Search Results (4,268)

Fe(III) oxides were prepared as free nanoparticles and on DNA templates via the precipitation of Fe(III) salts with NaOH in the presence/absence of DNA. Through control of the pH and temperature, FeOOH and Fe2O3 were synthesised. The formation of templated materials FeOOH /DNA and Fe2O3 /DNA was confirmed using UV-Vis absorption and FTIR spectra. The direct optical gap of Fe2O3 /DNA was estimated as 3.2 eV; the absorption by FeOOH /DNA and Fe2O3 /DNA at longer wavelengths is weaker, but consistent with indirect gaps near 2 eV. X-ray photoelectron spectra confirmed the presence of Fe(III) and DNA in the templated samples. Analysis of the X-ray diffraction patterns of both templated and non-templated FeOOH and Fe2O3 demonstrated that the materials were the α-FeOOH and α-Fe2O3 polymorphs with crystallite diameters of the DNA-templated materials estimated as 7.6 nm and 6.8 nm. Transmission electron microscopy showed needle-like crystals of both FeOOH and Fe2O3, but the Fe2O3 contains some globular structures. In contrast, the morphology of FeOOH /DNA and Fe2O3 /DNA consists of needle-like crystallites of the respective oxides organised into complex dendritic structures with a length on the 10 μm scale formed by the DNA molecules. Finally, scanned conductance microscopy provided evidence for the conductivity of the FeOOH /DNA after alignment via molecular combing on an Si/SiO2 substrate. Fe2O3 /DNA did not exhibit any detectable conductivity. Full article

Mesoporous titania nanoparticles (NPs) can be used for encapsulation polyphenols, with applications in the food industry, cosmetics, or biomedicine. TiO₂ NPs were synthesized using the sol-gel method combined with solvothermal treatment. TiO₂ NPs were characterized through X-ray diffraction, FTIR spectroscopy, the N₂ adsorption method, scanning and transmission electron microscopy, and thermal analysis. The sample prepared using Pluronic F127 presented a higher surface area and less agglomerated NPs than the samples synthesized with Pluronic P123. Grape marc (GM), a by-product from wine production, can be exploited for preparing extracts with good antioxidant properties. In this regard, we prepared hydroethanolic and ethanolic GM extracts from two cultivars, Feteasca Neagra (FN) and Pinot Noir. The extract components were determined by spectrometric analyses and HPLC. The extract with the highest radical scavenging activity, the hydroethanolic FN extract, was encapsulated in titania (FN@TiO₂) and compared with SBA-15 silica support. Both resulting materials showed biocompatibility on the NCTC fibroblast cell line in a 50–300 µg/mL concentration range after 48 h of incubation and even better radical scavenging potential than the free extract. Although titania has a lower capacity to host polyphenols than SBA-15, the FN@TiO₂ sample shows better cytocompatibility (up to 700 µmg/mL), and therefore, it could be used for skin-care products. Full article

Tetrataenite is a promising candidate for rare earth-free permanent magnets due to its low cost and intrinsic magnetic properties. This work investigates the effect of combined milling at liquid nitrogen temperatures (cryomilling) and the addition of carbon as an interstitial element for promoting the formation of tetrataenite. Crystal structure, microstructure, and magnetic properties are investigated to understand the influence of mechanical processing and compositional modifications. No unambiguous evidence of the ordered phase of tetrataenite is found in the structural characterization. However, using Scanning Transmission Electron Microscopy (STEM) and powder X-ray diffraction (PXD) analyses, the occurrence of both twinning and stacking faults resulting from the high-energy milling process is observed, which is a relevant factor for identifying tetrataenite in FeNi alloys. The probability of a stacking fault and twinning occurring for a carbon-free FeNi sample before annealing is found to be 2% and 1.4%, respectively. After annealing, the stacking fault probability decreased to 1.2%, while that of twinning was 1.4%. By increasing the carbon concentration to 5 at.%, the stacking faults and twinning probabilities decrease slightly to 1.2% and 1.3%, respectively. The occurrence of stacking faults combined with small crystallite sizes was a hindering factor in identifying the presence of tetrataenite. Full article

Additive friction stir deposition (AFS-D) is considered a productive method of additive manufacturing (AM) due to its ability to produce dense mechanical parts at a faster deposition rate compared to other AM methods. Al6061 alloy finds extensive application in aerospace and nuclear engineering; nevertheless, exposure to radiation or high-energy particles over time tends to deteriorate their mechanical performance. However, the effect of radiation on the components manufactured using the AFS-D method is still unexamined. In this work, samples from the as-fabricated Al6061 alloy, by AFS-D, and the Al6061 feedstock rod were irradiated with He+ ions to 10 dpa at ambient temperature. The microstructural and mechanical changes induced by irradiation of He+ were examined using a scanning electron microscope (SEM), energy-dispersive X-ray spectroscopy (EDS), transmission electron microscopy (TEM), and nanoindentation. This study demonstrates that, at 10 dpa of irradiation damage, the feedstock Al6061 produced a bigger size of He bubbles than the AFS-D Al6061. Nanoindentation analysis revealed that both the feedstock Al6061 and AFS-D Al6061 samples have experienced radiation-induced hardening. These studies provide a valuable understanding of the microstructural and mechanical performance of AFS-D materials in radiation environments, offering essential data for the selection of materials and processing methods for potential application in aerospace and nuclear engineering. Full article

Indazoles have previously been identified as molecules with antiprotozoal activity. In this study, we evaluate the in vitro activity of thirteen 3-alkoxy-1-benzyl-5-nitroindazole derivatives (series D) against L. amazonensis, L. infantum, and L. mexicana. In vitro, cytotoxicity against mouse peritoneal macrophages and growth inhibitory activity in promastigotes were evaluated for all compounds, and those showing adequate activity and selectivity were tested against intracellular amastigotes. Transmission and scanning electron microscopy were employed to study the effects of 3-alkoxy-1-benzyl-5-nitroindazole and 2-benzyl-5-nitroindazolin-3-one derivatives on promastigotes of L. amazonensis. Compounds NV6 and NV8 were active in the two life stages of the three species, with the latter showing the best indicators of activity and selectivity. 3-alkoxy-1-benzyl-5-nitroindazole derivatives (series D) showed in vitro activity comparable to that of amphotericin B against the promastigote stage of Leishmania spp. Two compounds were also found to be active the amastigote stage. Electron microscopy studies confirmed the antileishmanial activity of the indazole derivatives studied and support future research on this family of compounds as antileishmanial agents. Full article

Oriented antibody immobilization has been widely employed in immunoassays and immunodiagnoses due to its efficacy in identifying target antigens. Herein, a heptapeptide ligand, HWRGWVC (HC7), was coupled to poly(glycidyl methacrylate) (PGMA) nanospheres (PGMA-HC7). The antibody immobilization behavior and antigen recognition performance were investigated and compared with those on PGMA nanospheres by nonspecific adsorption and covalent coupling via carbodiimide chemistry. The antibodies tested included bovine, rabbit, and human immunoglobulin G (IgG), while the antigens included horseradish peroxidase (HRP) and β-2-Microglobulin (β2-MG). The nanospheres were characterized using zeta potential and particle size analyzers, scanning electron microscopy, transmission electron microscopy, Fourier transform infrared spectroscopy, and reversed-phase chromatography, proving each synthesis step was succeeded. Isothermal titration calorimetry assay demonstrated the strong affinity interaction between IgG and PGMA-HC7. Notably, PGMA-HC7 achieved rapid and extremely high IgG adsorption capacity (~3 mg/mg) within 5 min via a specific recognition via HC7 without nonspecific interactions. Moreover, the activities of immobilized anti-HRP and anti-β2-MG antibodies obtained via affinity binding were 1.5-fold and 2-fold higher than those of their covalent coupling counterparts. Further, the oriented-immobilized anti-β2-MG antibody on PGMA-HC7 exhibited excellent performance in antigen recognition with a linear detection range of 0–5.3 μg/mL, proving its great potential in immunoassay applications. Full article

Nanostructured ferritic alloys (NFAs), such as oxide-dispersion strengthened (ODS) alloys, play a vital role in advanced fission and fusion reactors, offering superior properties when incorporating nanoparticles under irradiation. Despite their importance, the high cost of mass-producing NFAs through mechanical milling presents a challenge. This study delves into the microstructure-mechanical property correlations of three NFAs produced using a novel, cost-effective approach combining severe plastic deformation (SPD) with the continuous thermomechanical processing (CTMP) method. Analysis using scanning electron microscopy (SEM)-electron backscatter diffraction (EBSD) revealed nano-grain structures and phases, while scanning transmission electron microscopy (STEM)-energy dispersive X-ray spectroscopy (EDS) quantified the size and density of Ti-N, Y-O, and Cr-O fine particles. Atom probe tomography (APT) further confirmed the absence of finer Y-O particles and characterized the chemical composition of the particles, suggesting possible nitride dispersion strengthening. Correlation of microstructure and mechanical testing results revealed that CTMP alloys, despite having lower nanoparticle densities, exhibit strength and ductility comparable to mechanically milled ODS alloys, likely due to their fine grain structure. However, higher nanoparticle densities may be necessary to prevent cavity swelling under high-temperature irradiation and helium gas production. Further enhancements in uniform nanoparticle distribution and increased sink strength are recommended to mitigate cavity swelling, advancing their suitability for nuclear applications. Full article

In this work, two different composite nanostructures, YAG:Ce and Ga_0.9In_0.1N, were prepared by the Urea Glass Route method and tested for the production of white light. The first composite was prepared by synthetizing the Ga_0.9In_0.1N nanoparticles in the presence of YAG:Ce nanoparticles. The second one was prepared by synthetizing YAG:Ce nanoparticles in the presence of Ga_0.9In_0.1N nanoparticles. These systems can be useful for the production of white light. X-ray Diffraction and Transmission and Scanning Electron Microscopies (TEM and SEM) were used to evaluate their structural and morphological properties. Excitation and emission spectra, the quantum yield and colour of the emitted light were acquired to evaluate the optical properties of the systems. Full article

This study utilized a bobbin tool to friction stir weld aluminum 6082 workpieces under two sets of process parameters: a tool rotation speed of 280 rev/min with a weld velocity of 280 mm/min (280/280) and a tool rotation speed of 450 rev/min with a weld velocity of 450 mm/min (450/450). The weld microstructures were characterized through optical microscopy utilizing polarized light and through transmission electron microscopy (TEM) and scanning electron microscopy (SEM) coupled with chemical analysis by energy dispersive spectroscopy and electron back scatter diffraction. The microstructural studies were supplemented by hardness measurements (Vickers) performed on the same sections as the metallographic examinations. The produced weldments were free from cracks and any discontinuities. Fine, equiaxed grains that were several microns in size characterized the stir zones (SZs), and the advancing (AS) and retreating (RS) sides revealed distinct microstructural features. On the AS, the transition from the thermo-mechanically affected zone to the SZ was well defined and sharp, but on the RS, the transition appeared as a continuous, gradual change in microstructure. The lower weld energy (280/280) produced lower hardness in the stir zone than the higher energy weld (450/450), ~95 HV1 versus ~115 HV1; however, the 280/280 welds showed higher tensile strengths than the 450/450 welds, ~238 MPa as opposed to ~172 MPa. These behaviors in mechanical performance correlated with the temperature histories produced by each set of weld parameters in relation to the precipitation behavior of the alloy. The fracture characteristics of the weldments were notably different with the 450/450 sample fracturing in a quasi-brittle manner with slight plastic deformation and the 280/280 sample fracturing ductilely. A numerical simulation supported the investigation by elucidating the temperature and material flow behavior during the joining process. Full article

Chondrules are tiny particles that occur in stony meteorites and are considered as the building blocks of early asteroids and planets. It is believed that they were formed by the fast heating of the dust in the solar nebula. To date, there is no lab-scale experimental study of the formation of chondrules from the initial gas phase precursors following fast heating and crystallisation. The motivation of this work is a pre-trial study of the formation of chnodrule-like particles. The formation of meteorites in the space environment is associated with the aggregation of small particles or molecular clouds under the influence of shock waves or high-energy gas discharges in the solar nebula. In this work, the properties of product formation at the nanoscale-level were investigated using different feedstock materials which are the dominant elements in the meteorite. The structural and morphological properties of the synthesised Si-Fe nanomaterials were analysed by scanning/transmission electron microscopy (SEM/TEM), and chemical composition was analysed by X-ray energy-dispersive spectroscopy (EDS). The identification of crystalline phases was carried out by X-ray diffraction (XRD), whereas the presence of an Fe-Si system in the synthesised particles was demonstrated by Mössbauer spectroscopy. The obtained materials were exposed to the relatively high-energy pulsed plasma beam on the substrate with the aim to emulate the possible fast heating and melting of the formed nanoparticles. The formation steps of growing synthetic (engineered) chondro-like particles and nanostructures in laboratory conditions is discussed. Full article

This work describes a novel method for converting bismuth triiodide (BiI₃) microplates into bismuth oxyiodide (BiOI) nanoflakes under ultrasonic irradiation. To produce BiOI nanoflakes with a high yield and high purity, the conversion process was carefully adjusted. Rapid reaction kinetics and increased mass transfer are benefits of the ultrasonic-assisted approach that result in well-defined converted BiOI nanostructures with superior characteristics. The produced BiOI nanoflakes were examined utilizing a range of analytical methods, such as Transmission Electron Microscopy (TEM), scanning electron microscopy (SEM) and X-ray diffraction (XRD). The progress in the ultrasonic conversion process with time was monitored through diffuse reflectance spectroscopy (DRS). The outcomes demonstrated the effective conversion of BiI₃ microplates into crystalline, homogeneous, high-surface-area BiOI nanoflakes. Additionally, the degradation of organic dyes (methylene blue) under ultraviolet (UV) light irradiation was used to assess the photocatalytic efficacy of the produced BiOI nanoflakes. Because of their distinct morphology and electrical structure, the BiOI nanoflakes remarkably demonstrated remarkable photocatalytic activity, outperforming traditional photocatalysts. The ability of BiOI nanoflakes to effectively separate and utilize visible light photons makes them a viable option for environmental remediation applications. This work not only shows the promise of BiOI nanoflakes for sustainable photocatalytic applications but also demonstrates a simple and scalable approach to their manufacturing. The knowledge gathered from this work opens up new avenues for investigating ultrasonic-assisted techniques for creating sophisticated nanomaterials with customized characteristics for a range of technological uses. Full article

This paper focuses on the wear resistance performance of Ni-SiC composite coatings with various contents of SiC particles. The coatings were characterized via a scanning electron microscope (SEM), X-ray diffractometer (XRD), and transmission electron microscopy (TEM), and the wear behaviors of different coatings were tested. The results show that SiC particle incorporation results in a nanocrystalline metal matrix and nanotwins in nickel nanograins. The microhardness and wear resistance Ni-SiC composite coatings increased with the increasing SiC content. Microhardness was improved due to the grain-refinement strengthening effect and the presence of a nanotwin structure. The dominant wear mechanism was described in two stages: the first stage involves the interaction of SiC particles/the counter ball, and the second stage involves the formation of the oxide film its breaking up into wear debris. A higher SiC content increased the duration of the first stage and slowed down the rate of breaking up into debris, thereby decreasing the wear rate. Full article

This study investigates the microstructural evolution and mechanical properties of high-nickel shipbuilding steel during thermal processing using high-temperature confocal laser-scanning microscopy (HTCLSM). An in situ observation of the heating and holding processes reveals critical insights into phase transformations, grain-growth behavior, and the formation of precipitates. The experimental results demonstrate that austenitization begins at approximately 700 °C, with significant grain-boundary nucleation. At 900 °C, the formation of black precipitates was observed, and their persistence up to temperatures exceeding 1000 °C was confirmed. Scanning electron microscopy (SEM) and energy-dispersive spectroscopy (EDS) analyses identified these precipitates as chromium carbides (Cr₇C₃), which significantly contribute to the material’s strength. A comprehensive analysis using transmission electron microscopy (TEM) confirmed the presence and distribution of Cr₇C₃ within the grains and along grain boundaries. These findings provide a deeper understanding of the microstructural dynamics in high-nickel steels, guiding the optimization of heat-treatment processes to enhance mechanical properties for maritime applications. Full article

The Ni-GQDs composite plating was created using direct current (DC), single-pulse, and double-pulse power supplies, with GQDs serving as additives under supercritical CO₂ conditions. A comparative analysis was conducted to evaluate the effects of different electrodeposition power sources on the microstructure and properties of the Ni-GQDs composite plating. High-Resolution Transmission Electron Microscopy (HRTEM) was employed to investigate the distribution of GQDs within the composite plating as well as to analyze d-spacing and diffraction patterns. Scanning Electron Microscopy (SEM) was utilized to illustrate the surface morphology of the plating and assess its surface quality. The grain size and preferred orientation of the plated layer were examined using X-ray Diffraction (XRD), while Atomic Force Microscopy (AFM) was used to evaluate the roughness of the surface. To compare the abrasion resistance of the various plating types, wear amounts and friction coefficients were measured through friction and wear tests. Additionally, corrosion resistance tests were performed to assess the corrosion resistance of each plating variant. The results indicate that the Ni-GQDs-III composite layers produced via double-pulse electrodeposition exhibit superior surface quality, characterized by smaller grain sizes, enhanced surface flatness, reduced surface roughness, and improved resistance to wear and corrosion. Full article

The Phytoseiulus persimilis specialized in preying on Tetranychus species, with particularly strong predation capability against Tetranychus urticae. To investigate the morphology of female reproductive structures and effects of different gravid times on structures of oocytes and embryos in Phytoseiulus persimilis, we employed paraffin sectioning, transmission electron microscopy (TEM), and scanning electron microscopy (SEM) on the model species of predatory mite Phytoseiulus persimilis. The female adult possessed several reproductive organs, including paired solenostomes, major ducts, embolus, calyces, and vesicles within the sperm-access system, as well as lyrate organ and the ovary. Furthermore, the reproductive system also encompassed the uterus, vagina, and genital pore, which were involved in egg development and expulsion. The solenostomes were situated between the third and fourth legs, and they were scarcely discernible in virgin, but they became apparent during mating. The occurrence of mating significantly influenced the nucleus of lyrate organ. In virgin, the nucleus exhibited underdeveloped morphology, whereas in mated individuals, it was well-formed. However, the duration of mating did not impact its development. The cellular structure of the ovary was solely associated with the stage of the surrounding oocyte and was not directly linked to mating occurrences. The uterus was barely visible outside of mating periods but became observable 12 h after mating when eggs were present within the body. At this point, it opened in preparation for egg laying when both the vagina and reproductive opening were open. Positioned in front of the vesicle but behind the ovary was the lyrate organ, with its lower part housing the uterus. The vagina was connected to the genital pore. No significant difference was observed in oocyte morphology between the virgin ovaries and the mated. Oocyte development occurred through four stages: during stage I (4–9 h after mating), yolk accumulation took place; stage II (10 h after mating) involved egg relocation; stage III (12–13 h after mating) was marked by eggshell formation; finally, at stage IV (14–16 h after mating), embryonic development commenced, leading to egg deposition. The fusion of sperm and egg occurred approximately 9–10 h after mating. These findings established a solid foundation for investigating the Phytoseiid reproductive mechanisms. Full article