32-Zone Wireless Transceiver Security Systems

MG5050 Version 4.75

4 to 32-Zone Expandable Security Systems

SP5500 • SP6000
Version 4.99

Programming Guide
Warranty
For complete warranty information on this product please refer to the Limited Warranty Statement found on our Web site: www.paradox.com. Your use of this Paradox product signifies
your acceptance of all warranty terms and conditions.

Limitations of Alarm Systems

It must be understood that while your Paradox alarm system is highly advanced and secure, it does not offer any guaranteed protection against burglary, fire or other emergency (fire and
emergency options are only available on certain Paradox models). This is due to a number of reasons, including by not limited to inadequate or improper installation/positioning, sensor
limitations, battery performance, wireless signal interruption, inadequate maintenance or the potential for the system or telephone lines to be compromised or circumvented. As a result,
Paradox does not represent that the alarm system will prevent personal injury or property damage, or in all cases provide adequate warning or protection.

Your security system should therefore be considered as one of many tools available to reduce risk and/or damage of burglary, fire or other emergencies, such other tools include but are
not limited to insurance coverage, fire prevention and extinguish devices, and sprinkler systems.
We also strongly recommend that you regularly maintain your security systems and stay aware of new and improved Paradox products and developments.
TBR-21: In order to comply with TBR-21, standard force dialing must be enabled.

CAUTION: The user is cautioned that any changes or modifications not expressly approved by Paradox Security Systems could void the user’s authority to operate/use the equipment. This
device complies with Industry Canada licence-exempt RSS standards). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device
must accept any interference, including interference that may cause undesired operation of the device.
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil
ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le
fonctionnement.
This Class B digital apparatus complies with Canadian ICES-003. Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.
This device complies with part 15 of the FCC Rules. Operation is subject to the following twoconditions: (1) This device may not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause undesired operation.

UL And ULC Warnings

This equipment has the capability of being programmed with features not verified for use in UL installations. To stay within UL and ULC standards, the installer should use the following
guidelines when configuring the system:
• All components of the system should be UL listed for the intended application.
• If used for fire detection, the installer should refer to NFPA Standards #72, Chapter 2. In addition, once installation is complete, the local fire authority must be notified of the
installation.
• WARNING: This equipment must be installed and maintained by qualified service personnel only
• This equipment must be verified by a qualified technician once every three years.
• All keypads must use an anti-tamper switch.
• Do not bypass fire zones.
• Maximum allowed entry delay is 45 seconds.
• Maximum allowed exit delay is 60 seconds.
• Minimum 4 minutes for bell cut-off time.
• The following features do not comply with UL requirements: Bypass Recall and Auto Trouble Shutdown.
• Do not connect the primary indicating device to a relay. The installer must use the bell output.
• To comply with UL985, the auxiliary power output should not exceed 200mA.
• Do not connect the zone ground terminal with UL Listed products.
• The metallic enclosure must be grounded to the cold water pipe.
• All outputs are Class 2 or power-limited, except for the battery terminal. The Class 2 and power-limited fire alarm circuits shall be installed using CL3, CL3R, CL3P, or substitute cable
permitted by the National Electrical Code, ANSI/NFPA 70.
• EOL resistor part #2011002000
• For UL Installations: Universal UB1640W 16.5 Vac min 40 VA
• All outputs are rated from 11.3 Vdc to 12.7 Vdc
• 12 Vdc 4 Ah rechargeable acid/lead or gel cell backup battery (YUASA model #NP7-12 recommended) for residential use. Use a 7 Ah battery to comply with fire requirements.
• Wheelock 46T-12 siren

© 2014 Paradox Ltd. All rights reserved. Specifications may change without prior notice. One or more of the following US patents may apply: 7046142, 6215399, 6111256, 6104319,
5920259, 5886632, 5721542, 5287111, 5119069, 5077549 and RE39406. Canadian and international patents may also apply. Magellan, Spectra SP, and BabyWare are trademarks or
registered trademarks of Paradox Ltd. or its affiliates in Canada, the United States and/or other countries.
Things You Need to Know
About this Programming Guide
Use this programming guide to record programmed settings for your Magellan or Spectra SP control panel. This programming
guide should be used along with the Magellan and Spectra SP Reference & Installation Manual (available online), whenever
installing or programming your Magellan or Spectra SP system.
Conventions
The following typographical conventions are used throughout this guide:

Default Settings: Values which appear in bold typeface signify the default value: e.g., : Installer Quick Menu (indicates that information on the topic can
Access code length:  6 digits  4 digits (4 digits is the default value) also be found in the Installer Quick Menu on page 7)

Section numbers and keypad keys also appear in bold typeface, enclosed by WARNING: Important information
brackets: e.g., Section [706] must be enabled...

Throughout this guide, Magellan (MG) and Spectra (SP) will be referred to as MG/SP NOTE: Suggestion or reminder

Installer Code
The default installer code is 0000 or 000000. This code allows you to enter programming mode, where you can program all
features, options, and commands of the control panel, except for user codes. To change this code, see System Codes on page 30.
Maintenance Code
Similar to the installer code, the maintenance code allows you to enter programming mode and program all sections, except for
user codes and communication settings (sections [395], [397], [398], [815], [816], [817], [910], [911], [970], [918], [919], [920] to
[927], [929] to [935], [936] to [942], [943] to [949], and [975]) – these sections can only be accessed using the installer code. Since
there is no default code, see System Codes on page 30 to set a default.
System Master Code
The default system master code is 1234 or 123456. The system master code allows you to utilize any arming method, as well as
program user codes. To change the default code, see System Codes on page 30.
Panel Reset
Performing a panel reset will reset all panel settings to their preset, default values.
SP4000 / SP65 panels
To perform a panel reset for a SP4000 or SP65 control panel, proceed as follows:
1. Verify that the installer lock is disabled.
2. Remove the battery and AC power from the control panel.
3. Remove all connected wires and devices from the PG1 and zone 1 terminals.
4. Using a wire, short the PG1 and zone 1 terminals.
5. Reconnect the AC and battery power to the panel. Once connected, the following will occur: 1) STATUS LED flashes; 2) STATUS
LED remains illuminated, indicating a reset is in progress; 3) STATUS LED flashes, indicating the reset is complete.
6. Remove the jumper wire.
All other MG/SP panels
To perform a panel reset for all other MG/SP panels:
1. Press and hold the panel’s RESET button until the STATUS LED flashes (5 seconds).
2. Release the RESET button, and then push it once more, within two seconds.
To reset the panel to its default settings using section programming, see section [950] in Usability Sections, on page 53.
Entering Programming Mode
To enter programming mode, proceed as follows:
1. Press ENTER.
2. Enter your installer or maintenance code. Upon entering your code, the ARM and STAY LEDs will flash. To modify codes, see
System Codes on page 30.
3. Enter the three-digit section you wish to program. The ARM and STAY LEDs remain illuminated.
4. Enter required data.
WARNING: To enter programming mode, all zones must be disarmed and StayD mode deactivated. To deactivate StayD,
press OFF, enter your master or user code, and then press OFF.

Things You Need to Know | 3

Data Entry and Display
To access the data display mode, access the desired section and press ENTER before entering any data. Depending on the keypad(s)
configured to your system, specific LEDs or icons will flash, thus indicating that you are in data display mode. Each time ENTER is
pressed, the keypad will display the next digit in the current section, and will continue to do so through all the remaining sections,
one digit at a time, without changing the programmed values; this is not available for sections using the multiple feature select
method. Press CLEAR at any time, to exit data display mode.
There are two methods that can be used to enter data when in programming mode: single digit data entry and feature select
programming.
Single Digit Data Entry Method
After entering programming mode, some sections will require you to enter decimal values from 000 to 255. Other sections will
require that you enter hexadecimal values from 0 to F. The required data will be clearly indicated in this guide. When entering the
final digit in a section, the panel will automatically save and advance to the next section. See Decimal and Hexadecimal
Programming for details on the various keys, and their equivalent decimal and hexadecimal values.
Feature Select Programming Method
After entering certain sections, eight options will be displayed. In these instances, each option (from 1 to 8) represent a specific
feature. To turn enable the option, press the key corresponding to the desired option. Press the key again to remove the digit,
thereby, disabling the option. Press SLEEP to disable all eight options. When the options are set, press ENTER to save your settings
and advance to the next section.

Viewing Version Numbers

Table 1: Viewing panel and keypad version numbers

Step Action Details When Viewing Keypad Version

Enter viewing mode: The first digit is displayed Digit 1: ARM is illuminated
• For panel version, enter section [980] (usually 0)
1
• For keypad version, enter installer programming,
then press and hold ARM
2 Press ENTER The second digit is displayed Digit 2: SLEEP is illuminated
3 Press ENTER The third digit is displayed Digit 3: STAY is illuminated
4 Press ENTER The fourth digit is displayed Digit 4: OFF is illuminated

Example: Version 01.42

Digits 1-4

NOTE: For keypads K10V/H and K636, the keypad version numbers cannot be viewed.

Decimal and Hexadecimal Programming

Table 2: Decimal and hexadecimal values for 10 and 32-Zone LED keypads

Result
Value or Action Key
32-Zone LED 10-Zone LED
Value 0/replace current
SLEEP Erase digit and remain in section Erase digit and remain in section
digit with 0
Values 1 to 9 1 to 9 Zone 1 to 9 Keys 1 to 9
A (hex only) 0 Zone 10 Key 0 (10)
B (hex only) OFF Zone 11 OFF

C (hex only) BYP Zone 12 BYP

D (hex only) MEM Zone 13 MEM

E (hex only) TBL Zone 14 TBL

F (hex only) Zone 15

Exit without saving CLEAR Arm and Stay LEDs flash Arm and Stay LEDs flash
Save data (hex only) ENTER Advances to next section Advances to next section

4 | Things You Need to Know

Contents Description of Sections [700] to [704] ...................................37
Zone Options ...........................................................................38
Installer Quick Menu .................................................................7 ATZ Options ................................................................................................................................. 38
Zones ............................................................................................................................................... 7 General Zone Options ............................................................................................................... 38
Delays ............................................................................................................................................. 7 Miscellaneous System Options ............................................................................................... 39
Time and Date .............................................................................................................................. 7 System Timers .........................................................................39
Walk Test Mode ............................................................................................................................ 7
Keypad Lockout .......................................................................39
Installer and Maintenance Codes ............................................................................................ 7
WinLoad/BabyWare .................................................................................................................... 7 Programming the Daylight Savings Feature ........................39
Monitoring Phone Number ....................................................................................................... 7 Country Codes ............................................................................................................................ 40
Communicator ............................................................................................................................. 8 Customized Daylight Savings Features ................................................................................ 40
Cancel Communication ............................................................................................................. 8 Partition Programming ..........................................................40
Keypad Programming ................................................................................................................ 8
Partition Options ....................................................................................................................... 40
PGMs ............................................................................................................................................... 8
Partition Timers ....................................................................................................................... 41
System Planning ........................................................................9 Partition Labels .......................................................................................................................... 41
Bus Module Planning .................................................................................................................. 9 SMS and Bus Module Programming ......................................41
Wireless Keypad Planning ........................................................................................................ 10
SMS Site Name ............................................................................................................................ 41
Wireless Siren Planning ............................................................................................................ 10
Bus Module Labels ..................................................................................................................... 41
Programmable Output (PGM) Planning .............................................................................. 11
Wireless Repeater Planning ..................................................................................................... 11 Communication Programming ..............................................42
Zone Planning ............................................................................................................................ 11 Dialer Options ............................................................................................................................. 42
Event Call Direction Options ................................................................................................... 43
Zone Recognition ................................................................... 13
GSM Options ............................................................................................................................... 43
MG Series ...................................................................................................................................... 13
IP/GPRS Options ......................................................................................................................... 43
SP Series ........................................................................................................................................ 14
Report Codes and Partition Accounts ................................................................................... 44
Zone Definitions ................................................................... 16 Landline and GSM Communication ...................................................................................... 44
Custom Zone Definitions ......................................................................................................... 18 Timers ........................................................................................................................................... 44
Zone Timers ............................................................................ 18 VDMP3 Options .......................................................................................................................... 44
Test Report and Report Delays ............................................................................................... 45
MG Series ...................................................................................................................................... 18
GSM Settings ............................................................................................................................... 45
SP Series ........................................................................................................................................ 18
System and Communication Report Codes ..........................45
Wireless Zone Assignment .................................................... 19
Entering Report Codes .............................................................................................................. 45
Wireless Transmitter Signal Strength .................................................................................... 19
Special Arming and Disarming Report Codes .................................................................... 45
Zone Report Codes and Labels .............................................. 19 Special Alarm Report Codes .................................................................................................... 45
Zone Report Codes ..................................................................................................................... 19 System Trouble Report Codes ................................................................................................. 46
Zone Labels ................................................................................................................................. 20 System Trouble Restore Codes ................................................................................................ 46
Programmable Output Programming ................................ 20 System Special Report Codes .................................................................................................. 46
Programmable Output Recognition ................................................................................... 20 Installer Function Keys .............................................................................................................. 46
Description of MG/SP Events ................................................................................................... 21 Contact ID Report Codes .......................................................................................................... 47
PGM Activation/Deactivation Events ................................................................................... 27 Automatic Report Codes .......................................................................................................... 49
PGM Options ............................................................................................................................. 28 Communication Report Codes ............................................................................................... 51
PGM Delays ................................................................................................................................. 29 Communication Restore Report Codes ................................................................................ 51
PGM Serial Numbers .................................................................................................................. 29 Software Options and Additional Timers ..............................51
Wireless PGM Signal Strength ................................................................................................. 29 Additional Communication Timers ....................................................................................... 51
PGM Labels .................................................................................................................................. 29 WinLoad/BabyWare Options .................................................................................................. 52
User Programming ............................................................... 30 IP and Software Configurations .............................................52
System Codes .............................................................................................................................. 30 IP Account Numbers .................................................................................................................. 52
User Code Options ..................................................................................................................... 30 Software and PCS Connection Settings ............................................................................. 52
User Report Codes ...................................................................................................................... 31 IP Receiver Configurations ....................................................................................................... 52
User Labels ................................................................................................................................... 31
Usability Sections ....................................................................53
Wireless Repeater Programming (RPT1) .............................. 31 Description of Sections [950], [955], and [960] ................................................................... 53
Wireless Repeater Assignment ................................................................................................ 31 Description of Section [965] .................................................................................................... 53
Wireless Repeater Signal Strength ......................................................................................... 32 Description of Sections [966] and [967] ............................................................................... 54
Wireless Repeater Options ....................................................................................................... 32 Description of Sections [970], [975], and [980] ................................................................... 54
Wireless Repeater Labels .......................................................................................................... 33
Label Programming with LCD Keypads .................................54
Wireless Keypad Programming ............................................. 33 Function keys .............................................................................................................................. 54
Automatic Wireless Keypad Assignment .............................................................................. 33 Catalogues of Special Characters .......................................................................................... 55
Compatibility Check (K37 only) .............................................................................................. 33 Keypad Letter Assignments ..................................................................................................... 56
Standard Wireless Keypad Assignment ................................................................................ 33
Trouble Display .......................................................................56
Wireless Keypad, Repeater, and Siren Options ................................................................... 33
Wireless Keypad Signal Strength ............................................................................................ 34 Product Compatibility Chart ..................................................58
Wireless Keypad Labels ............................................................................................................. 34 Hardware Connections ...........................................................59
Remote Control Programming .............................................. 34 Single Zone Inputs ..................................................................................................................... 59
Remote Control Button Assignment ..................................................................................... 34 Advanced Technology Zone (ATZ) Connections ................................................................ 59
User Assignment for Remote Controls ................................................................................ 36 Connecting Fire Circuits ........................................................................................................... 60
Wireless Siren Programming ................................................. 36 Alarm Relay and PGM Connections ...................................................................................... 60
AC Power & Backup Battery Connections ............................................................................ 60
Wireless Siren Assignment ....................................................................................................... 36
Demonstration or Emergency System Power-up without an AC Source ..................... 60
Wireless Siren Signal Strength ................................................................................................ 36
Wireless Siren Labels ................................................................................................................. 36
Cancelling the Tamper Supervision for Wireless Sirens .................................................... 37

Contents | 5
PCB Layouts/Wiring Diagrams .............................................. 61
MG5000 ........................................................................................................................................ 61
MG5050 ........................................................................................................................................ 62
SP4000 .......................................................................................................................................... 63
SP5500 .......................................................................................................................................... 64
SP6000 .......................................................................................................................................... 65
SP65 ............................................................................................................................................... 66
SP7000 .......................................................................................................................................... 67
Appendix A ............................................................................. 68
EN 50131 Programming ........................................................................................................... 68
ATZ Options ................................................................................................................................. 68
General Zone Options ............................................................................................................... 69
Miscellaneous System Options ............................................................................................... 69
System Timers ............................................................................................................................. 69
Keypad Lockout .......................................................................................................................... 70
Dialer Options ............................................................................................................................. 70
Timers ........................................................................................................................................... 70
Special notes for MG5050 ........................................................................................................ 70

List of Worksheets
Worksheet 1: Planning Bus Modules................................................................................................. 9
Worksheet 2: Planning Wireless Keypads...................................................................................... 10
Worksheet 3: Planning Wireless Sirens........................................................................................... 10
Worksheet 4: Planning Programmable Outputs......................................................................... 11
Worksheet 5: Planning Wireless Repeaters................................................................................... 11
Worksheet 6: Planning Zones ............................................................................................................ 11
Worksheet 7: Zone Definitions .......................................................................................................... 17
Worksheet 8: Custom Zone Definitions ......................................................................................... 18
Worksheet 9: Zone Timers for the MG Series ............................................................................... 18
Worksheet 10: Zone Timers for the SP Series............................................................................... 18
Worksheet 11: Wireless Zones ........................................................................................................... 19
Worksheet 12: Zone Report Codes .................................................................................................. 19
Worksheet 13: Zone Labels................................................................................................................. 20
Worksheet 14: PGM Activation/Deactivation Events ................................................................ 27
Worksheet 15: PGM Delays ................................................................................................................. 29
Worksheet 16: PGM Serial Numbers................................................................................................ 29
Worksheet 17: PGM Labels.................................................................................................................. 29
Worksheet 18: User System Codes................................................................................................... 30
Worksheet 19: User Code Options ................................................................................................... 30
Worksheet 20: User Report Codes.................................................................................................... 31
Worksheet 21: User Labels .................................................................................................................. 31
Worksheet 22: Wireless Repeater Assignment ............................................................................ 31
Worksheet 23: Wireless Repeater Labels ....................................................................................... 33
Worksheet 24: Wireless Keypad Assignment ............................................................................... 33
Worksheet 25: Wireless Keypad Labels .......................................................................................... 34
Worksheet 26: Programming Remote Controls .......................................................................... 35
Worksheet 27: Wireless Siren Assignment .................................................................................... 36
Worksheet 28: Wireless Siren Labels ............................................................................................... 36
Worksheet 29: System Timers............................................................................................................ 39
Worksheet 30: Keypad Lockout......................................................................................................... 39
Worksheet 31: Daylight Savings Time ............................................................................................ 40
Worksheet 32: Partition Timers ......................................................................................................... 41
Worksheet 33: Partition Labels.......................................................................................................... 41
Worksheet 34: SMS Site Name........................................................................................................... 41
Worksheet 35: Bus Module Labels ................................................................................................... 41
Worksheet 36: Report Codes and Partition Accounts............................................................... 44
Worksheet 37: Landline and GSM Communication Settings ................................................. 44
Worksheet 38: Communication Timers......................................................................................... 44
Worksheet 39: VDMP3 Maximum Attempts................................................................................. 44
Worksheet 40: Test Report and Report Delays ........................................................................... 45
Worksheet 41: GSM Settings (PCS series) ..................................................................................... 45
Worksheet 42: Special Arming and Disarming Report Codes................................................ 45
Worksheet 43: Special Alarm Report Codes ................................................................................. 45
Worksheet 44: Special Trouble Report Codes.............................................................................. 46
Worksheet 45: System Trouble Restore Codes ............................................................................ 46
Worksheet 46: System Special Report Codes............................................................................... 46
Worksheet 47: Communication Report Codes ............................................................................ 51
Worksheet 48: Communication Restore Report Codes ............................................................ 51
Worksheet 49: Additional Communication Timers................................................................... 51
Worksheet 50: WinLoad/BabyWare Options................................................................................ 52
Worksheet 51: IP Account Numbers............................................................................................... 52
Worksheet 52: Software and PCS Connection Settings............................................................ 52
Worksheet 53: IP Receiver 1 Configuration................................................................................... 53
Worksheet 54: IP Receiver 2 Configuration................................................................................... 53
Worksheet 55: IP Receiver Backup Configuration ...................................................................... 53
Worksheet 56: System Timers............................................................................................................ 69
Worksheet 57: Keypad Lockout......................................................................................................... 70
Worksheet 58: Communication Timers......................................................................................... 70

6 | Contents
Magellan & Spectra SP • Programming Guide

Walk Test Mode

Installer Quick Menu Step Action Details

Zones = flash; maintenance code may also be

1 + installer code
used
Step Action Details 2 -
= flash; programmed zones are lit (buttons 3 6 Activates or deactivates walk test mode
1 + installer code or LED, depending on keypad); maintenance
code may also be used Installer and Maintenance Codes
2 Zone number Two digits: 01 to 32
Step Action Details
Wireless zone: open/close cover or press
LEARN/TAMPER switch; 1 + installer code = flash
3 Enroll or erase zone hardwired zone: press ENTER;
2 -
to erase a programmed zone, press and hold
SLEEP for three seconds • 7 for installer
code
See Zone Definitions on page 16, for the zone
4 Zone type 3 • 8 for -
type
maintenance
If applicable, assign the zone to one or both code
Assign partition
5 partitions, and then press ENTER; by default, all
(1 and/or 2 + ENTER) 4 Code Enter a four or six-digit code
zones are assigned to partition 1
5 Confirm code Re-enter the four or six-digit code, to confirm
NOTE: If applicable, partition 2 status LEDs display signal strength of selected
wireless zone (4 LEDs = best signal; 1 LED = weak signal; no LEDs = hardwired NOTE: To erase a code, press and hold SLEEP for three seconds.
panel/keypad zone).
WinLoad/BabyWare

Step Action Details

Delays
1 + installer code = flash
Step Action Details 2 -
= flash; maintenance code may also be 3 9 -
1 + installer code
used Enter PC phone number (up to 32 digits), and
4 Phone # + ENTER
2 - then press ENTER
1 = entry delay 1 Default: 045 sec. 5 Panel ID Enter four-digit panel ID
2 = entry delay 2 Default: 045 sec. 6 PC password Enter four-digit PC password
3
3 = exit delay Default: 060 sec. NOTE: To erase the WinLoad/BabyWare phone number, panel ID, and PC
password, press and hold SLEEP for three seconds.
4 = bell cut-off Default: 004 min.
Entry/exit delay = seconds; Monitoring Phone Number
4 000 to 255
bell cut-off = minutes
Step Action Details
Time and Date
1 + installer code = flash
Step Action Details 2 -
= flash; maintenance code may also be 3 1 -
1 + installer code
used Enter monitoring station phone number (up
4 Phone # + ENTER
2 +5 - to 32 digits), and then press ENTER
3 Time (HH:MM) If HH = 13 or more, go to step 5 5 Partition 1 account # -
4 Time format 1 = 24 hr. format, 2 = AM, 3 = PM • 1 for CID
6 SIA is not supported with GPRS/IP reporting
5 Date (YYYY/MM/DD) Enter the year/month/day • 2 for SIA

NOTE: For SP4000 and SP65 systems, the time format must be entered in 24 7 Partition 2 account # -
hr. format, therefore, omit step 4. NOTE: To erase monitoring phone number, reporting format, and account
numbers, press and hold SLEEP for three seconds.

|7
 Magellan & Spectra SP • Programming Guide

Communicator Keypad Input/Output Configuration (K636 V2.0 and higher)

Step Action Details Step Action Details

= flash; maintenance code may also be 1 ENTER + installer code ARM + STAY = flash
1 + installer code
used Press and hold ENTER
2 ARM + STAY = ON
2 - for three seconds

2 = backup phone # ON = output switches to ground following

3 Option 1 system arming (blue wire, maximum150 mA)
3 = personal phone #1 OFF = input (keypad zone input)
4 = personal phone #2 ON = output N.C.
4 Option 2
3 5 = personal phone #3 - OFF = output N.O.
6 = personal phone #4 NOTE: When configuring as an output, clear the assigned keypad zone first.
7 = personal phone #5
PGMs
8 = pager #
Enter phone number (up to 32 digits), and Step Action Details
then press ENTER to proceed to the next phone = flash; maintenance code may also be
4 Phone # + ENTER 1 + installer code
number, or go to step 5 if option 8 was
used
selected
2 -
Enter pager message, and then press ENTER;
5 Message + ENTER 3 PGM number Two digits: 01 to 16
this step applies only to the pager number
NOTE: To erase a phone number pager message, press and hold SLEEP for Wireless PGM = open/close cover; hardwired
4 Enroll or erase PGM
three seconds. PGM = press ENTER

1 = Follow button or
Cancel Communication
2 = Follow button or
Step Action Details 3 = Follow zone
= flash; maintenance code may also be 4 = Follow alarm
1 + installer code 5 PGM type
used
5 = Follow bell
2 -
6 = Follow arm
Cancels all communication with WinLoad,
3 9 7 = Follow Stay arm
BabyWare, and GSM module
8 = Follow Sleep arm
Keypad Programming 1 = Follow
Assigning Keypad Zone Numbers 2 = 1 sec.
3 = 5 sec.
Step Action Details
4 = 15 sec.
ARM + STAY = flash; maintenance code may If PGM type is 1, 2, 3, or
1 ENTER + installer code 4, enter activation 5 = 30 sec.
also be used
delay
Press and hold for 6 = 1 min.
2 ARM + STAY = ON
three seconds 7 = 5 min.
6
K35, K32, K32LCD, K32LX = two digits: 01 to 8 = 15 min.
3 Zone number + ENTER
32; K636, K10V/H = one digit: 1 to 0 (10)
9 = 30 min.
NOTE: To erase a keypad zone number, press CLEAR, and then ENTER.
If PGM type is 5,
Entry Point Zone Assignment (StayD) proceed to the next -
available PGM
Step Action Details If PGM type is 6, 7, or 8, If system is partitioned, select partition(s), and
enter 1 and/or 2 + then press ENTER to proceed to the next
1 ENTER + installer code ARM + STAY = flash
ENTER available PGM
Press and hold OFF for
2 ARM + STAY = ON If PGM type is 1 or 2,
three seconds 01 to 32 (00 = all remote controls); the control
enter two-digit remote
panel proceeds to the next available PGM
K35, K32RF, K37, K32LCD, K32LX = two digits: control #
01 to 32; K636, K10V/H = one digit: 1 to 0 (10;
If PGM type is 3, enter 01 to 32 (00 = all zones); the control panel
maximum ten zones); the first zone 7
two-digit zone # proceeds to the next available PGM
3 Zone number programmed will be the designated entry
point and will flash; up to three more path If system is partitioned, select partition(s), and
If PGM type is 4, enter 1
zones can be added – these zones will light up then press ENTER to proceed to the next
and/or 2 + ENTER
and remain lit available PGM
4 ENTER Press ENTER to save and exit NOTE: To erase a PGM, press and hold SLEEP for three seconds.

8|
Magellan & Spectra SP • Programming Guide

System Planning
Bus Module Planning
Worksheet 1: Planning Bus Modules
Serial # Sticker Description Path Zone (Entry Point) Path Zone Path Zone Path Zone

Bus Module 1

Bus Module 2

Bus Module 3

Bus Module 4

Bus Module 5

Bus Module 6

Bus Module 7

Bus Module 8

Bus Module 9

Bus Module 10

Bus Module 11

Bus Module 12

Bus Module 13

Bus Module 14

Bus Module 15

NOTE: Paths are only applicable when StayD is enabled.

System Planning | 9
 Magellan & Spectra SP • Programming Guide

Wireless Keypad Planning

Worksheet 2: Planning Wireless Keypads
Serial # Sticker Description Path Zone (Entry Point) Path Zone Path Zone Path Zone

Wireless Keypad
1

Wireless Keypad
2

Wireless Keypad
3

Wireless Keypad
4

Wireless Keypad
5

Wireless Keypad
6

Wireless Keypad
7

Wireless Keypad
8

NOTE: When deleting a wireless keypad (K32RF/K37) from the system, the corresponding StayD path zones will also be deleted.

Wireless Siren Planning

Worksheet 3: Planning Wireless Sirens
Serial # Sticker Description Serial # Sticker Description

Siren 1 Siren 3

Siren 2 Siren 4

10 | System Planning
Magellan & Spectra SP • Programming Guide

Programmable Output (PGM) Planning

Worksheet 4: Planning Programmable Outputs
Serial # Sticker Description Serial # Sticker Description

PGM 1 PGM 9

PGM 2 PGM 10

PGM 3 PGM 11

PGM 4 PGM 12

PGM 5 PGM 13

PGM 6 PGM 14

PGM 7 PGM 15

PGM 8 PGM 16

Wireless Repeater Planning

Worksheet 5: Planning Wireless Repeaters
Serial # Sticker Description Serial # Sticker Description

Repeater 1 Repeater 2

Zone Planning
Worksheet 6: Planning Zones
Arming Method Arming Method
Serial # Sticker Zone # Zone Description Stay Sleep Full Serial # Sticker Zone # Zone Description Stay Sleep Full

Zone l l l Zone l l l

Zone l l l Zone l l l

System Planning | 11
 Magellan & Spectra SP • Programming Guide

Worksheet 6: Planning Zones (Continued)

Arming Method Arming Method
Serial # Sticker Zone # Zone Description Stay Sleep Full Serial # Sticker Zone # Zone Description Stay Sleep Full

Zone l l l Zone l l l

Zone l l l Zone l l l

Zone l l l Zone l l l

Zone l l l Zone l l l

Zone l l l Zone l l l

Zone l l l Zone l l l

Zone l l l Zone l l l

Zone l l l Zone l l l

Zone l l l Zone l l l

Zone l l l Zone l l l

Zone l l l Zone l l l

Zone l l l Zone l l l

Zone l l l Zone l l l

Zone l l l Zone l l l

12 | System Planning
Magellan & Spectra SP • Programming Guide

Zone Recognition
NOTE: For keypad zone programming, see Keypad Programming on page 8.

MG Series
When expanding zones via ZX8, up to three ZX8 modules can be added to the system, and they are identified by the ZX8 three-position jumpers: +1, +9, and +17.
Table 3 displays zone recognition information for MG control panels.
Table 3: Zone recognition information for the MG series

MG5000 (without ATZ) MG5000 (with ATZ) MG5050 (without ATZ) MG5050 (with ATZ)
Type Zone Description Type Zone Description Type Zone Description Type Zone Description

1 Panel input 1 1 Panel input 1A 1 Panel input 1 1 Panel input 1A

Panel
2 Panel input 2 2 Panel input 2A 2 Panel input 2 2 Panel input 2A
Panel
3 Input 1 3 Panel input 1B Panel 3 Panel input 3 3 Panel input 3A
4 Input 2 4 Panel input 2B 4 Panel input 4 4 Panel input 4A
5 Input 3 5 Input 1 5 Panel input 5 5 Panel input 5A
Panel
ZX8 6 Input 4 6 Input 2 6 Input 1 6 Panel input 1B
Jumper
Panel + 1 7 Input 5 7 Input 3 7 Input 2 7 Panel input 2B
8 Input 6 ZX8 8 Input 4 8 Input 3 8 Panel input 3B
Jumper
9 Input 7 9 Input 5 ZX8 9 Input 4 9 Panel input 4B
Panel + 1
Jumper
10 Input 8 10 Input 6 Panel + 1 10 Input 5 10 Panel input 5B
11 Input 1 11 Input 7 11 Input 6 11 Input 1
12 Input 2 12 Input 8 12 Input 7 12 Input 2
13 Input 3 13 Input 1 13 Input 8 13 Input 3
ZX8 14 Input 4 14 Input 2 14 Input 1 ZX8 14 Input 4
Jumper Jumper
Panel + 9 15 Input 5 15 Input 3 15 Input 2 Panel + 1 15 Input 5
ZX8
16 Input 6 Jumper 16 Input 4 16 Input 3 16 Input 6
17 Input 7 Panel + 9 17 Input 5 ZX8 17 Input 4 17 Input 7
Jumper
18 Input 8 18 Input 6 Panel + 9 18 Input 5 18 Input 8
19 Input 1 19 Input 7 19 Input 6 19 Input 1
20 Input 2 20 Input 8 20 Input 7 20 Input 2
21 Input 3 21 Input 1 21 Input 8 21 Input 3
ZX8
22 Input 4 22 Input 2 22 Input 1 ZX8 22 Input 4
Jumper
Jumper
Panel + 23 Input 5 ZX8 23 Input 3 23 Input 2 23 Input 5
Panel + 9
17 Jumper
24 Input 6 24 Input 4 24 Input 3 24 Input 6
Panel + ZX8
25 Input 7 17 25 Input 5 Jumper 25 Input 4 25 Input 7
26 Input 8 26 Input 6 Panel + 26 Input 5 26 Input 8
17
27 - 27 Input 7 27 Input 6 27 Input 1
28 - 28 Input 8 28 Input 7 28 Input 2
ZX8
29 - 29 - 29 Input 8 Jumper 29 Input 3
-
30 - 30 - 30 - Panel + 30 Input 4
- 17
31 - 31 - - 31 - 31 Input 5
32 - 32 - 32 - 32 Input 6

NOTE: If a device is assigned to a zone which is already programmed, a wireless zone will overwrite a keypad/hardwire zone and a keypad zone will overwrite a
hardwire zone.

Zone Recognition | 13
14 | Zone Recognition SP Series
When expanding zones via ZX8, up to three ZX8 modules can be added to the system, and they are identified by the ZX8 three-position jumpers: +1, +9, and +17. Table 4 displays zone recognition information for SP
control panels.
Table 4: Zone recognition information for the SP series

SP4000 (without ATZ) SP4000 (with ATZ) SP5500 (without ATZ) SP5500 (with ATZ) SP6000 (without ATZ) SP6000 (with ATZ)
Type Zone Description Type Zone Description Type Zone Description Type Zone Description Type Zone Description Type Zone Description

1 Panel input 1 1 Panel input 1A 1 Panel input 1 1 Panel input 1A 1 Panel input 1 1 Panel input 1A
2 Panel input 2 2 Panel input 2A 2 Panel input 2 2 Panel input 2A 2 Panel input 2 2 Panel input 2A
Panel
3 Panel input 3 3 Panel input 3A Panel 3 Panel input 3 3 Panel input 3A 3 Panel input 3 3 Panel input 3A
4 Panel input 4 4 Panel input 4A 4 Panel input 4 4 Panel input 4A 4 Panel input 4 4 Panel input 4A
Panel Panel
5 Input 1 5 Panel input 1B 5 Panel input 5 5 Panel input 5A 5 Panel input 5 5 Panel input 5A
Panel
6 Input 2 6 Panel input 2B 6 Input 1 6 Panel input 1B 6 Panel input 6 6 Panel input 6A
7 Input 3 7 Panel input 3B 7 Input 2 7 Panel input 2B 7 Panel input 7 7 Panel input 7A
ZX8
Jumper 8 Input 4 8 Panel input 4B 8 Input 3 8 Panel input 3B 8 Panel input 8 8 Panel input 8A
ZX8 Panel
Panel + 9 Input 5 9 Input 1 Jumper 9 Input 4 9 Panel input 4B 9 Input 1 9 Panel input 1B
1
10 Input 6 10 Input 2 Panel + 10 Input 5 10 Panel input 5B 10 Input 2 10 Panel input 2B
1
11 Input 7 11 Input 3 11 Input 6 11 Input 1 11 Input 3 11 Panel input 3B
ZX8 ZX8
12 Input 8 Jumper 12 Input 4 12 Input 7 12 Input 2 Jumper 12 Input 4 12 Panel input 4B
13 Input 1 Panel + 13 Input 5 13 Input 8 13 Input 3 Panel + 13 Input 5 13 Panel input 5B
1 ZX8 1
14 Input 2 14 Input 6 14 Input 1 Jumper 14 Input 4 14 Input 6 14 Panel input 6B
15 Input 3 15 Input 7 15 Input 2 Panel + 15 Input 5 15 Input 7 15 Panel input 7B
ZX8 1
Jumper 16 Input 4 16 Input 8 16 Input 3 16 Input 6 16 Input 8 16 Panel input 8B
ZX8
Panel + 17 Input 5 17 Input 1 Jumper 17 Input 4 17 Input 7 17 Input 1 17 Input 1
9
18 Input 6 18 Input 2 Panel + 18 Input 5 18 Input 8 18 Input 2 18 Input 2
9
19 Input 7 19 Input 3 19 Input 6 19 Input 1 ZX8 19 Input 3 19 Input 3
ZX8 ZX8
20 Input 8 20 Input 4 20 Input 7 20 Input 2 Jumper 20 Input 4 20 Input 4
Jumper Jumper
Panel +
21 Input 1 Panel + 21 Input 5 21 Input 8 21 Input 3 21 Input 5 Panel + 21 Input 5
ZX8 9
9 1
22 Input 2 22 Input 6 22 Input 1 Jumper 22 Input 4 22 Input 6 22 Input 6
23 Input 3 23 Input 7 23 Input 2 Panel + 23 Input 5 23 Input 7 23 Input 7
ZX8 9
Jumper 24 Input 4 24 Input 8 24 Input 3 24 Input 6 24 Input 8 24 Input 8
ZX8
Panel + 25 Input 5 25 Input 1 25 Input 4 25 Input 7 25 Input 1 25 Input 1
Jumper
17
26 Input 6 26 Input 2 Panel + 26 Input 5 26 Input 8 26 Input 2 26 Input 2
17
27 Input 7 27 Input 3 27 Input 6 27 Input 1 27 Input 3 27 Input 3
ZX8 ZX8 ZX8
28 Input 8 Jumper 28 Input 4 28 Input 7 28 Input 2 Jumper 28 Input 4 Jumper 28 Input 4
ZX8
29 - Panel + 29 Input 5 29 Input 8 Jumper 29 Input 3 Panel + 29 Input 5 Panel + 29 Input 5
17 17 9
30 - 30 Input 6 30 - Panel + 30 Input 4 30 Input 6 30 Input 6
- 17
31 - 31 Input 7 - 31 - 31 Input 5 31 Input 7 31 Input 7
32 - 32 Input 8 32 - 32 Input 6 32 Input 8 32 Input 8
 Table 4: Zone recognition information for the SP series (Continued)

SP65 (without ATZ) SP65 (with ATZ) SP7000 (without ATZ) SP7000 (with ATZ)
Type Zone Description Type Zone Description Type Zone Description Type Zone Description

1 Panel input 1 1 Panel input 1A 1 Panel input 1 1 Panel input 1A

2 Panel input 2 2 Panel input 2A 2 Panel input 2 2 Panel input 2A
3 Panel input 3 3 Panel input 3A 3 Panel input 3 3 Panel input 3A
4 Panel input 4 4 Panel input 4A 4 Panel input 4 4 Panel input 4A
Panel 5 Panel input 5 5 Panel input 5A 5 Panel input 5 5 Panel input 5A
6 Panel input 6 6 Panel input 6A 6 Panel input 6 6 Panel input 6A
7 Panel input 7 7 Panel input 7A 7 Panel input 7 7 Panel input 7A
8 Panel input 8 8 Panel input 8A 8 Panel input 8 8 Panel input 8A
Panel
9 Panel input 9 9 Panel input 9A 9 Panel input 9 9 Panel input 9A
Panel
10 Input 1 10 Panel input 1B 10 Panel input 10 10 Panel input 10A
11 Input 2 11 Panel input 2B 11 Panel input 11 11 Panel input 11A
12 Input 3 12 Panel input 3B 12 Panel input 12 12 Panel input 12A
ZX8
Jumper 13 Input 4 13 Panel input 4B 13 Panel input 13 13 Panel input 13A
Panel + 14 Input 5 14 Panel input 5B 14 Panel input 14 14 Panel input 14A
1
15 Input 6 15 Panel input 6B 15 Panel input 15 15 Panel input 15A
16 Input 7 16 Panel input 7B 16 Panel input 16 16 Panel input 16A
Panel
17 Input 8 17 Panel input 8B 17 Input 1 17 Panel input 1B
18 Input 1 18 Panel input 9B 18 Input 2 18 Panel input 2B
19 Input 2 19 Input 1 19 Input 3 19 Panel input 3B
20 Input 3 20 Input 2 ZX8 20 Input 4 20 Panel input 4B
ZX8 Jumper
Jumper 21 Input 4 21 Input 3 Panel + 21 Input 5 21 Panel input 5B
ZX8
Panel + 22 Input 5 Jumper 22 Input 4 22 Input 6 22 Panel input 6B
9
23 Input 6 Panel + 23 Input 5 23 Input 7 23 Panel input 7B
1
24 Input 7 24 Input 6 24 Input 8 24 Panel input 8B
25 Input 8 25 Input 7 25 Input 1 25 Panel input 9B
26 Input 1 26 Input 8 26 Input 2 26 Panel input 10B
27 Input 2 27 Input 1 27 Input 3 27 Panel input 11B
ZX8
ZX8 28 Input 3 28 Input 2 Jumper 28 Input 4 28 Panel input 12B
Jumper ZX8
29 Input 4 29 Input 3 Panel + 29 Input 5 29 Panel input 13B
Panel + Jumper
Panel + 9
17 30 Input 5 30 Input 4 30 Input 6 30 Panel input 14B
9
31 Input 6 31 Input 5 31 Input 7 31 Panel input 15B
32 Input 7 32 Input 6 32 Input 8 32 Panel input 16B
Zone Recognition | 15

NOTE: If a device is assigned to a zone which is already programmed, a wireless zone will overwrite a keypad/hardwire zone and a keypad
zone will overwrite a hardwire zone.
 Magellan & Spectra SP • Programming Guide

Zone Definitions
NOTE: If a device is assigned to a zone which is already programmed, a wireless zone will overwrite a keypad/hardwire zone and a keypad zone will overwrite a
hardwire zone.
To define zones on your MG/SP control panel:
1. Press ENTER, and then enter your installer code (maintenance code may also be used). The ARM and STAY functions will flash.
2. Enter the three-digit zone number you wish to program (e.g., 001 to 032). The ARM and STAY functions will remain illuminated.
3. Enter a two-digit zone definition, by referring to table 5.
4. Assign a partition, by referring to table 6. By default, all zones are assigned to partition 1.
5. Select or deselect zone options, using buttons 1 to 8 (see tables 7 and 8).
6. Press ENTER to save and proceed to the next zone.
7. Repeat steps 3 to 6 for all remaining zones.
Table 5: Zone definitions for MG/SP panels Table 6: Partition assignment for MG/SP panels

Arming Type Input Value Description

Input Value Description
Stay Arm Sleep Arm Fully Arm 1 Assign to partition 1
00 Disabled (default) - - - 2 Assign to partition 2
01 Entry delay 1 Entry delay 1 Entry delay 1 Entry delay 1 3 Assign to both partitions
02 Entry delay 2 Entry delay 2 Entry delay 2 Entry delay 2 NOTE: When using the K636 keypad, only
partition 1 is available.
03 Entry delay 1 (Full Arm) Not armed Not armed Entry delay 1
04 Entry delay 2 (Full Arm) Not armed Not armed Entry delay 2 Table 7: Zone options for MG/SP panels
05 Follow Follow* Follow* Follow
Input
06 Follow (sleep/full arm) Not armed Follow* Follow Description
Value
07 Follow (full arm) Not armed Not armed Follow 1 Auto zone shutdown
08 Instant Instant* Instant* Instant 2 Bypassable zone
09 Instant (sleep/full arm) Not armed Instant* Instant 3 RF zone supervision
10 Instant (full arm) Not armed Not armed Instant 6 Intellizone
11 Instant fire† - - - 7 Delay alarm transmission
12 Delayed fire† - - - 8 Force zone
13 Instant fire silent† - - - Input Value
Zone Alarm Type
14 Delayed fire silent† - - - 4 5
15 24 hr. buzzer - - - OFF OFF Audible alarm
16 24 hr. burglary - - - OFF ON Pulsed alarm
17 24 hr. hold-up - - - ON OFF Silent alarm
18 24 hr. gas - - - ON ON Report only
19 24 hr. heat - - - NOTE: For additional zone options, see Zone
20 24 hr. water - - - Options on page 38.

21 24 hr. freeze - - -
Table 8: Keyswitch options for MG/SP panels
22 24 hr. panic‡ - - -
Input
23 Follow no pre-alarm - - - Description
Value
24 Instant no pre-alarm - - -
1 -
25 Keyswitch maintain** - - -
2 -
26 Keyswitch momentary** - - -
3 -
33 Instant no pre-alarm (stay/sleep) Instant Instant Not armed
OFF = Disarm; ON = Disarm only
34 Instant no pre-alarm (sleep) Not armed Instant Not armed 4
if Stay/Sleep armed
35 Entry delay 1 (stay/full)/instant Entry delay 1 Instant Entry delay 1 5 Arm only
36 Entry delay 1 (full arm)/instant Instant Instant Entry delay 1 6 Stay arming*
* Flex-instant: zone will follow the delay at section [720] (default is 15 seconds/0 = instant zone). 7 Sleep arming*
** On-board, hardwire, control panel zones only.
8 -
† ZX8 inputs do not support fire zones. For two-wire smoke installations (not supported by SP4000/SP5500/
SP65), these definitions apply to zone 1 input only. Section [706], option 3, must be enabled. For four-wire * Select only one. If all are OFF, keyswitch will
smoke installations, use any panel, on-board zone input. regular arm.
‡ This alarm will follow the panic 1 option (section [702], option 1).

16 | Zone Definitions
 Table 9: Permitted zone definitions for MG/SP panels

Arming Type Arming Type

Input Input
Description Stay Sleep Fully Description Stay Sleep Fully
Value Disarm Value Disarm
Arm Arm Arm Arm Arm Arm
00 Zone disabled     16 24 hr. burglary    
01 Entry delay 1 -    17 24 hr. hold-up    
02 Entry delay 2 -    18 24 hr. gas    
03 Entry delay 1 (Full Arm) - - -  19 24 hr. heat    
04 Entry delay 2 (Full Arm) - - -  20 24 hr. water    
05 Follow -    21 24 hr. freeze    
06 Follow (sleep/full arm) - -   22 24 hr. panic    
07 Follow (full arm) - - -  23 Follow no pre-alarm -   
08 Instant -    24 Instant no pre-alarm -   
09 Instant (sleep/full arm) - -   25 Keyswitch maintain    
10 Instant (full arm) - - -  26 Keyswitch momentary    
11 Instant fire     33 Instant no pre-alarm (stay/sleep) -   -
12 Delayed fire     34 Instant no pre-alarm (sleep) - -  -
13 Instant fire silent     35 Entry delay 1 (stay/full)/instant -   
14 Delayed fire silent     36 Entry delay 1 (full arm)/instant -   
15 24 hr. buzzer    

Worksheet 7: Zone Definitions

Section Zone Description (see tables 3 and 4) Zone Definition Partition Zone Options Section Zone Description (see tables 3 and 4) Zone Definition Partition Zone Options
[001] 1 ________________________ 01 1 1 2 3 4 5 6 7 8 [017] 17 ________________________ ____/____ ______ 1 2 3 4 5 6 7 8
[002] 2 ________________________ 06 1 1 2 3 4 5 6 7 8 [018] 18 ________________________ ____/____ ______ 1 2 3 4 5 6 7 8
[003] 3 ________________________ 09 1 1 2 3 4 5 6 7 8 [019] 19 ________________________ ____/____ ______ 1 2 3 4 5 6 7 8
[004] 4 ________________________ 09 1 1 2 3 4 5 6 7 8 [020] 20 ________________________ ____/____ ______ 1 2 3 4 5 6 7 8
[005] 5 ________________________ 09 1 1 2 3 4 5 6 7 8 [021] 21 ________________________ ____/____ ______ 1 2 3 4 5 6 7 8
[006] 6 ________________________ 09 1 1 2 3 4 5 6 7 8 [022] 22 ________________________ ____/____ ______ 1 2 3 4 5 6 7 8
[007] 7 ________________________ 09 1 1 2 3 4 5 6 7 8 [023] 23 ________________________ ____/____ ______ 1 2 3 4 5 6 7 8
[008] 8 ________________________ 09 1 1 2 3 4 5 6 7 8 [024] 24 ________________________ ____/____ ______ 1 2 3 4 5 6 7 8
[009] 9 ________________________ ____/____ ______ 1 2 3 4 5 6 7 8 [025] 25 ________________________ ____/____ ______ 1 2 3 4 5 6 7 8
[010] 10 ________________________ ____/____ ______ 1 2 3 4 5 6 7 8 [026] 26 ________________________ ____/____ ______ 1 2 3 4 5 6 7 8
[011] 11 ________________________ ____/____ ______ 1 2 3 4 5 6 7 8 [027] 27 ________________________ ____/____ ______ 1 2 3 4 5 6 7 8
[012] 12 ________________________ ____/____ ______ 1 2 3 4 5 6 7 8 [028] 28 ________________________ ____/____ ______ 1 2 3 4 5 6 7 8
[013] 13 ________________________ ____/____ ______ 1 2 3 4 5 6 7 8 [029] 29 ________________________ ____/____ ______ 1 2 3 4 5 6 7 8
[014] 14 ________________________ ____/____ ______ 1 2 3 4 5 6 7 8 [030] 30 ________________________ ____/____ ______ 1 2 3 4 5 6 7 8
[015] 15 ________________________ ____/____ ______ 1 2 3 4 5 6 7 8 [031] 31 ________________________ ____/____ ______ 1 2 3 4 5 6 7 8
Zone Definitions | 17

[016] 16 ________________________ ____/____ ______ 1 2 3 4 5 6 7 8 [032] 32 ________________________ ____/____ ______ 1 2 3 4 5 6 7 8

NOTE: See worksheet 11 on page 19, for assigning wireless zones to your MG/SP control panel.
 Magellan & Spectra SP • Programming Guide

Custom Zone Definitions

With MG/SP control panels you can create up to four custom zone definition templates (use worksheet 8). Custom zone definition templates (sections [033] to
[036]) will overwrite zone definitions 33 to 36 in table 5 on page 16. Modifications can be made in accordance with table 9 (Permitted zone definitions for MG/SP
panels), on page 17.

Worksheet 8: Custom Zone Definitions

Section Description Disarm Stay Arm Sleep Arm Full Arm
[033] Zone definition template 1 00 24 24 00
[034] Zone definition template 2 00 00 24 00
[035] Zone definition template 3 00 01 24 01
[036] Zone definition template 4 00 24 24 01

Zone Timers
Use the following section to program zone timers for your MG/SP control panel. Use worksheets 9 and 10 to record your settings.
NOTE: When both ATZ and EOL are enabled, the zone speed should not be set below 300 msec.

MG Series
Worksheet 9: Zone Timers for the MG Series
Section Zone MG5000 MG5050 Data Description (default: 060)
[041] 1 (Z1) (Z1) 060 (000 to 255) x 10 msec. Speed of hardwire zone 1
[042] 2 (Z2) (Z2) 060 (000 to 255) x 10 msec. Speed of hardwire zone 2
[043] 3 (Z1 ATZ) (Z3) 060 (000 to 255) x 10 msec. Speed of hardwire zone 3
[044] 4 (Z2 ATZ) (Z4) 060 (000 to 255) x 10 msec. Speed of hardwire zone 4
[045] 5 (Z5) 060 (000 to 255) x 10 msec. Speed of hardwire zone 5
[046] 6 (Z1 ATZ) 060 (000 to 255) x 10 msec. Speed of hardwire zone 6
[047] 7 (Z2 ATZ) 060 (000 to 255) x 10 msec. Speed of hardwire zone 7
[048] 8 (Z3 ATZ) 060 (000 to 255) x 10 msec. Speed of hardwire zone 8
[049] 9 (Z4 ATZ) 060 (000 to 255) x 10 msec. Speed of hardwire zone 9
[050] 10 (Z5 ATZ) 060 (000 to 255) x 10 msec. Speed of hardwire zone 10
[051] 11 060 (000 to 255) x 10 msec. Speed of hardwire zone 11
[052] 12 060 (000 to 255) x 10 msec. Speed of hardwire zone 12
[053] 13 060 (000 to 255) x 10 msec. Speed of hardwire zone 13
[054] 14 060 (000 to 255) x 10 msec. Speed of hardwire zone 14
[055] 15 060 (000 to 255) x 10 msec. Speed of hardwire zone 15
[056] 16 060 (000 to 255) x 10 msec. Speed of hardwire zone 16

SP Series
Worksheet 10: Zone Timers for the SP Series
Section Zone SP4000 SP5500 SP6000 SP65* SP7000** Data Description (default: 060)
[041] 1 (Z1) (Z1) (Z1) (Z1) (Z1) 060 (000 to 255) x 10 msec. Speed of hardwire zone 1
[042] 2 (Z2) (Z2) (Z2) (Z2) (Z2) 060 (000 to 255) x 10 msec. Speed of hardwire zone 2
[043] 3 (Z3) (Z3) (Z3) (Z3) (Z3) 060 (000 to 255) x 10 msec. Speed of hardwire zone 3
[044] 4 (Z4) (Z4) (Z4) (Z4) (Z4) 060 (000 to 255) x 10 msec. Speed of hardwire zone 4
[045] 5 (Z1 ATZ) (Z5) (Z5) (Z5) (Z5) 060 (000 to 255) x 10 msec. Speed of hardwire zone 5
[046] 6 (Z2 ATZ) (Z1 ATZ) (Z6) (Z6) (Z6) 060 (000 to 255) x 10 msec. Speed of hardwire zone 6
[047] 7 (Z3 ATZ) (Z2 ATZ) (Z7) (Z7) (Z7) 060 (000 to 255) x 10 msec. Speed of hardwire zone 7
[048] 8 (Z4 ATZ) (Z3 ATZ) (Z8) (Z8) (Z8) 060 (000 to 255) x 10 msec. Speed of hardwire zone 8
[049] 9 (Z4 ATZ) (Z1 ATZ) (Z9) (Z9) 060 (000 to 255) x 10 msec. Speed of hardwire zone 9
[050] 10 (Z5 ATZ) (Z2 ATZ) (Z1 ATZ) (Z10) 060 (000 to 255) x 10 msec. Speed of hardwire zone 10
[051] 11 (Z3 ATZ) (Z2 ATZ) (Z11) 060 (000 to 255) x 10 msec. Speed of hardwire zone 11
[052] 12 (Z4 ATZ) (Z3 ATZ) (Z12) 060 (000 to 255) x 10 msec. Speed of hardwire zone 12
[053] 13 (Z5 ATZ) (Z4 ATZ) (Z13) 060 (000 to 255) x 10 msec. Speed of hardwire zone 13
[054] 14 (Z6 ATZ) (Z5 ATZ) (Z14) 060 (000 to 255) x 10 msec. Speed of hardwire zone 14
[055] 15 (Z7 ATZ) (Z6 ATZ) (Z15) 060 (000 to 255) x 10 msec. Speed of hardwire zone 15
[056] 16 (Z8 ATZ) (Z7 ATZ) (Z16) 060 (000 to 255) x 10 msec. Speed of hardwire zone 16
* For zones 17-18 (ATZ), the zone timer is set to 600 msec.
** For zones 17-32 (ATZ), the zone timer is set to 600 msec.

18 | Zone Timers
Magellan & Spectra SP • Programming Guide

Wireless Zone Serial Numbers

Use the following section to program the wireless zones on your MG/SP control panel. Use worksheet 11 to record your settings.

Worksheet 11: Wireless Zones

Section Zone Wireless Zone (Serial #) Section Zone Wireless Zone (Serial #) Section Zone Wireless Zone (Serial #)
[061] 1 ___/___/___/___/___/___ [072] 12 ___/___/___/___/___/___ [083] 23 ___/___/___/___/___/___
[062] 2 ___/___/___/___/___/___ [073] 13 ___/___/___/___/___/___ [084] 24 ___/___/___/___/___/___
[063] 3 ___/___/___/___/___/___ [074] 14 ___/___/___/___/___/___ [085] 25 ___/___/___/___/___/___
[064] 4 ___/___/___/___/___/___ [075] 15 ___/___/___/___/___/___ [086] 26 ___/___/___/___/___/___
[065] 5 ___/___/___/___/___/___ [076] 16 ___/___/___/___/___/___ [087] 27 ___/___/___/___/___/___
[066] 6 ___/___/___/___/___/___ [077] 17 ___/___/___/___/___/___ [088] 28 ___/___/___/___/___/___
[067] 7 ___/___/___/___/___/___ [078] 18 ___/___/___/___/___/___ [089] 29 ___/___/___/___/___/___
[068] 8 ___/___/___/___/___/___ [079] 19 ___/___/___/___/___/___ [090] 30 ___/___/___/___/___/___
[069] 9 ___/___/___/___/___/___ [080] 20 ___/___/___/___/___/___ [091] 31 ___/___/___/___/___/___
[070] 10 ___/___/___/___/___/___ [081] 21 ___/___/___/___/___/___ [092] 32 ___/___/___/___/___/___
[071] 11 ___/___/___/___/___/___ [082] 22 ___/___/___/___/___/___
NOTE: When assigning wireless zones, either enter the serial number or press TAMPER/LEARN. To delete the serial number, enter 000000.

Wireless Transmitter Signal Strength

The signal strength test for wireless transmitters is performed in sections [101] to [132]; these sections represent zones 1 to 32, respectively. To test the wireless
transmitter strength of your various wireless devices, proceed as follows:
1. Enter the zone’s respective section (e.g., for zone 1, enter section [101]).
2. Press the transmitter’s anti-tamper switch and note the number of beeps which are emitted. As shown in table 10, the number of beeps correspond to a preset
signal strength range.
Table 10: Signal strength indicator for wireless transmitters

Number of Beeps Signal Strength Result

3 8 to 10 Strong signal
2 5 to 7 Average signal
1 1 to 4 Weak signal (relocate)

NOTE: The visual representation of a transmitter’s signal strength is dependent on the type of keypad. For LED keypads, zones 1 through 10 will illuminate,
depending on the signal strength. For instance, a signal strength of 8 will result in zones 1 through 8 to illuminate. For LCD keypads, a ten-level progress bar
composed of arrows will appear, followed by the numeric value. For a signal strength of 8, eight arrows will appear, followed by the number 8.

Zone Report Codes and Labels

Use the following section to program zone report codes and labels on your MG/SP control panel.

Zone Report Codes

Use worksheet 12 to record your settings when programming zone report codes.

Worksheet 12: Zone Report Codes

Alarm Alarm Tamper Tamper Alarm Alarm Tamper Tamper
Section Zone Report Restore Report Restore Section Zone Report Restore Report Restore
Codes Report Codes Codes Report Codes Codes Report Codes Codes Report Codes
[141] 1 FF FF FF FF [157] 17 FF FF FF FF
[142] 2 FF FF FF FF [158] 18 FF FF FF FF
[143] 3 FF FF FF FF [159] 19 FF FF FF FF
[144] 4 FF FF FF FF [160] 20 FF FF FF FF
[145] 5 FF FF FF FF [161] 21 FF FF FF FF
[146] 6 FF FF FF FF [162] 22 FF FF FF FF
[147] 7 FF FF FF FF [163] 23 FF FF FF FF
[148] 8 FF FF FF FF [164] 24 FF FF FF FF
[149] 9 FF FF FF FF [165] 25 FF FF FF FF
[150] 10 FF FF FF FF [166] 26 FF FF FF FF
[151] 11 FF FF FF FF [167] 27 FF FF FF FF
[152] 12 FF FF FF FF [168] 28 FF FF FF FF
[153] 13 FF FF FF FF [169] 29 FF FF FF FF
[154] 14 FF FF FF FF [170] 30 FF FF FF FF
[155] 15 FF FF FF FF [171] 31 FF FF FF FF
[156] 16 FF FF FF FF [172] 32 FF FF FF FF

Wireless Zone Serial Numbers | 19

 Magellan & Spectra SP • Programming Guide

Zone Labels
Use worksheet 13 to record your settings when programming zone labels.

Worksheet 13: Zone Labels

Section Zone Zone Label Section Zone Zone Label
[181] 1 __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__ [197] 17 __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
[182] 2 __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__ [198] 18 __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
[183] 3 __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__ [199] 19 __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
[184] 4 __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__ [200] 20 __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
[185] 5 __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__ [201] 21 __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
[186] 6 __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__ [202] 22 __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
[187] 7 __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__ [203] 23 __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
[188] 8 __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__ [204] 24 __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
[189] 9 __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__ [205] 25 __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
[190] 10 __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__ [206] 26 __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
[191] 11 __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__ [207] 27 __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
[192] 12 __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__ [208] 28 __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
[193] 13 __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__ [209] 29 __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
[194] 14 __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__ [210] 30 __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
[195] 15 __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__ [211] 31 __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
[196] 16 __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__ [212] 32 __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__

Programmable Output Programming

Use the following section to program programmable outputs (PGMs) on your MG/SP control panel.

Programmable Output Recognition

Table 11: Programmable outputs for MG/SP panels

Control Panel
PGM PGM Output
MG5000 MG5050 SP4000 SP5500 SP6000 SP65 SP7000
1 Control panel output 1       
2 Control panel output 2   -    
3 Control panel output 3 -  - -   
4 Control panel output 4 -  - -  - 
5 Control panel relay - - - -  - 
6 ZX8 ID = 1 output       
7 ZX8 ID = 2 output       
8 ZX8 ID = 3 output       -
9 PGM4 relay 1       
10 PGM4 relay 2       
11 PGM4 relay 3       
12 PGM4 relay 4       
13 RTX3/RX1 output 1 - -     
14 RTX3/RX1 output 2 - -     
15 RTX3 output 3 (relay) - -     
16 RTX3 output 4 (relay) Optional Optional Optional Optional Optional Optional Optional

NOTE: A wireless PGM module can be assigned to any PGM. These modules will work in parallel with the control panel output (not applicable to the SP4000).
Programmable Output on the K32LCD/K32LX
The on-board PGM of the K32LCD and K32LX (not programmable) will follow the arm status of any partition, via any arming method, including StayD. This only
applies to versions 5.10 and higher, with an ECO number of J014.

20 | Programmable Output Programming

Magellan & Spectra SP • Programming Guide

Description of MG/SP Events

Table 12: List of events for MG/SP control panels

Event Group Event Group Description Sub-group Sub-group Description

00 Zone OK 01 to 32 Zone number
01 Zone open 99 Any zone number
00 to 01 -
02 Silent alarm
03 Buzzer alarm
04 Steady alarm
05 Pulsed alarm
06 Strobe
07 Alarm stopped
08 Squawk ON (partition 1only)
02 Partition status 09 Squawk OFF (partition 1 only)
10 Ground start (partition 1 only)
11 Disarm partition
12 Arm partition
13 Entry delay started
14 Exit delay started
15 Pre-alarm delay
16 Report confirmation
99 Any partition status event
00 Bell OFF
01 Bell ON
03 Bell status (partition 1 only) 02 Bell squawk arm
03 Bell squawk disarm
99 Any bell status event
00 Telephone line trouble
01 CLEAR + ENTER, or was pressed for 3 secs. (partition 1 only)
02 -
03 Arm in Stay mode
04 Arm in Sleep mode
05 Arm in Force mode
06 Full arm when armed in Stay mode
07 PC fail to communicate (partition 1 only)
08 Utility key 1 pressed (keys 1 and 2; partition 1 only)
09 Utility key 2 pressed (keys 4 and 5; partition 1 only)
10 Utility key 3 pressed (keys 7 and 8; partition 1 only)
11 Utility key 4 pressed (keys 2 and 3; partition 1 only)
06 Non-reportable event 12 Utility key 5 pressed (keys 5 and 6; partition 1 only)
13 Utility key 6 pressed (keys 8 and 9; partition 1 only)
14 Tamper generated alarm
15 Supervision loss generated alarm
16 -
17 -
18 -
19 -
20 Full arm when armed in Sleep mode
21 Firmware upgrade (partition 1 only; non-PGM event)
22 -
23 StayD mode activated
24 StayD mode deactivated

Programmable Output Programming | 21

 Magellan & Spectra SP • Programming Guide

Table 12: List of events for MG/SP control panels (Continued)

Event Group Event Group Description Sub-group Sub-group Description

25 IP registration status change
26 GPRS registration status change
27 Armed with trouble(s)
06 Non-reportable event
28 Supervision alert
(Cont.) (Cont.)
29 Supervision alert restore
30 Armed with remote with low battery
99 Any non-reportable event

Button pressed on remote (see Default Data B, in worksheet 26 01 to 32 Remote control number
08
on page 35) 99 Any remote control number

Button pressed on remote (see Default Data C, in worksheet 26 01 to 32 Remote control number
09
on page 35) 99 Any remote control number

Button pressed on remote (see Default Data D, in worksheet 26 01 to 32 Remote control number
10
on page 35) 99 Any remote control number

Button pressed on remote (see Default Data E, in worksheet 26 01 to 32 Remote control number
11
on page 35) 99 Any remote control number
01 to 32 Zone number
12 Cold start wireless zone
99 Any zone number
01 to 16 Output number
17 to 18 Wireless repeater
13 Cold start wireless module (partition 1 only) 19 to 26 Wireless keypad
27 to 30 Wireless siren
99 Any output number
01 to 32 User number
14 Bypass programming
99 Any user number
01 to 32 User number
15 User code activated output (partition 1 only)
99 Any user number
01 to 32 Zone number
16 Wireless smoke maintenance signal
99 Any zone number
01 to 32 Zone number
17 Delay zone alarm transmission
99 Any zone number
01 to 32 Zone number
18 Zone signal strength weak 1 (partition 1 only)
99 Any zone number
01 to 32 Zone number
19 Zone signal strength weak 2 (partition 1 only)
99 Any zone number
01 to 32 Zone number
20 Zone signal strength weak 3 (partition 1 only)
99 Any zone number
01 to 32 Zone number
21 Zone signal strength weak 4 (partition 1 only)
99 Any zone number
01 to 32 Remote control number
22 Button pressed on remote (see option 5, in table 21 on page 34)
99 Any remote control number
01 to 32 Remote control number
23 Button pressed on remote (see option 6, in table 21 on page 34)
99 Any remote control number
01 to 32 Zone number
24 Fire delay started
99 Any zone number

22 | Programmable Output Programming

Magellan & Spectra SP • Programming Guide

Table 12: List of events for MG/SP control panels (Continued)

Event Group Event Group Description Sub-group Sub-group Description

25 - - -
00 Non-valid source ID
01 WinLoad/BabyWare direct
02 WinLoad/BabyWare through IP module
03 WinLoad/BabyWare through GSM module
04 WinLoad/BabyWare through modem
26 Software access (VDMP3, IP100, WinLoad, BabyWare) 09 IP100 direct
10 VDMP3 direct
11 Voice through GSM module
12 Remote access
13 SMS through GSM module
99 Any software access
00 A bus module was added
01 A bus module was removed
27 Bus module event 02 2-way RF module communication failure
03 2-way RF module communication restored
99 Any bus module event
01 to 32 Zone number
28 StayD pass acknowledged
99 Any zone number
01 to 32 User number
29 Arming with user
99 Any user number
00 Auto-arming (on-time/no movement)
01 Late to close
02 No movement arming
03 Partial arming
30 Special arming
04 Quick arming
05 Arming through WinLoad/BabyWare
06 Arming with keyswitch
99 Any special arming
01 to 32 User number
31 Disarming with user
99 Any user number
01 to 32 User number
32 Disarming after an alarm with user
99 Any user number
01 to 32 User number
33 Alarm cancelled with user
99 Any user number
00 Auto-arm cancelled (on-time/no movement)
01 Disarming through WinLoad/BabyWare
02 Disarming through WinLoad/BabyWare after alarm
03 Alarm cancelled through WinLoad/BabyWare
34 Special disarming 04 Paramedical alarm cancelled
05 Disarm with keyswitch
06 Disarm with keyswitch after an alarm
07 Alarm cancelled with keyswitch
99 Any special disarming
01 to 32 Zone number
35 Zone bypassed
99 Any zone number
01 to 32 Zone number
36 Zone in alarm
99 Any zone number
01 to 32 Zone number
37 Fire alarm
99 Any zone number

Programmable Output Programming | 23

 Magellan & Spectra SP • Programming Guide

Table 12: List of events for MG/SP control panels (Continued)

Event Group Event Group Description Sub-group Sub-group Description

01 to 32 Zone number
38 Zone alarm restore
99 Any zone number
01 to 32 Zone number
39 Fire alarm restore
99 Any zone number
00 Panic non-medical emergency
01 Panic medical (this panic alarm in not UL approved)
02 Panic fire

40 03 Recent closing
Special alarm
04 Global shutdown
05 Duress alarm
06 Keypad lockout (partition 1 only)
99 Any special alarm event
01 to 32 Zone number
41 Zone shutdown
99 Any zone number
01 to 32 Zone number
42 Zone tampered
99 Any zone number
01 to 32 Zone number
43 Zone tamper restore
99 Any zone number

24 | Programmable Output Programming

Magellan & Spectra SP • Programming Guide

Table 12: List of events for MG/SP control panels (Continued)

Event Group Event Group Description Sub-group Sub-group Description

00 -
01 AC failure
02 Battery failure
03 Auxiliary current overload
04 Bell current overload
05 Bell disconnected
06 Clock loss
07 Fire loop trouble
08 Fail to communicate with monitoring station telephone # 1
09 Fail to communicate with monitoring station telephone # 2
11 Fail to communicate with voice report
New trouble (partition 1 only, except sub-group 07, which is for
44 12 RF jamming
both partitions)
13 GSM RF jamming
14 GSM no service
15 GSM supervision lost
16 Fail to communicate IP receiver 1 (GPRS)
17 Fail to communicate IP receiver 2 (GPRS)
18 IP module no service
19 IP module supervision loss
20 Fail to communicate IP receiver 1 (IP)
21 Fail to communicate IP receiver 2 (IP)
22 GSM/GPRS module tamper trouble
99 Any new trouble event
00 Telephone line restored
01 AC failure restore
02 Battery failure restore
03 Auxiliary current overload
04 Bell current overload restore
05 Bell disconnected restore
06 Clock loss restore
07 Fire loop trouble restore
08 Fail to communicate with monitoring station tel. # 1 restore
09 Fail to communicate with monitoring station tel. # 2 restore
11 Fail to communicate with voice report restore
45 Trouble restored 12 RF jamming restore
13 GMS RF jamming restore
14 GSM no service restore
15 GSM supervision lost restore
16 Fail to communicate restore IP receiver 1 (GPRS)
17 Fail to communicate restore IP receiver 2 (GPRS)
18 IP module no service restore
19 IP module supervision loss restore
20 Fail to communicate restore IP receiver 1 (IP)
21 Fail to communicate restore IP receiver 2 (IP)
22 GSM/GPRS module tamper trouble restore
99 Any new trouble restored event

Programmable Output Programming | 25

 Magellan & Spectra SP • Programming Guide

Table 12: List of events for MG/SP control panels (Continued)

Event Group Event Group Description Sub-group Sub-group Description

00 Bus/EBus/wireless module communication fault
01 Tamper trouble
46 Bus/EBus/wireless module new trouble (partition 1 only) 02 Power fail
03 Battery failure
99 Any bus module new trouble event
00 Bus/EBus/wireless module communication fault restore
01 Tamper trouble restore
47 Bus/EBus/wireless module trouble restored (partition 1 only) 02 Power fail restore
03 Battery failure restore
99 Any bus module new trouble restored event
00 System power up
01 Reporting test
02 Software log on
03 Software log off
04 Installer in programming mode
48 Special (partition1 only) 05 Installer exited programming mode
06 Maintenance in programming mode
07 Maintenance exited programming mode
08 Closing delinquency delay elapsed
13 Failed to arm
99 Any special event
01 to 32 Zone number
49 Low battery on zone
99 Any zone number
01 to 32 Zone number
50 Low battery on zone restore
99 Any zone number
01 to 32 Zone number
51 Zone supervision trouble
99 Any zone number
01 to 32 Zone number
52 Zone supervision restore
99 Any zone number
01 to 16 Output
17 to 18 Wireless repeater
53 Wireless module supervision trouble (partition 1 only) 19 to 22 Wireless keypad
27 to 30 Wireless siren
99 Any output number
01 to 16 Output
17 to 18 Wireless repeater
54 Wireless module supervision restore (partition 1 only) 19 to 22 Wireless keypad
27 to 30 Wireless siren
99 Any output number
01 to 16 Output
17 to 18 Wireless repeater
55 Wireless module tamper trouble (partition 1 only) 19 to 22 Wireless keypad
27 to 30 Wireless siren
99 Any output number
01 to 16 Output
17 to 18 Wireless repeater
56 Wireless module tamper restore (partition 1 only) 19 to 22 Wireless keypad
27 to 30 Wireless siren
99 Any output number

26 | Programmable Output Programming

Magellan & Spectra SP • Programming Guide

Table 12: List of events for MG/SP control panels (Continued)

Event Group Event Group Description Sub-group Sub-group Description

01 to 32 User number
57 Non-medical alarm (paramedic)
99 Any user number
01 to 32 Zone number
58 Zone forced
99 Any zone number

59 Zone included 01 to 32 Zone number

Zone included (Cont.) 99 Any zone number
01 to 32 User number
60 Remote low battery
99 Any user number
01 to 32 User number
61 Remote low battery restore
99 Any user number
Follow ARM LED status*:
PGM pulse fast in alarm
PGM pulse fast in exit delay, below 10 sec.
PGM pulse slow in exit delay, over 10 sec.
64 System status (on-board PGMs only) 00 PGM steady ON, if armed
PGM OFF, if disarmed
* This event can be assigned to partition 1 or 2. If assigned to
both partitions, the PGM event will follow the list order above,
with number 1 being the highest priority.

PGM Activation/Deactivation Events

Use worksheet 14 to record your settings for the MG/SP PGM events. See table 12 on page 21, for a list of these events.

Worksheet 14: PGM Activation/Deactivation Events

Partition Partition
Section PGM Event Event Group Sub-group Default Section PGM Event Event Group Sub-group Default
(99 for both) (99 for both)
[220] Activation ___/___ ___/___ ___/___ 02/06/99 [236] Activation ___/___ ___/___ ___/___ 00/00/00
PGM 1 PGM 9
[221] Deactivation ___/___ ___/___ ___/___ 02/11/99 [237] Deactivation ___/___ ___/___ ___/___ 00/00/00
[222] Activation ___/___ ___/___ ___/___ 03/01/01 [238] Activation ___/___ ___/___ ___/___ 00/00/00
PGM 2 PGM 10
[223] Deactivation ___/___ ___/___ ___/___ 03/00/01 [239] Deactivation ___/___ ___/___ ___/___ 00/00/00
[224] Activation ___/___ ___/___ ___/___ 06/01/01 [240] Activation ___/___ ___/___ ___/___ 00/00/00
PGM 3 PGM 11
[225] Deactivation ___/___ ___/___ ___/___ 00/00/00 [241] Deactivation ___/___ ___/___ ___/___ 00/00/00
[226] Activation ___/___ ___/___ ___/___ 09/99/99 [242] Activation ___/___ ___/___ ___/___ 00/00/00
PGM 4 PGM 12
[227] Deactivation ___/___ ___/___ ___/___ 00/00/00 [243] Deactivation ___/___ ___/___ ___/___ 00/00/00
[228] Activation ___/___ ___/___ ___/___ 09/99/99 [244] Activation ___/___ ___/___ ___/___ 09/99/99
PGM 5 PGM 13
[229] Deactivation ___/___ ___/___ ___/___ 00/00/00 [245] Deactivation ___/___ ___/___ ___/___ 00/00/00
[230] Activation ___/___ ___/___ ___/___ 00/00/00 [246] Activation ___/___ ___/___ ___/___ 00/00/00
PGM 6 PGM 14
[231] Deactivation ___/___ ___/___ ___/___ 00/00/00 [247] Deactivation ___/___ ___/___ ___/___ 00/00/00
[232] Activation ___/___ ___/___ ___/___ 00/00/00 [248] Activation ___/___ ___/___ ___/___ 09/99/99
PGM 7 PGM 15
[233] Deactivation ___/___ ___/___ ___/___ 00/00/00 [249] Deactivation ___/___ ___/___ ___/___ 00/00/00
[234] Activation ___/___ ___/___ ___/___ 00/00/00 [250] Activation ___/___ ___/___ ___/___ 00/00/00
PGM 8 PGM 16
[235] Deactivation ___/___ ___/___ ___/___ 00/00/00 [251] Deactivation ___/___ ___/___ ___/___ 00/00/00

Programmable Output Programming | 27

 Magellan & Spectra SP • Programming Guide

PGM Options
Table 13: Description of PGM options

PGM 1 [261] PGM 2 [262] PGM 3 [263] PGM 4 [264] PGM 5 [265] PGM 6 [266] PGM 7 [267] PGM 8 [268]
Option Description
OFF ON OFF ON OFF ON OFF ON OFF ON OFF ON OFF ON OFF ON
1 PGM base time (OFF = sec., ON = min.)        
2 PGM state (OFF = N.O.; ON = N.C.)        
3 PGM supervision (not applicable to SP4000)        
PGM activation mode
4        
(OFF = steady; ON = pulse)
5 PGM pulse once every 30 seconds, if armed        
6 PGM pulse on any alarm        
PGM pulse on any alarm (OFF = partition 1;
7        
ON = partition 2)
Flexible PGM deactivation option
(OFF1 = PGM delay only, two activation
8        
events; ON = PGM delay or deactivation
event, whichever comes first)
PGM 9 [269] PGM 10 [270] PGM 11 [271] PGM 12 [272] PGM 13 [273] PGM 14 [274] PGM 15 [275] PGM 16 [276]
Option Description
OFF ON OFF ON OFF ON OFF ON OFF ON OFF ON OFF ON OFF ON
1 PGM base time (OFF = sec., ON = min.)        
2 PGM state (OFF = N.O.; ON = N.C.)        
3 PGM supervision (not applicable to SP4000)        
PGM activation mode (OFF = steady;
4        
ON = pulse)
5 PGM pulse once every 30 seconds, if armed        
6 PGM pulse on any alarm        
PGM pulse on any alarm (OFF = partition 1;
7        
ON = partition 2)
Flexible PGM deactivation option
(OFF1 = PGM delay only, two activation
8        
events; ON = PGM delay or deactivation
event, whichever comes first)

= Default Setting

1
If a PGM delay is programmed (OFF option), the deactivation event can be used as a second activation event.

28 | Programmable Output Programming

Magellan & Spectra SP • Programming Guide

PGM Timers
Use worksheet 15 to record your settings for the MG/SP PGM delays.

Worksheet 15: PGM Delays

Section PGM PGM Delay Value Default Section PGM PGM Delay Value Default
[281] PGM 1 ___/___/___ (001 to 255 x 1 sec./min.) 000 [289] PGM 9 ___/___/___ (001 to 255 x 1 sec./min.) 000
[282] PGM 2 ___/___/___ (001 to 255 x 1 sec./min.) 000 [290] PGM 10 ___/___/___ (001 to 255 x 1 sec./min.) 000
[283] PGM 3 ___/___/___ (001 to 255 x 1 sec./min.) 005 [291] PGM 11 ___/___/___ (001 to 255 x 1 sec./min.) 000
[284] PGM 4 ___/___/___ (001 to 255 x 1 sec./min.) 002 [292] PGM 12 ___/___/___ (001 to 255 x 1 sec./min.) 000
[285] PGM 5 ___/___/___ (001 to 255 x 1 sec./min.) 002 [293] PGM 13 ___/___/___ (001 to 255 x 1 sec./min.) 002
[286] PGM 6 ___/___/___ (001 to 255 x 1 sec./min.) 000 [294] PGM 14 ___/___/___ (001 to 255 x 1 sec./min.) 000
[287] PGM 7 ___/___/___ (001 to 255 x 1 sec./min.) 000 [295] PGM 15 ___/___/___ (001 to 255 x 1 sec./min.) 002
[288] PGM 8 ___/___/___ (001 to 255 x 1 sec./min.) 000 [296] PGM 16 ___/___/___ (001 to 255 x 1 sec./min.) 000
NOTE: To change the base time (minutes or seconds), see PGM Options on page 28.

Wireless PGM Serial Numbers

Use worksheet 16 to record your settings for the MG/SP PGM serial numbers. To delete a wireless PGM, enter 000000, while in the PGM’s respective section. For
automatic assignment, press the PGM’s anti-tamper switch, while in the PGM’s respective section.

Worksheet 16: PGM Serial Numbers

Section PGM Wireless PGM Serial Number Section PGM Wireless PGM Serial Number
[301] PGM 1 ___/___/___/___/___/___ [309] PGM 9 ___/___/___/___/___/___
[302] PGM 2 ___/___/___/___/___/___ [310] PGM 10 ___/___/___/___/___/___
[303] PGM 3 ___/___/___/___/___/___ [311] PGM 11 ___/___/___/___/___/___
[304] PGM 4 ___/___/___/___/___/___ [312] PGM 12 ___/___/___/___/___/___
[305] PGM 5 ___/___/___/___/___/___ [313] PGM 13 ___/___/___/___/___/___
[306] PGM 6 ___/___/___/___/___/___ [314] PGM 14 ___/___/___/___/___/___
[307] PGM 7 ___/___/___/___/___/___ [315] PGM 15 ___/___/___/___/___/___
[308] PGM 8 ___/___/___/___/___/___ [316] PGM 16 ___/___/___/___/___/___
NOTE: To view a PGM’s serial number, see section [960] in Description of Sections [950], [955], and [960] on page 53.

Wireless PGM Signal Strength

The signal strength for wireless PGMs is visible in sections [321] to [336]; these sections represent PGMs 1 to 16, respectively. To view the signal strength, proceed as
follows:
1. Enter the wireless PGM’s respective section (e.g., for PGM1, enter section [321]).
2. Press the PGM’s anti-tamper switch. As shown in table 14, the number of beeps correspond to a preset signal strength range.
Table 14: Signal strength indicator for wireless PGMs

Number of Beeps Signal Strength Result

3 8 to 10 Strong signal
2 5 to 7 Average signal
1 1 to 4 Weak signal (relocate)

NOTE: The visual representation of a PGM’s signal strength is dependent on the type of keypad. For LED keypads, zones 1 through 10 will illuminate, depending on
the signal strength. For instance, a signal strength of 8 will result in zones 1 through 8 to illuminate. For LCD keypads, a ten-level progress bar composed of arrows
will appear, followed by the numeric value. For a signal strength of 8, eight arrows will appear, followed by the number 8.

PGM Labels
Use worksheet 17 to record your settings for the MG/SP PGM labels. To reset these labels, see Description of Section [965] on page 53.

Worksheet 17: PGM Labels

Section PGM PGM Label Section PGM PGM Label
[341] PGM 1 __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__ [349] PGM 9 __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
[342] PGM 2 __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__ [350] PGM 10 __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
[343] PGM 3 __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__ [351] PGM 11 __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
[344] PGM 4 __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__ [352] PGM 12 __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
[345] PGM 5 __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__ [353] PGM 13 __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
[346] PGM 6 __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__ [354] PGM 14 __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
[347] PGM 7 __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__ [355] PGM 15 __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
[348] PGM 8 __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__ [356] PGM 16 __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
NOTE: For special characters and keypad letter assignments, see Label Programming with LCD Keypads on page 54.

Programmable Output Programming | 29

 Magellan & Spectra SP • Programming Guide

User Programming
Use the following section to program the various user features on your MG/SP control panel.

System Codes
Use worksheet 18 to record your settings for the MG/SP system codes. For access options, see section [701], in table 24 on page 37.
NOTE: The maintenance code cannot access the following sections: [395] (Installer code lock); [397] (Installer code); [398] (Maintenance code); [815] (Monitoring
station telephone number 1); [816] (Monitoring station telephone number 2); [817] (Backup monitoring station telephone); [910] (Panel ID); [911] (PC password);
[970] (Download memory key into panel); [975] (Upload panel into the memory key).
Worksheet 18: User System Codes
Section Data Description Default Setting
[395] ___/___/___ Installer code lock* 000
[397] ___/___/___/___/___/___ Installer code 0000
[398] ___/___/___/___/___/___ Maintenance code -
[399] ___/___/___/___/___/___ System master code 1234
* Enter 147 to lock entire control panel. Once locked, enter any other three-digit combination to unlock.

WARNING: The installer and system master codes may consist of four or six digits (see option 1 of section [701], in table 24 on page 37). The control panel
automatically removes the last two digits of these codes, if the length is changed from six digits to four. However, if the access code length is changed
from four digits to six, the control panel adds the code’s first two digits to the end of the code.

User Code Options

Use worksheet 19 to record your settings for the MG/SP user code options. See table 15 for details on these options.
Table 15: User code options for MG/SP control panels

Option Description

1 Partition 1 access
2 Partition 2 access
3 Bypass programming
4 Stay/Sleep arming
5 Force arming
6 Arm only
7 PGM activation only
8 Duress

WARNING: When section [400] is accessed, the control panel will copy the saved value of that section to all user option sections (sections [404] to [432]).
Worksheet 19: User Code Options
Section User Options Section User Options
[400] Default option 1 2 3 4 5 6 7 8 [417] User 17 1 2 3 4 5 6 7 8
[401] System master 1 2 3 4 5 6 7 8 [418] User 18 1 2 3 4 5 6 7 8
[402] Master 1 1 2 3 4 5 6 7 8 [419] User 19 1 2 3 4 5 6 7 8
[403] Master 2 1 2 3 4 5 6 7 8 [420] User 20 1 2 3 4 5 6 7 8
[404] User 4 1 2 3 4 5 6 7 8 [421] User 21 1 2 3 4 5 6 7 8
[405] User 5 1 2 3 4 5 6 7 8 [422] User 22 1 2 3 4 5 6 7 8
[406] User 6 1 2 3 4 5 6 7 8 [423] User 23 1 2 3 4 5 6 7 8
[407] User 7 1 2 3 4 5 6 7 8 [424] User 24 1 2 3 4 5 6 7 8
[408] User 8 1 2 3 4 5 6 7 8 [425] User 25 1 2 3 4 5 6 7 8
[409] User 9 1 2 3 4 5 6 7 8 [426] User 26 1 2 3 4 5 6 7 8
[410] User 10 1 2 3 4 5 6 7 8 [427] User 27 1 2 3 4 5 6 7 8
[411] User 11 1 2 3 4 5 6 7 8 [428] User 28 1 2 3 4 5 6 7 8
[412] User 12 1 2 3 4 5 6 7 8 [429] User 29 1 2 3 4 5 6 7 8
[413] User 13 1 2 3 4 5 6 7 8 [430] User 30 1 2 3 4 5 6 7 8
[414] User 14 1 2 3 4 5 6 7 8 [431] User 31 1 2 3 4 5 6 7 8
[415] User 15 1 2 3 4 5 6 7 8 [432] User 32 1 2 3 4 5 6 7 8
[416] User 16 1 2 3 4 5 6 7 8
NOTE: The system master, master 1, and master 2 user code options cannot be modified. However, if partitioning is not enabled, the user code options for master 2
will match those of master 1.

30 | User Programming
Magellan & Spectra SP • Programming Guide

User Report Codes

Use worksheet 20 to record your settings for the MG/SP user report codes (the default code is 00/FF). To clear and reset these codes, see Description of Sections
[966] and [967] on page 54.

Worksheet 20: User Report Codes

Section User Arming Disarming/Cancel Alarm Section User Arming Disarming/Cancel Alarm
[471] System master 00 FF [487] User 17 00 FF
[472] Master 1 00 FF [488] User 18 00 FF
[473] Master 2 00 FF [489] User 19 00 FF
[474] User 4 00 FF [490] User 20 00 FF
[475] User 5 00 FF [491] User 21 00 FF
[476] User 6 00 FF [492] User 22 00 FF
[477] User 7 00 FF [493] User 23 00 FF
[478] User 8 00 FF [494] User 24 00 FF
[479] User 9 00 FF [495] User 25 00 FF
[480] User 10 00 FF [496] User 26 00 FF
[481] User 11 00 FF [497] User 27 00 FF
[482] User 12 00 FF [498] User 28 00 FF
[483] User 13 00 FF [499] User 29 00 FF
[484] User 14 00 FF [500] User 30 00 FF
[485] User 15 00 FF [501] User 31 00 FF
[486] User 16 00 FF [502] User 32 00 FF
NOTE: For instructions on formatting report codes, see Entering Report Codes on page 45.

User Labels
Use worksheet 21 to record your settings for the MG/SP user labels. To reset these labels, see Description of Section [965] on page 53.

Worksheet 21: User Labels

Section User User Label Section User User Label
[511] 1 __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__ [527] 17 __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
[512] 2 __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__ [528] 18 __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
[513] 3 __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__ [529] 19 __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
[514] 4 __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__ [530] 20 __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
[515] 5 __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__ [531] 21 __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
[516] 6 __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__ [532] 22 __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
[517] 7 __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__ [533] 23 __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
[518] 8 __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__ [534] 24 __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
[519] 9 __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__ [535] 25 __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
[520] 10 __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__ [536] 26 __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
[521] 11 __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__ [537] 27 __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
[522] 12 __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__ [538] 28 __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
[523] 13 __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__ [539] 29 __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
[524] 14 __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__ [540] 30 __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
[525] 15 __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__ [541] 31 __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
[526] 16 __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__ [542] 32 __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
NOTE: For special characters and keypad letter assignments, see Label Programming with LCD Keypads on page 54.

Wireless Repeater Programming (RPT1)

Use the following section to program the wireless repeaters on your MG/SP control panel.

Wireless Repeater Serial Numbers

Use worksheet 22 to record your settings when assigning wireless repeaters to your MG/SP control panel. To reset wireless repeaters, see Description of Section [965]
on page 53.

Worksheet 22: Wireless Repeater Assignment

Section Description Wireless Repeater Serial Number
[545] Repeater 1 ___/___/___/___/___/___
[546] Repeater 2 ___/___/___/___/___/___
NOTE: For automatic assignment, press the wireless repeater’s anti-tamper switch, while in the repeater’s respective section.

Wireless Repeater Programming (RPT1) | 31

32 | Wireless Repeater Assignment Wireless Repeater Signal Strength
The signal strength for wireless repeaters is visible in sections [548] and [549]; these sections represent repeaters 1 and 2, respectively. To view the signal strength, proceed as follows:
1. Enter the wireless repeater’s respective section (e.g., for repeater 1, enter section [548]).
2. Press the repeater’s anti-tamper switch. As shown in table 16, the number of beeps correspond to a preset signal strength range.
Table 16: Signal strength indicator for wireless repeaters

Number of Beeps Signal Strength Result

3 8 to 10 Strong signal
2 5 to 7 Average signal
1 1 to 4 Weak signal (relocate)

NOTE: The visual representation of a repeater’s signal strength is dependent on the type of keypad. For LED keypads, zones 1 through 10 will illuminate, depending on the signal strength. For instance, a signal strength
of 8 will result in zones 1 through 8 to illuminate. For LCD keypads, a ten-level progress bar composed of arrows will appear, followed by the numeric value. For a signal strength of 8, eight arrows will appear, followed by
the number 8.

Wireless Repeater Options

Table 17: Description of the wireless repeater options

RPT1 [551] RPT2 [561] RPT1 [554] RPT2 [564] RPT1 [557] RPT2 [567]
Option Description Option Description Option Description
OFF ON OFF ON OFF ON OFF ON OFF ON OFF ON
1 Repeat wireless keypad 1 signals   1 Repeat wireless zone 17 signals   1 Repeat wireless two-way PGM 9 signals  
2 Repeat wireless keypad 2 signals   2 Repeat wireless zone 18 signals   2 Repeat wireless two-way PGM 10 signals  
3 Repeat wireless keypad 3 signals   3 Repeat wireless zone 19 signals   3 Repeat wireless two-way PGM 11 signals  
4 Repeat wireless keypad 4 signals   4 Repeat wireless zone 20 signals   4 Repeat wireless two-way PGM 12 signals  
5 Repeat wireless keypad 5 signals   5 Repeat wireless zone 21 signals   5 Repeat wireless two-way PGM 13 signals  
6 Repeat wireless keypad 6 signals   6 Repeat wireless zone 22 signals   6 Repeat wireless two-way PGM 14 signals  
7 Repeat wireless keypad 7 signals   7 Repeat wireless zone 23 signals   7 Repeat wireless two-way PGM 15 signals  
     
Magellan & Spectra SP Programming Guide • Wireless Repeater Programming (RPT1)

8 Repeat wireless keypad 8 signals 8 Repeat wireless zone 24 signals 8 Repeat wireless two-way PGM 16 signals
RPT1 [552] RPT2 [562] RPT1 [555] RPT2 [565]
Option Description Option Description = Default Setting
OFF ON OFF ON OFF ON OFF ON
1 Repeat wireless zone 1 signals   1 Repeat wireless zone 25 signals 
2 Repeat wireless zone 2 signals   2 Repeat wireless zone 26 signals 
3 Repeat wireless zone 3 signals   3 Repeat wireless zone 27 signals 
4 Repeat wireless zone 4 signals   4 Repeat wireless zone 28 signals 
5 Repeat wireless zone 5 signals   5 Repeat wireless zone 29 signals 
6 Repeat wireless zone 6 signals   6 Repeat wireless zone 30 signals 
7 Repeat wireless zone 7 signals   7 Repeat wireless zone 31 signals 
8 Repeat wireless zone 8 signals   8 Repeat wireless zone 32 signals   l

RPT1 [553] RPT2 [563] RPT1 [556] RPT2 [566]

Option Description Option Description
OFF ON OFF ON OFF ON OFF ON
1 Repeat wireless zone 9 signals   1 Repeat wireless two-way PGM 1 signals  
2 Repeat wireless zone 10 signals   2 Repeat wireless two-way PGM 2 signals  
3 Repeat wireless zone 11 signals   3 Repeat wireless two-way PGM 3 signals  
4 Repeat wireless zone 12 signals   4 Repeat wireless two-way PGM 4 signals  
5 Repeat wireless zone 13 signals   5 Repeat wireless two-way PGM 5 signals  
6 Repeat wireless zone 14 signals   6 Repeat wireless two-way PGM 6 signals  
7 Repeat wireless zone 15 signals   7 Repeat wireless two-way PGM 7 signals  
8 Repeat wireless zone 16 signals   8 Repeat wireless two-way PGM 8 signals  
Magellan & Spectra SP • Programming Guide

Wireless Repeater Labels

Use worksheet 23 to record your settings for wireless repeater labels. To reset these labels, see Description of Section [965] on page 53.

Worksheet 23: Wireless Repeater Labels

Section Description Wireless Repeater Label
[568] Repeater 1 __/__/__/__/__/__/__/__/__/__/__/__/__/__/__
[569] Repeater 2 __/__/__/__/__/__/__/__/__/__/__/__/__/__/__
NOTE: For special characters and keypad letter assignments, see Label Programming with LCD Keypads on page 54.

Wireless Keypad Programming

Automatic Wireless Keypad Assignment
After powering-up, the control panel will open a ten-minute window for automatic assignment. To assign a keypad to your MG/SP control panel, press and hold
and BYP for three seconds on the respective keypad. Up to eight wireless keypads can be assigned within this ten-minute period.

Compatibility Check (K37 only)

If the K37 is not compatible with the current MG/SP control panel version, the following trouble will be displayed: [TROUBLE: FLASH] [17: ON]. If this occurs, update
your MG/SP control panel to version 3.2 or higher.

Standard Wireless Keypad Assignment

Use worksheet 24 to record your settings, when assigning wireless keypads to your MG/SP control panel. To assign your wireless keypads, enter the serial number or
press and hold and BYP for three seconds.

Worksheet 24: Wireless Keypad Serial Numbers

Section Description Wireless Keypad Serial Number
[571] Keypad 1 ___/___/___/___/___/___
[572] Keypad 2 ___/___/___/___/___/___
[573] Keypad 3 ___/___/___/___/___/___
[574] Keypad 4 ___/___/___/___/___/___
[575] Keypad 5 ___/___/___/___/___/___
[576] Keypad 6 ___/___/___/___/___/___
[577] Keypad 7 ___/___/___/___/___/___
[578] Keypad 8 ___/___/___/___/___/___

Wireless Keypad, Repeater, and Siren Options

Table 18: Description of section [587]

[587] [587]
Option Description Option Description
OFF ON OFF ON
1 Repeater 1 supervision  5 Wireless siren 3 supervision 
2 Repeater 2 supervision  6 Wireless siren 4 supervision 
3 Wireless siren 1 supervision  8 Live display mode 
4 Wireless siren 2 supervision  = Default

NOTE: To cancel the wireless siren tamper supervision, see Cancelling the Tamper Supervision for Wireless Sirens on page 37.

Wireless Keypad Options

Table 19: Description of section [588]

[588] [588]
Option Description Option Description
OFF ON OFF ON
1 Keypad 1 supervision  5 Keypad 5 supervision 
2 Keypad 2 supervision  6 Keypad 6 supervision 
3 Keypad 3 supervision  7 Keypad 7 supervision 
4 Keypad 4 supervision  8 Keypad 8 supervision 
= Default

Wireless Keypad Programming | 33

 Magellan & Spectra SP • Programming Guide

Wireless Keypad Signal Strength

The signal strength for wireless keypads is visible in sections [591] to [598]; these sections represent keypads 1 through 8, respectively. To view the signal strength,
proceed as follows:
1. Enter the wireless keypad’s respective section (e.g., for keypad 1, enter section [591]).
2. Press on the keypad. As shown in table 20, the number of beeps correspond to a preset signal strength range.
Table 20: Signal strength indicator for wireless keypads

Number of Beeps Signal Strength Result

3 8 to 10 Strong signal
2 5 to 7 Average signal
1 1 to 4 Weak signal (relocate)

NOTE: The visual representation of a keypad’s signal strength is dependent on the type of keypad. For LED keypads, zones 1 through 10 will illuminate, depending
on the signal strength. For instance, a signal strength of 8 will result in zones 1 through 8 to illuminate. For LCD keypads, a ten-level progress bar composed of
arrows will appear, followed by the numeric value. For a signal strength of 8, eight arrows will appear, followed by the number 8.

Wireless Keypad Labels

Use worksheet 25 to record your settings for wireless keypad labels. To reset these labels, see Description of Section [965] on page 53.

Worksheet 25: Wireless Keypad Labels

Section Description Wireless Keypad Label
[599] Keypad 1 __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
[600] Keypad 2 __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
[601] Keypad 3 __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
[602] Keypad 4 __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
[603] Keypad 5 __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
[604] Keypad 6 __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
[605] Keypad 7 __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
[606] Keypad 8 __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
NOTE: For special characters and keypad letter assignments, see Label Programming with LCD Keypads on page 54.

Remote Control Programming

Use the following section to program remote controls for your MG/SP control panel.

Remote Control Button Assignment

Use worksheet 26 on page 35 to record your settings when assigning remote controls to your MG/SP control panel. See table 21 for details on button options for
these remotes.
WARNING: Remote controls which are supported by MG/SP control panels are the following: REM1, REM2, RAC1, RAC2, REM3, and REM15.
Table 21: Button options for MG/SP remote controls (see Decimal and Hexadecimal Programming on page 4)

Option Description Option Description

Sleep Empty/button disabled 8 Panic 1
1 Regular/regular force arming 9 Panic 2
2 Stay/stay force arming A Panic 3
3 - B PGM activation (event group 8)*
4 Sleep/sleep force arming C PGM activation (event group 9)*
5 PGM activation (event group 22)* D PGM activation (event group 10)*
6 PGM activation (event group 23)* E PGM activation (event group 11)*
7 Activate window mode (StayD) F Paramedic alarm
* For descriptions on the event groups, see Description of MG/SP Events on page 21.

NOTE: The disarm button ( ) cannot be modified.

34 | Remote Control Programming

Magellan & Spectra SP Programming Guide • Remote Control Programming Worksheet 26: Programming Remote Controls
REM3 Remote Control REM1/REM2/RAC1/RAC2/REM15

PGM 1 PGM 2 PGM 3 PGM 4 PGM 5 PGM 6 PGM 3 & 4 PGM 5 & 6 +
9 0 X  X+ +
+
Default Data B C D E 5 6 Disabled Disabled Default Data 1 4 C 8
RC # Section RC # Section
All [610] _____ _____ _____ _____ _____ _____ _____ _____ All [610] _____ _____ _____ _____
1 [611] _____ _____ _____ _____ _____ _____ _____ _____ 1 [611] _____ _____ _____ _____
2 [612] _____ _____ _____ _____ _____ _____ _____ _____ 2 [612] _____ _____ _____ _____
3 [613] _____ _____ _____ _____ _____ _____ _____ _____ 3 [613] _____ _____ _____ _____
4 [614] _____ _____ _____ _____ _____ _____ _____ _____ 4 [614] _____ _____ _____ _____
5 [615] _____ _____ _____ _____ _____ _____ _____ _____ 5 [615] _____ _____ _____ _____
6 [616] _____ _____ _____ _____ _____ _____ _____ _____ 6 [616] _____ _____ _____ _____
7 [617] _____ _____ _____ _____ _____ _____ _____ _____ 7 [617] _____ _____ _____ _____
8 [618] _____ _____ _____ _____ _____ _____ _____ _____ 8 [618] _____ _____ _____ _____
9 [619] _____ _____ _____ _____ _____ _____ _____ _____ 9 [619] _____ _____ _____ _____
10 [620] _____ _____ _____ _____ _____ _____ _____ _____ 10 [620] _____ _____ _____ _____
11 [621] _____ _____ _____ _____ _____ _____ _____ _____ 11 [621] _____ _____ _____ _____
12 [622] _____ _____ _____ _____ _____ _____ _____ _____ 12 [622] _____ _____ _____ _____
13 [623] _____ _____ _____ _____ _____ _____ _____ _____ 13 [623] _____ _____ _____ _____
14 [624] _____ _____ _____ _____ _____ _____ _____ _____ 14 [624] _____ _____ _____ _____
15 [625] _____ _____ _____ _____ _____ _____ _____ _____ 15 [625] _____ _____ _____ _____
16 [626] _____ _____ _____ _____ _____ _____ _____ _____ 16 [626] _____ _____ _____ _____
17 [627] _____ _____ _____ _____ _____ _____ _____ _____ 17 [627] _____ _____ _____ _____
18 [628] _____ _____ _____ _____ _____ _____ _____ _____ 18 [628] _____ _____ _____ _____
19 [629] _____ _____ _____ _____ _____ _____ _____ _____ 19 [629] _____ _____ _____ _____
20 [630] _____ _____ _____ _____ _____ _____ _____ _____ 20 [630] _____ _____ _____ _____
21 [631] _____ _____ _____ _____ _____ _____ _____ _____ 21 [631] _____ _____ _____ _____
22 [632] _____ _____ _____ _____ _____ _____ _____ _____ 22 [632] _____ _____ _____ _____
23 [633] _____ _____ _____ _____ _____ _____ _____ _____ 23 [633] _____ _____ _____ _____
24 [634] _____ _____ _____ _____ _____ _____ _____ _____ 24 [634] _____ _____ _____ _____
25 [635] _____ _____ _____ _____ _____ _____ _____ _____ 25 [635] _____ _____ _____ _____
26 [636] _____ _____ _____ _____ _____ _____ _____ _____ 26 [636] _____ _____ _____ _____
27 [637] _____ _____ _____ _____ _____ _____ _____ _____ 27 [637] _____ _____ _____ _____
28 [638] _____ _____ _____ _____ _____ _____ _____ _____ 28 [638] _____ _____ _____ _____
29 [639] _____ _____ _____ _____ _____ _____ _____ _____ 29 [639] _____ _____ _____ _____
30 [640] _____ _____ _____ _____ _____ _____ _____ _____ 30 [640] _____ _____ _____ _____
Programming Remote Controls | 35

31 [641] _____ _____ _____ _____ _____ _____ _____ _____ 31 [641] _____ _____ _____ _____
32 [642] _____ _____ _____ _____ _____ _____ _____ _____ 32 [642] _____ _____ _____ _____
WARNING: When section [610] is accessed, the control panel will copy the saved value of that section to all remote controls.
NOTE: When using an RTX3 with the SP series, the left button on a remote control will, by default, trigger PGM3 onboard the RTX3.
 Magellan & Spectra SP • Programming Guide

User Assignment for Remote Controls

Table 22: User assignment per remote control

Section Description Section Description Section Description Section Description

[651] RC 1 for user 1 [659] RC 9 for user 9 [667] RC 17 for user 17 [675] RC 25 for user 25

[652] RC 2 for user 2 [660] RC 10 for user 10 [668] RC 18 for user 18 [676] RC 26 for user 26

[653] RC 3 for user 3 [661] RC 11 for user 11 [669] RC 19 for user 19 [677] RC 27 for user 27

[654] RC 4 for user 4 [662] RC 12 for user 12 [670] RC 20 for user 20 [678] RC 28 for user 28

[655] RC 5 for user 5 [663] RC 13 for user 13 [671] RC 21 for user 21 [679] RC 29 for user 29

[656] RC 6 for user 6 [664] RC 14 for user 14 [672] RC 22 for user 22 [680] RC 30 for user 30

[657] RC 7 for user 7 [665] RC 15 for user 15 [673] RC 23 for user 23 [681] RC 31 for user 31

[658] RC 8 for user 8 [666] RC 16 for user 16 [674] RC 24 for user 24 [682] RC 32 for user 32

Assigning a Remote Control

1. Enter the remote’s respective section (see table 22).
2. Press any button on the designated remote twice, or manually enter the serial number.
Deleting a Remote Control
1. Enter the remote’s respective section (see table 22).
2. Enter 000000.
NOTE: To view a remote control’s serial number, see section [960] in Description of Sections [950], [955], and [960] on page 53.

Wireless Siren Serial Numbers

Use the following section to program wireless sirens for your MG/SP control panel.

Wireless Siren Assignment

Use worksheet 27 to record your settings when assigning wireless sirens.

Worksheet 27: Wireless Siren Assignment

Section Description Wireless Siren Serial Number Section Description Wireless Siren Serial Number
[683] Siren 1 ___/___/___/___/___/___ [685] Siren 3 ___/___/___/___/___/___
[684] Siren 2 ___/___/___/___/___/___ [686] Siren 4 ___/___/___/___/___/___

Wireless Siren Signal Strength

The signal strength for wireless siren is visible in sections [687] to [690]; these sections represent sirens 1 through 4, respectively. To view the signal strength:
1. Enter the wireless siren’s respective section (e.g., for siren 1, enter section [687]).
2. Note the number of beeps which are emitted. As shown in table 23, the number of beeps correspond to a preset signal strength range.
Table 23: Signal strength indicator for wireless sirens

Number of Beeps Signal Strength Result

3 8 to 10 Strong signal
2 5 to 7 Average signal
1 1 to 4 Weak signal (relocate)

NOTE: The visual representation of a siren’s signal strength is dependent on the type of keypad. For LED keypads, zones 1 through 10 will illuminate, depending on
the signal strength. For instance, a signal strength of 8 will result in zones 1 through 8 to illuminate. For LCD keypads, a ten-level progress bar composed of arrows
will appear, followed by the numeric value. For a signal strength of 8, eight arrows will appear, followed by the number 8.

Wireless Siren Labels

Use worksheet 28 to record your settings for wireless siren labels. To reset these labels, see Description of Section [965] on page 53.

Worksheet 28: Wireless Siren Labels

Section Description Wireless Siren Label Section Description Wireless Siren Label
[691] Siren 1 __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__ [693] Siren 3 __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
[692] Siren 2 __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__ [694] Siren 4 __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
NOTE: For special characters and keypad letter assignments, see Label Programming with LCD Keypads on page 54.

36 | Wireless Siren Serial Numbers

Magellan & Spectra SP Programming Guide • Description of Sections [700] to [704] Cancelling the Tamper Supervision for Wireless Sirens
To cancel tamper supervision, access section [695], and then press ENTER. The tamper supervision is disabled until the cover is replaced or after 30 minutes have elapsed.

Description of Sections [700] to [704]

The following section provides information on sections [700] to [704]. See table 24 for details. For keypad programming instructions, refer to on page 7.
Table 24: Description of sections [700] to [704]

Option Option Type Description OFF ON Option Option Type Description OFF ON

1 Partitioning Partitioning  Disabled Enabled 1 Access code length* 6 digits  4 digits

Access/master code
Battery charging, 350 mA or 700 mA options
2  350 mA 700 mA 2 Lock master code  Disabled Enabled
(not applicable to SP4000 and SP65)
General system options Audible trouble warning (except AC
3  Disabled Enabled 3 Confidential mode  Disabled Enabled
Section [700]

Section [701]
failure)
Keypad options 1**
4 Audible trouble warning on AC failure  Disabled Enabled 4 To exit confidential mode  Enter code Press a key

5 RF jamming supervision RF jamming supervision  Disabled Enabled 5 Confidential mode timer  2 mins. 5 secs.
V2.01 or
6 Exit delay termination  Disabled Enabled 6 REM2 version number REM2 version number V2.00 
General system options higher
7 Tamper supervision on the bus module  Disabled Enabled 7 Display entry delay on LCD keypad Disabled  Enabled
Keypad options 1
8 Future use 8 Display exit delay on LCD keypad Disabled  Enabled

1 Panic 1 Disabled  Enabled 1 One-touch regular arming (also REM3) Disabled  Enabled

2 Panic 2  Disabled Enabled 2 One-touch stay arming (also REM3) Disabled  Enabled
Keypad options 2
3 Panic 3  Disabled Enabled 3 One-touch sleep arming (also REM3) Disabled  Enabled
Section [702]

Section [703]
Panic options
4 Panic 1: report only or audible alarm Report only  Audible 4 One-touch bypass programming Disabled  Enabled

5 Panic 2: report only or audible alarm  Report only Audible 5 Restrict arming on battery failure  Disabled Enabled
Restrict arming on tamper failure (zone
6 Panic 3: report only or audible alarm  Report only Audible 6 Arming/disarming options + bus module + wireless PGM)
 Disabled Enabled

Restrict arming on supervision trouble;

7 Future use 7  Disabled Enabled
wireless zones & PGM + bus module
8 Future use 8 Arm/disarm with VDMP3 Arm/disarm with VDMP3 Disabled  Enabled
Regular arming switches to force
1 Disabled  Enabled = Default
arming
*All numbers from 000000 to 999999 are valid giving a total o f 1,000,000 different possible combinations.
Stay arming switches to stay force
2 Disabled  Enabled **Automatic timed operation that will make indications inaccessible to users without a valid access code.
arming
Arming/disarming options
Sleep arming switches to sleep force
3 Disabled  Enabled
arming
Section [704]

Bell squawk when arm/disarm with

4  Disabled Enabled
remote
Bell squawk when arm/disarm with a
5  Disabled Enabled
keypad
6 Keypad options 3 Beep on exit delay Disabled  Enabled
No exit delay beeps and no bell
7 Disabled  Enabled
squawk, when stay/sleep arm
Wireless Siren Labels | 37

8 Arming/disarming options No exit delay when arm with remote  Disabled Enabled
 Magellan & Spectra SP • Programming Guide

Zone Options
Use the following section to program zone options for your MG/SP control panel.

ATZ Options
Table 25: Description of section [705]

Option Description OFF ON

1 ATZ zone doubling  Disabled Enabled
2 ATZ wiring options Series  Parallel

Section [705]

3
Tamper recognition
4 
5 Generate tamper on bypassed zone 
6 
Supervision options
7 
8 Generate supervision on bypassed zone 

= Default

Table 26: Description of options 3 & 4 and 6 & 7, in section [705]

Option Description
3 4 RF Zone/Hardwired Zone Tamper Recognition Options Keypad/Bus Module Tamper Recognition Options*
OFF OFF Disabled Disabled
OFF ON Trouble only Trouble only
ON OFF When disarmed: trouble only; when armed: follow zone’s alarm type Trouble only
ON ON When disarmed: audible alarm; when armed: follow zone’s alarm type Audible alarm
6 7 RF Zone Supervision Options Keypad/Bus Module Supervision Options
OFF OFF Disabled Disabled
OFF ON Trouble only Trouble only
ON OFF When disarmed: trouble only; when armed: follow zone’s alarm type Trouble only
ON ON When disarmed: audible alarm; when armed: follow zone’s alarm type Audible alarm

* Tamper recognition of keypad/bus module, only if section [700], option 7, is enabled.

General Zone Options

Table 27: Description of section [706]

Option Description OFF ON

1 Check-in supervision time  24 hours 80 minutes

Section [706]

2 EOL resistors (applies to all hardwired zones – panel, keypad, ZX8) Disabled Enabled
3 Zone input 1 becomes a two-wire smoke input (except SP4000, SP5500, and SP65)  Disabled Enabled
4 ZX8 ID A (panel + 1) input 1  Zone input Tamper input
5 ZX8 ID B (panel + 9) input 1  Zone input Tamper input
6 ZX8 ID C (panel + 17) input 1  Zone input Tamper input

= Default

38 | Zone Options
Magellan & Spectra SP • Programming Guide

Miscellaneous System Options

Table 28: Description of section [708]

= Default

System Timers
Use the following section to program system timers on your MG/SP control panel. Use worksheet 29 to record your settings.

Worksheet 29: System Timers

Section Data Description Section Data Description
[710] 030 000 to 255 seconds Entry delay 1 [718] 000 000 to 255 seconds Remote panic disarm lock delay
[711] 030 000 to 255 seconds Entry delay 2 [719] 000 000 to 255 days Closing delinquency delay
[712] 001 000 to 015 Auto-zone shutdown counter [720] 015 000 to 255 seconds Flex-instant delay
[713] 048 000 to 255 seconds Intellizone delay [721] 005 000 to 255 seconds For StayD: re-arm delay
[714] 000 000 to 255 minutes Recycle alarm delay [722] 000 000 to 255 times Auto trouble shutdown
[715] 000 000 to 255 Recycle alarm counter [723] 000 000 to 255 seconds Panic shutdown

Keypad Lockout
Use the following section to program keypad lockout settings for your MG/SP control panel. Use worksheet 30 to record your settings.

Worksheet 30: Keypad Lockout

Section Data Description Default
[716] ___/___/___ 000 to 255 minutes Keypad lockout delay 000
[717] ___/___/___ 000 to 255 attempts before locking Keypad lockout counter 000
NOTE:

Programming the Daylight Savings Feature

Use the following section to program Daylight Savings Time on your MG/SP control panel. Use worksheet 31 to record your settings.
Table 29: Description of section [730]

Section Option Description OFF ON

[730] 1 Daylight savings  Disabled Enabled

= Default

System Timers | 39
 Magellan & Spectra SP • Programming Guide

Country Codes
Table 30 lists countries and their respective codes. This information is required when programming section [731] (see worksheet 31 for details).
Table 30: Country codes for MG/SP control panels

Input Value Country Input Value Country

00 Mexico; St. Johns; Bahamas; Turks and Caicos 10 Chatham
01 Cuba 11 Tonga
02 Brazil 12 Iraq; Syria
03 Chile 13 Israel
04 Falkland Islands 14 Lebanon; Kyrgyzstan
05 Paraguay 15 Palestine
06 European Union; United Kingdom; Greenland 16 Egypt
07 Russia and surrounding countries 17 Namibia
South Australia; Victoria; Australian Capital Territory; New
08 18 Canada; United States
South Wales
09 Tasmania; Lord Howe Island 19 New Zealand

Customized Daylight Savings Features

In addition to using the default Daylight Saving Time (DST) settings in section [731], you can also set a customized DST. In sections [732] and [733], you can
program DST starting and ending periods, respectively. Both these sections recognize five different entries, consisting of two digits each.
All entries must be made in the following order:
1. Month: 01 to 12, where 01 represents January
2. Date: 01 to 31, where 01 represents the first day of the month
3. Day: 00 to 07, where 00 is the default setting and 01 represents Sunday
4. Hours: 00 to 23, where 00 represents 12:00 AM
5. Minutes: 00 only, where 00 represents the top of the hour (e.g., 12:00 AM)
NOTE: If the Day value is set to 00, it is ignored and the DST change will only respect the Date value. If the Day setting is set to a value other than 00 (e.g., 03 for
Tuesday), the DST time change will occur on the first Tuesday following the programmed Date value.
Worksheet 31: Daylight Savings Time
Section Data Description
[731] 08 00 to 99 Country code
[732] 1001010200 Month-date-day-hours-minutes DST staring period
[733] 0401010300 Month-date-day-hours-minutes DST ending period
NOTE: If sections [732] and [733] have been modified, but you want to revert to a standard DST code, change all settings in sections [732] and [733] to 00.

Partition Programming
Use the following section to program partitions on your MG/SP control panel.

Partition Options
Table 31: Description of partition 1 options (section [741])

Option Description OFF ON Option

Description
1 Auto-arm on time  Disabled Enabled 3 4
2 Auto-arm on no movement  Disabled Enabled OFF OFF Regular (default)
Section [741]

See options 3 See options 3

3&4 Auto-arm arming mode OFF ON Sleep
& 4, on right & 4, on right
5 Switch to stay arming, if no entry zone is opened  Disabled Enabled ON OFF Stay
Follow zones become entry delay 2, when delay
6 Disabled  Enabled
zone is bypassed

= Default

40 | Partition Programming
Magellan & Spectra SP • Programming Guide

Table 32: Description of partition 2 options (section [742])

Option Description OFF ON Option

Description
1 Auto-arm on time  Disabled Enabled 3 4
2 Auto-arm on no movement  Disabled Enabled OFF OFF Regular (default)
Section [742]

See options 3 See options 3

3&4 Auto-arm arming mode OFF ON Sleep
& 4, on right & 4, on right
5 Switch to stay arming, if no entry zone is opened  Disabled Enabled ON OFF Stay
Follow zones become entry delay 2, when delay
6 Disabled  Enabled
zone is bypassed

= Default

Partition Timers
Use worksheet 32 to record your settings for partition timers.

Worksheet 32: Partition Timers

Section Data Description Default
[745] ___/___/___ 000 to 255 seconds Partition 1 exit delay 045
[746] ___/___/___ 000 to 255 seconds Partition 2 exit delay 045
[747] ___/___/___ 000 to 255 minutes Partition 1 bell cut-off 004
[748] ___/___/___ 000 to 255 minutes Partition 2 bell cut-off 004
[749] ___/___/___ 000 to 255 x 15 minutes Partition 1 no movement 000
[750] ___/___/___ 000 to 255 x 15 minutes Partition 2 no movement 000
[761] ___/___ : ___/___ HH:MM Auto-arm on time partition 1 00:00
[762] ___/___ : ___/___ HH:MM Auto-arm on time partition 2 00:00
.

Partition Labels
Use worksheet 33 to record your settings for partition labels. To reset these labels, see Description of Section [965] on page 53.

Worksheet 33: Partition Labels

Section Description Partition Label
[771] Partition 1 __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
[772] Partition 2 __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
NOTE: For special characters and keypad letter assignments, see Label Programming with LCD Keypads on page 54.

SMS and Bus Module Programming

Use the following section to program SMS site name and bus module labels on your MG/SP control panel.

SMS Site Name

Use worksheet 34 to record your SMS site name. See worksheet 52 on page 52, for additional communication settings.

Worksheet 34: SMS Site Name

Section Description Name
[780] SMS site name __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__

Bus Module Labels

Use worksheet 35 to record your settings for bus module labels. To reset these labels, see Description of Section [965] on page 53.

Worksheet 35: Bus Module Labels

Section Description Bus Module Label Section Description Bus Module Label
[781] Bus 1 __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__ [789] Bus 9 __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
[782] Bus 2 __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__ [790] Bus 10 __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
[783] Bus 3 __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__ [791] Bus 11 __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
[784] Bus 4 __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__ [792] Bus 12 __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
[785] Bus 5 __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__ [793] Bus 13 __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
[786] Bus 6 __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__ [794] Bus 14 __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
[787] Bus 7 __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__ [795] Bus 15 __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
[788] Bus 8 __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
NOTE: For special characters and keypad letter assignments, see Label Programming with LCD Keypads on page 54.

SMS and Bus Module Programming | 41

 Magellan & Spectra SP • Programming Guide

Communication Programming
Use the following section to program various communication features on your MG/SP control panel. Table 33 lists features available for each MG/SP control panel.
Prioritization of signals and messages are based on a “first in, first out” scheme. Systems meet EN 50136 ATS2 or ATS3 requirements when configured as depicted.
NOTE: For increased security, it is suggested that redundant communication methods be installed.
Table 33: Communication features for MG/SP panels

Control Panel
Communication Feature
MG5000 MG5050 SP4000 SP5500 SP6000 SP65 SP7000
GPRS reporting (PCS series)       
GSM reporting and SMS (PCS series)       
IP reporting (IP100)       
E-mail/monitoring (IP100)       
Patented dialer      - 
Supports VDMP3       

Dialer Options
Table 34: Description of dialer options for landline communication (section [800])

Option Description OFF ON

See options 1 See options 1 Option
1&2 Telephone line monitoring Description
& 2, on right & 2, on right
3 Switch to pulse on fifth attempt  Disabled Enabled 1 2
Section [800]

4 Alternate dial  Disabled Enabled OFF OFF Disabled (default)

5 Force dial (must be enabled to comply with TBR-21) Disabled  Enabled OFF ON Trouble only
When disarmed: trouble only; when
6 DTMF dialing Disabled  Enabled ON OFF
armed: audible only
7 Pulse ratio 1:2  1:1.5 ON ON Silent alarms become audible alarm

8 Reporting* 
Dialer
No dialer = Default
activated

* This option also applies to both landline and GSM communication (see Landline and GSM Communication on page 44).

Table 35: Description of general communication dialer options (section [801])

Option Description OFF ON

1 Report system disarming Always  After alarm
2 Report zone restore Bell cutoff  Zone closure
Section [801]

3&4 Auto-test report transmission See table 36 on page 42 See table 36 on page 42
CID defaults/slow format
5 Contact ID override  Disabled
custom
6 Bell squawk upon alarm report confirmation (SP4000 and SP65 only)  Disabled Enabled
7 Bell squawk upon arming report confirmation (SP4000 and SP65 only)  Disabled Enabled
8 Keypad beeps upon arming report confirmation (SP4000 and SP65 only)  Disabled Enabled

= Default

Table 36: Auto-test report transmission options (section [801])

Option
Description
3 4
Transmit the test report code when the days programmed in section [840] have elapsed, at the time programmed in section
1 OFF OFF
[850] (default).
When disarmed: transmit test report code when the time programmed in section [852] has elapsed. When armed: transmit test
2 OFF ON
report code when the time programmed in section [851] has elapsed.
The control panel will transmit the test report code every hour, on the minute value programmed in section [850] (the last two
3 ON OFF digits); the first two digits of section [850] will be ignored. For example, if 10:25 was programmed into section [850], the test
report code would be transmitted at the 25th minute of every hour, i.e., 11:25, 12:25, etc.

42 | Communication Programming
Magellan & Spectra SP • Programming Guide

Table 36: Auto-test report transmission options (section [801])

The test report code will be transmitted when the conditions in entries 2 or 3 above (option 3 = OFF and option 4 = ON; option 3
4 ON ON
= ON and option 4 = OFF), are met.

Event Call Direction Options

Table 37: Description of event call direction options (sections [802] to [804])

Option Description OFF ON Option Description OFF ON

Call tel. #1/monitoring rcvr. #1 for Call tel. #1/monitoring rcvr. #1 for
1 Disabled  Enabled 1 Disabled  Enabled
arm/disarm report codes tamper/restore report codes
Event Call Direction Options 1

Event Call Direction Options 2

Call tel. #2/monitoring rcvr. #2 for Call tel. #2/monitoring rcvr. #2 for
2 Disabled  Enabled 2 Disabled  Enabled
arm/disarm report codes tamper/restore report codes
Section [802]

Section [803]
Call pager for arm/disarm report Call pager for tamper/restore
3  Disabled Enabled 3  Disabled Enabled
codes report codes
Call tel. #1/monitoring rcvr. #1 for Call tel. #1/monitoring rcvr. #1 for
5 Disabled  Enabled 5 Disabled  Enabled
alarm/restore report codes trouble/restore report codes
Call tel. #2/monitoring rcvr. #2 for Call tel. #2/monitoring rcvr. #2 for
6 Disabled  Enabled 6 Disabled  Enabled
alarm/restore report codes trouble/restore report codes
Call pager for alarm/restore report Call pager for trouble/restore
7  Disabled Enabled 7  Disabled Enabled
codes report codes

1
Call tel. #1/monitoring rcvr. #1 for
Disabled  Enabled = Default
special report codes
Event Call Direction Options 3

Call tel. #2/monitoring rcvr. #2 for

2 Disabled  Enabled
special report codes
Section [804]

3 Call pager for special report codes  Disabled Enabled

Call personal tel. # on zone alarm
5 Disabled  Enabled
(burglary/fire)
6 Call personal tel. # on panic alarms Disabled  Enabled
Call personal tel. # on paramedic
7 Disabled  Enabled
alarms
Call personal tel. # on panel power
8  Disabled Enabled
trouble

GSM Options
Table 38: Description of GSM options (PCS series)

Option Description OFF ON Option Option

See options 1 See options 1 Primary Backup Description
1&2 GSM reporting 1 2 5 6
& 2, on right & 2, on right
3&4 Future use - - - - OFF OFF Landline Landline OFF OFF Disabled
Section [805]

GSM/GPRS no service trouble See options 5 See options 5

5&6 OFF ON Landline GSM OFF ON Trouble only
feedback & 6, on right & 6, on right
When disarmed: trouble
7 Future use - - - - ON OFF GSM Landline ON OFF only; when armed: audible
alarm
Silent alarm becomes
8 GSM RF jamming supervision Disabled  Enabled ON ON GSM GSM ON ON
audible alarm

= Default

IP/GPRS Options
Table 39: Description of IP/GPRS options (section [806])

Option Description OFF ON Option

Description
5&6 IP no service trouble feedback  See options 5 & 6 See options 5 & 6 5 6
As IP/GPRS
Section [806]

7 User dialer reporting  Enabled OFF OFF Disabled

reporting backup
8 Enable IP/GPRS reporting Disabled  Enabled OFF ON Trouble only

= Default ON OFF
When disarmed: trouble only; when
armed: audible alarm
ON ON Silent alarm becomes audible alarm

Communication Programming | 43
 Magellan & Spectra SP • Programming Guide

Report Codes and Partition Accounts

Use worksheet 36 to record your settings for sections [810] to [812].

Worksheet 36: Report Codes and Partition Accounts

Section Data Description
Tel. 1 & Tel. 2; Reporting format:
[810] ___/___ 0 = Ademco Slow; 1 = Silent Knight; 2 = Sescoa; 3 = Ademco Express; 4 = Ademco Contact ID;
5 = SIA (not supported with GPRS/IP reporting, as well as on SP65)
[811] ___/___/___/___ Partition 1 account number (landline/GSM communication only) Zero = A on a TM50
[812] ___/___/___/___ Partition 2 account number (landline/GSM communication only) Zero = A on a TM50

Landline and GSM Communication

Use worksheet 37 to record your settings for sections [815] to [819]. This worksheet applies to both landline and GSM communication.

Worksheet 37: Landline and GSM Communication Settings

Section Data Description
[815] __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__ Monitoring station telephone number 1
[817] __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__ Backup telephone number
[818] __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__ Pager telephone number
[819] __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__ Numeric message sent with pager reporting

Table 40: Special keys for telephone numbers

Function Keypad Key Function Keypad Key

* OFF Four-second pause TBL NOTE: To erase a phone number or numeric
# BYP Delete current digit SLEEP message, press sleep for each digit, in the
respective section.
Switch from pulse to tone dialing, or vice-versa MEM Insert a blank space

Timers
Use worksheet 38 to record your settings for sections [820] to [840]. For additional timers, see worksheets 40 and 49 on pages 45 and 51, respectively.

Worksheet 38: Communication Timers

Section Data Description Default
[820] ___/___/___ 000 to 255 hours Fail to comm. clear event timer 000 = disabled
[830] ___/___/___ 000 to 255 x 2 seconds TLM fail delay (landline only) 016
[831] ___/___/___ 000 to 032 Maximum dialing attempts monitoring station (landline and GSM only) 006
[832] ___/___/___ 000 to 127 seconds Delay between dialing attempts* (landline and GSM only) 020
[833] ___/___/___ 000 to 255 seconds Delay alarm transmission 000
[834] ___/___/___ 000 to 127 seconds Pager reporting delay 020
[835] ___/___/___ 000 to 010 Pager reporting message repetition 003
[836] ___/___/___ 000 to 127 seconds Personal reporting delay* 005
[837] ___/___/___ 000 to 010 Personal reporting message repetition* 003
[838] ___/___/___ 000 to 255 seconds Recent closing delay 000
[839] ___/___/___ 000 to 255 minutes Power failure report delay** 015
[840] ___/___/___ 000 to 255 days Auto test report (see table 36 on page 42) 007
* Also applicable when using a VDMP3 Plug-in Voice Dialer.
**For EN 50131, the maximum value for power failure delay is 60 minutes.

VDMP3 Options
Use worksheet 39 to record your setting for section [841]. For additional VDMP3 options, see worksheet 38.

Worksheet 39: VDMP3 Maximum Attempts

Section Data Description Default
[841] ___/___/___ 000 to 032 Maximum voice dialing attempts 006

44 | Communication Programming
Magellan & Spectra SP • Programming Guide

Test Report and Report Delays

Use worksheet 40 to record your settings for sections [850] to [852]. For additional timers, see worksheets 38 and 49 on pages 44 and 51, respectively.

Worksheet 40: Test Report and Report Delays

Section Data Description Default
[850] ___/__/__/___ HH:MM Auto test report time of day (see table 36 on page 42) 02:00
[851] ___/___/___ 000 to 255 minutes Armed report delay 005
[852] ___/___/___ 000 to 255 minutes Disarmed report delay 060

GSM Settings
Use worksheet 41 to record your settings for sections [855] to [856]. See table 41 on page 45 for applicable SMS language codes.

Worksheet 41: GSM Settings (PCS series)

Section Data Description Default
[855] ___/___/___ 000 to 255 x 2 seconds GSM no service timer 016
[856] ___/___/___ 000 to 255 SMS language (see table 41 for SMS language codes) 000
Table 41: SMS language codes for GSM settings

Input Value SMS Language Input Value SMS Language Input Value SMS Language Input Value SMS Language Input Value SMS Language
000 English 005 Polish 010 Czech 015 Russian 020 Serbian
001 French 006 Portuguese 011 Dutch 016 Bulgarian 021 to 255 Future use
002 Spanish 007 German 012 Croatian 017 Romanian
003 Italian 008 Turkish 013 Greek 018 Slovak
004 Swedish 009 Hungarian 014 Hebrew 019 Chinese

System and Communication Report Codes

Use the following section to program system report codes, as well as additional communication report codes on your MG/SP control panel.
Entering Report Codes
• For Ademco slow, Silent Knight, SESCOA, and Ademco express formats, key-in the desired two-digit hex value from 00 to FF.
• For Ademco Programmable Format, enter the desired two-digit hex value, found in table 43 on page 47. Entering FF will set the report code to those
outlined in table 44 on page 49.
• For Ademco All Codes Format, the control panel automatically generates report codes from the ones found in table 44 on page 49.

Special Arming and Disarming Report Codes

Use worksheet 42 to record your settings for special arming and disarming report codes.

Worksheet 42: Special Arming and Disarming Report Codes

Section Data Description Section Data Description Section Data Description
FF Auto-arming 00 Quick arming FF Cancel auto-arm
FF Late to close FF Arming via PC FF Disarming via PC
[860] [861] [862] Cancel alarm with user, or
FF No movement FF Arming with keyswitch FF
WinLoad/BabyWare
00 Partial arming FF - FF Cancel paramedic
Default: FF

Special Alarm Report Codes

Use worksheet 43 to record your settings for special alarm report codes.

Worksheet 43: Special Alarm Report Codes

Section Data Description Section Data Description
FF Emergency panic FF Zone shutdown
FF Auxiliary panic FF Duress
[863] [864]
04 Fire panic FF Keypad lockout
FF Recent closing FF Paramedic alarm

System and Communication Report Codes | 45

 Magellan & Spectra SP • Programming Guide

System Trouble Report Codes

Use worksheet 44 to record your settings for system trouble report codes.

Worksheet 44: Special Trouble Report Codes

Section Data Description Section Data Description Section Data Description
FF - FF Bell output overload FF Fail to communicate
FF AC failure FF Bell output disconnected FF RF jamming
[865] [866] [867]
FF Battery failure FF Timer loss FF Module lost
FF Auxiliary supply FF Fire loop trouble FF Module tamper
Wireless module
FF Module power fail FF Default: FF
supervision lost
[868] FF Module low/no battery* [869] FF Wireless module tamper
FF Wireless zone low battery FF Remote low battery
FF Wireless zone supervision lost FF -

System Trouble Restore Codes

Use worksheet 45 to record your settings for system trouble restore codes.

Worksheet 45: System Trouble Restore Codes

Section Data Description Section Data Description Section Data Description
FF TLM FF Bell output overload FF Fail to communicate
FF AC failure FF Bell output disconnect FF RF jamming
[870] [871] [872]
FF Battery failure FF Timer loss FF Module lost
FF Auxiliary supply FF Fire loop trouble FF Module tamper
Wireless module
FF Module power fail FF Default: FF
supervision lost*
[873] FF Module low/no battery* [874] FF Wireless module tamper
FF Wireless zone low battery FF Remote low battery
FF Wireless zone supervision lost FF -

System Special Report Codes

Use worksheet 46 to record your settings for system special report codes.

Worksheet 46: System Special Report Codes

Section Data Description Section Data Description Section Data Description
FF Cold start FF Installer in FF -
FF Test report FF Installer out FF -
[875] [876] [877]
FF - FF Closing delinquency FF -
FF Software out FF - FF Fail to arm
Default: FF

NOTE: For report code formatting instructions, see Entering Report Codes on page 45.

Installer Function Keys

Table 42: Description of installer functions for MG/SP keypads

Function Action Description

Test report ENTER + installer code + MEM Sends the Test Report report code programmed in section [875], to the monitoring station.
Cancels all communication with the WinLoad/BabyWare software or with the monitoring station, until
Cancel communication ENTER + installer code + STAY
the next reportable event.
Answer WinLoad/ Will force the console to answer an incoming call from the monitoring station, which is using the
ENTER + installer code + SLEEP
BabyWare software WinLoad/BabyWare software.
Call WinLoad/ Will dial the PC telephone number programmed in section [915], thereby initiating communication
ENTER + installer code + BYP
BabyWare software with a computer using the WinLoad software.
This mode allows to perform walk tests, where the siren will squawk to indicate opened zones.
Installer test mode ENTER + installer code + TBL
To exit, press TBL.

46 | System and Communication Report Codes

Magellan & Spectra SP • Programming Guide

Contact ID Report Codes Table 43: Ademco contact ID report codes (Continued) Table 43: Ademco contact ID report codes (Continued)
Table 43: Ademco contact ID report codes
Type CID # Reporting Code Value Type CID # Reporting Code Value
Type CID # Reporting Code Value 150 24-hour non-burglary 25 330 System peripheral 4F
100 Medical alarm 01 151 Gas detected 26 331 Polling loop open 50
Medical Alarms

101 Pendant transmitter 02 152 Refrigeration 27 332 Polling loop short 51

(100)

153 Loss of heat 28 333 Expansion module failure 52

102 Fail to report in 03

System Peripheral Troubles

24-hour Non-burglary
154 Water leakage 29 334 Repeater failure 53

(150 & 160)

110 Fire Alarm 04 155 Foil break 2A 335 Local printer paper out 54

(330 & 340)

111 Smoke 05 156 Day trouble 2B 336 Local printer failure 55

112 Combustion 06 157 Low bottled gas level 2C 337 Exp. module DC loss 56
158 High temperature 2D 338 Exp. module low battery 57
Fire Alarms

113 Water Flow 07

(110)

114 Heat 08 159 Low temperature 2E 339 Exp. module reset 58

115 Pull Station 09 161 Loss of air flow 2F 341 Exp. module tamper 59

116 Duct 0A 162 Carbon monoxide detected 30 342 Exp. module AC loss 5A

117 Flame 0B 163 Tank level 31 343 Exp. module self-test fail 5B

118 Near Alarm 0C 200 Fire supervisory 32 344 RF receiver jam detected 5C

120 Panic alarm 0D 201 Low water pressure 33 350 Communication 5D

Fire Supervisory
(200 & 210)

121 Duress 0E 202 Low CO2 34 351 Telco fault 1 5E

Communication Troubles
Panic Alarms

122 Silent 0F 203 Gate valve sensor 35 352 Telco fault 2 5F

(120)

(350 & 360)

123 Audible 10 204 Low water level 36 353 Long range radio 60

124 Duress - access granted 11 205 Pump activated 37 354 Fail to communicate 61

125 Duress - egress granted 12 206 Pump failure 38 355 Loss of radio supervision 62

130 Burglary 13 300 System trouble 39 356 Loss of central polling 63

131 Perimeter 14 301 AC loss 3A Long range radio VSWR

357 64
problem
132 Interior 15 302 Low system battery 3B
370 Protection loop 65
133 24-hour 16 303 RAM checksum bad 3C
Burglar Alarms

371 Protection loop open 66

Protection Loop Troubles

134 Entry/exit 17 304 ROM checksum 3D
(130)

372 Protection loop short 67

System Troubles

135 Day/night 18 305 System reset 3E

(300 & 310)

373 Fire trouble 68

136 Outdoor 19 306 Panel program changed 3F (370)
374 Exit error alarm 69
137 Tamper 1A 307 Self-test failure 40
375 Panic zone trouble 6A
138 Near alarm 1B 308 System shutdown 41
376 Hold-up zone trouble 6B
139 Intrusion verifier 1C 309 Battery test failure 42
377 Swinger trouble 6C
140 General alarm 1D 310 Ground fault 43
378 Cross-zone trouble 6D
141 Polling loop open 1E 311 Battery missing/dead 44
380 Sensor trouble 6E
312 Powr. supply over current limit 45
General Alarms

142 Polling loop short 1F

381 Loss of supervision - RF 6F
143 Extension module failure 20 313 Engineer reset 46
(140)

382 Loss of supervision - RPM 70

144 Sensor tamper 21 320 Sounder relay 47
383 Sensor tamper 71
321 Bell 1 48
Sounder/Relay Troubles

145 Expansion module tamper 22

384 RF transmitter low battery 72
146 Silent burglary 23 322 Bell 2 49
385 Smoke detector hi sensitivity 73
Sensor Troubles

147 Sensor supervision failure 24 323 Alarm relay 4A

(380 & 390)
(320)

386 Smoke detector low sensitivity 74

324 Trouble relay 4B
Intrusion detector hi
325 Reversing relay 4C 387 75
sensitivity
326 Notification appliance chk. #3 4D Intrusion detector low
388 76
327 Notification appliance chk. #4 4E sensitivity
389 Sensor self-test failure 77
391 Sensor watch trouble 78
392 Drift compensation error 79
393 Maintenance alert 7A

System and Communication Report Codes | 47

 Magellan & Spectra SP • Programming Guide

Table 43: Ademco contact ID report codes (Continued) Table 43: Ademco contact ID report codes (Continued) Table 43: Ademco contact ID report codes (Continued)

Type CID # Reporting Code Value Type CID # Reporting Code Value Type CID # Reporting Code Value
400 Open/close 7B 520 Sounder/relay disabled A9 601 Manual trigger test BD
401 Open/close by user 7C 521 Bell 1 disabled AA 602 Periodic test report BE

Sounder Relay Disabled

402 Group open/close 7D 522 Bell 2 disabled AB 603 Periodic RF transmission BF
Open/Close

403 Automatic open/close 7E 523 Alarm relay disabled AC 604 Fire test C0
(400)

(520)
406 Cancel 7F 524 Trouble relay disabled AD 605 Status report to follow C1
407 Remote arm/disarm 80 525 Reversing relay disabled AE 606 Listen-in to follow C2
408 Quick arm 81 Notification appliance chk. #3 607 Walk test mode C3
526 AF
disabled
409 Keyswitch open/close 82 Periodic test - system trouble
608 C4
Notification appliance chk. #4 present
411 Call back request made 83 527 B0
disabled
609 Video transmitter active C5
412 Successful - download access 84
Remote Access

Communication Disabled Modules

531 Module added B1

(530)
611 Point test OK C6
413 Unsuccessful access 85
(410)

532 Module removed B2 612 Point not tested C7

414 System shutdown 86
551 Dialer disabled B3 613 Intrusion zone walk tested C8
415 Dialer shutdown 87
614 Fire zone walk tested C9

Test/Misc
416 Successful upload 88
(550 & 560)

(600)
615 Panic zone walk tested CA
421 Access denied 89
552 Radio transmitter disabled B4 616 Service request CB
422 Access report by user 8A
621 Event log reset CC
423 Forced access 8B
622 Event log 50% full CD
424 Egress denied 8C
623 Event log 90% full CE
425 Egress granted 8D 570 Zone bypass B5
624 Event log overflow CF
426 Access door propped open 8E 571 Fire bypass B6
Access Control

625 Time/date reset D0

(420 & 430)

Access point door status 572 24-hour zone bypass B7

427 8F
monitor trouble 626 Time/date inaccurate D1
Bypasses

573 Burglary bypass B8

(570)

428 Access point request to exit 90 627 Program mode entry D2

574 Group bypass B9
429 Access program mode entry 91 628 Program mode exit D3
575 Swinger bypass BA
430 Access program mode exit 92 629 32-hour event log marker D4
576 Access zone shunt BB
431 Access threat level change 93 630 Schedule change D5
577 Access point bypass BC
432 Access relay/trigger fail 94 631 Exception schedule change D6
433 Access RTE shunt 95 632 Access schedule change D7
434 Access DSM shunt 96 654 System inactivity D8
441 Armed stay 97
442 Keyswitch armed stay 98
450 Exception open/close 99
451 Early open/close 9A
452 Late open/close 9B
(440 & 450)
Arming

453 Failed to open 9C

454 Failed to close 9D
455 Auto-arm failed 9E
456 Partial arm 9F
457 User exit error A0
458 User on premises A1
459 Recent close A2
461 Wrong code entry A3
462 Legal code entry A4
System

463 Re-arm after alarm A5

(460)

464 Auto-arm time extended A6

465 Panic alarm reset A7
466 Service ON/OFF premises A8

Version 4.7/4.92/5.12
Magellan & Spectra SP • Programming Guide

Automatic Report Codes

Table 44: List of automatic report codes

System Event Default Contact ID Report Code Default SIA Report Code
Arming with user code (##) 3 4A1 Close by user CL Closing report
Auto arming 3 4A3 Automatic close CA Automatic closing
Late to close 3 452 Late to close OT Late to close
No movement 3 452 Late to close NA No activity

Arm with PC software 3 4A7 Remote arm/disarm CQ Remote arming

Keyswitch arming 3 4A9 Keyswitch arming CS Keyswitch arming
Disarm with user code (##) 1 4A1 Open by user OP Opening report
Disarm after alarm with user code (##) 1 4A1 Open by user OP Opening report
Cancel alarm with user code (##) 1 4A6 Cancel by user OR Disarm from alarm
Auto arming cancellation 1 464 Deferred open/close CE Closing extend
Disarm with PC software 1 4A7 Remote arm/disarm OQ Remote disarming
Disarm after an alarm with PC software 1 4A7 Remote arm/disarm OR Disarm from alarm
Cancel alarm with PC software 1 4A6 Cancel by user OR Disarm from alarm
Cancel paramedic alarm 1 4A6 Cancel by user MH Medical alarm restore
Keyswitch disarm 1 4A9 Keyswitch disarm OS Keyswitch disarm
Keyswitch disarm after alarm 1 4A1 Keyswitch disarm after alarm OS Keyswitch disarm after alarm
Keyswitch cancel alarm 1 4A6 Keyswitch cancel alarm OS Keyswitch cancel alarm
Zone bypassed (##) 1 57A Zone bypass UB Untyped zone bypass
Zone alarm (##) 1 13A Burglary alarm BA Burglary alarm
Fire alarm (##) 1 11A Fire alarm FA Fire alarm
Zone alarm restore (##) 3 13A Burglary alarm restore BH Burglary alarm restore
Fire alarm restore (##) 3 11A Fire alarm restore FH Fire alarm restore
24-hr gas alarm (##) 1 151 Gas detected GA Gas alarm
24-hr heat alarm (##) 1 153 Loss of heat KA Heat alarm
24-hr water alarm (##) 1 154 Water leakage WA Water alarm
24-hr freeze alarm (##) 1 152 Refrigeration ZA Freeze alarm
24-hr gas alarm restore (##) 3 151 Gas restore GR Gas alarm restore
24-hr heat alarm restore (##) 3 153 Heat restore KR Heat alarm restore
24-hr water alarm restore (##) 3 154 Water restore WR Water alarm restore
24-hr freeze alarm restore (##) 3 152 Freeze restore ZR Freeze alarm restore
24-hr hold-up alarm 1 12A Panic alarm PA Panic alarm
24-hr hold-up alarm restore 3 12A Panic alarm restore PR Panic restore
Panic 1: emergency 1 12A Panic alarm PA Panic alarm
Panic 2: medical 1 1AA Medical alarm MA Medical alarm
Panic 3: fire 1 110 Fire Alarm FA Fire alarm
Recent closing 3 459 Open/close CR Recent closing
Global zone shutdown 1 575 Group bypass CG Close area
Duress alarm 1 121 Duress HA Hold-up alarm
Keypad lockout 1 421 Access denied JA User code tamper
Zone shutdown (##) 1 57A Zone bypass UB Untyped zone bypass
Zone tampered (##) 1 144 Sensor tamper TA Tamper alarm
Zone tamper restore (##) 3 144 Sensor tamper restore TR Tamper restoral
TLM Trouble 1 351 Telco 1 fault LT Phone line trouble
AC failure 1 3A1 AC loss AT AC trouble
Battery failure 1 3A9 Battery test failure YT System battery trouble
Auxiliary supply trouble 1 3AA System trouble YP Power supply trouble
Bell output current limit 1 321 Bell 1 YA Bell fault

System and Communication Report Codes | 49

 Magellan & Spectra SP • Programming Guide

Table 44: List of automatic report codes (Continued)

System Event Default Contact ID Report Code Default SIA Report Code
Bell absent 1 321 Bell 1 YA Bell fault
Clock lost 1 626 Time/date inaccurate JT Time changed
Fire loop trouble 1 373 Fire trouble FT Fire trouble
Communication fail 1 354 Communication fail YC Fail to communicate
RF jamming 1 344 RF receiver jam detection XQ RF jamming
GSM/GPRS module RF interference 1 552 Radio transmitter disabled YS Communication trouble
GSM/GPRS network failure 1 552 Radio transmitter disabled YS Communication trouble
GSM/GPRS supervision lost 1 552 Radio transmitter disabled YS Communication trouble
GSM/GPRS fail to communicate 1 354 Communication fails YC Fail to communicate
IP network failure 1 552 Radio transmitter disabled YS Communication trouble
IP supervision lost 1 552 Radio transmitter disabled YS Communication trouble
IP fail to communicate 1 354 Communication fails YC Fail to communicate
TLM trouble restore 3 351 Telco 1 fault restore LR Phone line restoral
AC failure restore 3 3A1 AC loss restore AR AC restoral
Battery failure restore 3 3A9 Battery test restore YR System battery restoral
Auxiliary supply trouble restore 3 3AA System trouble restore YQ Power supply restored
Bell output current limit restore 3 321 Bell 1 restore YH Bell restored
Bell absent restore 3 321 Bell 1 restore YH Bell restored
Clock programmed 3 625 Time/date reset JT Time changed
Fire loop trouble restore 3 373 Fire trouble restore FJ Fire trouble restore
Fail to communicate with monitoring station restore 3 354 Fail to communicate restore YK Communication fails restore
RF jamming restore 3 344 RF receiver jam detection restore XH RF jamming restoral
GSM/GPRS module RF interference restore 3 552 Radio transmitter restore YK Communication restore
GSM/GPRS network restore 3 552 Radio transmitter restore YK Communication restore
GSM/GPRS supervision restore 3 552 Radio transmitter restore YK Communication restore
GSM/GPRS fail to communicate restore 3 354 Communication restore YK Fail to communicate restore
IP network restore 3 552 Radio transmitter restore YK Communication restore
IP supervision restore 3 552 Radio transmitter restore YK Communication restore
IP fail to communicate restore 3 354 Communication restore YK Fail to communicate restore
Combus fault 1 333 Expansion module failure ET Expansion trouble
Module tamper 1 341 Expansion module tamper TA Tamper alarm
Module AC fail 1 342 AC failure on module AT Module AC fail
Module battery fail 1 338 Battery failure on module YT Module battery fail
Bus fault restore 3 333 Expansion module failure restore ER Expansion restoral
Module tamper restore 3 341 Expansion module tamper restore TR Tamper restoral
Module AC fail restore 3 342 AC restored on module AR Module AC fail restore
Module battery fail restore 3 338 Battery failure on module YR Module battery fail restore
Cold start 1 3A8 System shutdown RR Power up
Test report engaged 1 6A2 Periodic test report TX Test report
PC software communication finished 1 412 Successful - download access RS Remote program success
Installer on site 1 627 Program mode entry LB Local program
Installer programming finished 1 628 Program mode exit LS Local program success
Maintenance in 1 627 Program mode entry LB Local program
Maintenance out 1 628 Program mode exit LS Local program success
Closing delinquency 1 654 System inactivity CD System inactivity
Manual trigger test in 1 6A1 Manual trigger test in TS Manual trigger test in
Manual trigger test out 3 6A1 Manual trigger test out TS Manual trigger test out
Exit error 1 374 Exit error EE Exit error
RF module low battery 1 384 RF transmitter low battery XT Transmitter battery trouble
RF module battery restore 3 384 RF transmitter battery restore XR Transmitter battery restoral

50 | System and Communication Report Codes

Magellan & Spectra SP • Programming Guide

Table 44: List of automatic report codes (Continued)

System Event Default Contact ID Report Code Default SIA Report Code
RF zone supervision lost 1 381 Loss of supervision - RF US Untype zone supervision
RF zone supervision restore 3 381 Supervision restore - RF UR Untyped zone restoral
RF module supervision lost 1 381 Loss of supervision - RF US Untyped zone supervision
RF module supervision restore 3 381 Loss of supervision - RF restore UR Untyped zone restoral
RF module tamper 1 145 Expansion module tamper ES Expansion device tamper
RF module tamper restore 3 145 Expansion module tamper restore EJ Expansion device restore
Paramedic alarm 1 1AA Medical MA Medical alarm
Zone forced 1 57A Zone forced XW Zone forced
Zone included 3 57A Zone included UU Zone included
Remote low battery 1 338 Battery failure on module YT Module battery fail
Remote low battery restore 3 338 Battery failure on module restore YR Module battery fail restore
Failed to arm 1 454 Failed to close CI Failed to close

Communication Report Codes

Use worksheet 47 to record your settings for communication report codes. Sections [879] and [884] apply to both GSM and network (GPRS/GSM) communications.
See Communication Programming on page 42, for more communication features. In addition, refer to Description of Sections [966] and [967] on page 54, for clearing
and resetting codes.

Worksheet 47: Communication Report Codes

Section Data Description Section Data Description Section Data Description
GSM lost communication
FF PCS series RF jam FF - FF
with panel
FF PCS series no service FF IP100 no service FF -
[879] PCS series module [880] [884]
FF FF IP100 supervision lost FF -
supervision lost
Receiver fail to IP receiver fail to
FF FF FF -
communicate (GPRS) communicate

Communication Restore Report Codes

Use worksheet 48 to record your settings for communication restore report codes. Section [881] applies to both GSM and network (GPRS/GSM) communications.

Worksheet 48: Communication Restore Report Codes

Section Data Description Section Data Description
FF PCS series RF jam FF -
FF PCS series no service FF IP100 no service
[881] [882]
FF PCS series module supervision lost FF IP100 supervision lost
FF Receiver fail to communicate (GPRS) FF IP receiver fail to communicate

Software Options and Additional Timers

Use the following section to program software options and additional communication timers on your MG/SP control panel.
Table 45: Description of section [900] (WinLoad/BabyWare options)

Section Option Description OFF ON

1 Call back  Disabled Enabled
[900]
2 Automatic event buffer transmission  Disabled Enabled

= Default

Additional Communication Timers

Use worksheet 49 to record your settings for sections [901] and [902]. For additional timers, see worksheets 38 and 40. Sections [901] and [902] are also applicable
when using a VDMP3 Plug-in Voice Dialer.

Worksheet 49: Additional Communication Timers

Section Data Description Default
[901] ___/___/___ 000 to 255 rings Number of rings 008
[902] ___/___/___ 000 to 255 secs. (max 127) Answering machine override delay 030

Software Options and Additional Timers | 51

 Magellan & Spectra SP • Programming Guide

BabyWare Options
Use worksheet 50 to record your settings for WinLoad and BabyWare options.

Worksheet 50: BabyWare Options

Section Data Description
[910] ___/___/___/___ Panel ID
[911] ___/___/___/___ PC password
[915] __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__ PC telephone number (landline/GSM communication only)
WARNING: For increased communication security, change the default panel ID and PC password.

IP and Software Configurations

Use the following section to configure IP and software requirements on your MG/SP control panel.

IP Account Numbers
Use worksheet 51 to record the IP account numbers for network communication.

Worksheet 51: IP Account Numbers

Section Data Description
[918] ___/___/___/___ IP account partition 1
[919] ___/___/___/___ IP account partition 2

Software and PCS Connection Settings

Use worksheet 52 to record connection settings for WinLoad, BabyWare, and PCS series.

Worksheet 52: Software and PCS Connection Settings

Section Data Description Default
[920] __/__/__/__/__ Port 10000
[921] __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__ Access point name (APN), part 1 (e.g., internet.com) -
[922] __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__ Access point name (APN), part 2 -
[923] __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__ User name, part 1 -
[924] __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__ User name, part 2 -
[925] __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__ Password, part 1 -
[926] __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__ Password, part 2 -
[927] __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__ Installer software password (WinLoad, BabyWare) admin

IP Receiver Configurations
Use worksheets 53 to 55 (on page 53) to configure IP receivers. Table 46 provides a description of the IP/GPRS registration status.
Table 46: IP/GPRS registration status

Key Main Menu Trouble Key Sub-menu Trouble

1 OFF = Unregistered
1 IP/GPRS module registration status 1 Slow flash = Registering
1 ON = Registration OK
7 No IP/GPRS module
2 IP/GPRS module error 8 Ethernet cable unplugged; GSM no service
9 No IP address acquired by module/GPRS network trouble
7 No IP address (not programmed)
8 No IP port (not programmed)
3 IP/GPRS programming error
9 No IP account (not programmed)
10 No access point name (not programmed; GPRS only)
7 Cannot connect
8 Invalid profile
4 IP/GPRS registration error
9 Invalid format
10 Account already registered under another MAC address
Register module - When all troubles are cleared, press ARM to register module

52 | IP and Software Configurations

Magellan & Spectra SP • Programming Guide

Worksheet 53: IP Receiver 1 Configuration

Section Data Description Default
WAN1 IP address (e.g., 100.100.100.100); for one or
-
[929] __/__/__ . __/__/__ . __/__/__ . __/__/__ two-digit numbers, add 0s before the first digit
[930] __/__/__/__/__ WAN1 IP port 10000
[931] __/__/__ . __/__/__ . __/__/__ . __/__/__ WAN2 IP address -
[932] __/__/__/__/__ WAN2 IP port 10000
[933] __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__ IP password 123456
[934] __/__ IP profile (e.g., 01) -
[935] To view status or to register, press ARM (see table 46 on page 52) IP receiver status -

Worksheet 54: IP Receiver 2 Configuration

Section Data Description Default
[936] __/__/__ . __/__/__ . __/__/__ . __/__/__ WAN1 IP address (e.g., 100.100.100.100) -
[937] __/__/__/__/__ WAN1 IP port 10000
[938] __/__/__ . __/__/__ . __/__/__ . __/__/__ WAN2 IP address -
[939] __/__/__/__/__ WAN2 IP port 10000
[940] __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__ IP password 123456
[941] __/__ IP profile (e.g., 01) -
[942] To view status or to register, press ARM (see table 46 on page 52) IP receiver status -

Worksheet 55: IP Receiver Backup Configuration

Section Data Description Default
[943] __/__/__ . __/__/__ . __/__/__ . __/__/__ WAN1 IP address (e.g., 100.100.100.100) -
[944] __/__/__/__/__ WAN1 IP port 10000
[945] __/__/__ . __/__/__ . __/__/__ . __/__/__ WAN2 IP address -
[946] __/__/__/__/__ WAN2 IP port 10000
[947] __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__ IP password 123456
[948] __/__ IP profile (e.g., 01) -
[949] To view status or to register, press ARM (see table 46 on page 52) IP receiver status -

Usability Sections
The sections described in the ensuing segment are used to clear, reset, and display various settings and features on your MG/SP control panel.

Description of Sections [950], [955], and [960]

Table 47: Description of sections [950], [955], and [960]

Section Description
[950] Resets all programmable sections to their respective factory-set, default values. Once accessed, press ENTER to reset.
[955] Clears bus module troubles. Once cleared, remove disconnected module from the bus.
Displays the wireless transmitter serial number. Once accessed, press any button on the assigned remote control, or
[960]
press the tamper switch of the download memory key. Press ENTER to view the next digit.

Description of Section [965]

Table 48: Description of section [965] (reset labels)

Option Description OFF ON

1 Reset zone labels  Disabled Enabled
2 Reset user labels  Disabled Enabled
Section [965]

3 Reset partition labels  Disabled Enabled

4 Reset PGM labels  Disabled Enabled
5 Reset bus module labels  Disabled Enabled
6 Reset wireless repeater and siren labels  Disabled Enabled
7 Reset wireless keypad, repeater, and siren labels  Disabled Enabled

= Default

NOTE: When resetting any option in section [965], ensure that all other options are deselected. Press ENTER to reset the respective set of labels to their default
values, before exiting the section.

Usability Sections | 53
 Magellan & Spectra SP • Programming Guide

Description of Sections [966] and [967]

Table 49: Description of sections [966] and [967] (clear and reset report codes)

Option Description OFF ON Option Description OFF ON

1 Clear zone report codes Disabled  Enabled 1 Reset zone report codes to default Disabled  Enabled

2 Clear user report codes Disabled  Enabled 2 Reset user report codes to default Disabled  Enabled
Section [966]

Section [967]
Reset arm/disarm/alarm report codes
3 Clear arm/disarm/alarm report codes Disabled  Enabled 3 Disabled  Enabled
to default
4 Clear trouble report codes Disabled  Enabled 4 Reset trouble report codes to default Disabled  Enabled
Reset system special report codes to
5 Clear system special report codes Disabled  Enabled 5 Disabled  Enabled
default
Clear report code for GSM lost Reset report code for GSM lost
6 Disabled  Enabled 6 Disabled  Enabled
communication with panel communication with panel

= Default

NOTE: When clearing or resetting any option in sections [966] AND [967], ensure that all other options are deselected. Press ENTER to reset the respective set of
labels to their default values, before exiting the section.

Description of Sections [970], [975], and [980]

Table 50: Description of sections [970], [975], and [980]

Section Description
[970] Downloads data from the memory key to the control panel. To download data, enter section [970], and then press ENTER.
[975] Uploads data from the control panel to the memory key. To upload data, enter section [975], and then press ENTER.
[980] Displays version number of the control panel. Once accessed, press ENTER to view the next digit.

Label Programming with LCD Keypads

Use the information in the following section to program system labels, using an LCD keypad (K32LCD/K32LX).

Function keys
Table 51: Description of the special function keys, used for programming
labels on LCD keypads

Function Keypad Key

Insert space STAY

Delete SLEEP

Delete entire entry ARM

Toggle between numeric and alphanumeric keys OFF

Toggle between lower and upper case keys BYP

Insert special characters MEM

Move the cursor to the right 

Move the cursor to the left 

54 | Label Programming with LCD Keypads

Magellan & Spectra SP • Programming Guide

Catalogues of Special Characters

The following section outlines the different catalogues of special characters, including those in Hebrew, Greek, and Russian.
Figure 1: Standard special characters Figure 2: Hebrew special characters

032 048 064 080 096 112 160 176 192 208 224 240

033 049 065 081 097 113 161 177 193 209 225 241

034 050 066 082 098 114 162 178 194 210 226 242

035 051 067 083 099 115 163 179 195 211 227 243

036 052 068 084 100 116 164 180 196 212 228 244

037 053 069 085 101 117 165 181 197 213 229 245

038 054 070 086 102 118 166 182 198 214 230 246

039 055 071 087 103 119 167 183 199 215 231 247

040 056 072 088 104 120 168 184 200 216 232 248

041 057 073 089 105 121 169 185 201 217 233 249

042 058 074 090 106 122 170 186 202 218 234 250

043 059 075 091 107 123 171 187 203 219 235 251

044 060 076 092 108 124 172 188 204 220 236 252

045 061 077 093 109 125 173 189 205 221 237 253

046 062 078 094 110 126 174 190 206 222 238 254

047 063 079 095 111 127 175 191 207 223 239 255

Figure 4: Greek special characters

016 032 048 064 080 096 112 128 144 160 176 192 208 224 240

017 033 049 065 081 097 113 129 145 161 177 193 209 225 241

Figure 3: Russian special characters 018 034 050 066 082 098 114 130 146 162 178 194 210 226 242

019 035 051 067 083 099 115 131 147 163 179 195 211 227 243

020 036 052 068 084 100 116 132 148 164 180 196 212 228 244

021 037 053 A069 085 101 117 133 149 165 181 197 213 229 245

022 038 054 070 086 102 118 134 150 166 182 198 214 230 246

023 039 055 071 087 103 119 135 151 167 183 199 215 231 247

024 040 056 072 088 104 120 136 152 168 184 200 216 232 248

025 041 057 073 089 105 121 137 153 169 185 201 217 233 249

026 042 058 074 090 106 122 138 154 170 186 202 218 234 250

027 043 059 075 091 107 123 139 155 171 187 203 219 235 251

028 044 060 076 092 108 124 140 156 172 188 204 220 236 252

029 045 061 077 093 109 125 141 157 173 189 205 221 237 253

030 046 062 078 094 110 126 142 158 174 190 206 222 238 254

031 047 063 079 095 111 127 143 159 175 191 207 223 239 255

Figure 5: Polish, Hungarian, and Turkish special characters

001 002 003 004 005 006 007

Polish

001 002 003

Hungarian

001
Turkish

Label Programming with LCD Keypads | 55

 Magellan & Spectra SP • Programming Guide

Keypad Letter Assignments

The following section outlines the different configurations for keypad letter assignments, including those in Hebrew, Greek, and Russian.
Table 52: Standard keypad letter assignment Figure 6: Hebrew keypad letter assignment

Press Key Press Key Press Key

Key
Once Twice Three Times
1 A B C
2 D E F
3 G H I
4 J K L
5 M N O
6 P Q R
7 S T U
8 V W X
9 Y Z

Table 53: Greek keypad letter assignment

Figure 7: Russian keypad letter assignment
Press Key Press Key Press Key
Key
Once Twice Three Times
1 A B G
2 D E Z
3 H Q I
4 K L M
5 N O
6 P R S
7 T U F
8 C Y W

Trouble Display
The following section provides information on the different troubles associated with your MG/SP control panel. To view the trouble display, press TBL on your
MG/SP keypad. Table 54 outlines the troubles appearing in the main menu and their corresponding sub-menu troubles. To view the sub-menu troubles, press the
trouble’s respective key in the main menu.
NOTE: Keypads can be programmed to emit a beep every five seconds, whenever a new trouble condition has occurred. Press TBL to stop the beeping.
Table 54: Description of troubles for MG/SP control panels

Key Main Menu Trouble Key Sub-menu Trouble

1 Wireless zone low battery 1 to 32 Zones in low battery
1 Low/no battery on the control panel
2 AC failure on control panel
3 Auxiliary overload on control panel
4 Wireless keypad AC failure
2 Power trouble 5 Wireless keypad battery failure
6 Wireless repeater AC failure
7 Wireless repeater battery failure
8 Wireless siren AC failure
9 Wireless siren battery failure
10 Remote low battery (press [0] to view which remote)
1 Bell disconnected on control panel
3 Bell trouble
2 Bell overload on control panel

56 | Trouble Display
Magellan & Spectra SP • Programming Guide

Table 54: Description of troubles for MG/SP control panels

1 Telephone line monitoring on control panel

2 Fail to communicate on monitoring telephone 1, on control panel
3 Fail to communicate on monitoring telephone 2, on control panel
5 Fail to communicate on voice telephone, on control panel
6 Fail to communicate with PC, on control panel
4 Communication trouble 7 Fail to communicate with IP receiver 1 or 2 (GPRS)
8 Fail to communicate with IP receiver 1 or 2 (IP)
9 GSM no service (GSM network failure)
10 IP module no service (network failure)
STAY GSM RF jamming
OFF IP receiver unregistered (IP/GPRS)
5 Tamper and zone wiring failure 1 to 32 Zones in tamper and zone wiring failure
1 2WPGM
2 Keypad bus
6 Module tamper trouble 3 ZX8 bus module
4 RTX3 bus module
5 Wireless siren
6 GSM/GPRS module
7 Fire loop trouble 1 to 32 Zones in fire loop trouble
8 Timer loss -
1 to 32 Zones in supervision lost
9 Wireless zone supervision loss
STAY RF jamming trouble
1 2WPGM
2 Keypad bus (panel reset will not clear this trouble; clear it in section [955])
3 ZX8 bus module
4 RTX3 bus module
5 Wireless keypad
0 (10), or 10 Module supervision loss 6 Wireless repeater
7 -
8 VDMP3
9 PCS series
10 IP100
STAY Wireless siren
16 Keypad fault (K32, K32RF, K37, K35 only) -
17 Upgrade panel to V3.2 or higher (K37 only) -
SLEEP Keypad fault (K636, K10V/H only) -

Trouble Display | 57
 Magellan & Spectra SP • Programming Guide

Product Compatibility Chart

Table 55: Product compatibility chart for MG/SP control panels

MG5000 MG5050 SP4000 SP65 SP5500 SP6000 SP7000

Product Type Product
V4.1 - V4.5 V4.1 - V4.5 V4.9 V4.9 V4.5 V4.7 V5.0 V4.5 V4.7 V5.0 V4.5 V4.7 V5.0
K32LCD
(V1.30 or higher)       3   3   3

K32LX - -   -  - -  - -  -
Hardwired K32       3   3   3
Keypads
K10V/K10H       3   3   3
K35 (K32I)       3   3   3
K636       3   3   3

Wireless K37 (K32IRF)   - 2 2 2 2

Keypads K32RF (K32LRF)   - 2 2 2 2
ZX8        3    3   3

Zone Expansion ZX8SP       3   3   3

Modules RTX3 - -     3   3   3
RX1 - -     3   3   3
Wireless
SR150 (V1.10)   - 2   
Sirens
Wireless
Programmable 2WPGM   - 2 2 2 2
Output
REM1   1 1 1 1 1
REM15   1 1 1 1 1
Remote
REM2   2 2 2 2 2
Controls
REM3   2 2 2 2 2
RAC1    1
 1
 1
 1
1
Wireless
RPT1   - 2 2 2 2
Repeaters
PCS200 (V2.01 GSM/GPRS)       
PCS200
      
Reporting (V1.00 GSM edition)
and
IP100 (V1.50 IP reporting)       
Communication
IP100 (V1.00)       
VDMP3       
HUB2       3   3   3
Peripheral PGM4
      3   3   3
Modules (V3.00 and up)
PRT3 -    - - -
Programming
PMC5       
Keys
WinLoad   -   
Software
BabyWare - -   - - -

1 Requires RTX3/RX1

2
Requires RTX3
3
Requires modules V5.00 only
NOTE: For the most up-to-date and comprehensive MG/SP product compatibility chart, always refer to paradox.com.

58 | Product Compatibility Chart

Magellan & Spectra SP • Programming Guide

Hardware Connections
Single Zone Inputs

NOTE: Keyswitches are connected as standard zones and will follow ATZ options 1 and 2, programmed in section [705] (see page 37).

Advanced Technology Zone (ATZ) Connections

Hardware Connections | 59
 Magellan & Spectra SP • Programming Guide

Connecting Fire Circuits

For 4-wire installation, program the activation event so that the smoke detectors can be reset by simultaneously pressing CLEAR and ENTER for three seconds (see
event group 06 on page 21). For 2-wire installation, press CLEAR and ENTER simultaneously to automatically reset smoke detectors (not applicable to SP5500, SP4000,
SP65).

WARNING: It is recommended that smoke detectors be connected in a daisy-chain configuration. Each control panel, except for the SP4000, SP5500, and
SP65, supports a maximum of five 2-wire smoke detectors.

Alarm Relay and PGM Connections

Table 56: PGM power sources

Power Source Description

AUX + terminal • MG5000/MG5050: max. 700 mA
• SP5500/SP6000/SP7000: max. 700 mA
• SP4000: max. 600 mA
• SP65: max. 750 mA
External power supply PGMs cannot exceed 100 mA or the power supply’s
current limit.

AC Power & Backup Battery Connections

Table 57: Transformation requirements

Power Source Description

Transformer • 16 Vac 20 VA* (Amseco XP-1620)
• 16.5 Vac 40 VA (Universal UB1640W)
* not verified by UL
DC power supply rate • MG5000/MG5050: 1.0A
• SP5500/SP6000/SP7000: 1.4A
• SP4000/SP65: 1.1A
WARNING: A 12 Vdc / 7 Ah battery is required to comply with UL fire
Auxiliary supply rate • MG5000/MG5050: typ. 600 mA / max. 700 mA
requirements.
• SP5500/SP6000/SP7000: typ. 600 mA / max.
WARNING: Improper connection of the transformer may result in 700 mA
damage to the system. • SP4000: typ. 450 mA / max. 600 mA
WARNING: Disconnect battery before replacing the fuse. • SP65: typ. 500 mA / max. 750 mA
• UL installations: typ. 200 mA
Acceptable battery • MG5000/MG5050: 350 mA / 700 mA
charge current • SP5500/SP6000/SP7000: 350 mA / 700 mA
(see section [700], • SP4000/SP65: 1.1A
option 2, on page 36)

Demonstration or Emergency System Power-up without an AC Source

To power-up the control panel for demonstration or emergency purposes only, use a standard 12 VDC, 4 Ah/7 Ah backup battery. To power the control panel using
a backup battery:
1. Connect the battery to the control panel's BATT terminal.
2. Use a wire to short the battery's negative terminal to the panel's AUX- terminal.

60 | Hardware Connections
Magellan & Spectra SP • Programming Guide

PCB Layouts/Wiring Diagrams

MG5000

1 2 3 4 5 Do not cut, bend, or alter

the antennas, and ensure
that electrical wires do not

ANT
cross over them, as this
ANT may affect signal

DIALER
reception.

+AUX - GRN YEL

SERIAL

EBUS
To provide maximum
CHARGE lightning protection we
STATUS SERVICE strongly recommend having
5A/125V

RX
TX KEYPAD separate earth connections
RESET
for the dialer and zone
ground terminals.

MEMORY KEY
12 SERVICE
6
KEYPAD

Disconnect telephone line

RJ31X before servicing.
RED BLK
BATT AC PGM1PGM2
+
BELL
- +
AUX
-
GRN YEL Z1 C Z2 GND R-1 T-1 RING TIP CA 38A

11 10 9

GRN
BRN
GRY

RED
7
14
8 13
15
Teclado Magellan 16
18
Self-Contained Bell Connection
1K
RFL

ZONE RED BLK GRN YEL

+ + -
17
+
BELL

19
-

TRIGGER
+ -
+

-
AUX
-

SELF-CONTAINED
BELL/SIREN

1 Used for connecting the IP100 Internet Module; also used for In-Field 6 Paradox Memory Key (PMC-4, PMC5)
Firmware upgrade through a 307USB Direct Connect Interface 7 Refer to Hardware Connections on page 59
2 EBUS and Dialer used with: 8 The BELL output will shutdown if the current exceeds 3A
• VDMP3 Plug-in Voice Module for voice reporting 9 Refer to Alarm Relay and PGM Connections on page 60
• PCS Series GSM Communicator Module 10 16.5 Vac (50 or 60 Hz), minimum 20 VA (40 VA recommended)
3 LEDs 11 Refer to AC Power & Backup Battery Connections on page 60
Charge LED: 12 Refer to Panel Reset on page 3
• Charging and battery test 13 AWG #14 single conductor solid copper wire
Status LED: 14 Ground clamp
• Flash once every second: Normal 15 Cold water pipe grounding
• Flashes ON 1 sec. and OFF 1 sec.: Any trouble 16 To metallic enclosure
• Always ON: Panel is using phone line 17 For the keypad’s zone configurations, see Installer Quick Menu on page 7
• Fast flash 6 seconds after power-up: Installer lock enabled 18 If EOL is enabled, see section [706] option 2, on page 38; for the keypad’s
zone configurations, see Installer Quick Menu on page 7
RX & TX LED:
19 To connect additional wiring to auxiliary power, use the red (+) and black
• Flashes quickly when receiving or transmitting RF signals from
(-) keypad connectors; auxiliary power will shut down if current exceeds
wireless devices
1.1A; if the auxiliary output is overloaded and shuts down, you must
4 Four-pin connector can be used for quick installation of a keypad disconnect all loads from the output for at least 10 sec. before
5 Antennas reconnecting any load back to the auxiliary output

The sum of the current drawn from the BELL and AUX must be limited to 1.3A. Exceeding this limit will overload the panel power supply
and lead to complete system shutdown.
40 VA transformer strongly recommended.
This equipment must be installed and maintained by qualified service personnel only.
For UL and C-UL warnings, refer to the UL and C-UL Warnings section at the back of the MGSP Reference & Installation Manual.
Max. number of keypads: 15 keypads
Max. aux. current: 700 mA
Max. distance of bus module from panel: 76 m (250 ft.)
Max. total run of wire: 230 m (750 ft.)

PCB Layouts/Wiring Diagrams | 61

 Magellan & Spectra SP • Programming Guide

MG5050/MG5050E

1 2 3 4 5 Do not cut, bend, or alter

the antennas, and ensure
that electrical wires do not

ANT
ANT
cross over them, as this

MEMORY KEY
may affect signal
reception.

J4
6
20

J3

GRN YEL
To provide maximum
5A/125V

lightning protection we
CHARGE
strongly recommend having

SERIAL
+AUX -
SERVICE STATUS
KEYPAD
RX separate earth connections
TX
for the dialer and zone
SERVICE RESET
ground terminals.
KEYPAD
Disconnect
RJ31X telephone
RED BLK
BATT AC
+
BELL
-
PGM1 PGM2 PGM3 PGM4 + AUX - GRN YEL Z1 C Z2 Z3 C Z4 Z5 GND R-1 T-1 RING TIP CA 38A
line before
11 10 servicing.

GRN
BRN
GRY

RED
9 8 7
13 14
12
15
Magellan Keypad
16
18
Self-Contained Bell Connection
1K
EOL

ZONE RED BLK GRN YEL MG5050 EN 50131 Immunity to Attenuation Test
When performing the attenuation test, replace antenna A with the
following:
+ + -
17
+

• For a 433 MHz panel, use an antenna with a length of 10.2 cm (4

BELL

19 in.)
-

TRIGGER
+ - • For a 868 MHz panel, use an antenna with a length of 6.1 cm (2.4
+

- in.)
AUX

Once the test is complete, reinsert the original antenna (A) in its
-

SELF-CONTAINED place, and connect the wires (not shown) to a zone input
BELL/SIREN
programmed for tamper.

1 Paradox Memory Key (PMC-4, PMC5) 7 Refer to Panel Reset on page 3

2 J3 (EBUS) and J4 (DIALER) used with: 8 Refer to Hardware Connections on page 59
• VDMP3 Plug-in Voice Module for voice reporting 9 Refer to Alarm Relay and PGM Connections on page 60
• PCS Series GSM Communicator Module NOTE: +/- trigger on PGM4 only
3 Four-pin connector can be used for quick installation of a keypad 10 16.5 Vac (50 or 60 Hz), minimum 20 VA (40 VA recommended)
4 LEDs 11 Refer to AC Power & Backup Battery Connections on page 60
Charge LED: 12 The BELL output will shutdown if the current exceeds 3A
• Charging and battery test 13 AWG #14 single conductor solid copper wire
Status LED: 14 Ground clamp
• Flash once every second: Normal 15 Cold water pipe grounding
16 To metallic enclosure
• Flashes ON 1 sec. and OFF 1 sec.: Any trouble
17 For the keypad’s zone configurations, see Installer Quick Menu on page 7
• Always ON: Panel is using phone line
18 If EOL is enabled, see section [706] option 2, on page 38; for the keypad’s
• Fast flash 6 seconds after power-up: Installer lock enabled
zone configurations, see Installer Quick Menu on page 7
RX & TX LED:
19 To connect additional wiring to auxiliary power, use the red (+) and black
• Flashes quickly when receiving or transmitting RF signals from (-) keypad connectors; auxiliary power will shut down if current exceeds
wireless devices 1.1A; if the auxiliary output is overloaded and shuts down, you must
5 Antennas disconnect all loads from the output for at least 10 sec. before
6 Used for connecting the IP100 Internet Module; also used for In-Field reconnecting any load back to the auxiliary output
Firmware upgrade through a 307USB Direct Connect Interface 20 Tamper antenna (for EN 50131)

The sum of the current drawn from the BELL and AUX must be limited to 1.3A. Exceeding this limit will overload the panel power supply
and lead to complete system shutdown.
40 VA transformer strongly recommended.
This equipment must be installed and maintained by qualified service personnel only.
For UL and C-UL warnings, refer to the UL and C-UL Warnings section at the back of the MGSP Reference & Installation Manual.
Max. number of keypads: 15 keypads
Max. aux. current: 700 mA
Max. distance of bus module from panel: 76 m (250 ft.)
Max. total run of wire: 230 m (750 ft.)

62 | PCB Layouts/Wiring Diagrams

Magellan & Spectra SP • Programming Guide

SP4000

1 2

MEM KEY

EBUS
To provide maximum
5A/125V

SERIAL
lightning protection we

DIALER
strongly recommend
3 having separate earth
STATUS 4 connections for the dialer
and zone ground
terminals.

BATT
Disconnect telephone
RJ31X line before servicing.
RED BLK AC PG1
+
BELL
- +AUX - GRN YEL 1 C 2 3 C 4 GND R-1 T-1 RING TIP CA 38A

9 8 7

GRN
BRN
GRY

RED
5
11

6 12
10
13
Keypad 14
1K
EOL

ZONE RED BLK GRN YEL

+ -
15
16

1 EBUS port used for GSM reporting using the PCS Series GSM 8 16.5 Vac (50 or 60 Hz), minimum 20 VA (40 VA recommended)
Communicator Module; if using a CVT485 Plug-In RS485 Converter, 9 Refer to AC Power & Backup Battery Connections on page 60
connect the PCS module to the RS485 bus; 10 Connect to any common input
DIALER and EBUS port used for voice reporting with the VDMP3 Plug-in 11 AWG #14 single conductor solid copper wire
Voice Module. 12 Ground clamp
2 Paradox Memory Key (PMC-4, PMC5) 13 Cold water pipe grounding
3 Used for connecting the IP100 Internet Module; also used for In-Field 14 To metallic enclosure
Firmware upgrade through a 307USB Direct Connect Interface 15 For the keypad’s zone configurations, see Installer Quick Menu on page 7;
4 Status LED: If EOL is enabled, see section [706] option 2, on page 38
• Flash once every second: Normal 16 To connect additional wiring to auxiliary power, use the red (+) and black
• Flashes ON 1 sec. and OFF 1 sec.: Any trouble (-) keypad connectors; auxiliary power will shut down if current exceeds
• Always ON: Panel is using phone line 1.1A; if the auxiliary output is overloaded and shuts down, you must
• Fast flash 6 seconds after power-up: Installer lock enabled disconnect all loads from the output for at least 10 sec. before
5 Refer to Hardware Connections on page 59 reconnecting any load back to the auxiliary output
6 The BELL output will shutdown if the current exceeds 3A
7 Refer to Alarm Relay and PGM Connections on page 60 Panel Reset
To perform a panel reset, see Panel Reset on page 3.

The sum of the current drawn from the BELL and AUX must be limited to 1.3A. Exceeding this limit will overload the panel power supply
and lead to complete system shutdown.
40 VA transformer strongly recommended.
This equipment must be installed and maintained by qualified service personnel only.
For UL and C-UL warnings, refer to the UL and C-UL Warnings section at the back of the MGSP Reference & Installation Manual.
Max. number of keypads: 15 keypads
Max. aux. current: 450 mA
Max. distance of bus module from panel: 76 m (250 ft.)
Max. total run of wire: 230 m (750 ft.)

PCB Layouts/Wiring Diagrams | 63

 Magellan & Spectra SP • Programming Guide

SP5500

1 2 3 4 5

MEMORY KEY SERIAL

STATUS

DIALER EBUS
6
5A/125V

+AUX - GRN YEL

To provide maximum
CHARGE RESET
lightning protection we
strongly recommend having
+
RED BLK

_ separate earth connections

BATT

13
SERVICE for the dialer and zone
12 SERVICE
KEYPAD
KEYPAD ground terminals.

11
Disconnect telephone
RJ31X line before servicing.
+ - +AUX - GRN
AC PGM1 PGM2 BELL YEL Z1 C Z2 Z3 C Z4 Z5 C GND R-1 T-1 RING TIP CA 38A

10 9

GRN
BRN
GRY

RED
7
14
15
8
16
Magellan Keypad 17
Self-Contained Bell Connection 19
1K
EOL

ZONE RED BLK GRN YEL

+ + -
18
+
BELL

20
-

TRIGGER
+ -
+

-
AUX
-

SELF-CONTAINED
BELL/SIREN

The sum of the current drawn from the BELL and AUX must be limited to 1.3A. Exceeding this limit will overload the panel power supply
and lead to complete system shutdown.
40 VA transformer strongly recommended.
This equipment must be installed and maintained by qualified service personnel only.
For UL and C-UL warnings, refer to the UL and C-UL Warnings section at the back of the MGSP Reference & Installation Manual.
Max. number of keypads: 15 keypads
Max. aux. current: 700 mA
Max. distance of bus module from panel: 76 m (250 ft.)
Max. total run of wire: 230 m (750 ft.)

64 | PCB Layouts/Wiring Diagrams

Magellan & Spectra SP • Programming Guide

SP6000

1 2 3 4 5

MEMORY KEY SERIAL

STATUS

DIALER EBUS
6

+AUX - GRN YEL

5A/125V

CHARGE RESET To provide maximum

lightning protection we
TRIGGER
RED BLK

- +

14
BATT

strongly recommend having

SERVICE separate earth connections
for the dialer and zone
13 SERVICE KEYPAD
KEYPAD ground terminals.
12
Disconnect telephone
RJ31X
+ - + - Z1 C Z2 Z3 C Z4 Z5 C Z6 Z7 C Z8 CA 38A line before servicing.
AC PGM1 PGM2 PGM3 PGM4 RELAY BELL AUX GRN YEL GND R-1 T-1 RING TIP

11

GRN
BRN
GRY

RED
10 9 7

8 16
15
17
Magellan Keypad 18
20
1K

Self-Contained Bell Connection

EOL

ZONE RED BLK GRN YEL

+ -
+
19
+
BELL

21
-

TRIGGER
+ -
+

-
AUX
-

SELF-CONTAINED
BELL/SIREN

1 Charge LED: 11 16.5 Vac (50 or 60 Hz), minimum 20 VA (40 VA recommended)

• Charging and battery test 12 Refer to Panel Reset on page 3
2 Status LED: 13 PGM trigger: this jumper allows you to choose whether the solid state
• Flash once every second: Normal relay PGMs are grounded (-) or give out 12V (+)
• Flashes ON 1 sec. and OFF 1 sec.: Any trouble 14 Refer to AC Power & Backup Battery Connections on page 60
• Always ON: Panel is using phone line 15 AWG #14 single conductor solid copper wire
• Fast flash 6 seconds after power-up: Installer lock enabled 16 Ground clamp
3 Four-pin connector can be used for quick installation of a keypad 17 Cold water pipe grounding
4 EBUS and Dialer used with: 18 To metallic enclosure
• VDMP3 Plug-in Voice Module for voice reporting 19 For the keypad’s zone configurations, see Installer Quick Menu on page 7
• PCS Series GSM Communicator Module 20 If EOL is enabled, see section [706] option 2, on page 38; for the keypad’s
zone configurations, see Installer Quick Menu on page 7
5 Used for connecting the IP100 Internet Module; also used for In-Field
21 To connect additional wiring to auxiliary power, use the red (+) and black
Firmware upgrade through a 307USB Direct Connect Interface
(-) keypad connectors; auxiliary power will shut down if current exceeds
6 Paradox Memory Key (PMC-4, PMC5)
1.1A; if the auxiliary output is overloaded and shuts down, you must
7 Refer to Hardware Connections on page 59
disconnect all loads from the output for at least 10 sec. before
8 The BELL output will shutdown if the current exceeds 3A
reconnecting any load back to the auxiliary output
9 Programmable output relay: max. 5A @ 60 Vdc or 120 Vac
10 Refer to Alarm Relay and PGM Connections on page 60

The sum of the current drawn from the BELL and AUX must be limited to 1.3A. Exceeding this limit will overload the panel power supply
and lead to complete system shutdown.
40 VA transformer strongly recommended.
This equipment must be installed and maintained by qualified service personnel only.
For UL and C-UL warnings, refer to the UL and C-UL Warnings section at the back of the MGSP Reference & Installation Manual.
Max. number of keypads: 15 keypads
Max. aux. current: 700 mA
Max. distance of bus module from panel: 76 m (250 ft.)
Max. total run of wire: 230 m (750 ft.)
When using an SP6000 in conjunction with an RTX3, all K32 and K10V/H keypads must be versions 2.0 and higher.

PCB Layouts/Wiring Diagrams | 65

 Magellan & Spectra SP • Programming Guide

SP65

1 2 3

MEM KEY
EBUS
STATUS

5A/125V

SERIAL
4

RED
BATT BLK
10

+ - +AUX - 1 C 2 3 4 C 5 6 7 C 8 P/T
AC PG1 PG2 PG3 BELL GRN YEL

9 5
8
6 11
13
7 12
Keypad

1K
EOL
14

ZONE RED BLK GRN YEL

15

17
+ -
16

1 Status LED: 9 16.5 Vac (50 or 60 Hz), minimum 20 VA (40 VA recommended)

• Flash once every second: Normal 10 Refer to AC Power & Backup Battery Connections on page 60
• Flashes ON 1 sec. and OFF 1 sec.: Any trouble 11 Connect to any common input
• Always ON: Panel is using phone line 12 AWG #14 single conductor solid copper wire
Fast flash 6 seconds after power-up: Installer lock enabled 13 Ground clamp
2 EBUS port used for GSM reporting using the PCS Series GSM 14 Cold water pipe grounding
Communicator Module; if using a CVT485 Plug-In RS485 Converter, 15 To metallic enclosure
connect the PCS module to the RS485 bus; 16 To connect additional wiring to auxiliary power, use the red (+) and black
DIALER and EBUS port used for voice reporting with the VDMP3 Plug-in (-) keypad connectors; auxiliary power will shut down if current exceeds
Voice Module. 1.1A; if the auxiliary output is overloaded and shuts down, you must
3 Paradox Memory Key (PMC-4, PMC5) disconnect all loads from the output for at least 10 sec. before
4 Used for connecting the IP100 Internet Module; also used for In-Field reconnecting any load back to the auxiliary output
Firmware upgrade through a 307USB Direct Connect Interface 17 For the keypad’s zone configurations, see Installer Quick Menu on page 7;
5 Panic/tamper input If EOL is enabled, see section [706] option 2, on page 38
6 Refer to Hardware Connections on page 59
7 The BELL output will shutdown if the current exceeds 3A Panel Reset
8 Refer to Alarm Relay and PGM Connections on page 60 To perform a panel reset, see Panel Reset on page 3.

The sum of the current drawn from the BELL and AUX must be limited to 1.3A. Exceeding this limit will overload the panel power supply
and lead to complete system shutdown.
40 VA transformer strongly recommended.
This equipment must be installed and maintained by qualified service personnel only.
For UL and C-UL warnings, refer to the UL and C-UL Warnings section at the back of the MGSP Reference & Installation Manual.
Max. number of keypads: 15 keypads
Max. aux. current: 500 mA
Max. distance of bus module from panel: 76 m (250 ft.)
Max. total run of wire: 230 m (750 ft.)

66 | PCB Layouts/Wiring Diagrams

Magellan & Spectra SP • Programming Guide

SP7000

1 2 3 4 5 6

SERIAL
RESET

DIALER
STATUS

MEMORY KEY
5A/125V

EBUS
CHARGE
7

+AUX - GRN YEL

RED BLK
BATT

To provide maximum
TRIGGER
14 lightning protection we
SERVICE
SERVICE strongly recommend having
- + KEYPAD
KEYPAD separate earth connections
for the dialer and zone
13 ground terminals.

Disconnect telephone
RJ31X
+ - CA 38A
line before servicing.
AC PGM1 PGM2 PGM3 PGM4 RELAY BELL +AUX - GRN YEL GND R-1 T-1 RING TIP

GRN
BRN
GRY

RED
12 10 8
11
16
9 15
17
20 Magellan Keypad 18
Self-Contained Bell Connection
1K
EOL

ZONE RED BLK GRN YEL

+ -
+
19
+
BELL

21
-

TRIGGER
+ -
+

-
AUX
-

SELF-CONTAINED
BELL/SIREN

1 Charge LED: 11 Refer to Alarm Relay and PGM Connections on page 60

• Charging and battery test 12 16.5 Vac (50 or 60 Hz), minimum 20 VA (40 VA recommended)
2 Status LED: 13 PGM trigger: this jumper allows you to choose whether the solid state
• Flash once every second: Normal relay PGMs are grounded (-) or give out 12V (+)
• Flashes ON 1 sec. and OFF 1 sec.: Any trouble 14 Refer to AC Power & Backup Battery Connections on page 60
• Always ON: Panel is using phone line 15 AWG #14 single conductor solid copper wire
• Fast flash 6 seconds after power-up: Installer lock enabled 16 Ground clamp
3 Refer to Panel Reset on page 3 17 Cold water pipe grounding
4 EBUS and Dialer used with: 18 To metallic enclosure
• VDMP3 Plug-in Voice Module for voice reporting 19 For the keypad’s zone configurations, see Installer Quick Menu on page 7
• PCS Series GSM Communicator Module 20 If EOL is enabled, see section [706] option 2, on page 38; for the keypad’s
zone configurations, see Installer Quick Menu on page 7
5 Four-pin connector can be used for quick installation of a keypad
21 To connect additional wiring to auxiliary power, use the red (+) and black
6 Used for connecting the IP100 Internet Module; also used for In-Field
(-) keypad connectors; auxiliary power will shut down if current exceeds
Firmware upgrade through a 307USB Direct Connect Interface
1.1A; if the auxiliary output is overloaded and shuts down, you must
7 Paradox Memory Key (PMC-4, PMC5)
disconnect all loads from the output for at least 10 sec. before
8 Refer to Hardware Connections on page 59
reconnecting any load back to the auxiliary output
9 The BELL output will shutdown if the current exceeds 3A
10 Programmable output relay: max. 5A @ 60 Vdc or 120 Vac

The sum of the current drawn from the BELL and AUX must be limited to 1.3A. Exceeding this limit will overload the panel power supply
and lead to complete system shutdown.
40 VA transformer strongly recommended.
This equipment must be installed and maintained by qualified service personnel only.
For UL and C-UL warnings, refer to the UL and C-UL Warnings section at the back of the MGSP Reference & Installation Manual.
Max. number of keypads: 15 keypads
Max. aux. current: 700 mA
Max. distance of bus module from panel: 76 m (250 ft.)
Max. total run of wire: 230 m (750 ft.)

PCB Layouts/Wiring Diagrams | 67

Touch Screen TM50
Touch and hold - -
Default panel ONCE only!

Led Keypads
- Magellan & Spectra
Default panel ONCE only! Quick Programming Guide
AU Defaults V1.7
Reset Switch
Press and hold until status light flashes fast, release, then press again once quickly.

Zones 001 ~ 032 (32 Zones) Dialler Timers

Location Zone Type Area Zone Options Location Features Data Location Features Data
001 1 01 1 12345678 Note Account Number (811) 0 = A on TM50 710 Entry Delay 1 030
002 2 06 1 12345678 811 Account P1 ____ 712 Swinger Shutdown 001

003 3 09 1 12345678 815 Phone # 1 _________ _ 713 Twin Trip Timer 048

004 4 09 1 12345678 817 Backup Phone _________ _ 720 Sleep Entry Delay 015

005 5 09 1 12345678 840 Auto Test Days 007 745 Area 1 Exit Time 045

006 6 09 1 12345678 850 Auto Test Time 02 : 00 747 Bell Timer 004

007 7 09 1 12345678 839 AC Fail Delay 015

008 8 09 1 12345678

00 - Disabled 1 - Swinger Shutdown

01 - Entry 1 + Sleep 2 - BypassableZone Installer / Master Codes PGM's (Panel specific)
03 - Entry 1 3 - RF Zone Supervision
06 - Handover + Sleep 4 - Siren:Stdy, Sil, Pulsed Location Codes Data PGM 1 Strobe
07 - Handover 5 - Siren:Stdy, Sil, Pulsed
09 - Instant + Sleep 6 - Twin Trip 397 Installer 0000 PGM 2 Screamer
10 - Instant 7 - Delay Alarm TX
12 - Fire (30 sec delay) 8 - Forced Zone enable 399 System Master 1234 PGM 3 Smoke Reset
15 - 24 Hour Buzzer
16 - 24 Hour Audible PGM 4 Button C on Remote
PGM 5 Button C on Remote

700 701 702 703 704

1 Partitioning 1 4 digit code 1 Panic 1, Police 1 Quick arm away 1 Force arm away
2 Battery charge increase 2 Lock master code 2 Panic 2, Medical 2 Quick arm stay 2 Force arm stay
3 C/Pad beeps on trouble 3 Confidential mode 3 Panic 3, Fire 3 Quick arm sleep 3 Force arm sleep
4 C/Pad beeps on AC fail 4 Key to exit confidential 4 Panic 1, audible 4 Quick bypass 4 Bell squawk / remotes
5 RF jam supervision 5 Confidential time 5sec 5 Panic 2, audible 5 No Arm if battery fail 5 Bell squawk / keypad
6 Exit delay termination 6 REM2 V2.01 up 6 Panic 3, audible 6 No Arm if tamper 6 Exit Beeps enabled
7 Tmp sup. on bus/module 7 Entry delay on LCD 7 N/A 7 No Arm if supervision 7 No exit beeps / stay arm
8 N/A 8 Exit delay on LCD 8 N/A 8 Arm/Disarm VDMP3 8 No exit delay / remotes

705 706 800 801 802

1 Zone Doubling 1 Supervision check in 1 Phone line monitor 1 Open ONLY after alarm 1 Open/Close Rec # 1
2 Parallel EOLs 2 EOLs enabled 2 Phone line monitor 2 Zone restores 2 Open/Close Rec # 2
3 Zone tamper 3 2 Wire smoke 3 Pulse dialling 3 Auto test 3 Open/Close Pager
4 Zone tamper 4 ZX8 A Zone 1 = tamper 4 Alternate dial 4 Auto test 4 N/A
5 Tamper on bypass 5 ZX8 B Zone 1 = tamper 5 Force dial 5 Contact ID override 5 Alarm/Restores Rec # 1
6 Wireless supervision 6 ZX8 C Zone 1 = tamper 6 DTMF 6 Bell on alarm kissoff 6 Alarm/Restores Rec # 2
7 Wireless supervision 7 N/A 7 Pulse ratio 7 Bell on arming kissoff 7 Alarm/Restores Pager
8 Supervision on bypass 8 N/A 8 Deactivate dialler 8 C/Pad beeps on kissoff 8 N/A

Note: Turn 1 OFF

for Monitored Commercial
User Report Codes 471 ~ 502 (32 users)
Notes
FF FF for Commercial installations
Location Codes Data EOL's 1K (Green), 2K2 (Red Red Red)
471 User 1 00 FF 181~212 Zone Labels
472 User 2 00 FF 341~356 PGM Labels
473 User 3 00 FF 511~542 User Labels
474 User 4 00 FF 955 Module Scan
475 User 5 00 FF 970 Download from Key TO control panel
476 User 6 00 FF 975 Upload FROM control panel to Key
477 User 7 00 FF 0 Sleep B OFF

478 User 8 00 FF C BYP F

Wireless
Wireless Zones 061 ~ 092 (32 Zones) Wireless Keyfobs 651 ~ 682 (32 Keyfobs) Wireless Keypads 571 ~ 578 (8 Keypads)
Signal Strength = 101 ~ 132 Labels = 511 ~ 542 Signal Strength = 591 ~ 598
Labels = 181 ~ 212 Labels = 599 ~ 606
PWR + BYP to learn in

Location Zone Serial Number Location Keyfobs Serial Number Location Keypad Serial Number

061 1 000000 651 1 000000 571 1 000000

062 2 000000 652 2 000000 572 2 000000

063 3 000000 653 3 000000 573 3 000000

064 4 000000 654 4 000000 574 4 000000

065 5 000000 655 5 000000 575 5 000000

066 6 000000 656 6 000000 576 6 000000

067 7 000000 657 7 000000 577 7 000000
068 8 000000 658 8 000000 578 8 000000

Wireless PGM's 301 ~ 316 (16 PGM's) Wireless Siren 683 ~ 686 (4 max) Wireless Repeater
Signal Strength = 321 ~ 336 Signal Strength = 687 ~ 690 Signal Strength = 548 ~ 549
Labels = 341 ~ 356 Labels = 691 ~ 694 Labels = 568 ~ 569
RPT1 Device allocation = 551 ~ 557
RPT2 Device allocation = 561 ~ 567

Location PGM Serial Number Location Siren Serial Number Location Repeater Serial Number

301 1 000000 683 1 000000 545 1 000000

302 2 000000 684 2 000000 546 2 000000

303 3 000000 685 3 000000

304 4 000000 686 4 000000

305 5 000000
Key fob Buttons functions ( REM1, 2 and 15)
306 6 000000
Location +
307 7 000000
610 (1 4) (C 8)
308 8 000000 (Arm) (Sleep) (PGM) (Panic) REM 15 REM 2 REM 3

Backlight Trouble Display

Step 1 Wireless zone low battery
1 Hold for 3 seconds 2 Power trouble
2 Press to raise / lower 3 Bell trouble

3 to Exit 4 Communication trouble

5 Tamper / Zone wiring trouble
Personal Phone Numbers 6 Module tamper trouble
Step 7 Fire loop trouble
1 [MASTER CODE] 8 Timer loss
2 9 Wireless zone supervision loss
3 Personal Phone # 1 10 Module supervision loss
Personal Phone # 2 16 Keypad fault (K32, K35, K37)
Personal Phone # 3 Sleep Keypad fault (K10, K636)
Personal Phone # 4 Additional information on page 56 of
programming manual
Personal Phone # 5
4 Phone Number
5 to Exit

Smoke Reset
Step
1

1 Press and hold for 5

seconds

Chime On / Off
Step
Press and hold Zone key to turn
1
Chime On / Off 1300 319 499
 Magellan & Spectra SP • Programming Guide

The whole Paradox team wishes you a successful and easy installation. We hope this product performs to your complete satisfaction.
Should you have any questions or comments, please contact us.
For support, please contact your local distributor, or dial 1-800-791-1919 (in North America) or
+1-450-491-7444 (outside North America), Monday to Friday, from 8:00 a.m. to 8:00 p.m. EST.
You may also e-mail us at [email protected].
Additional information can be found at PARADOX.COM

68 | PCB Layouts/Wiring Diagrams

 1300 319 499

MGSP-EP29_AU_V1.31