restore YK Communication restore
GPRS network restore 3 552 Radio transmitter restore YK Communication restore
GPRS supervision restore 3 552 Radio transmitter restore YK Communication restore
GPRS fail to communicate restore 3 354 Communication restore YK Fail to communicate restore
IP network restore 3 552 Radio transmitter restore YK Communication restore
IP supervision restore 3 552 Radio transmitter restore YK Communication restore
IP fail to communicate restore 3 354 Communication restore YK Fail to communicate restore
Combus fault 1 333 Expansion module failure ET Expansion trouble
Module tamper 1 341 Expansion module tamper TA Tamper alarm
Module AC fail 1 342 AC failure on module AT Module AC fail
Module battery fail 1 338 Battery failure on module YT Module battery fail
Bus fault restore 3 333 Expansion module failure restore ER Expansion restoral
Module tamper restore 3 341 Expansion module tamper restore TR Tamper restoral
Module AC fail restore 3 342 AC restored on module AR Module AC fail restore
Module battery fail restore 3 338 Battery failure on module YR Module battery fail restore
Cold start 1 3A8 System shutdown RR Power up
Test report engaged 1 6A2 Periodic test report TX Test report
PC software communication finished 1 412 Successful - download access RS Remote program success
Installer on site 1 627 Program mode entry LB Local program
Installer programming finished 1 628 Program mode exit LS Local program success
Maintenance in 1 627 Program mode entry LB Local program
Maintenance out 1 628 Program mode exit LS Local program success
Closing delinquency 1 654 System inactivity CD System inactivity
Manual trigger test in 1 6A1 Manual trigger test in TS Manual trigger test in
Manual trigger test out 3 6A1 Manual trigger test out TS Manual trigger test out
Exit error 1 374 Exit error EE Exit error
RF module low battery 1 384 RF transmitter low battery XT Transmitter battery trouble
RF module battery restore 3 384 RF transmitter battery restore XR Transmitter battery restoral

49
 SP+ Series Programming Guide

Table 42: List of automatic report codes (Continued)

System Event Default Contact ID Report Code Default SIA Report Code
RF zone supervision lost 1 381 Loss of supervision - RF US Untype zone supervision
RF zone supervision restore 3 381 Supervision restore - RF UR Untyped zone restoral
RF module supervision lost 1 381 Loss of supervision - RF US Untyped zone supervision
RF module supervision restore 3 381 Loss of supervision - RF restore UR Untyped zone restoral
RF module tamper 1 145 Expansion module tamper ES Expansion device tamper
RF module tamper restore 3 145 Expansion module tamper restore EJ Expansion device restore
Paramedic alarm 1 1AA Medical MA Medical alarm
Zone forced 1 57A Zone forced XW Zone forced
Zone included 3 57A Zone included UU Zone included
Remote low battery 1 338 Battery failure on module YT Module battery fail
Remote low battery restore 3 338 Battery failure on module restore YR Module battery fail restore
Failed to arm 1 454 Failed to close CI Failed to close

Communication Report Codes

Use worksheet 45 to record your settings for communication report codes. Sections [879] and [884] apply to network GPRS communications. See Communication
Programming on page 41, for more communication features. In addition, refer to Description of Sections [966] and [967] on page 53, for clearing and resetting codes.

Worksheet 45: Communication Report Codes

Section Data Description Section Data Description Section Data Description
___/___ PCS series RF jam ___/___ - ___/___ N/A
___/___ PCS series no service ___/___ IP Module no service ___/___ -
PCS series module
[879] ___/___ [880] ___/___ IP Module supervision lost [884] ___/___ -
supervision lost
Receiver fail to IP receiver fail to
___/___ ___/___ ___/___ -
communicate (GPRS) communicate

Communication Restore Report Codes

Use worksheet 46 to record your settings for communication restore report codes. Section [881] applies to network GPRS communications.

Worksheet 46: Communication Restore Report Codes

Section Data Description Section Data Description
___/___ PCS series RF jam ___/___ -
___/___ PCS series no service ___/___ IP Module no service
[881] [882]
___/___ PCS series module supervision lost ___/___ IP Module supervision lost
___/___ Receiver fail to communicate (GPRS) ___/___ IP receiver fail to communicate

Software Options and Additional Timers

Use the following section to program software options and additional communication timers on your SP+ control panel.
Table 43: Description of section [900] (BabyWare options)

Section Option Description OFF ON

1 Call back  Disabled  Enabled
[900]
2 Automatic event buffer transmission  Disabled  Enabled

= Default

Additional Communication Timers

Use worksheet 47 to record your settings for sections [901] and [902]. For additional timers, see worksheets 38 and 39.

Worksheet 47: Additional Communication Timers

Section Data Description Default
[901] ___/___/___ 000 to 255 rings Number of rings 008
[902] ___/___/___ 000 to 255 secs. (max 127) Answering machine override delay 030

50
SP+ Series Programming Guide

BabyWare Options
Use worksheet 48 to record your settings for BabyWare options.

Worksheet 48: BabyWare Options

Section Data Description
[910] ___/___/___/___ Panel ID
[911] ___/___/___/___ PC password
[915] __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__ PC telephone number (landline communication only)
NOTE: For increased communication security, you will be prompted to change the default panel ID and PC password.

IP and Software Configurations

Use the following section to configure IP and software requirements on your SP+ control panel.

IP Account Numbers
Use worksheet 49 to record the IP account numbers for network communication.

Worksheet 49: IP Account Numbers

Section Data Description
[918] ___/___/___/___ IP account partition 1
[919] ___/___/___/___ IP account partition 2

Software and PCS Connection Settings

Use worksheet 50 to record connection settings for BabyWare and PCS series.

Worksheet 50: Software and PCS Connection Settings

Section Data Description Default
[920] __/__/__/__/__ Port 10000
[921] __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__ Access point name (APN), part 1 (e.g., internet.com) -
[922] __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__ Access point name (APN), part 2 -
[923] __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__ User name, part 1 -
[924] __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__ User name, part 2 -
[925] __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__ Password, part 1 -
[926] __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__ Password, part 2 -
[927] __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__ Installer software password (BabyWare) admin

IP Receiver Configurations
Use worksheets 51 to 53 (on page 52) to configure IP receivers. Table 44 provides a description of the IP/GPRS registration status.
Table 44: IP/GPRS registration status

Key Main Menu Trouble Key Sub-menu Trouble

1 OFF = Unregistered
1 IP/GPRS module registration status 1 Slow flash = Registering
1 ON = Registration OK
7 No IP/GPRS module
2 IP/GPRS module error 8 Ethernet cable unplugged; PCS no service
9 No IP address acquired by module/GPRS network trouble
7 No IP address (not programmed)
8 No IP port (not programmed)
3 IP/GPRS programming error
9 No IP account (not programmed)
10 No access point name (not programmed; GPRS only)
7 Cannot connect
8 Invalid profile
4 IP/GPRS registration error
9 Invalid format
10 Account already registered under another MAC address
Register module - When all troubles are cleared, press ARM to register module

51
 SP+ Series Programming Guide

Worksheet 51: IP Receiver 1 Configuration

Section Data Description Default
WAN1 IP address (e.g., 100.100.100.100); for one or
-
[929] __/__/__ . __/__/__ . __/__/__ . __/__/__ two-digit numbers, add 0s before the first digit
[930] __/__/__/__/__ WAN1 IP port 10000
[931] __/__/__ . __/__/__ . __/__/__ . __/__/__ WAN2 IP address -
[932] __/__/__/__/__ WAN2 IP port 10000
[933] __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__ IP password 123456
[934] __/__ IP profile (e.g., 01) -
[935] To view status or to register, press ARM (see table 44 on page 51) IP receiver status -

Worksheet 52: IP Receiver 2 Configuration

Section Data Description Default
[936] __/__/__ . __/__/__ . __/__/__ . __/__/__ WAN1 IP address (e.g., 100.100.100.100) -
[937] __/__/__/__/__ WAN1 IP port 10000
[938] __/__/__ . __/__/__ . __/__/__ . __/__/__ WAN2 IP address -
[939] __/__/__/__/__ WAN2 IP port 10000
[940] __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__ IP password 123456
[941] __/__ IP profile (e.g., 01) -
[942] To view status or to register, press ARM (see table 44 on page 51) IP receiver status -

Worksheet 53: IP Receiver Backup Configuration

Section Data Description Default
[943] __/__/__ . __/__/__ . __/__/__ . __/__/__ WAN1 IP address (e.g., 100.100.100.100) -
[944] __/__/__/__/__ WAN1 IP port 10000
[945] __/__/__ . __/__/__ . __/__/__ . __/__/__ WAN2 IP address -
[946] __/__/__/__/__ WAN2 IP port 10000
[947] __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__ IP password 123456
[948] __/__ IP profile (e.g., 01) -
[949] To view status or to register, press ARM (see table 44 on page 51) IP receiver status -

Usability Sections
The sections described in the ensuing segment are used to clear, reset, and display various settings and features on your SP+ control panel.

Description of Sections [950], [955], and [960]

Table 45: Description of sections [950], [955], and [960]

Section Description
[950] Resets all programmable sections to their respective factory-set, default values. Once accessed, press ENTER to reset.
[951] Sets panel for EN 50131 compliancy. To set the panel, enter section [951] and press ENTER.
[955] Clears bus module troubles. Once cleared, remove disconnected module from the bus.
Displays the wireless transmitter serial number. Once accessed, press any button on the assigned remote control, or
[960]
press the tamper switch of the download memory key. Press ENTER to view the next digit.

Description of Section [965]

Table 46: Description of section [965] (reset labels)

Option Description OFF ON

1 Reset zone labels  Disabled  Enabled
2 Reset user labels  Disabled  Enabled
Section [965]

3 Reset partition labels  Disabled  Enabled

4 Reset PGM labels  Disabled  Enabled
5 Reset bus module labels  Disabled  Enabled
6 Reset wireless repeater and siren labels  Disabled  Enabled
7 Reset wireless keypad, repeater, and siren labels  Disabled  Enabled

= Default

NOTE: When resetting any option in section [965], ensure that all other options are deselected. Press ENTER to reset the respective set of labels to their default
values, before exiting the section.

52
SP+ Series Programming Guide

Description of Sections [966] and [967]

Table 47: Description of sections [966] and [967] (clear and reset report codes)

Option Description OFF ON Option Description OFF ON

1 Clear zone report codes  Disabled  Enabled 1 Reset zone report codes to default  Disabled  Enabled

2 Clear user report codes  Disabled  Enabled 2 Reset user report codes to default  Disabled  Enabled
Section [966]

Section [967]
Reset arm/disarm/alarm report codes
3 Clear arm/disarm/alarm report codes  Disabled  Enabled 3  Disabled  Enabled
to default
4 Clear trouble report codes  Disabled  Enabled 4 Reset trouble report codes to default  Disabled  Enabled
Reset system special report codes to
5 Clear system special report codes  Disabled  Enabled 5  Disabled  Enabled
default
Clear report code for PCS lost Reset report code for PCS lost
6  Disabled  Enabled 6  Disabled  Enabled
communication with panel communication with panel

= Default

NOTE: When clearing or resetting any option in sections [966] AND [967], ensure that all other options are deselected. Press ENTER to reset the respective set of
labels to their default values, before exiting the section.

Description of Sections [970], [975], and [980]

Table 48: Description of sections [970], [975], and [980]

Section Description
[970] Downloads data from the memory key to the control panel. To download data, enter section [970], and then press ENTER.
[975] Uploads data from the control panel to the memory key. To upload data, enter section [975], and then press ENTER.
[980] Displays version number of the control panel. Once accessed, press ENTER to view the next digit.

Label Programming with LCD Keypads

Use the information in the following section to program system labels, using an LCD keypad (K32LCD+).

Function keys
Table 49: Description of the special function keys, used for programming labels on LCD keypads

Function Keypad Key

Insert space STAY

Delete SLEEP

Delete entire entry ARM

Toggle between numeric and alphanumeric keys OFF

Toggle between lower and upper case keys BYP

Insert special characters ENTER

53
 SP+ Series Programming Guide

Catalogue of Special Characters

The following section outlines the different catalogues of special characters, including those in Hebrew, Greek, and Russian.
Figure 1: Standard special characters Figure 2: Hebrew special characters

032 048 064 080 096 112 160 176 192 208 224 240

033 049 065 081 097 113 161 177 193 209 225 241

034 050 066 082 098 114 162 178 194 210 226 242

035 051 067 083 099 115 163 179 195 211 227 243

036 052 068 084 100 116 164 180 196 212 228 244

037 053 069 085 101 117 165 181 197 213 229 245

038 054 070 086 102 118 166 182 198 214 230 246

039 055 071 087 103 119 167 183 199 215 231 247

040 056 072 088 104 120 168 184 200 216 232 248

041 057 073 089 105 121 169 185 201 217 233 249

042 058 074 090 106 122 170 186 202 218 234 250

043 059 075 091 107 123 171 187 203 219 235 251

044 060 076 092 108 124 172 188 204 220 236 252

045 061 077 093 109 125 173 189 205 221 237 253

046 062 078 094 110 126 174 190 206 222 238 254

047 063 079 095 111 127 175 191 207 223 239 255

Figure 4: Greek special characters

016 032 048 064 080 096 112 128 144 160 176 192 208 224 240

017 033 049 065 081 097 113 129 145 161 177 193 209 225 241

Figure 3: Russian special characters 018 034 050 066 082 098 114 130 146 162 178 194 210 226 242

019 035 051 067 083 099 115 131 147 163 179 195 211 227 243

020 036 052 068 084 100 116 132 148 164 180 196 212 228 244

021 037 053 A069 085 101 117 133 149 165 181 197 213 229 245

022 038 054 070 086 102 118 134 150 166 182 198 214 230 246

023 039 055 071 087 103 119 135 151 167 183 199 215 231 247

024 040 056 072 088 104 120 136 152 168 184 200 216 232 248

025 041 057 073 089 105 121 137 153 169 185 201 217 233 249

026 042 058 074 090 106 122 138 154 170 186 202 218 234 250

027 043 059 075 091 107 123 139 155 171 187 203 219 235 251

028 044 060 076 092 108 124 140 156 172 188 204 220 236 252

029 045 061 077 093 109 125 141 157 173 189 205 221 237 253

030 046 062 078 094 110 126 142 158 174 190 206 222 238 254

031 047 063 079 095 111 127 143 159 175 191 207 223 239 255

Figure 5: Polish, Hungarian, and Turkish special characters

001 002 003 004 005 006 007

Polish

001 002 003

Hungarian

001
Turkish

54
SP+ Series Programming Guide

Keypad Letter Assignments

The following section outlines the different configurations for keypad letter assignments, including those in Hebrew, Greek, and Russian.
Table 50: Standard keypad letter assignment Figure 6: Hebrew keypad letter assignment

Press Key Press Key Press Key

Key
Once Twice Three Times
1 A B C
2 D E F
3 G H I
4 J K L
5 M N O
6 P Q R
7 S T U
8 V W X
9 Y Z

Table 51: Greek keypad letter assignment

Figure 7: Russian keypad letter assignment
Press Key Press Key Press Key
Key
Once Twice Three Times
1 A B G
2 D E Z
3 H Q I
4 K L M
5 N O
6 P R S
7 T U F
8 C Y W

Trouble Display
The following section provides information on the different troubles associated with your SP+ control panel. To view the trouble display, press TBL on your
SP+ keypad. Table 52 outlines the troubles appearing in the main menu and their corresponding sub-menu troubles. To view the sub-menu troubles, press the
trouble’s respective key in the main menu.
NOTE: Keypads can be programmed to emit a beep every five seconds, whenever a new trouble condition has occurred. Press TBL to stop the beeping.
Table 52: Description of troubles for SP+ control panels

Key Main Menu Trouble Key Sub-menu Trouble

1 Wireless zone low battery 1 to 32 Zones in low battery
1 Low/no battery on the control panel
2 AC failure on control panel
3 Auxiliary overload on control panel
4 Wireless keypad AC failure
2 Power trouble 5 Wireless keypad battery failure
6 Wireless repeater AC failure
7 Wireless repeater battery failure
8 Wireless siren AC failure
9 Wireless siren battery failure
10 Remote low battery (press [0] to view which remote)
1 Bell disconnected on control panel
3 Bell trouble
2 Bell overload on control panel

55
 SP+ Series Programming Guide

Table 52: Description of troubles for SP+ control panels

1 Telephone line monitoring on control panel

2 Fail to communicate on monitoring telephone 1, on control panel
3 Fail to communicate on monitoring telephone 2, on control panel
5 Fail to communicate on voice telephone, on control panel
6 Fail to communicate with PC, on control panel
4 Communication trouble 7 Fail to communicate with IP receiver 1 or 2 (GPRS)
8 Fail to communicate with IP receiver 1 or 2 (IP)
9 N/A

10 IP module no service (network failure)

STAY PCS RF jamming
OFF IP receiver unregistered (IP/GPRS)
5 1 to 32 Zones in tamper and zone wiring failure
Tamper and zone wiring failure
STAY Panel tamper supervision
1 2WPGM
2 Keypad bus
6 Module tamper trouble 3 ZX8/ZX82 bus module
4 RTX3 bus module
5 Wireless siren
6 GPRS module
7 Fire loop trouble 1 to 32 Zones in fire loop trouble
8 Timer loss -
1 to 32 Zones in supervision lost
9 Wireless zone supervision loss
STAY RF jamming trouble
1 2WPGM
2 Keypad bus (panel reset will not clear this trouble; clear it in section [955])
3 ZX8/ZX82 bus module
4 RTX3 bus module
5 Wireless keypad
0 (10), or 10 Module supervision loss 6 Wireless repeater
7 -
8 VDMP3
9 PCS series
10 IP Module
STAY Wireless siren
16 Keypad fault (K32, K32RF, K37, K35 only) -
SLEEP Keypad fault (K636, K10V/H only) -

56
SP+ Series Programming Guide

Hardware Connections
Programmable Output Connections
When a specific event occurs in the system, a PGM can reset smoke detectors, activate strobe lights, open/close garage doors and much more.
PGMs
The control panels include two/four on-board programmable outputs (PGMs). PGM1 and PGM2 can support up to 150 mA. The PGMs are limited by the power
source being used. If powered by:
• The AUX terminals. The current consumption of the AUX terminals cannot exceed 700 mA. Therefore, whatever devices are connected to the AUX terminals
(e.g., modules and PGMs) cannot exceed 700 mA combined. For example, if there are six modules connected to the AUX terminals that are using 600 mA and
you wish to power the PGM using the AUX terminals, the PGM’s current consumption cannot exceed 100 mA.
• An external power supply. If using an external power supply, the current consumption cannot exceed 150 mA for PGM1 and PGM2. If the external power
supply’s current consumption limit is less than that of the PGM it is connected to, than the current consumption will not exceed the power supply’s current
limit.

Single Zone Inputs

Detection devices such as motion detectors and door contacts are connected to the control panel's zone input terminals. Figure 6 demonstrates single zone input
terminal connections recognized by the panel. Once connected, the associated zone's parameters must be defined.
Figure 6: Single Zone Input Connections

Advanced Technology Zone (ATZ) Connections (SP6000+ only)

57
 SP+ Series Programming Guide

Fire Circuits
When a zone is programmed as a fire zone, the zone becomes normally open and requires an EOL resistor. If a line short occurs or if the smoke detector becomes
active, whether the system is armed or disarmed, the control panel will generate an alarm. If a trouble occurs on a fire zone, the Fire Loop Trouble will appear in the
keypad’s trouble display (See “Trouble Display” on page 55.) and the control panel can transmit the Fire Loop Trouble report, if programmed, in section [866].

Figure 7: Fire Circuits

AC Power
Do not use any switch-controlled outlets to power the transformer to avoid accidental user AC shut off. Connect the transformer as shown in Figure 1. Use the below
table for appropriate transformer.

Use only a safety approved transformer with rated output voltage of 16.5 Vac and rated power of 40 VA (minimum).

SP5500+ SP6000+ SP7000+

Transformer:
16.5 VAC 40 VA (minimum)
(use only one of the following)
Panel DC power supply output rated at: 700 mA 1A 1.5A
Maximum allowed current supplied by all Auxiliary
1.1A 1.5A 1.75A
outputs:
Battery Charge Currents 700 mA

Backup Battery
To provide power during a power loss, connect a 12 Vdc 7 Ah or 4 Ah rechargeable lead acid or gel cell battery. Verify proper polarity as reversed connections will blow the
battery fuse.
Use only safety approved rechargeable battery with rated voltage of 12 Vdc and rated current of 7A maximum.

Battery Test
If the battery is disconnected or if the battery fuse is blown, a No/Low Battery failure will appear in the keypad’s trouble display (See “Trouble Display” on page 55.).
This trouble will also appear if the battery’s capacity is too low or if the voltage drops to 10.5V or lower while the control panel is running on the backup battery.
At 8.5V or lower, the panel shuts down and all outputs close. A battery protection disconnect occurs at 9.1 volts. If output voltage drops below 11.3 volts, a fault
signal is generated.

Demonstration or Emergency System Power-up without an AC Source

To power-up the control panel for demonstration or emergency purposes only, use a standard 12 VDC, 4 Ah/7 Ah backup battery. To power the control panel using
a backup battery:
1. Connect the battery to the control panel's BATT terminal.
2. Use a wire to short the battery's negative terminal to the panel's AUX- terminal.

58
SP+ Series Programming Guide

SP5500+ PCB Layout

Enter section [300] to

unlock your SP+ panel
serial ports for use with
third-party devices
using a TM70/TM50
Touch keypad and
K32LCD+.
To provide maximum
lightning protection we
strongly recommend having
separate earth connections
for the dialer and zone
ground terminals.

1 PGM Jumper: allows you to choose whether the solid state 9 Zone Input
relay PGMs are ground (-), or give out 12V (+) 10 The BELL output will shutdown if the current exceeds 3A
2 AUX LED: 11 PGM output connector
• ON = Aux present; OFF = Aux off 12 AC Power connections
3 Four-pin connector can be used for quick installation of a keypad 13 Backup Battery connections
4 EBUS and Dialer used with: 14 AWG#14 single conductor solid copper wire
• VDMP3 Plug-In Voice Module for voice reporting 15 Ground clamp
• PCS Series Communicator Module 16 Cold water pipe grounding
5 LEDs 17 To ground
Status LED: 18 Keypad’s zone configuration
• Flash once every second: Normal 19 Zone connections, if EOL is enabled, see section [706] option 2
• Flashes ON 1 sec. and OFF 1 sec.: Any trouble 20 To connect additional wiring to auxiliary power, use the red (+) and black
• Always ON: Panel is using phone line (-) keypad connectors; auxiliary power will shut down if current exceeds
• Fast flash 6 seconds after power-up: Installer lock enabled 1.1A; if the auxiliary output is overloaded and shuts down, you must
Charge LED: disconnect all loads from the output for at least 10 sec. before
Charging and battery test LED reconnecting any load back to the auxiliary output
6 Panel reset
7 Serial 1: Used as the primary reporting channel for connecting the IP
Module/PCS Module
8 Serial 2: Used as a backup reporting channel for connecting the IP
Module/PCS Module
The sum of the current drawn from the BELL and AUX must be limited to 1.3A. Exceeding this limit will overload the panel power supply
and lead to complete system shutdown.
40 VA transformer strongly recommended.
This equipment must be installed and maintained by qualified service personnel only.
Max. number of keypads: 15 bus modules
Max. aux. current: 700 mA
Power consumption (idle): 52 mA
Max. distance of bus module from panel: 76 m (250 ft.)
Max. total run of wire: 230 m (750 ft.)

59
 SP+ Series Programming Guide

SP6000+ PCB Layout

Do not cut, bend, or alter
the antenna, and ensure
that electrical wires or
other type of wires do
Enter section [300] to not cross over it, as this
unlock your SP+ panel may affect signal
serial ports for use with reception. Do not install
third-party devices the antenna near wires as
using a TM70/TM50 it may cause
Touch keypad, and interference.
K32LCD+.

To provide maximum lightning

protection we strongly
recommend having separate
earth connections for the dialer
and zone ground terminals.

1 PGM Jumper: allows you to choose whether the solid state 9 Zone Input
relay PGMs are ground (-), or give out 12V (+) 10 The BELL output will shutdown if the current exceeds 3A
2 AUX LED: 11 PGM output connector
• ON = Aux present; OFF = Aux off 12 AC Power connections
3 Four-pin connector can be used for quick installation of a keypad 13 Backup Battery connections
4 EBUS and Dialer used with: 14 AWG#14 single conductor solid copper wire
• VDMP3 Plug-In Voice Module for voice reporting 15 Ground clamp
• PCS Series Communicator Module 16 Cold water pipe grounding
5 LEDs 17 To ground
Status LED: 18 Keypad’s zone configuration
• Flash once every second: Normal 19 Zone connections, if EOL is enabled, see section [706] option 2
• Flashes ON 1 sec. and OFF 1 sec.: Any trouble 20 To connect additional wiring to auxiliary power, use the red (+) and black
• Always ON: Panel is using phone line (-) keypad connectors; auxiliary power will shut down if current exceeds
• Fast flash 6 seconds after power-up: Installer lock enabled 1.1A; if the auxiliary output is overloaded and shuts down, you must
Charge LED: disconnect all loads from the output for at least 10 sec. before
Charging and battery test LED reconnecting any load back to the auxiliary output
6 Panel reset
7 Serial 1: Used as the primary reporting channel for connecting the IP
Module/PCS Module
8 Serial 2: Used as a backup reporting channel for connecting the IP
Module/PCS Module
The sum of the current drawn from the BELL and AUX must be limited to 1.6A. Exceeding this limit will overload the panel power supply
and lead to complete system shutdown.
40 VA transformer strongly required.
This equipment must be installed and maintained by qualified service personnel only.
Max. number of keypads: 15 bus modules
Max. aux. current: 1000 mA
Power consumption (idle): 55 mA
Max. distance of bus module from panel: 76 m (250 ft.)
Max. total run of wire: 230 m (750 ft.)

60
SP+ Series Programming Guide

SP7000+ PCB Layout

Do not cut, bend, or alter
the antenna, and ensure
that electrical wires or
other type of wires do
Enter section [300] to not cross over it, as this
unlock your SP+ panel may affect signal
serial ports for use with reception. Do not install
third-party devices the antenna near wires as
using a TM70/TM50 it may cause
Touch keypad, and interference.
K32LCD+.

To provide maximum lightning

protection we strongly
recommend having separate
earth connections for the dialer
and zone ground terminals.

1 Four-pin connector can be used for quick installation of a keypad 8 Zone Input
2 AUX LED: 9 The BELL output will shutdown if the current exceeds 3A
• ON = Aux present; OFF = Aux off 10 PGMs: these jumpers allow you to choose whether the solid state relay
3 Panel reset PGMs are grounded (-), or give out 12V (+)
4 EBUS and Dialer used with: 11 AC Power connections
• VDMP3 Plug-In Voice Module for voice reporting 12 Backup Battery connections
• PCS Series Communicator Module 13 AWG#14 single conductor solid copper wire
5 LEDs 14 Ground clamp
Status LED: 15 Cold water pipe grounding
• Flash once every second: Normal 16 To ground
• Flashes ON 1 sec. and OFF 1 sec.: Any trouble 17 Keypad’s zone configuration
• Always ON: Panel is using phone line 18 Zone connections, if EOL is enabled, see section [706] option 2
• Fast flash 6 seconds after power-up: Installer lock enabled 19 To connect additional wiring to auxiliary power, use the red (+) and black
Charge LED: (-) keypad connectors; auxiliary power will shut down if current exceeds
Charging and battery test LED 1.1A; if the auxiliary output is overloaded and shuts down, you must
6 Serial 1: Used as the primary reporting channel for connecting the IP disconnect all loads from the output for at least 10 sec. before
Module/PCS Module reconnecting any load back to the auxiliary output
7 Serial 2: Used as a backup reporting channel for connecting the IP
Module/PCS Module

The sum of the current drawn from the BELL and AUX must be limited to 2.1A. Exceeding this limit will overload the panel power supply
and lead to complete system shutdown.
40 VA transformer strongly required.
This equipment must be installed and maintained by qualified service personnel only.
Max. number of keypads: 15 bus modules
Max. aux. current: 1500mA
Power consumption (idle): 46mA
Max. distance of bus module from panel: 76 m (250 ft.)
Max. total run of wire: 230 m (750 ft.)

61
 SP+ Series Programming Guide

Appendix A
EN 50131 Programming
The following sections describe all the programming required for your panel to be EN 50131 compliant.

To set your panel to be EN 50131 compliant:

1. Enter section [951] to unlock the software and set EN 50131 defaults.
2. Press Enter.
NOTE: All keypads in the system must have anti-tamper enabled in order to be EN 50131 compliant.
EN 50131 Standard System Defaults
The following sections are provide the system defaults that will be set for EN50131 compliancy. The following provides information on sections [700] through
[840].
Table 53: Description of section [700]

Section Option Option Type Description OFF ON

1 Partitioning Partitioning  Disabled  Enabled
2 Battery charging  350mA  700mA
General system options

Section [700]

3 Audible trouble warning (except AC failure) Disabled  Enabled

4 Audible trouble warning on AC failure  Disabled  Enabled
5 RF jamming supervision RF jamming supervision  Disabled  Enabled
6 Exit delay termination  Disabled  Enabled
General system options
7 Tamper supervision on the bus module  Disabled  Enabled
8 Panel Tamper Panel Tamper Supervision  Disabled  Enabled

Table 54: Description of section [703]

Section Option Option Type Description OFF ON

1 One-touch regular arming (also REM3)  Disabled  Enabled
2 One-touch stay arming (also REM3)  Disabled  Enabled
Keypad options 2
3 One-touch sleep arming (also REM3)  Disabled  Enabled

Section [703]

4 One-touch bypass programming Disabled  Enabled


5 Restrict arming on battery failure Disabled  Enabled

Restrict arming on tamper failure (zone + bus 

6 Arming/disarming options Disabled  Enabled
module + wireless PGM)

7
Restrict arming on supervision trouble;  Disabled  Enabled
wireless zones & PGM + bus module
8 Future Use - - - - -

ATZ, Zone Tamper and Supervision Options

Table 55: Description of section [705]

Option Description OFF ON

1 ATZ zone doubling  Disabled  Enabled
2 ATZ wiring options  Series  Parallel

Section [705]

3  Disabled Enabled
Tamper recognition (see following table)
4  Disabled  Enabled
5 Generate tamper on bypassed zone  No  Yes
6  Disabled  Enabled
Supervision options (see following table)
7  Disabled  Enabled
8 Generate supervision on bypassed zone  No  Yes

= Default

62
SP+ Series Programming Guide

Table 56: Description of options 3 & 4 and 6 & 7, in section [705]

Option Description
3 4 RF Zone/Hardwired Zone Tamper Recognition Options Keypad/Bus Module Tamper Recognition Options*
OFF OFF Disabled Disabled
OFF ON Trouble only Trouble only
ON OFF When disarmed: trouble only; when armed: follow zone’s alarm type Trouble only
ON ON When disarmed: audible alarm; when armed: follow zone’s alarm type Audible alarm
6 7 RF Zone Supervision Options Keypad/Bus Module Supervision Options
OFF OFF Disabled Disabled
OFF ON Trouble only Trouble only
ON OFF When disarmed: trouble only; when armed: follow zone’s alarm type Trouble only
ON ON When disarmed: audible alarm; when armed: follow zone’s alarm type Audible alarm

* Tamper recognition of keypad/bus module, only if section [700], option 7, is enabled.

General Zone Options

Table 57: Description of section [706]

Option Description OFF ON

1 Check-in supervision time  24 hours  80 minutes

Section [706]

2 EOL resistors (applies to all hardwired zones – panel, keypad, ZX8/ZX82)  Disabled Enabled
3 Zone input 1 becomes a two-wire smoke input  Disabled  Enabled
4 ZX8/ZX82 ID A (panel + 1) input 1  Zone input  Tamper input
5 ZX8/ZX82 ID B (panel + 9) input 1  Zone input  Tamper input
6 ZX8/ZX82 ID C (panel + 17) input 1  Zone input  Tamper input

= Default

Miscellaneous System Options

Table 58: Description of section [708]

Option Description OFF ON

1 Enter code to view trouble  One-touch  Enter code
EN50131 OPTIONS


Section [708]

2 Enter code to view alarm in memory/event list  One-touch Enter code

3 Trouble latch  Disabled  Enabled
4 Bell squawk on Installer in  Disabled  Enabled
5 Acknowledge trouble(s) before arming  Disabled  Enabled
6 Do not arm if zone opens during exit delay  Disabled  Enabled
7 Disable ‘Bypass and Arm’  Disabled  Enabled

8 Future use - - - -

= Default

Unlock Panel Serial Ports

Enter section [300] to unlock your SP+’s panel serial ports for use with third-party devices using a TM70/TM50 Touch keypad and the K32LCD+. For a step-by-step
procedure, refer to the Insite Gold Installer Menu Guide.

System Timers

Worksheet 54: System Timers

Section Data Description Section Data Description
Remote panic disarm lock delay
[710] ___/___/___ 000 to 255 seconds Entry delay 1* (default: 045) [718] ___/___/___ 000 to 255 seconds (default: 000)
Closing delinquency delay
[711] ___/___/___ 000 to 255 seconds Entry delay 2* (default: 045) [719] ___/___/___ 000 to 255 days (default: 000)
Auto-zone shutdown counter
[712] ___/___/___ 000 to 015 (default: 005) [720] ___/___/___ 000 to 255 seconds Flex-instant delay (default: 015)
For StayD: re-arm delay
[713] ___/___/___ 000 to 255 seconds Intellizone delay (default: 048) [721] ___/___/___ 000 to 255 seconds (default: 005)
Auto trouble shutdown**
[714] ___/___/___ 000 to 255 minutes Recycle alarm delay (default: 000) [722] ___/___/___ 000 to 255 seconds (default: 010)

63
 SP+ Series Programming Guide

Worksheet 54: System Timers

Section Data Description Section Data Description
Recycle alarm counter Panic shutdown**
[715] ___/___/___ 000 to 255 (default: 000) [723] ___/___/___ 000 to 255 seconds (default: 010)
* For EN 50131, the maximum value is 45 seconds.
** For EN 50131, the section must be set to a minimum of 3 and a maximum of 10

Keypad Lockout
Use the following section to program keypad lockout settings for your SP+ control panel. Use worksheet 30 to record your settings.

Worksheet 55: Keypad Lockout

Section Data Description Default
[716] ___/___/___ 000 to 255 minutes Keypad lockout delay 015 minutes
[717] ___/___/___ 000 to 255 attempts before locking Keypad lockout counter 005 attempts
NOTE: For EN 50131, the keypad lockout value must be set between three and ten attempts. The minimum delay to lock must be two minutes.

Dialer Options
Table 59: Description of section [801]

Option Description OFF ON

1 Report system disarming  Always  After alarm
2 Report zone restore on closure  Bell cutoff  Zone closure
Section [801]

3&4 Auto-test report transmission  Disabled  Enabled

5 Contact ID override  Disabled  Enabled
6 Future use
7 Future use
8 Future use

= Default

Timers
Use worksheet 38 to record your settings for sections [820] to [840].

Worksheet 56: Communication Timers

Section Data Description Default
[820] ___/___/___ 000 to 255 hours Fail to comm. clear event timer 000 = disabled
[830] ___/___/___ 000 to 255 x 2 seconds TLM fail delay (landline only) 016
[831] ___/___/___ 000 to 032 Maximum dialing attempts monitoring station (landline only) 002
[832] ___/___/___ 000 to 127 seconds Delay between dialing attempts* (landline only) 020
[833] ___/___/___ 000 to 255 seconds Delay alarm transmission 000
[838] ___/___/___ 000 to 255 seconds Recent closing delay 000
[839] ___/___/___ 000 to 255 minutes Power failure report delay** 015
[840] ___/___/___ 000 to 255 days Auto test report (see table 36 on page 41) 001
* Also applicable when using a VDMP3 Plug-in Voice Dialer.s
**The maximum value for power failure is 60 minutes.

64
SP+ Series Programming Guide

Notes

65
 SP+ Series Programming Guide

66
The whole Paradox team wishes you a successful and easy installation. We hope this product performs to your complete satisfaction.
Should you have any questions or comments, please contact us at [email protected].
Additional information can be found on our website www.paradox.com/support

Printed in Canada - 06/2022 PARADOX.COM SP+030-EP00