Pole Pitch

Pole Pitch
Definition of Pole Pitch

The pole pitch is defined as peripheral distance between center of two adjacent poles in dc
machine. This distance is measured in term of armature slots or armature conductor come
between two adjacent pole centers.
This is naturally equal to the total number of armature slots divided by number of poles in the
machine.
If there are 96 slots on the armature periphery and 4 numbers of poles in the machine, the
numbers of armature slots come between two adjacent poles centers would be 96/4 = 24.
Hence, the pole pitch of that dc machine would be 24.
As it is seen that, pole pitch is equal to total numbers of armature slots divided by total
numbers of poles, this can alternatively referred as armature slots per pole.
Coil Span or Coil Pitch

Coil of dc machine is made up of one turn or multi turns of the conductor. If the coil is made
up of single turn or single loop of conductor, it is called single turn coil. If the coil is made up
of more than one turn of conductor, it is referred as multi turn coil. A single turn coil will
have one conductor per side of the coil whereas in multi turns coil, there will be multiple
conductors per side of the coil. Whatever may be the number of conductors per side of the
coil, each coil side is placed inside one armature slot only. That means all conductors of one
side of a particular coil must be placed in one single slot only. Similarly, all conductors of
other side of the coil are placed in another single armature slot.
Definition of Coil Span

Coil span is defined as peripheral distance between two sides of a coil, measured in terms of
number of armature slots between them. That means, after placing one side of the coil in a
particular slot, after how many conjugative slots, the other side of the same coil is placed on
the
armature.
This
number
is
known
as
coil
span.
If the coil span is equal to the pole pitch, then the armature winding is said to be full pitched. At this situation, two opposite sides of the coil lie under two opposite poles. Hence
emf induced in one side of the coil will be in 180 phase shift with emf induced in the other
side of the coil. Thus, total terminal voltage of the coil will be nothing but the direct
arithmetic sum of these two emfs.
If the coil span is less than the pole pitch, then the winding is referred as fractional pitched. In
this coil, there will be a phase difference between induced emfs in two sides, less than 180.
Hence resultant terminal voltage of the coil is vector sum of these two emfs and it is less than
that of full-pitched coil.
In practice, coil pitch (or Span) as low as eight tenth of a Pole Pitch, is employed without
much serious reduction in emf. Fractional pitched windings are purposely used to effect
substantial saving in copper of the end connection and for improving commutation.
Pitch of Armature Winding
Back Pitch (Yb)

A coil advances on the back of the armature. This advancement is measured in terms of
armature conductors and is called back pitch. It is equal to the number difference of the
conductor connected to a given segment of the commutator.
Front Pitch (Yf)

The number of armature conductors or elements spanned by a coil on the front is called front
pitch.
Alternatively, the front pitch may be defined as the distance between the second conductor
of the next coil which are connected together at the front i.e. commutator end of the armature.
In other words, it is the number difference of the conductors connected together at the back
end of the armature. Both front and back pitches for lap and wave windings are shown in the
figure below.
Resultant Pitch (Y)

It is the distance between the beginning of one coil and the beginning of the next coil to
which it is connected.
As a matter of precautions, it should be kept in mind that all these pitches, though normally
stated in terms of armature conductors, are also times of armature slots or commutator bars.
Commutator Pitch
Commutator pitch is defined as the distance between two commutator segments which two
ends of same armature coil are connected. Commutator pitch is measured in terms of
commutator bars or segment.
Single Layer Armature Winding

Armature coil sides are placed in the armature slots in different manner. In some
arrangement, each slot is occupied by one side of an armature coil. In other words one coil
sides is placed in each armature slot. This arrangement is referred as single layer winding.
Two Layer Armature Winding

In other types of armature winding, arrangement every armature slot is occupied by two coil
sides, one on upper half and other on lower half of the slot. The coils in two layers winding
are so placed, that if one side is placed on upper half of the slot then other side is placed on
the lower half of some other slot at a distance of one coil pitch away.

Pole Pitch

Uploaded by

Copyright:

Available Formats

Pole Pitch

Uploaded by

Document Information

Original Description:

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Pole Pitch

Uploaded by

Copyright:

Available Formats

Pole Pitch

Definition of Pole Pitch

Coil Span or Coil Pitch

Definition of Coil Span

Pitch of Armature Winding

Back Pitch (Yb)

Front Pitch (Yf)

Resultant Pitch (Y)

Single Layer Armature Winding

Two Layer Armature Winding

You might also like