EK Assembly Hardware

Download as pdf or txt
Download as pdf or txt
You are on page 1of 2

EK Mount Kit Assembly Hardware:

Below you will find instructions on how to install your Hybrid Racing Motor mounts into a 96-2000 Honda Civic.

Warning: Removing an engine is a timely and detailed process. It is recommend by


Hybrid Racing to locate a performance shop with the necessary tools and experience to
perform an engine swap. This guide is to be used as an outline only.

*Mount Kit may not be legal for highway use. Hybrid Racing is not responsible for any direct or indirect, actual or
incidental expense attributed to the use of any performance parts sold by Hybrid Racing LLC. Purchasers agree to all of
the terms of this agreement upon the purchase of parts. More information can be found at www.hybrid-racing.com.

A. Transmission plate
(1) 12 x 1.25 x 80mm
(1) 12 x 1.25 x 60mm
(1) 12 x 1.25 x 40mm
(1) Spacer (1.4)
(1) Spacer (1.24)
(3) Washers .5
(2) Washers .375
(1) M10 x 25mm

*Re-use your OEM 14mm bolts for the upper mount making sure to insert the
.375 washers.

*Remove the studs from the transmission and use the 80mm/60mm/40mm for
the transmission plate making sure to use the .5in washers.

*Using an 8.5mm Drill and 10x1.5mm Tap. Drill and tap the additional hole in the
upper driver side mount.

*If the driver side frame rail mount is not tightened down to 47lbf-ft you will pull
the bolt out of the sub frame rail.

B. Passenger side upper and lower


(5) 12 x 1.25 x 35mm
(5) Washers

*Remove the studs from the upper passenger side engine mount and using 2 of
the 35mm bolts attach the upper mount. Make sure to use the .5in washers.
C. Rear sub frame flat plate
(2) .25 Spacers
(3) Washers .375
(1) 14mm x 2in
(2) 14mm x 1.5in

* Make sure to insert the .375 washers.

* The 2 small spacers go stacked in the front of the mount.

D. Rear large transmission/motor plate


(3) 12 x 1.25 x 60mm
(2) .875 Spacers
(4) .5 Washers
(1) Nut

*Insert the 2 .875in spacers between the transmission and the engine mount.
Make sure to use 2 of the .5in washers

*The remaining nut, washer, and bolt go thru the upper transmission hole.

Make sure to check all bolts are not loose and check them often the first month
after installation as vibrations can loosen bolts if not properly torque down.

You have successfully completed your K series engine mount install.


If you have any questions or comments please email Info@hybrid-racing.com

Legal Disclaimer

Users assume all cost and risk associated with these or any other items purchased from the Hybrid Racing LLC
web site.

Parts sold or manufactured by Hybrid Racing LLC may not meet legal requirements for use on public roads. People
thinking about purchasing product from Hybrid Racing LLC should check with their local or state authorities for legality. It
is the user’s responsibility to know and comply with all local and federal laws and regulations. Use or installation of Hybrid
Racing LLC products may affect user insurance and/or vehicle warranty coverage. It is the user’s sole responsibility for
consequences that may occur due to having the product installed in his/her vehicle.
Hybrid Racing LLC assumes no legal responsibilities and/or liabilities, whether to user’s vehicle, engine, person(s), and/or
property(s), that result from the use of, or servicing of a vehicle of which a Hybrid Racing LLC product has been
installed/attempted to be installed, or to any other vehicle(s) and/or person(s), regardless of whether or not this product
has any involvement directly or indirectly and/or liability, and/or whether or not proper installation has been carried forth.

All engines, engine parts and electrical components are for OFF ROAD USE ONLY/RACING VEHICLES ONLY. They are
not for or to be used on public roads in the USA.
Acquisition of a Hybrid Racing LLC product will act as an acknowledgement of the legal disclaimer stated herein.

Hybrid Racing LLC reserves the right to change this disclaimer at any time without any prior consent or notification.
Should you need to contact us our details are as follows:
Hybrid Racing LLC, 3348 Drusilla Lane, Suite 2C, Baton Rouge, LA 70809

You might also like