Scribd Logo
Upload

Welcome to Scribd!

  • 152 views

    Cisco Router Configuration Commands

    Uploaded by

    Teny Varghese
    This document provides an overview of basic Cisco router configuration commands organized into the following sections: requirement and corresponding Cisco command, show commands, basic operations, copy commands, and debug commands. The configuration commands cover topics like setting passwords, enabling interfaces, IP addressing, routing protocols, static routes, and disabling CDP. The show commands display router information and status. The copy commands are used to save and transfer configurations. Debug commands turn on debugging for specific protocols.

    Copyright:

    Attribution Non-Commercial (BY-NC)
    Download as DOCX, PDF, TXT or read online from Scribd

    Cisco Router Configuration Commands

    Uploaded by

    Teny Varghese
    152 views4 pages
    This document provides an overview of basic Cisco router configuration commands organized into the following sections: requirement and corresponding Cisco command, show commands, basic operations, copy commands, and debug commands. The configuration commands cover topics like setting passwords, enabling interfaces, IP addressing, routing protocols, static routes, and disabling CDP. The show commands display router information and status. The copy commands are used to save and transfer configurations. Debug commands turn on debugging for specific protocols.

    Copyright

    © Attribution Non-Commercial (BY-NC)

    Available Formats

    DOCX, PDF, TXT or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    This document provides an overview of basic Cisco router configuration commands organized into the following sections: requirement and corresponding Cisco command, show commands, basic operations, copy commands, and debug commands. The configuration commands cover topics like setting passwords, enabling interfaces, IP addressing, routing protocols, static routes, and disabling CDP. The show commands display router information and status. The copy commands are used to save and transfer configurations. Debug commands turn on debugging for specific protocols.

    Copyright:

    Attribution Non-Commercial (BY-NC)
    Download as DOCX, PDF, TXT or read online from Scribd
    Download as docx, pdf, or txt
    152 views4 pages

    Cisco Router Configuration Commands

    Uploaded by

    Teny Varghese
    This document provides an overview of basic Cisco router configuration commands organized into the following sections: requirement and corresponding Cisco command, show commands, basic operations, copy commands, and debug commands. The configuration commands cover topics like setting passwords, enabling interfaces, IP addressing, routing protocols, static routes, and disabling CDP. The show commands display router information and status. The copy commands are used to save and transfer configurations. Debug commands turn on debugging for specific protocols.

    Copyright:

    Attribution Non-Commercial (BY-NC)
    Download as DOCX, PDF, TXT or read online from Scribd
    Download as docx, pdf, or txt
    of 4

    Cisco Router Configuration Commands

    More Cisco information: - Cisco Router Commands


    - Cisco IP Addressing Commands
    - Cisco IP Services Commands
    - Cisco Router and Switch Commands
    - Cisco Router Configuration Commands
    - LAB 1 Basic Cisco configuration commands
    Other information: - IP6 Next Generation Overview
    - Linux Commands
    - Tom's MCSE Notes
    - Tom's A+ Plus Notes
    - Tom's Networking+ (Net+) Plus Notes

    Requirement Cisco Command

    Set a console password to cisco Router(config)#line con 0


    Router(config-line)#login
    Router(config-line)#password cisco

    Set a telnet password Router(config)#line vty 0 4


    Router(config-line)#login
    Router(config-line)#password cisco

    Stop console timing out Router(config)#line con 0


    Router(config-line)#exec-timeout 0 0

    Set the enable password to cisco Router(config)#enable password cisco

    Set the enable secret password to peter. Router(config)#enable secret peter

    This password overrides the enable password 


    and is encypted within the config file

    Enable an interface Router(config-if)#no shutdown

    To disable an interface Router(config-if)#shutdown

    Set the clock rate for a router with a DCE cable to 64K Router(config-if)clock rate 64000

    Set a logical bandwidth assignment of 64K to the serial interface Router(config-if)bandwidth 64


    Note that the zeroes are not missing

    To add an IP address to a interface Router(config-if)#ip addr 10.1.1.1


    255.255.255.0
    To enable RIP on all 172.16.x.y interfaces Router(config)#router rip
    Router(config-router)#network 172.16.0

    Disable RIP Router(config)#no router rip

    To enable IRGP with a AS of 200, to all interfaces Router(config)#router igrp 200


    Router(config-router)#network 172.16.0

    Disable IGRP Router(config)#no router igrp 200

    Static route the remote network is 172.16.1.0, with a mask of 255.255.255.0, Router(config)#ip route 172.16.1.0
    the next hop is 172.16.2.1, at a cost of 5 hops 255.255.255.0 172.16.2.1 5

    Disable CDP for the whole router Router(config)#no cdp run

    Enable CDP for he whole router Router(config)#cdp run

    Disable CDP on an interface Router(config-if)#no cdp enable

    Cisco Router Show Commands

    Requirement Cisco Command

    View version information show version

    View current configuration (DRAM) show running-config

    View startup configuration (NVRAM) show startup-config

    Show IOS file and flash space show flash

    Shows all logs that the router has in its memory show log

    View the interface status of interface e0 show interface e0

    Overview all interfaces on the router show ip interfaces brief

    View type of serial cable on s0 show controllers 0 (note the space between the 's' and
    '0')

    Display a summary of connected cdp devices show cdp neighbor

    Display detailed information on all devices show cdp entry *

    Display current routing protocols show ip protocols


    Display IP routing table show ip route

    Display access lists, this includes the number of displayed show access-lists
    matches

    Check the router can see the ISDN switch show isdn status

    Check a Frame Relay PVC connections show frame-relay pvc

    show lmi traffic stats show frame-relay lmi

    Display the frame inverse ARP table show frame-relay map

    Cisco Router Basic Operations

    Requirement Cisco Command

    Enable Enter privileged mode

    Return to user mode from privileged disable

    Exit Router Logout or exit or quit

    Recall last command up arrow or <Ctrl-P>

    Recall next command down arrow or <Ctrl-N>

    Suspend or abort <Shift> and  <Ctrl> and 6 then x

    Refresh screen output <Ctrl-R>

    Compleat Command TAB

    Cisco Router Copy Commands

    Requirement Cisco Command

    Save the current configuration from DRAM to copy running-config startup-config


    NVRAM

    Merge NVRAM configuration to DRAM copy startup-config running-config

    Copy DRAM configuration to a TFTP server copy runing-config tftp

    Merge TFTP configuration with current router copy tftp runing-config


    configuration held in DRAM

    Backup the IOS onto a TFTP server copy flash tftp

    Upgrade the router IOS from a TFTP server copy tftp flash

    Cisco Router Debug Commands

    Requirement Cisco Command

    Enable debug for RIP debug ip rip

    Enable summary IGRP debug information debug ip igrp events

    Enable detailed IGRP debug information debug ip igrp transactions

    Debug IPX RIP debug ipx routing activity

    Debug IPX SAP debug IPX SAP

    Enable debug for CHAP or PAP debug ppp authentication

    Switch all debugging off no debug all 


    undebug all

    You might also like