Solution Ultima 862

Quick Reference Guide

ISSUE 1.70
2 Solution Ultima 862 Quick Reference Guide

Solution Ultima 862

Quick Reference Guide
Copyright  2002 by Bosch Security Systems Pty Limited,
SYDNEY, AUSTRALIA

Document Part Number MA486Q

DOCUMENT ISSUE 1.70
Printed 23 May 2006

This documentation is provided to suit the Solution Ultima 862 control panels.
Firmware Revision 1.00 – 1.09
Hardware Revision A - J
Alarm Link required = 2.74 or higher
Control Panel Software Version 1.00 – 1.09 = S486_V10

Copyright Notice
All rights reserved. No part of this publication may be reproduced, transmitted or stored in a retrieval system in
any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior
written permission of Bosch Security Systems Pty Limited.

Trademarks
Throughout this document trademark names may have been used. Rather than put a trademark symbol in every
occurrence of a trademark name, we state that we are using the names only in an editorial fashion and to the
benefit of the trademark owner with no intention of infringement of the trademark.

Notice of Liability
While every precaution has been taken in the preparation of this document, neither Bosch Security Systems Pty
Limited nor any of its official representatives shall have any liability to any person or entity with respect to any
liability, loss or damage caused or alleged to be caused directly or indirectly by the information contained in this
book.

Bosch Security Systems Pty Limited reserves the right to make changes to features and specifications at any
time without prior notification in the interest of ongoing product development and improvement.

SOL ULTIMA 862 QUICK REF GUIDE.DOCBosch Security Systems Pty Limited
Solution Ultima 862 Quick Reference Guide 3

Introduction
Thank you for choosing the Solution control panel for your installation. We are sure that you will
find this system extremely flexible, reliable and easy to use. The quick reference guide is supplied
with the system to provide users with enough basic information to wire, configure and program the
system. Due to the systems many programmable features and options, we suggest that you obtain
the complete installation manual that provides detailed information on system options and functions
and programming methods.

Programming
The programming options of the system are stored in a non-volatile EPROM. This memory will
hold all information during a total power loss and can be changed as many times as required.

In general, the entire programming sequence will consist of entering a location number and then
change the data as required.

Programming the system can be via the following methods:

• Codepad
• Hand Held Programmer
• Alarm Link Software

Programming Using A Codepad

The system needs to be disarmed (with no active alarm) to program the system. If there is an
active alarm or the system is armed, enter the code for User 1 (Default = 2580) followed by the #
key (User Code 1 is factory default as the Master Code).

To enter installer’s programming mode, enter the installer code (Default = 1234) followed by the #
key. Two beeps will be heard and both the STAY and AWAY indicators will flash simultaneously to
indicate that you have entered programming mode. The codepad indicators will display the current
data programmed in LOCATION 000 (First location of the Primary Telephone Number).

To move to another programming location, enter the location number followed by the # key. The
data in the new location will now be displayed via the codepad indicators (eg. If you entered 34#,
the system will jump you to LOCATION 034, the beginning of the Subscriber ID Number For
Receiver 1).

To move to the next location, press the # key. This will step you to the next location. The data in
the next location will now be displayed via the codepad indicators (eg. If you are currently
positioned at LOCATION 034, pressing the # key will take you to LOCATION 035).

To step back one location, press the * key (eg. If you are currently positioned at LOCATION 35,
pressing the * key will take you back to LOCATION 34).

To change data in the current location, enter the new value (0 – 15) followed by the * key. This will
store the new data into the location and leave you at the same location (eg. If you enter the value
14*, both the Zone 4 indicator and the MAINS indicator will display to represent the new data
value).

To move to the next location, press the # key. The data in the next location will now be displayed.

To exit Installer’s Programming Mode, enter 960#. Two beeps will be heard and the STAY and
AWAY indicators will no longer display. The system has now returned to the disarmed state and is
now ready for use.

The table below is a quick guide to programming:

Enter Installer’s Programming Mode 1234#

Exit Installer’s Programming Mode 960#
Step To Next Location #
Step Back One Location *
Program New Data Into Location Data + * (Data = 0 – 15)
Jump To Another Location Location No. + #

Electronics Design and Manufacturing Pty LimitedSOL ULTIMA 862 QUICK REF GUIDE.D
4 Solution Ultima 862 Quick Reference Guide

Codepad Indicators

Data Zone 1 Zone 2 Zone 3 Zone 4 Zone 5 Zone 6 Zone 7 Zone 8 MAINS
Value Indicator Indicator Indicator Indicator Indicator Indicator Indicator Indicator Indicator
0
1 X
2 X
3 X
4 X
5 X
6 X
7 X
8 X
9 X X
10 X
11 X X
12 X X
13 X X
14 X X
15 X X

Programming Option Bits

You will notice option bits throughout the quick reference guide. This allows you to program any
combination of the four different options in the one location by adding the options together.
Programming a zero (0) will disable all four options.

Example
If at LOCATION 177 you only want options 1, 2 and 4, add the numbers together and the total is
the number to be programmed. In this example, the number to be programmed is 7 (eg. 1 + 2 + 4
= 7).

Option Description
1 Dialler Reporting Functions Allowed
2 Remote Arming Via Telephone Allowed
4 Answering Machine Bypass Only When Armed
8 Use Bell 103 For FSK Format (Disabled = CCITT V21)

Installer’s Programming Commands

These commands can only be used when you enter Installer’s Programming Mode. Enter the
command followed by the # key.

Command Description
958 Enable/Disable Zone Status (Hand Held Programmer Required)
959 Test Programming Key
960 Exit Installer’s Programming Mode
961 Default System Back To Factory Settings
962 Copy Panel Memory To Programming Key
963 Copy Programming Key To Panel Memory
964 Erase Programming Key
965 Default System For Domestic Dialling Format
966 Enable/Disable Automatic Stepping Of Locations When Programming
999 Display Software Version (Hand Held Programmer Required)

SOL ULTIMA 862 QUICK REF GUIDE.DOCBosch Security Systems Pty Limited
Solution Ultima 862 Quick Reference Guide 5

Arming The System (On) Isolating Zones

Standard Isolating
AWAY Mode
1. Press the * key twice.
1. Press and hold the # key until two beeps are
heard. 2. Enter the zone number that you want to
isolate followed by the * key.
Or

2. Enter your code followed by the # key. Repeat step 2 if more than one zone is
[eg. 2580 + #]. required to be isolated.

3. Press the # key to exit when finished.

STAY Mode 1
1. Press and hold the * key until two beeps are Code To Isolate
heard. 1. Press the * key once.
Or 2. Enter your user code, followed by the * key .
2. Enter your code followed by the * key.
3. Enter the zone number that you want to
[eg. 2580 + *].
isolate followed by the * key.

Repeat step 2 if more than one zone is

STAY Mode 2 required to be isolated.
1. Press and hold the 0 key until two beeps are
heard. 4. Press the # key to exit when finished.

Disarming The System (Off) Add/Delete RF Devices (Wireless Zones)

AWAY Mode Add RF Device

1. Enter your code followed by the # key. 1. Enter the Installer Code followed by 0 and the
[eg. 2580 + #]. # key [eg. 1234 + 0 + #].

2. Enter the Device Number (1 – 16) that you

STAY Mode 1 want to add followed by the # key.
1. Press and hold the * key until two beeps are
heard (Only if no alarm). 3. Enter the 9-digit RF device ID number
followed by the # key.
Or

2. Enter your code followed by the # key.

Delete RF Device
[eg. 2580 + #].
1. Enter the Installer Code followed by 0 and the
# key [eg. 1234 + 0 + #].
STAY Mode 2
2. Enter the Device Number (1 – 16) that you
1. Press and hold the 0 key until two beeps are want to delete followed by the # key.
heard (Only if no alarm).
3. Press the * key to delete the RF device.
Or

2. Enter your code followed by the # key.

[eg. 2580 + #].

Electronics Design and Manufacturing Pty LimitedSOL ULTIMA 862 QUICK REF GUIDE.D
6 Solution Ultima 862 Quick Reference Guide

Set First Test Report Add RF Keyfob

1. Enter the Installer Code followed by 1 and the 1. Enter the Master Code followed by 1 and the
key [eg. 1234 + 1 + #]. # key [eg. 2580 + 1 + #].

2. Enter the Number Of Days (0 – 15) to wait 2. Enter the User Number (9 – 16) that you want
until first test report followed by the # key. to add followed by the # key.

3. Enter the 9-digit RF keyfob ID number

followed by the # key.
Event Memory Recall
1. Enter the Installer Code or Master Code
followed by 8 and the # key.
[eg. 1234 + 8 + #]. Delete A User Code / RF Keyfob
1. Enter the Master Code followed by 1 and the
The last 40 events (non partitioned) or last 10 events # key [eg. 2580 + 1 + #].
(partitioned) will be displayed in reverse order (i.e. 2. Enter the User Number (1 – 16) that you want
most recent to least recent). to delete followed by the # key.

3. Press the * key to delete the user code.

Walk Test Mode
1. Enter the Installer Code or Master Code
followed by 7 and the # key. Change Domestic Telephone Numbers
[eg. 1234 + 7 + #]. 1. Enter the Installer Code or Master Code
followed by 2 and the # key.
2. Test each zone as required. [eg. 1234 + 2 + #].
3. Press the # key to exit. 2. Enter the digits for the telephone number.

3. If more than one telephone number, press the

Satellite Siren Service Mode * key followed by the 4 key (inserts break
1. Enter the Installer Code followed by 5 and the between phone numbers) and repeat Step 2,
# key [eg. 1234 + 5 + #]. else press the # key to exit.

Telephone Monitor Mode (Toggle On/Off) Turn Outputs On/Off

1. Enter the Installer Code followed by 6 and the 1. Enter the Master Code followed by 5 and the
# key [eg. 1234 + 6 + #]. # key [eg. 2580 + 5 + #].

2. Press and hold the 9 key until two beeps are 2. Enter the Output Number (1 – 3) that you
heard to send a test report. want to toggle on or off.

Zone LED Dialling Event 3. Press the # key to toggle On or the * key to
1 Telephone Line Seized toggle Off.
2 Dialling Telephone Number
3 Handshake Received 4. Press the # key to exit.
4 Data Being Sent
5 Kiss-Off Received
None Released Telephone Line Setting Date and Time
1. Enter the Master Code followed by 6 and the
# key [eg. 2580 + 6 + #].
Add A User Code
1. Enter the Master Code followed by 1 and the 2. Enter the day (DD), month (MM) and year
# key [eg. 2580 + 1 + #]. (YY) followed by the hour (HH) and minute
(MM).
2. Enter the User Number (1 – 8) that you want
to add / change followed by the # key. 3. Press the # key to exit.

3. Enter the New Code followed by the # key.

Day Alarm – Toggle On/Off
1. Press and hold the 4 key until two beeps are
heard. Day alarm will toggle on or off.

SOL ULTIMA 862 QUICK REF GUIDE.DOCBosch Security Systems Pty Limited
Solution Ultima 862 Quick Reference Guide 7

STAY Mode 2 Zones - Program Codepad Buzzer Tone

1. Enter the Installer Code or Master Code 1. Press and hold the 8 key until the desired
followed by 4 and the # key. buzzer tone has been reached.
[eg. 1234 + 4 + #].
2. Press the # key to exit.
2. Enter the Zone Number that you want the
system to automatically isolate followed by the
* key. Test Report
1. Press and hold the 9 key until two beeps are
Repeat if more than one zone to be heard.
automatically isolated when armed in STAY
Mode 2.

3. Press the # key to exit. Speaker Test

1. Press and hold the 1 key until two beeps are
heard. The speaker will sound for two
Fault Analysis seconds.
1. Press and hold the 5 key until two beeps are
heard.
Bell Test
2. Zone Indicators will display FAULT condition 1. Press and hold the 2 key until two beeps are
(see table below). heard. The piezo will sound for two seconds.
3. Press # key to exit.

Zone
Strobe Test (Toggle On/Off)
FAULT Condition 1. Press and hold the 3 key until three beeps are
LED
Press and Hold Button 1 heard to turn the strobe on.
To Determine Fault
1 = Battery Fail 2. Press and hold the 3 key until two beeps are
2 = Date/Time heard to turn the strobe off.
3 = RF Rx Jamming
RF Rx Tamper
1 System Fault
RF Rx Comm’s Fail
4 = Horn Speaker Fail Telco Arm Sequence (Call Forward On)
5 = Telephone Line Fail 1. Enter your Installer Code or Master Code
6 = E2 Fail followed by 3 and the # key.
7 = Fuse Fail [eg. 1234 + 3 + #].
8 = AC Fail
Press and Hold Button 2 2. Press 1 followed by the # key.
To Determine Fault
2 RF Low Battery
Displays Zones (1 – 8) that 3. Enter the Call Forward On sequence.
registers RF Low Battery
Press and Hold Button 3 4. Press the # key to exit.
To Determine Fault
3 Zone Tamper
Displays Zones (1 – 8) that
registers Zone Tamper
Press and Hold Button 4 Telco Disarm Sequence (Call Forward On)
To Determine Fault 1. Enter your Installer Code or Master Code
4 Sensor Watch
Displays Zones (1 – 8) that followed by 3 and the # key.
registers Zone Tamper
[eg. 1234 + 3 + #].
Press and Hold Button 5
To Determine Fault
5 RF Sensor Watch
Displays Zones (1 – 8) that
2. Press 2 followed by the # key.
registers Zone Tamper
Press and Hold Button 6 3. Enter the Call Forward Off sequence.
To Determine Fault
6 Communication Fail 4. Press the # key to exit.
1 = Receiver 1 Fail (Dialler)
2 = Receiver 2 Fail (Dialler)

Modem Call (Alarm Link)

1. Press and hold the 6 key until two beeps are
heard.

Latching Outputs (Reset)

1. Press and hold the 7 key until two beeps are
heard.

Electronics Design and Manufacturing Pty LimitedSOL ULTIMA 862 QUICK REF GUIDE.D
8 Solution Ultima 862 Quick Reference Guide

Location 000 – 015

Phone Number 1 - Receiver 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
(0=10 and telephone termination = 0, anywhere else 0=0)
Location 016 – 031
Phone Number 2 – Receiver 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
(0=10 and telephone termination = 0, anywhere else 0=0)
Location 032
Handshake Tone 1 = HI-LO Handshake (Contact ID) 4 = No Handshake
For Receiver 1 2 = 1400 Hz (Ademco TX @ 1900 Hz) 5 = Pager
1
3 = 2300 Hz (Sescoa TX @ 1800 Hz)
Location 033
Transmission Format 1 = Contact ID 4 = Domestic 7 = Reserved
For Receiver 1 2 = 4 + 2 Expressed 5 = Basic Pager 8 = 4+2 Pulsed
3 = FSK 300 Baud 6 = Reserved
1
Location 034 - 039
Subscriber ID Number For Receiver 1 0 0 0 0 0 0
(right justified)
Location 040 – 055
Phone Number 1 - Receiver 2 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
(0=10 and telephone termination = 0, anywhere else 0=0)
Location 056 – 071
Phone Number 2 - Receiver 2 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
(0=10 and telephone termination = 0, anywhere else 0=0)
Location 072
Handshake Tone 1 = HI-LO Handshake (Contact ID) 4 = No Handshake
For Receiver 2 2 = 1400 Hz (Ademco TX @ 1900 Hz) 5 = Pager
1
3 = 2300 Hz (Sescoa TX @ 1800 Hz)
Location 073
Transmission Format 1 = Contact ID 4 = Domestic 7 = Reserved
For Receiver 2 2 = 4 + 2 Expressed 5 = Basic Pager 8 = 4+2 Pulsed
3 = FSK 300 Baud 6 = Reserved
1
Location 074 - 079
Subscriber ID Number For Receiver 2 0 0 0 0 0 0
(right justified)
Location 80
Dialling Format 1 = Australian DTMF 4 = International DTMF
2 = Australian Decadic 5 = Reversed Decadic
3 = Alternate DTMF & Decadic (Aust) 6 = Alternate DTMF & Reversed Decadic
1
Location 081 – 112
Reserved

Location 113 – 142

Telco Arming Sequence (Call Forward On)
0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0

Location 143 – 158

Telco Disarm Sequence (Call Forward Off) 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
Location 159 – 174
Call Back Telephone Number 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
(0=10 and telephone termination = 0, anywhere else 0=0)
Location 175
Ring Count 0 = Panel Will Not Answer 14 = Answering Machine Bypass 2
8
1 – 13 = No Of Rings Until Panel Answers 15 = Answering Machine Bypass 1
Location 176
Telephone Line Fail Options 1 = Display FAULT Indicator When Telephone Line Fails
2 = Sound Alarm When System Is Armed
4 = Sound Alarm When System Is Disarmed
Note: Option 2 & 4 Must Be Used In Conjunction With Option 1
(Eg. Program a 1, 3, 5 or 7) 0

SOL ULTIMA 862 QUICK REF GUIDE.DOCBosch Security Systems Pty Limited
Solution Ultima 862 Quick Reference Guide 9

Location 177
Dialler Options 1 1 = Dialler Reporting Functions Allowed
2 = Remote Arming Via Telephone Allowed
4 = Answering Machine Bypass Only When Armed 9
8 = Use Bell 103 For FSK Format (Disabled = CCITT V21)
Location 178
Dialler Options 2 1 = Open/Close Reports Only If Previous Alarm
2 = Open/Close Reports For STAY Mode 1 and STAY Mode 2
4 = Delay Siren Until Transmission Complete
8 = Extend Handshake Wait Time From 30 To 55 Seconds
0
Location 179
Dialler Options 3 1 = Set DTMF Dialling Pulses To 1 Digit/Second
2 = Lockout Telephone Line Fail Alarm (V1.03+)
4 = Change Decadic Dialling To 60/40
8 = Reserved
0
Location 179
Dialler Options 3 (V1.04+) 1 = Set DTMF Dialling Pulses To 1 Digit/Second
2 = Lockout Telephone Line Fail Alarm (V1.03+)
4 = Change Decadic Dialling To 60/40 2
8 = External Modem Module (CC811) Required For FSK (V1.09+)
Location 180
Alarm Link Options 1 = Upload/Download Allowed
2 = Call Back Phone Number Required For Upload/Download
4 = Exit Upload/Download Connection On Alarm
8 = External Modem Module (CC811) Required For Alarm Link 3
Location 181 - 184
Installer Code
1 2 3 4
Location 185 - 264
User Codes
Location 185 - 188 189 Location 190 - 193 194 Location 195 - 198 199
User #01 User #02 User #03
2 5 8 0 10 15 15 15 15 2 15 15 15 15 2
Authority Authority Authority
Level Level Level

Location 200 - 203 204 Location 205 - 208 209 Location 210 - 213 214
User #04 User #05 User #06
15 15 15 15 2 15 15 15 15 2 15 15 15 15 2
Authority Authority Authority
Level Level Level

Location 215 - 218 219 Location 220 - 223 224 Location 225 - 228 229
User #07 User #08 RF User #09
15 15 15 15 2 0 15 15 15 3 15 15 15 15 2
Authority Authority Authority
Level Level Level

Location 230 - 233 234 Location 235 - 238 239 Location 240 - 243 244
RF User #10 RF User #11 RF User #12
15 15 15 15 2 15 15 15 15 2 15 15 15 15 2
Authority Authority Authority
Level Level Level

Location 245 - 248 249 Location 250 - 253 254 Location 255 - 258 259
RF User #13 RF User #14 RF User #15
15 15 15 15 2 15 15 15 15 2 15 15 15 15 2
Authority Authority Authority
Level Level Level

Location 260 - 263 264

RF User #16
15 15 15 15 2
Authority
Level

Authority
Description
Level
0 Arm/Disarm
1 Arm Only
2 Arm/Disarm + Open/Close Reports
3 Arm Only + Close Reports
4 Arm/Disarm + Code Required To Isolate
6 Arm/Disarm + Open/Close Reports + Code Required To Isolate
8 Master Code + Arm/Disarm
10 Master Code + Arm/Disarm + Open/Close Reports
12 Master Code + Arm/Disarm + Code Required To Isolate
14 Master Code + Arm/Disarm + Code Required To Isolate + Open/Close Reports

Electronics Design and Manufacturing Pty LimitedSOL ULTIMA 862 QUICK REF GUIDE.D
10 Solution Ultima 862 Quick Reference Guide

Location 265
Day Alarm Zones 1 = Zone 1 4 = Zone 3
2 = Zone 2 8 = Zone 4 0
Location 266
EOL Resistor Value
0 = No EOL 6 = 4K7 12 = Reserved
1 = 1K 7 = 5K6 13 = Reserved
2 = 1K5 8 = 6K8 14 = Split EOL (3K3/6K8 With Tamper (1K)
3 = 2K2 9 = 10K 15 = Split EOL (3K3/6K8)
4 = 3K3 10 = 12K
5 = 3K9 11 = 22K
15

Location 267 - 322

Zone Defaults

Location 267 268 269 270 271 272 273

Zone #01
2 0 0 1 14 1 1
(Default = Delay-1) Zone Zone Pulse Zone Pulse Zone Zone Report Dialler
Type Count Count Time Options 1 Options 2 Code Options

Location 274 275 276 277 278 279 280

Zone #02
1 0 0 1 14 1 1
(Default = Handover) Zone Zone Pulse Zone Pulse Zone Zone Report Dialler
Type Count Count Time Options 1 Options 2 Code Options

Location 281 282 283 284 285 286 287

Zone #03
1 0 0 1 14 1 1
(Default = Handover) Zone Zone Pulse Zone Pulse Zone Zone Report Dialler
Type Count Count Time Options 1 Options 2 Code Options

Location 288 289 290 291 292 293 294

Zone #04
1 0 0 1 14 1 1
(Default = Handover) Zone Zone Pulse Zone Pulse Zone Zone Report Dialler
Type Count Count Time Options 1 Options 2 Code Options

Location 295 296 297 298 299 300 301

Zone #05
0 0 0 1 14 1 1
(Default = Instant) Zone Zone Pulse Zone Pulse Zone Zone Report Dialler
Type Count Count Time Options 1 Options 2 Code Options

Location 302 303 304 305 306 307 308

Zone #06
0 0 0 1 14 1 1
(Default = Instant) Zone Zone Pulse Zone Pulse Zone Zone Report Dialler
Type Count Count Time Options 1 Options 2 Code Options

Location 309 310 311 312 313 314 315

Zone #07
13 0 0 1 12 1 1
(Default = 24 Hr Fire) Zone Zone Pulse Zone Pulse Zone Zone Report Dialler
Type Count Count Time Options 1 Options 2 Code Options

Location 316 317 318 319 320 321 322

Zone #08
9 0 0 1 12 1 1
(Default = 24 Hr Tamper) Zone Zone Pulse Zone Pulse Zone Zone Report Dialler
Type Count Count Time Options 1 Options 2 Code Options

SOL ULTIMA 862 QUICK REF GUIDE.DOCBosch Security Systems Pty Limited
Solution Ultima 862 Quick Reference Guide 11

Zone Types

Zone Type Description Zone Type Description

0 Instant 8 24 Hr Hold-Up
1 Handover 9 24 Hr Tamper
2 Delay-1 10 Reserved
3 Delay-2 11 Keyswitch
4 Reserved 12 24 Hr Burglary
5 Reserved 13 24 Hr Fire
6 24 Hr Medical 14 Chime
7 24 Hr Panic 15 Not Used

Zone Pulse Count

The pulse count allows you to program how many pulses (0 – 15) need to be registered within the pulse count
time to activate an alarm.

Zone Pulse Count Time

Option 20ms Loop Response Time Option 150 ms Loop Response Time
0 0.5 Seconds 8 20 Seconds
1 1 Second 9 30 Seconds
2 2 Seconds 10 40 Seconds
3 3 Seconds 11 50 Seconds
4 4 Seconds 12 60 Seconds
5 5 Seconds 13 90 Seconds
6 10 Seconds 14 120 Seconds
7 15 Seconds 15 200 Seconds

Zone Options 1 Zone Options 2

Option Description Option Group
1 Lockout Siren/Dialler 1 Isolated In STAY Mode 1
2 Delay Alarm Report 2 Zone Isolation Allowed
4 Silent Alarm 4 Forced Arming Allowed
8 Sensor Watch 8 Zone Restore Report Allowed

Zone Dialler Options

Option Group
0 No Zone Reports Allowed
1 Report To Receiver 1
2 Report To Receiver 2
4 Report To Both Receiver 1 & Receiver 2
8 Report To Receiver 2 Only If Receiver 1 Fails

Keyswitch Zone Options

The keyswitch zone options replace Zone Options 1 only for the zones that have been programmed to operate
as a keyswitch zone.

Option Description
0 Latching Arm and Disarm In AWAY Mode
1 Latching Arm In AWAY Mode
2 Latching Disarm From AWAY Mode Or STAY Mode
4 Latching Arm and Disarm In STAY Mode
5 Latching Arm In STAY Mode
6 Latching Disarm From STAY Mode
8 Momentary Arm and Disarm In AWAY Mode
9 Momentary Arm In AWAY Mode
10 Momentary Disarm From AWAY Mode Or STAY Mode
12 Momentary Arm and Disarm In STAY Mode
13 Momentary Arm In STAY Mode
14 Momentary Disarm From STAY Mode

Electronics Design and Manufacturing Pty LimitedSOL ULTIMA 862 QUICK REF GUIDE.D
12 Solution Ultima 862 Quick Reference Guide

Location 323
Swinger Shutdown Count For Siren 0 = Unlimited / 1 - 15 = Number Of Times Siren Operate Till Lockout 3
Location 324
Swinger Shutdown Count For Dialler 0 = Unlimited / 1 - 15 = Number Of Times Dialler Operate Till Lockout 6

Location 325 - 326

Zone Status – Zone Tamper Report Location 325 = Zone Tamper Report
Location 326 = Zone Tamper Restore Report 0 0

Location 327 - 328

Zone Status – Walk Test Report Location 327 = Walk Test Start Report
Location 328 = Walk Test End Report 0 0
Location 329 - 330
Zone Status - Bypass Report Location 329 = Zone Bypass Report
9 8
Location 330 = Zone Bypass Restore Report
Location 331 - 332
Zone Status - Trouble Report Location 331 = Zone Trouble Report
Location 332 = Zone Trouble Restore Report 2 3
Location 333 - 334
Zone Status - Sensor Watch Report Location 333 = Sensor Watch Report
Location 334 = Sensor Watch Restore Report 4 5
Location 335
Zone Status - Alarm Restore Code 14
Location 336
Zone Status Reporting Options 0 = No Zone Status Reports Allowed
1 = Report To Receiver 1
2 = Report To Receiver 2
4 = Report To Both Receiver 1 & Receiver 2
8 = Report To Receiver 2 Only If Receiver 1 Fails 1
Location 337
RF Supervision Time 0
Location 337 = Increments Of 6 Hours (0 - 90 Hours)

Location 338 - 339

RF Low Battery Report Location 338 = RF Low Battery Report
Location 339 = RF Low Battery Restore Report 6 8
Location 340 - 341
RF Receiver Trouble Report Location 340 = RF Receiver Trouble Report (Tens Digit)
Location 341 = RF Receiver Trouble Report (Units Digit) 7 9
Location 342 - 343
RF Receiver Trouble Restore Report Location 342 = RF Receiver Trouble Restore Report (Tens Digit)
Location 343 = RF Receiver Trouble Restore Report (Units Digit) 7 11
Location 344
RF Dialler Options 0 = No Zone Status Reports Allowed
1 = Report To Receiver 1
2 = Report To Receiver 2
4 = Report To Both Receiver 1 & Receiver 2
8 = Report To Receiver 2 Only If Receiver 1 Fails 1

Location 345 - 346

Open/Close Reports Location 345 = Open Report
Location 346 = Close Report 11 12
Location 347
Open/Close Reporting Options 0 = No Open/Close Reports Allowed
1 = Report To Receiver 1
2 = Report To Receiver 2
4 = Report To Both Receiver 1 & Receiver 2
8 = Report To Receiver 2 Only If Receiver 1 Fails 1

SOL ULTIMA 862 QUICK REF GUIDE.DOCBosch Security Systems Pty Limited
Solution Ultima 862 Quick Reference Guide 13

Location 348
Codepad Duress Report 6
Location 349 - 350
Codepad Panic Report Location 349 = Tens Digit
Location 350 = Units Digit 7 15
Location 351 - 352
Codepad Fire Report Location 351 = Tens Digit
Location 352 = Units Digit 7 14
Location 353 - 354
Codepad Medical Report Location 353 = Tens Digit
Location 354 = Units Digit 7 13
Location 355
Codepad Reporting Options 0 = No Codepad Alarm Reports Allowed
1 = Report To Receiver 1
2 = Report To Receiver 2
4 = Report To Both Receiver 1 & Receiver 2
8 = Report To Receiver 2 Only If Receiver 1 Fails 1
Location 356 - 357
System Status - Fuse Fail Report Location 356 = Tens Digit
Location 357 = Units Digit 10 3
Location 358 - 359
System Status - Fuse Fail Restore Report Location 358 = Tens Digit
Location 359 = Units Digit 10 8
Location 360 - 361
System Status - AC Fail Report Location 360 = Tens Digit
10 2
Location 361 = Units Digit
Location 362 - 363
System Status - AC Fail Restore Report Location 362 = Tens Digit
10 7
Location 363 = Units Digit
Location 364 - 365
System Status - Low Battery Report Location 364 = Tens Digit
10 1
Location 365 = Units Digit
Location 366 - 367
System Status - Low Battery Location 366 = Tens Digit
10 6
Restore Report Location 367 = Units Digit
Location 368 - 370
Location 368 = Code Retry Limit (0 = Unlimited) 368 369 370
System Status - Access Denied (Code Retry)
Location 369 = Tens Digit 6 7 12
Location 370 = Units Digit
Location 371
System Status Reporting Options 0 = No Codepad Alarm Reports Allowed
1 = Report To Receiver 1
2 = Report To Receiver 2
4 = Report To Both Receiver 1 & Receiver 2
8 = Report To Receiver 2 Only If Receiver 1 Fails 1
Location 372 - 378
Test Report Time (Automatic) Location 372 = Hour Of Day (Tens Digit)
Location 373 = Hour Of Day (Units Digit)
Location 374 = Minute Of Day (Tens Digit) 372 373 374 375 376 377 378
Location 375 = Minute Of Day (Units Digit)
Location 376 = Test Report (Tens Digit) 0 0 0 0 7 1 0
Location 377 = Test Report (Units Digit) H H M M Tens/Units Interval
Location 378 = Repeat Interval In Days Report Code

Location 379
Test Reporting Dialler Options 0 = No Codepad Alarm Reports Allowed
1 = Report To Receiver 1
2 = Report To Receiver 2
4 = Report To Both Receiver 1 & Receiver 2
1
8 = Report To Receiver 2 Only If Receiver 1 Fails

Electronics Design and Manufacturing Pty LimitedSOL ULTIMA 862 QUICK REF GUIDE.D
14 Solution Ultima 862 Quick Reference Guide

Location 368 - 397

Outputs
Location 380 381 382 383 384 385 Location 386 387 388 389 390 391
Output 1 Output 2
1 14 0 0 0 0 2 7 10 2 1 5
Default = Horn Event Polarity Time Time Base Default = Fire Alarm Event Polarity Time Time Base
Speaker Code Base Multiplier With Verification Code Base Multiplier

Location 392 393 394 395 396 397 Location 398 399 400 401 402 403
Strobe Output Relay Output
2 0 6 4 0 8 1 15 1 0 0 0
Default = Strobe Event Polarity Time Time Base Default = Sirens Event Polarity Time Time Base
(Reset After 8 Hrs) Code Base Multiplier Running Code Base Multiplier

Location 404 405 406 407 408 409

Codepad
Buzzer
0 13 2 1 0 1
Default = Entry/Exit Event Polarity Time Time Base
Warning + Day Code Base Multiplier
Alarm

Event Codes
Event Event
Description Description
Code Code
0 0 BOSCHSAT – Satellite Siren (Output 1 Only) 3 1 Dialler Disabled
0 1 System Armed 3 2 Dialler Active (On-Line)
0 2 System Disarmed 3 3 Ring Detect
0 3 Armed In STAY Mode 3 4 Codepad Panic (Multibreak) V1.05+
0 4 Armed In AWAY 3 5 Mimic Zone 1
0 5 Pre-Arming Alert 3 6 Mimic Zone 2
0 6 Exit Warning (All Zones Sealed) + Entry Warning 3 7 Mimic Zone 3
0 7 Exit Warning 3 8 Mimic Zone 4
0 8 Exit Warning Finished 3 9 Mimic Zone 5
0 9 Kiss-Off After End Of Exit Time 3 10 Mimic Zone 6
0 10 Reserved 3 11 Mimic Zone 7
0 11 Entry Warning 3 12 Mimic Zone 8
0 12 Entry Warning + Day Alarm Resetting 3 13 Reserved
0 13 Exit Warning + Entry Warning + Day Alarm Resetting 3 14 Reserved
0 14 Day Alarm Resetting 3 15 Reserved
0 15 Day Alarm Latching 4 0 Reserved
1 0 Day Alarm Enabled 4 1 Reserved
1 1 Telephone Line Fail 4 2 Reserved
1 2 Kiss-Off Received 4 3 Reserved
1 3 Fuse Fail 4 4 Reserved
1 4 AC Fail 4 5 Chime
1 5 Low Battery 4 6 Zone Not Sealed
1 6 Horn Speaker Fail 4 7 Zone Not Sealed After Exit Time
1 7 Sensor Watch Alarm 4 8 Reserved
1 8 Codepad Medical Alarm 4 9 AC Mains Cycle (60 Hz Or 50 Hz)
1 9 Codepad Fire Alarm 4 10 Area 1 - Zone Unsealed (Solution 880 Only)
1 10 Codepad Panic Alarm 4 11 Area 2 – Zone Unsealed (Solution 880 Only)
1 11 Codepad Duress Alarm 4 12 Reserved
1 12 Access Denied (Code Retries) 4 13 Reserved
1 13 Reserved 4 14 Reserved
1 14 Horn Speaker (Output 1 Only) 4 15 Reserved
1 15 Sirens Running 5 0 Reserved
2 0 Strobe 5 1 Reserved
2 1 Silent Alarm 5 2 Area 1 In Alarm (Solution 880 Only)
2 2 Alarm In STAY Mode 5 3 Area 2 In Alarm (Solution 880 Only)
2 3 Alarm In AWAY Mode 5 4 Reserved
2 4 System Fault 5 5 Reserved
2 5 Fire Alarm (Resetting) 5 6 Area 1 Armed (Solution 880 Only)
2 6 Fire Alarm (Latching) 5 7 Area 2 Armed (Solution 880 Only)
2 7 Fire Alarm (Verification) 5 8 Reserved
2 8 Remote Control 1 5 9 Reserved
2 9 Remote Control 2 5 10 Area 1 Disarmed (Solution 880 Only)
2 10 Remote Control 3 5 11 Area 2 Disarmed (Solution 880 Only)
2 11 Radio Control Output 1 5 12 Reserved
2 12 Radio Control Output 2 5 13 Reserved
2 13 Radio Control Output 1 - Not In AWAY Mode 5 14 Any Areas Armed (Solution 880 Only)
2 14 Radio Control Output 2 - Not In AWAY Mode 5 15 Any Areas Disarmed (Solution 880 Only)
2 15 Communications Fail After 3 Attempts 6 0 Area 1 Codepad Data Terminal (Solution 880 Only)
3 0 Communications Fail 6 1 Area 2 Codepad Data Terminal (Solution 880 Only)

SOL ULTIMA 862 QUICK REF GUIDE.DOCBosch Security Systems Pty Limited
Solution Ultima 862 Quick Reference Guide 15

Polarity (Modes)

Option Description Option Description

0 Disabled
1 Normally Open, Going Low 8 Normally Low, Going Open
2 Normally Open, Pulsing Low 9 Normally Low, Pulsing Open
3 Normally Open, One Shot Low 10 Normally Low, One Shot Open
4 Normally Open, One Shot Low (Reset) 11 Normally Low, One Shot Open (Reset)
5 Normally Open, One Shot Low (Re-trigger) 12 Normally Low, One Shot Open (Re-trigger)
6 Normally Open, One Shot Low (Alarm) 13 Normally Low, One Shot Open (Alarm)
7 Normally Open, Latching Low 14 Normally Low, Latching Open

Time Base
Choose one of the options in the table below for the time base.

Option Description
1 200 ms
2 1 Second
3 1 Minute
4 1 Hour

Time Base Multiplier

Enter a value between 01 – 99.

One Shot Mode

When you program the output polarity as a one shot, the time base is multiplied by the time base multiplier (eg.
If the time base = 2 and the multiplier = 05, the output will operate for 5 seconds)

Pulsing Mode
When you program the output polarity as pulsing, the time base becomes the ‘ON’ time and the multiplier
becomes the ‘OFF’ time. The ‘OFF’ time is the time base x the multiplier (eg. If you want the output to pulse
one (1) second ‘ON’ and five (5) seconds ‘OFF’, you would program time base as one (1) and the multiplier as
five (5)).

SOL ULTIMA 862 QUICK REF GUIDE

16 Solution Ultima 862 Quick Reference Guide

Location 410 - 411

Entry Time 1 Location 410 = Increments Of 1 Second (0 – 15 Seconds)
4 1
Location 411 = Increments Of 16 Seconds (0 – 240 Seconds)
Location 412 - 413
Entry Time 2 Location 412 = Increments Of 1 Second (0 – 15 Seconds)
8 2
Location 413 = Increments Of 16 Seconds (0 – 240 Seconds)
Location 414 - 415
Exit Time (AWAY/STAY Modes) Location 414 = Increments Of 1 Second (0 – 15 Seconds)
12 3
Location 415 = Increments Of 16 Seconds (0 – 240 Seconds)
Location 416 - 417
Entry Guard Time For STAY Mode Location 416 = Increments Of 1 Second (0 – 15 Seconds)
0 0
Location 417 = Increments Of 16 Seconds (0 – 240 Seconds)
Location 418 - 419
Delay Alarm Report Time Location 418 = Increments Of 1 Second (0 – 15 Seconds)
0 0
Location 419 = Increments Of 16 Seconds (0 – 240 Seconds)
Location 420 - 421
Sensor Watch Time Location 420 = Increments Of Days (Tens Digit)
0 0
Location 421 = Increments Of Days (Units Digit)
Location 422
Codepad Lockout Time Location 422 = Increments Of 10 Seconds (0 – 150 Seconds) 0
Location 423
Siren Run Time Location 423 = Increments Of 1 Minute (0 - 15 Minutes)
5
Location 424
Siren Sound Rate Location 424 = (0 = Slowest Frequency / 15 = Fastest Frequency)
7
Location 425
Auto Arming Pre-Alert Time Location 425 = Increments of 5 Minutes (0 – 75 Minutes) 1
Location 426 - 429
Auto Arming Time
Location 426 = Hour Of The Day (Tens Digit) 426 427 428 429
Location 427 = Hour Of The Day (Units Digit)
Location 428 = Minute Of The Day (Tens Digit) 0 0 : 0 0
Location 429 = Minute Of The Day (Units Digit) H H M M

Location 430 - 433

Auto Disarming Time
Location 430 = Hour Of The Day (Tens Digit) 430 431 432 433
Location 431 = Hour Of The Day (Units Digit)
Location 432 = Minute Of The Day (Tens Digit) 0 0 : 0 0
Location 433 = Minute Of The Day (Units Digit) H H M M

Location 434
Kiss-Off Wait Time Location 434 = Increments Of 500 ms (500 ms - 8 Seconds) 3
Location 435
Speaker Beep Volume Location 435 = (0 = No Beeps / 15 = Loudest Beeps) 13
Location 436
System Options 1 1 = BOSCH Smart Lockout Allowed
2 = Horn Speaker Monitor
4 = Strobe Indication For Radio Arm/Disarm
8 = Assign Button 4 On Transmitter To Operate STAY Mode 1
1
Location 437
System Options 2 1 = Codepad Panic To Be Silent
2 = Codepad Fire To Be Silent
4 = Codepad Medical To Be Silent
8 = Access Denied (Code Retries) To Be Silent
0

SOL ULTIMA 862 QUICK REF GUIDE.DOCBosch Security Systems Pty Limited
Solution Ultima 862 Quick Reference Guide 17

Location 438
System Options 3 1 = AC Fail After 1 Hour (Disabled = After 2 Minutes)
2 = Ignore AC Fail
4 = Pulse Count Handover Allowed
8 = Handover Delay To Be Sequential
8
Location 439
System Options 4 1 = Panel To Power Up Disarmed (If Power Reset)
2 = Arm/Disarm Tracking On Power Up
4 = Internal Crystal To Keep Time
8 = Radio Keyswitch Interface, Night Arm Station Or RE005 Installed
0
Location 440
Consumer Options 1 1 = Test Reports Only When Armed
2 = Test Report After Siren Reset
4 = Auto Arm In STAY Mode 1
8 = STAY Indicator To Display Day Alarm Status
0
Location 441
Consumer Options 2 1 = Codepad Display Extinguish After 60 Seconds
2 = Single Button Arming Allowed (AWAY/STAY Mode 1 & 2)
4 = Single Button Disarming Allowed (STAY Mode 1 & 2)
8 = Alarm Memory Reset On Disarm
2
Location 442
Consumer Options 3 1 = Codepad Fault Beeps Allowed
2 = Use Digit 3 For Codepad Duress Alarm (Instead Of Digit 9)
4 = Alarms Activate Sirens and Strobe Outputs In STAY Mode 1 & 2
8 = Zone Tamper Alarms To Be Silent
5
Location 443
Radio Input Options 1 = DS 304Mhz RF Receiver (RF3212)
2 = Latching Keyswitch Input
3 = Momentary Keyswitch Input
4 = Reserved
0
Location 478 - 525
Domestic Telephone Numbers

Location 526
Reserved
0
Location 527
RF Options 1 = Sound Siren On RF Receiver Fail
2 = Sound Siren On RF Receiver Tamper / Jamming
4 = Unseal Zone That Fails Supervision (If Supervision Enabled)
8 = RF Jamming Monitoring Allowed
0
Location 528 - 535
RF Device Mapping Location 528 = Map RF Device 1 To Zone (1 To 8)
For Devices 1 – 8 Location 529 = Map RF Device 2 To Zone (1 To 8)
Location 530 = Map RF Device 3 To Zone (1 To 8)
Location 531 = Map RF Device 4 To Zone (1 To 8)
Location 532 = Map RF Device 5 To Zone (1 To 8) 528 529 530 531 532 533 534 535
Location 533 = Map RF Device 6 To Zone (1 To 8)
Location 534 = Map RF Device 7 To Zone (1 To 8) 1 2 3 4 5 6 7 8
Location 535 = Map RF Device 8 To Zone (1 To 8) D1 D2 D3 D4 D5 D6 D7 D8

Location 536 - 543

RF Device Mapping Location 536 = Map RF Device 9 To Zone (1 To 8)
For Devices 9 – 16 Location 537 = Map RF Device 10 To Zone (1 To 8)
Location 538 = Map RF Device 11 To Zone (1 To 8)
Location 539 = Map RF Device 12 To Zone (1 To 8)
Location 540 = Map RF Device 13 To Zone (1 To 8) 536 537 538 539 540 541 542 543
Location 541 = Map RF Device 14 To Zone (1 To 8)
Location 542 = Map RF Device 15 To Zone (1 To 8) 0 0 0 0 0 0 0 0
Location 543 = Map RF Device 16 To Zone (1 To 8) D9 D10 D11 D12 D13 D14 D15 D16

Location 748 - 749

Ring Burst Time (V1.07+) Location 748 = Increments Of 5 ms (0 – 75 ms)
4 6
Location 749 = Increments Of 80 ms (0 – 1200 ms)

Electronics Design and Manufacturing Pty LimitedSOL ULTIMA 862 QUICK REF GUIDE.D
18 Solution Ultima 862 Quick Reference Guide

Location 801 - 808

RF Signal Strength Location 801 = Signal Strength For RF Device 1
For Devices 1 – 8 Location 802 = Signal Strength For RF Device 2
Location 803 = Signal Strength For RF Device 3
Location 804 = Signal Strength For RF Device 4
Location 805 = Signal Strength For RF Device 5 801 802 803 804 805 806 807 808
Location 806 = Signal Strength For RF Device 6
Location 807 = Signal Strength For RF Device 7 0 0 0 0 0 0 0 0
Location 808 = Signal Strength For RF Device 8 D1 D2 D3 D4 D5 D6 D7 D8

Location 809 - 816

RF Signal Strength Location 809 = Signal Strength For RF Device 9
For Devices 9 - 16 Location 810 = Signal Strength For RF Device 10
Location 811 = Signal Strength For RF Device 11
Location 812 = Signal Strength For RF Device 12
Location 813 = Signal Strength For RF Device 13 809 810 811 812 813 814 815 816
Location 814 = Signal Strength For RF Device 14
Location 815 = Signal Strength For RF Device 15 0 0 0 0 0 0 0 0
Location 816 = Signal Strength For RF Device 16 D9 D10 D11 D12 D13 D14 D15 D16

Location 900
Default Options 0 = Defaulting System Allowed / 15 = Defaulting System Disabled 0
Location 901 - 904
System Time
Location 901 = Hour Of The Day (Tens Digit) 901 902 903 904
Location 902 = Hour Of The Day (Units Digit)
Location 903 = Minute Of The Day (Tens Digit) 0 0 : 0 0
Location 904 = Minute Of The Day (Units Digit) H H M M

Location 905 - 910

System Date Location 905 = Day Of The Month (Tens Digit)
Location 906 = Day Of The Month (Units Digit)
Location 907 = Month Of The Year (Tens Digit) 905 906 907 908 909 910
Location 908 = Month Of The Year (Units Digit)
Location 909 = Current Year (Tens Digit) 0 1 0 1 0 1
Location 910 = Current Year (Units Digit) D D M M Y Y

SOL ULTIMA 862 QUICK REF GUIDE.DOCBosch Security Systems Pty Limited
Solution Ultima 862 Quick Reference Guide 19

Solution Ultima RF Receiver Interface Connections

Figure 1: RF Receiver (RF3212) Wiring Diagram

Wiring and Power Up Operation

- Remove power from the control panel. The following describes the status of the module based on the LED
condition.
- Connect the RF Receiver to the control panel as shown
above using 0.8mm (22-gauge) or larger wire. Wire length LED On – Module is functioning normally.
should not exceed 300 meters (1000 feet). LED Off – Power failure has occurred or module is not wired
correctly.
- Apply power to the control panel. The red LED at the centre LED Turns Off Momentarily – Module acknowledged receiving an
of the module will turn on. RF signal from a remote RF device.

RF Keyfob Operations For Solution Ultima Series Control Panels

Figure 2: RF3332 - 2 Button RF Keyfob Figure 3: RF3332 - 2 Button RF Keyfob

Electronics Design and Manufacturing Pty LimitedSOL ULTIMA 862 QUICK REF GUIDE.D
20 Solution Ultima 862 Quick Reference Guide

Connections For Split EOL Resistors For Six Burglary Zones and Two 24 Hr Zones

Figure 4: Split EOL Wiring Diagram (Location 266 = 15) Figure 5: Split EOL Wiring Diagram With Tamper
(Location 266 = 14)

Connections For Split EOL Resistors Using N/O Contacts

Figure 6: Split EOL Wiring Diagrams Using N/O Contacts

Wiring Diagram For Keyswitch Zone

Figure 7: Wiring Diagram For Keyswitch Zone

SOL ULTIMA 862 QUICK REF GUIDE.DOCBosch Security Systems Pty Limited
Solution Ultima 862 Quick Reference Guide 21

Wiring Diagram

Figure 8: Solution Ultima Series Wiring Diagram

Electronics Design and Manufacturing Pty LimitedSOL ULTIMA 862 QUICK REF GUIDE.D
22 Solution Ultima 862 Quick Reference Guide

Component Overlay

Figure 9: Solution Ultima Series Component Overlay

SOL ULTIMA 862 QUICK REF GUIDE.DOCBosch Security Systems Pty Limited