Scribd
Upload
112 views5 pages

QuestionPaper Import Sample

The document outlines a series of engineering design problems related to joints, columns, couplings, and keys, each requiring calculations based on material properties and safety factors. It includes specific tasks such as designing a cotter joint, a hollow circular column, and determining bolt diameters for rigid couplings. Additionally, it discusses various types of keys with sketches and provides a framework for applying ASME code for shaft diameter determination.

Uploaded by

riteshkirdak
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as XLSX, PDF, TXT or read online on Scribd
112 views5 pages

QuestionPaper Import Sample

The document outlines a series of engineering design problems related to joints, columns, couplings, and keys, each requiring calculations based on material properties and safety factors. It includes specific tasks such as designing a cotter joint, a hollow circular column, and determining bolt diameters for rigid couplings. Additionally, it discusses various types of keys with sketches and provides a framework for applying ASME code for shaft diameter determination.

Uploaded by

riteshkirdak
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as XLSX, PDF, TXT or read online on Scribd

QuestionNo QuestionDescription CO Mapped

Q-1 (a) Explain the steps for design of Cotter Joint. CO-1,

A knuckle joint is subjected to an axial load of 25KN.It


is made of Plain carbon steel 45C8 (S =380 N/mm2).
Design the joint with factor of safety
Q-1 (b) CO-1,
2.5. Assume the compressive strength of the material
to be 20% more than tensile strength. Allowable shear
stress is 0.517 of the allowable tensile stress.

Q2) a) Explain Lever, its types with neat sketch and CO-1,
applications.
A hollow circular column carries a projecting bracket.
Which supports a load of 25kN as shown in Figure 1.
The distance between the axis of the column and load
is 500 mm. The inner diameter of the column is 0.8
times of the outer diameter. The column is made of
steel FeE200 (S =200N/mm2) and the factor of safety
is 4. The column is to be designed on the basis of
maximum tensile stress and compression is not the
criterion of failure. Determine the dimensions of the
cross section of the column

Q2) b) CO-1,

Q3) a) Explain the design Procedure for Flexible Coupling CO-2


Compute diameter of bolt for rigid coupling is used to
transmit 20 kW power at 720 rpm. There are four
bolts and the pitch circle diameter of
the bolts is 125 mm. The bolts are made of steel 45C8
(Syt =380 N/mm2)and the factor of safety is 3.
Q3) b) Assueme that bolts are finger tight in reamed and CO-2
ground holes. Permissible stress is taken as 0.577
times yield stress.

Explain the following keys with suitable sketch i)Sunk


Key ii) Saddle Key iii)Kenndey key
Q4) a) CO-2
Explain the following keys with suitable sketch i)Sunk
Key ii) Saddle Key iii)Kenndey key
Q4) a) CO-2

The layout of an intermediate shaft of a gear box


supporting two spur gears B and C is shown in Figure
2. The shaft is mounted on two bearings A and D. The
pitch circle diameters of gears B and C are 900 and
600 mm respectively.The material of the shaft is steel
FeE 580 (Sut = 770 and Syt = 580 N/mm2)The factors
kb and kt of ASME code are 1.5 and 2.0 respectively.
Determine the shaft diameter using the ASME
codeAssume that the gears are connected to the shaft
by means of keys thus permissible shear stress is
103.95 N/mm.
Q4) b) CO-2
BloomsTaxonomy MaxMarks
Remember,Analyse 6

Remember,Analyse 9

6
Remember,Analyse

Remember,Analyse 9

Remember,Analyse 9

Remember,Analyse 6

Remember,Analyse 6
Remember,Analyse 6

Remember,Analyse 9
CO's Bloom's
CO-1 Remember
CO-2 Understand
CO-3 Apply
CO-4 Analyse
CO-5 Evaluate
CO-6 Create

You might also like