Installing and Configuring the Cisco Secure

Access Control System with

CSACS-1121
This chapter describes how to install and initially configure CSACS-1121 and the ACS 5.8.1 server.

Installation Using the CSACS-1121 Series Appliance, page 1

Downloading the Cisco Secure ACS 5.8.1 ISO Image, page 2

Installing the ACS Server, page 2

Resetting the Administrator Password, page 6

Reimaging the ACS Server, page 6

Installation Using the CSACS-1121 Series Appliance

The CSACS-1121 appliance is preinstalled with the ACS 5.8.1 software. This section gives you an overview of the
installation process and the tasks that you must perform before installing ACS.

Before you begin installing ACS 5.8.1, you must:

1. Open the box and check the contents. See Unpacking and Checking the Contents of Your Shipment, page 9

2. Read Introducing the Cisco 1121 Secure Access Control System Hardware, page 1

3. Read the general precautions and safety warnings in Preparing to Install the Cisco 1121 Secure Access Control
System Hardware, page 1

4. Install the appliance in the rack. See Installing the Cisco 1121 Secure Access Control System Hardware, page 1

5. Connect the CSACS-1121 to the network and appliance console. See Connecting Cables, page 7

6. Power up the CSACS-1121 appliance. See Powering Up the CSACS-1121 Series Appliance, page 17

7. Run the setup command at the CLI prompt to configure the initial settings for the ACS server. See Running the Setup
Program, page 2.

Downloading the Cisco Secure ACS 5.8.1 ISO Image

You can download the Cisco Secure ACS 5.8.1 ISO image from Cisco.com

1. Go to http://www.cisco.com/go/acs. You must already have a valid Cisco.com login credentials to access this link.

2. Click Download Software.

Cisco Systems, Inc. www.cisco.com

1
Installing and Configuring the Cisco Secure Access Control System with CSACS-1121

Installing the ACS Server

The Cisco Secure ACS Release 5.8.1 software image appears on the Cisco.com page. You can test all the Cisco ACS
services once your installation and initial configuration are complete.

Note: You can download the ACS 5.x software images from Cisco.com only when you have a valid Software Application
Support (SAS) contract for a previous version of ACS 5.x software. If you do not have a valid SAS contract for a previous
version, you must contact your Sales Engineer (SE), Accounts Manager (AM), or Cisco partners to publish the software
image on Cisco.com to the specific customers account.

Installing the ACS Server

This section describes how to install ACS on the CSACS-1121 Series appliance.

This section contains:

Running the Setup Program, page 2

Verifying the Installation Process, page 5

Running the Setup Program

This section describes the setup process to install the ACS server.

The setup program launches an interactive command-line interface (CLI) that prompts you for the required parameters.

An administrator can use the console or a dumb terminal to configure the initial network settings and provide the initial
administrator credentials for the ACS 5.8.1 server using the setup program. The setup process is a one-time
configuration task.

To install the ACS server:

1. Power on the appliance.

The setup prompt appears:

Please type setup to configure the appliance

localhost login:

2. At the login prompt, enter setup and press Enter.

The console displays a set of parameters. You must enter the parameters as described in Table 1 on page 3.

Note: You can interrupt the setup process at any time by typing Ctrl-C before the last setup value is entered.

2
Installing and Configuring the Cisco Secure Access Control System with CSACS-1121

Installing the ACS Server

Table 1 Network Configuration Parameters

Prompt Default Conditions Description
Host Name localhost First letter must be an ASCII character. Enter the hostname.

Length must be from 3 to 15 characters.

Valid characters are alphanumeric (A-Z,

a-z, 0-9), hyphen (-), and the first
character must be a letter.

Note: When you intend to use AD ID store

and set up multiple ACS instances with
same name prefix, use maximum of 15
characters as the host name so that it
does not affect the AD functionality.
IPV4 IP Address None, network specific Must be a valid IPv4 address between Enter the IP address.
0.0.0.0 and 255.255.255.255.
IPv4 Netmask None, network specific Must be a valid IPv4 address between Enter a valid netmask.
0.0.0.0 and 255.255.255.255.
IPv4 Gateway None, network specific Must be a valid IPv4 address between Enter a valid default gateway.
0.0.0.0 and 255.255.255.255.
Domain Name None, network specific Cannot be an IP address. Enter the domain name.

Valid characters are ASCII characters, any

numbers, hyphen (-), and period (.).
IPv4 Primary Name None, network specific Must be a valid IPv4 address between Enter a valid name
Server Address 0.0.0.0 and 255.255.255.255. server address.
Add another None, network specific Must be a valid IPv4 address between To configure multiple name
nameserver 0.0.0.0 and 255.255.255.255. servers, enter Y.

Note: You can configure a maximum of

three name servers from ACS CLI.
NTP Server time.nist.gov Must be a valid IPv4 address between Enter a valid domain name
0.0.0.0 and 255.255.255.255 or a domain server or an IPv4 address.
name server.

Note: You can configure a maximum of

three NTP servers from ACS CLI.
Timezone UTC Must be a valid local time zone. Enter a valid timezone.

3
Installing and Configuring the Cisco Secure Access Control System with CSACS-1121

Installing the ACS Server

Table 1 Network Configuration Parameters (continued)

Prompt Default Conditions Description
SSH Service None, network specific None To enable SSH service,
enter Y.
Username admin The name of the first administrative user. Enter the username.
You can accept the default or enter a new
username.

Must be from 3 to 8 characters, and must

be alphanumeric (A-Z, a-z, 0-9).
Admin Password None No default password. Enter your Enter the password.
password.

The password must be at least six

characters in length, have at least one
lowercase letter, one uppercase letter,
and one number.

In addition:

Save the user and password

information for the account that you
set up for initial configuration.

Remember and protect these

credentials because they allow
complete administrative control of
the ACS hardware, the CLI, and the
application.

If you lose your administrative

credentials, you can reset your
password by using the ACS 5.8.1
Installation and Recovery DVD.

The console requests for the parameters as shown below:

localhost login: setup

Enter hostname[]: acs-server-1
Enter IP address[]: a.b.c.d
Enter IP default netmask[]: 255.255.255.255
Enter IP default gateway[]: a.b.c.d
Enter default DNS domain[]: mycompany.com
Enter primary nameserver[]: a.b.c.d
Add secondary nameserver? Y/N : n
Add primary NTP server [time.nist.gov]: a.b.c.d
Add secondary NTP server? Y/N : n
Enter system timezone[UTC]:
Enable SSH service? Y/N [N] : y
Enter username [admin]: admin
Enter password:
Enter password again:
Pinging the gateway...
Pinging the primary nameserver...
Do not use `Ctrl-C' from this point on...
Appliance is configured
Installing applications...
Installing acs...
Generating configuration...

4
Installing and Configuring the Cisco Secure Access Control System with CSACS-1121

Installing the ACS Server

Rebooting...

After the ACS server is installed, the system reboots automatically.

Now, you can log into ACS using the CLI username and password that was configured during the setup process.

Note: You can use this username and password to log into ACS only via the CLI.

Note: The initial setup of the ACS 5.8.1 server should be configured with an IPv4 address. You can configure the IPv6 IP
address for your server only after the initial setup is completed.

Note: ACS 5.8.1 supports IPv4 and IPv6 dual stack networking and does not support pure IPv6 network.

Verifying the Installation Process

To verify that you have correctly completed the installation process:

1. When the system reboots, at the login prompt enter the username you configured during setup, and press Enter.

2. At password prompt, enter the password you configured during setup, and press Enter.

3. Verify that the application has been installed properly by entering show application, and press Enter.

The console displays:

<name> <Description>
acs Cisco Secure Access Control System 5.8.1

4. At the system prompt, check the release and ACS version that are installed, at the system prompt by entering show
application version acs and pressing Enter.

The console displays:

Cisco ACS VERSION INFORMATION

-----------------------------

Version: 5.8.1.4
Internal Build ID: B.462

Note: The Version and Internal Build ID may change for different versions of this release.

5. Check the status of ACS processes, at the system prompt by entering show application status acs, and press
Enter.

The console displays:

ACS role: PRIMARY

Process 'database' running
Process 'management' running
Process 'runtime' running
Process 'adclient' running
Process 'ntpd' running
Process 'view-database' running
Process 'view-jobmanager' running
Process 'view-alertmanager' running
Process 'view-collector' running
Process 'view-logprocessor' running

Note: To get the latest ACS patches and to keep your ACS up-to-date, visit
http://software.cisco.com/download/navigator.html?i=rt

5
Installing and Configuring the Cisco Secure Access Control System with CSACS-1121

Resetting the Administrator Password

Resetting the Administrator Password

If you are not able to log in to the system due to the loss of the administrator password, you can use the ACS 5.8.1
recovery DVD to reset the administrator password.

To reset the administrator password:

1. Power up the appliance.

2. Insert the ACS 5.8.1 recovery DVD.

The console displays:

Welcome to Cisco Secure ACS 5.8.1 Recovery

To boot from hard disk press <Enter>
Available boot options:
[1] Cisco Secure ACS 5.8.1 Installation (Keyboard/Monitor)
[2] Cisco Secure ACS 5.8.1 Installation (Serial Console)
[3] Reset Administrator Password (Keyboard/Monitor)
[4] Reset Administrator Password (Serial Console)
<Enter> Boot from hard disk
Please enter boot option and press <Enter>.
boot:

To reset the administrator password, at the system prompt, enter 3 if you are using a keyboard and video monitor,
or enter 4 if you are using a serial console port.

The console displays a set of parameters.

3. Enter the parameters as described in Table 2 on page 6.

Table 2 Password Reset Parameters

Parameter Description
Admin username Enter the number of the administrator whose password you want
to reset.
Password Enter the new password for the administrator.
Verify password Enter the password again.
Save change & Reboot Enter Y to save.

The console displays:

Admin username:
[1]:admin
[2]:admin2
[3]:admin3
Enter number of admin for password recovery:1
Password:
Verify password:
Save change&reeboot? [Y/N]:

Reimaging the ACS Server

To reimage the ACS server:

1. Power up the appliance.

2. Insert the ACS Recovery DVD.

6
Installing and Configuring the Cisco Secure Access Control System with CSACS-1121

Regulatory Compliance

The console displays:

Welcome to Cisco Secure ACS 5.8.1 Recovery

To boot from hard disk press <Enter>
Available boot options:
[1] Cisco Secure ACS 5.8.1 Installation (Keyboard/Monitor)
[2] Cisco Secure ACS 5.8.1 Installation (Serial Console)
[3] Reset Administrator Password (Keyboard/Monitor)
[4] Reset Administrator Password (Serial Console)
<Enter> Boot from hard disk
Please enter boot option and press <Enter>.
boot:

3. At the console prompt, enter 1 if you are using a keyboard and video monitor, or enter 2 if you are using a serial
console port, and press Enter.

The reimage process uninstalls the existing ADE-OS and ACS versions, and installs the latest versions. For the
installation process, see the section Running the Setup Program, page 2.

Regulatory Compliance
For regulatory compliance and safety information, see Regulatory Compliance and Safety Information for Cisco Secure
Access Control System.

7
Installing and Configuring the Cisco Secure Access Control System with CSACS-1121

Regulatory Compliance