Sustainable Recycling and Reuse of Industrial By-Products or Waste from Geo-Resource Exploitation

Sewage sludge (SS), a byproduct of wastewater treatment plants, poses significant environmental and health risks if not properly handled. Conventional approaches for SS stabilization often involve costly and energy-consuming processes. This study investigated the effect of promoting native microalgae growth in SS on its stabilization, pathogen bacteria removal, and valuable biomass production. The effect on settleability, filterability, and extracellular polymeric substances (EPSs) was examined as well. Experiments were conducted in photobioreactors (PBRs) without O₂ supply and CO₂ release under controlled parameters. The results show a significant improvement in SS stabilization, with a reduction of volatile solids (VSs) by 47.55%. Additionally, fecal coliforms and E. coli were efficiently removed by 2.25 log and 6.72 log, respectively. Moreover, Salmonella spp. was not detected after 15 days of treatment. The settleability was improved by 71.42%. However, a worsening of the sludge filterability properties was observed, likely due to a decrease in floc size following the reduction of protein content in the tightly bound EPS fraction. Microalgae biomass production was 16.56 mg/L/day, with a mean biomass of 0.35 g/L at the end of the batch treatment, representing 10.35% of the total final biomass. These findings suggest that promoting native microalgal growth in SS could be sustainable and cost-effective for SS stabilization, microalgal biomass production, and the enhancement of sludge-settling characteristics, notwithstanding potential filtration-related considerations. Full article

This study investigates the potential of utilizing industrial by-products—mill scale (MS) and aluminum dross (AD)—as sources of Fe₂O₃ and Al₂O₃, respectively, for hercynite (FeAl₂O₄) production. Through combustion of MS-AD-graphite systems at 1550 °C under air atmosphere, hercynite-based refractory materials were synthesized. Results confirm the viability of this upcycling approach for hercynite synthesis. During the formation of hercynite, the development of a dendritic structure can be observed, which subsequently fuses into a grain shape. XRD phase analysis using the Rietveld method revealed that the major components of the product with a C/O ratio of 1 were 85.11% FeAl₂O₄, 10.99% Al₂O₃, and 3.9% C. For the product with a C/O ratio of 2, the composition was 82.4% FeAl₂O₄, 13.0% Al₂O₃, and 4.6% C. The combustion of raw pellets with a C/O ratio of 1 at 1550 °C for 1 h in a normal air atmosphere is economically viable for producing hercynite, yielding 85.11 wt%. This approach presents a sustainable and eco-friendly alternative to using commercial raw materials, potentially eliminating the need for virgin alumina and iron ore. By repurposing waste materials from the steel and aluminum industries, this study contributes to the circular economy and aligns with the goal of zero waste. Full article

The circular economy, driven by waste elimination, material circulation and nature regeneration, is crucial for business, people, and the environment. With the increasing demand for distilled beverages, managing agricultural waste like spent grains is paramount. While previous studies focused on individual beverages, investigating technologies across different types of beverages has been overlooked. This paper provides a systematic review of agricultural waste valorisation over the past five years, focusing on four representative distilled beverages: whisk(e)y, tequila, baijiu and shochu. Research efforts have primarily focused on bioenergy production from whisk(e)y and tequila waste, whereas extracting functional substances is common for baijiu and shochu. Through integrating different technologies, a “Three-level Valorisation System” was proposed to enhance the translation of agricultural waste into value-added products like proteins. This system is directly relevant to the distilled beverage industry globally and applicable to associated industries such as biofuel and food production. Full article

The aim of this work was to study the purification of silicon kerf loss waste (KLW) by a combination of single-acid leaching followed by inductive melting at high temperatures with an addition of fluidized bed reactor (FBR) silicon granules. The KLW indicated an average particle size (D50) of approximately 1.6 µm, and a BET surface area of 30.4 m²/g. Acid leaching by 1 M HCl indicated significant removal of impurities such as Ni (77%), Fe (91%) and P (75%). The combined two-stage treatment resulted in significant removal of the major impurities: Al (78%), Ni (79%), Ca (85%), P (92%) and Fe (99%). The general material loss during melting decreased with an increasing amount of FBR silicon granules which aided in the melting process and indicated better melting. It was observed that the melting behavior of the samples improved as the temperature increased, with complete melting being observed throughout the crucibles at the highest temperature (1800 °C) used, even without any additives. At lower temperatures (1600 °C–1700 °C) and lower FBR-Si (<30 wt.%) additions, the melting was incomplete, with patches of molten silicon and a lot of surface oxidation as confirmed by both visual observation and electron microscopy. In addition, it was indicated that more reactive and volatile elements (Ga, Mg and P) compared to silicon are partially removed in the melting process (51–87%), while the less reactive elements end up in the final silicon melt. It was concluded that if optimized, the combined treatment of single-acid leaching and inductive melting with the addition of granular FBR silicon has great potential for the recycling of KLW to solar cells and similar applications. Moreover, the application of higher melting temperatures is accompanied by a higher silicon yield of the process, and the involved mechanisms are presented. Full article

This paper presents the characterization of a binary mixture of construction and demolition waste (CDW) and bamboo leaf ash (BLAsh) calcined at 600 °C (novel mixture) and the study of its pozzolanic behavior. Different dosages in a pozzolan/Ca(OH)₂ system were employed. The aim is the valorization of fine-fraction CDW that achieves a more reactive binary mixture and allows an adequate use of CDW as waste, as CDW is a material of limited use due to its low pozzolanic activity. The pozzolanic behavior of the mixture was analyzed using the conductometric method, which measures the electrical conductivity in the CDW + BLAsh/CH solution versus reaction time. With the application of a kinetic–diffusive mathematical model, the kinetic parameters of the pozzolanic reaction were quantified. This allowed a quantitative evaluation of the pozzolanic activity based on the values of these parameters. To validate these results, other experimental techniques were used: X-ray diffraction, thermogravimetry and scanning electron microscopy. Also, mechanical compressive strength assays were carried out. The results show an increase in the pozzolanic activity of binary mixes of CDW + BLAsh for all the dosages used in comparison to the pozzolanic activity of CDW alone. The quantitative assessment (kinetic parameters) shows that the binary mixture CDW50 + BLAsh50 is the most reactive (reaction rate constant of 7.88 × 10⁻¹ h⁻¹) and is superior to the mixtures CDW60 + BLAsh40 and CDW70 + BLAs30. Compressive strength tests show higher strength values for the ternary mixes (OPC + CDW + BLAsh) compared to the binary mixes (OPC + CDW). In view of the results, the binary blend of pozzolans CDW + BLAsh is suitable for the manufacture of future low-carbon ternary cements. Full article

Critical raw materials (CRMs) supply is a challenge that EU countries have to face, with many thinking about domestic procurement from natural ore deposits and anthropogenic deposits (landfills and extractive waste facilities). The present research focuses on the possibilities linked to the supply of CRMs and the potential for exploiting rare earth elements (REEs), investigating a large variety of extractive waste and siliceous rocks in the Piedmont region (Northern Italy). Indeed, the recovery of REEs from the extractive waste (EW) of siliceous quarries and other siliceous ore deposits can be a valuable way to reduce supply chain risks. Starting with a review of the literature on mining activities in Piedmont and continuing with the sampling and geochemical, mineralogical, petrographic, and environmental characterization of EW facilities connected to siliceous dimension stones, of kaolinitic gneiss ore deposits, and of soils present near the investigated areas, this study shows that the degree of REEs enrichment differs depending on the sampling area (soil or EW) and lithology. The concentration of REEs in the EW at some sampling sites fulfils the indicators of industrial-grade and industrial recovery; the high cumulative production and potential market values of EW and the positive recovery effects through proven methodologies indicate a viable prospect of REE recovery from EW. However, REE recovery industrialization faces challenges such as the difficulty in achieving efficient large-scale recovery due to large regional differences in REE abundance, the mismatch between potential market value and waste annual production, etc. Nonetheless, in the future, EW from dimension stone quarries could be differentially studied and reused based on the enrichment and distribution characteristics of trace elements. The present paper shows investigation procedures undertaken to determine both CRMs potentialities and environmental issues (on the basis of literature data employed to select the more-promising areas and on sampling and characterization activities in the selected areas), together with procedures to determine the waste quantities and tentative economic values of REEs present in the investigated areas. This approach, tested on a large area (Piedmont region), is replicable and applicable to other similar case studies (at EU and non-EU levels) and offers decision makers the possibility to acquire a general overview of the potential available resources in order to decide whether and where to concentrate efforts (including economic ones) in a more detailed study to evaluate the exploitable anthropogenic deposits. Full article

Steel slags are solid residual materials formed as by-products throughout the process of steel production within the steelmaking industry. These wastes have good physical properties such as high stiffness and friction angle for use as road fill materials or in geotechnical applications. However, the presence of heavy metals and high alkalinity levels constitute significant environmental hazards and set limitations on using slags in engineering applications. While there have been investigations into the mechanical characteristics of steel slags, research on assessing potential harm when utilizing the materials in engineering applications is rare. This study examines the mitigation methods to address the environmental problems associated with steel slags. To do this, two different steel slags with different production techniques were treated with soils of different properties such as fine and coarse sand, bentonite, kaolin, and natural clay. The pH and electrical conductivity (EC) values of pure steel slags were determined using the water leach test (WLT). Variations in pH and EC values of steel slags subjected to treatment were evaluated through both WLT and sequential water leach (SWLT) tests. As a result, the high strength, stiffness, and drainage capability of EAF and LS steel slags make these materials suitable for road filling. This is further backed by their soaked and unsoaked CBR values. During the water leach tests, notable decreases in pH were observed with a 60% natural clay (NC) solution, resulting in a decrease of 1.2 and 0.7 in EAF and LS, respectively. The addition of sand had a negligible impact on pH due to its inert characteristics. Moreover, in sequential water leach tests, the most significant decrease in pH was observed with NC (with a reduction of 2.0 points for EAF and 0.9 points for LS) through enhanced ion exchange and extended periods of dilution and buffering. Also, the use of NC resulted in substantial decreases in EC for EAF and LS, with reductions of 77% and 81%, respectively. Moreover, heavy metal concentrations in leachate waters from pure steel slags have been detected, and the effect of treatment on aluminum and iron concentrations has been determined. The results indicate that the use of natural soil significantly drops the pH and lowers the trace metal concentrations within the leachate. Full article

Glass is considered a sustainable material with achievable recovery rates within the EU. However, there are limited data available for construction glass waste management. Furthermore, glass is a heavy material, and considering the geographical limitations of Cyprus, the transportation trading cost within the EU is extremely high. Therefore, another method for utilizing this by-product should be developed. The aim of this research is to investigate the production of a low-cost, lightweight and fireproof material able to retain its structural integrity, using the geopolymerization method with the incorporation of randomly collected construction glass waste. The glass waste was initially processed in a Los Angeles abrasion machine and then through a Micro-Deval apparatus in order to be converted to a fine powder. Mechanical (compressive and flexural strength), physical (setting time and water absorption) and thermal properties (thermal conductivity) were investigated. The fire-resistant materials presented densities averaging 450 kg/m³ with a range of compressive strengths of 0.5 to 3 MPa. Additionally, a techno-economic analysis was conducted to evaluate the viability of the adopted material. Based on the results, the final geopolymer product has the potential to be utilized as a fire resistance material, preventing yielding or spalling. Full article

Using limestone powder (LP), the by-product of manufactured sand, to replace part of fly ash (FA) or manufactured sand could not only turn waste into treasure and decrease the price of concrete, but could also enhance the performance of concrete and reduce environmental pollution. However, the impact of various LP incorporation methods on the performance of mass concrete was inconsistent. In this paper, the effects of LP on the workability, compressive strength, constrained expansion rate, hydration temperature and impermeability of mass concrete were studied by replacing FA or manufactured sand alone and replacing FA and manufactured sand simultaneously. The results showed that the impact of LP on the performance of mass concrete was equal when it replaced FA alone and FA and manufactured sand at the same time. When the replacement amount was 20%, the workability, expansibility and early strength of concrete were improved, but the later strength and impermeability were slightly reduced. The workability, compressive strength, expansibility and impermeability of mass concrete were improved when manufactured sand was replaced alone, and the optimal dosage was 10%. The LP, moreover, reduced the hydration temperature peak of concrete in three kinds of mixing methods, but the temperature peak appeared earlier. At lower dosages, LP optimized pore structure and promoted the early hydration of cement through filler effects and nucleation effects. When LP replaced manufactured sand, the microstructure of concrete was more dense, so the replacement of manufactured sand had a better effect on the improvement of concrete properties. A reference value for the use of LP in mass concrete is provided in this study. Full article

This work focuses on the characterization of five palygorskite clays from the Brazilian state of Piaui and their feasibility as eco-friendly adsorbents for the removal of Fe³⁺ ions from aqueous solutions. For characterization, we applied the techniques of X-ray diffraction (XRD), X-ray fluorescence (XRF), scanning electron microscopy with energy dispersive spectroscopy (SEM/EDS), size distribution measurements, density measurement by He pycnometry, superconducting quantum interference device (SQUID) magnetometry, Fourier-transform infrared spectroscopy (FTIR), thermogravimetric analysis (TGA/DTA), zeta potential measurement, hydrophobicity determination by contact angle, Brunauer–Emmett–Teller surface area analysis (BET technique) and atomic force microscopy (AFM). Batch experiments were performed in function of process parameters such as contact time and initial concentration of Fe³⁺. The natural palygorskites (Palys) had excellent performance for the removal of Fe³⁺ from aqueous solutions by adsorption (around 60 mg/g), and the Langmuir is supposedly the best model fitted the experimental data. Full article