LM6 Aluminium alloy for Diecasting Page 1 of 3

Home About Us Processes Design Quality Products Technical Contact

LM6

Aluminium Casting Alloy (AL - Si12)

Colour Code - Yellow

Chemical composition

(Blue Figures - EN 1706 AC-44100)

Copper 0.1 Max 1.5 (0.10)

Magnesium 0.10 Max 0.10
Silicon 10.0 - 13.0 10.5 - 13.5
Iron 0.6 Max 0.65 (0.65)
Manganese 0.5 Max 0.55
Nickel 0.1 Max 0.10
Zinc 0.1 Max 0.15
Lead 0.1 Max 0.10
Tin 0.05 Max 0.05
Titanium 0.2 Max 0.20 (0.15)
Aluminium Remainder

Mechanical Properties
Sand Cast Chill Cast Die Cast

0.2 % Proof Stress ( N/mm2)* 60 - 70 70 - 80 120

Tensile Stress ( N/mm2)* 160 - 190 190 - 230 280
Elongation ( % )* 5 - 10 7 - 15 2-5
Impact Resistance. Izod (Nm) 6.0 9.0 -
Brinell Hardness Number 50 - 55 55 - 60 55 - 60
Endurance Limit
51 68 -
( 5 x 107 cycles +/- N/mm2)
Modulus of Elasticity (x103 N/mm2) 71 71 71

* The values shown are typical for sand and chill cast bars produced to the requirements of BS 1490 or diecast 6mm diameter
test bars; minimum specification requirements are in heavy type.

Strength at Elevated Temperatures.

Tensile strength and hardness decrease fairly regularly with increasing temperature and become relatively poor at
temperatures of the order of 150 ºC.

Physical Properties
Coefficient of thermal Expansion. 0.0000020
(per degree Centigrade at 20 - 30 ºC.)
Thermal Conductivity. 0.24
( Cal / cm2 / cm / ºC / sec at 20 ºC)
Elecrical Conductivity 37
( % Copper Standard at 20 ºC)
Solidification Shrinkage (approx. %) 3.7

http://www.kayepresteigne.co.uk/lm6_alloy.htm 4/1/2015
LM6 Aluminium alloy for Diecasting Page 2 of 3

Specific Gravity 2.65

Freezing Range ( ºC ) approx. 565 - 575

Figure for conductivity applies to Sand castings. Values are approximate and will vary with condition.

Machinability

Alloys of this and similar compositions are rather difficult to machine. This is due firstly to their tendency to drag and
secondly to the rapid tool wear caused by the high silicon content.
Carbide-tipped tools with large rake angles and relatively low cutting speeds give comparatively good results. A
cutting lubricant and coolant should be employed.

Corrosion Resistance

LM6 exhibits excellent resistance to corrosion under both ordinary atmospheric and marine conditions. For the
severest conditions this property can be further enhanced by anodic treatment.

Anodising

LM6 can be anodised by any of the common processes. The resulting protective film ranging in colour from grey to
dark brown.

Casting Characteristics

FLUIDITY - Can be cast into thinner and more intricate sections than any of the other types of casting alloys.
PRESSURE TIGHTNESS - Especially suitable for teak-tight castings.
HOT-TEARING - Castings in sand or chill moulds exhibit complete freedom from hot-tearing.
TYPICAL POURING TEMPERATURE - A typical temperature for sand and chill castings is 725 ºC but in practice it
may range considerably above or below this value according to the dimensions of the casting.

Pouring temperatures for diecastings depend very largely on the particular casting and the machine and vary too
widely for a typical temperature to provide useful guidance~ The melt should not, however, be allowed to stand at
temperatures only a little above the freezing range or the bottom of the melt may become enriched in such
elements as iron and manganese

PATTERNMAKERS' SHRINKAGE - 1.3% or 1/75 NB For diecastings the shrinkage may be expected to be
considerably less.

NOTES -for sand castings and medium and heavy section chill castings the alloy must be modified before pouring
(by treatment with sodium or sodium salts ~ see booklet 'Melting Practice for the Production of Aluminium Alloy
castings'), if the maximum mechanical properties are to be realised. An alternative modifying process is the
treatment of the melt with strontium as an aluminium-silicon-strontium hardener- A more persistent state of
modification is achieved by this method.

Heat Treatment

Ductility can be improved slightly by heating at 250-300 ºC but apart from stress relieving, the heat-treatment of
LM6 is of little industrial interest.

Applications and General Notes

Suitable for marine 'on deck' castings. water-cooled manifolds and jackets, motor-car and road transport fittings;
thin sections and intricate castings such as motor housings, meter cases and switch-boxes; for very large castings,
e.g., cast doors and panels where ease of casting is essential; for chemical and dye industry castings, e.g. pump
parts: for paint industry and-food and domestic castings. In general use where marine atmospheres or service
conditions make corrosion resistance a matter of major importance. Especially suitable for castings that are to be
welded. The ductility of LM6 alloy enables castings easily to be rectified or even modified in shape, e.g., simple

http://www.kayepresteigne.co.uk/lm6_alloy.htm 4/1/2015
LM6 Aluminium alloy for Diecasting Page 3 of 3

components maybe cast straight and later bent to the required contour-Equally adaptable for sand and permanent
mould castings and for diecastings

The aluminium-silicon alloys possess exceptional casting characteristics, which enable them to be used to produce
intricate castings of thick and thin sections. Fluidity and freedom from hot-tearing increase with silicon content and
are excellent throughout the range Their resistance to corrosion is very good, but special care is required in
machining. In general, the binary alloys are not heat-treated: at elevated temperatures their strength falls rapidly.
Although of medium strength their hardness and elastic limit are low but they possess excellent ductility.

Back to the top

Back to Home Page

Html navigation Terms and conditions Privacy policy Harper Street, Presteigne, Powys LD8 2AL United Kingdom
© 2009 Kaye Engineering Limited

http://www.kayepresteigne.co.uk/lm6_alloy.htm 4/1/2015