Search Results (1,988)

Thin sound-absorbing materials are particularly desired in space-constrained applications, such as in the automotive industry. In this study, we theoretically analyzed the structure of relatively thin glass wool or polyester wool laminated with a nonpermeable polyethylene membrane and a permeable nonwoven fabric sheet. We also measured and compared the sound-absorption coefficients of these samples between experimental and theoretical values. The sound-absorption coefficient was derived using the transfer matrix method. The Rayleigh model was applied to describe the acoustic behavior of glass wool and nonwoven sheet, while the Miki model was used for polyester wool. Mathematical formulas were employed to model an air layer without damping and a vibrating membrane. These acoustic components were integrated into a transfer matrix framework to calculate the sound-absorption coefficient. The sound-absorption coefficients of glass wool and polyester wool were progressively enhanced by sequentially adding suitable nonwoven fabric and PE membranes. A sample approximately 10 mm thick, featuring permeable and nonpermeable membranes as outer layers of porous sound-absorbing material, achieved a sound-absorption coefficient equivalent to that of a sample occupying 20 mm thickness (10 mm of porous sound-absorbing material with a 10 mm back air layer). Full article

Polyurethanes (PUs) synthesized with blends of polycarbonate and polyester polyols (CD+PEs) showed intrinsic self-healing at 20 °C. The decrease in the polycarbonate soft segments content increased the self-healing time and reduced the kinetics of self-healing of the PUs. The percentage of C-O species decreased and the ones of C-N and C=O species increased by increasing the polyester soft segments in the PUs, due to higher micro-phase separation. All PUs synthetized with CD+PE blends exhibited free carbonate species and interactions between the polycarbonate and polyester soft segments to a somewhat similar extent in all PUs. By increasing the polyester soft segments content, the storage moduli of the PUs decreased and the tan delta values increased, which resulted in favored polycarbonate soft segments interactions, and this was related to slower kinetics of self-healing at 20 °C. Although the PU made with a mixture of 20 wt.% CD and 80 wt.% PE showed cold crystallization and important crystallinity of the soft segments, as well as high storage moduli, the intercalation of a small amount of polycarbonate soft segments disturbed the interactions between the polyester soft segments, so it exhibited self-healing at 20 °C. The self-healing of the PUs was attributed to the physical interactions between polycarbonate soft segments themselves and with polyester soft segments, and, to a minor extent, to the mobility of the polymeric chains. Finally, the PUs made with 40 wt.% or more polyester polyol showed acceptable mechanical properties. Full article

In this work, a flexible textile-based capacitive respiratory sensor, based on a capacitive sensor structure, that does not require direct skin contact is designed, optimised, and evaluated using both computational modelling and empirical measurements. In the computational study, the geometry of the sensor was examined. This analysis involved observing the capacitance and frequency variations using a cylindrical model that mimicked the human body. Four designs were selected which were then manufactured by screen printing multiple functional layers on top of a polyester/cotton fabric. The printed sensors were characterised to detect the performance against phantoms and impacts from artefacts, normally present whilst wearing the device. A sensor that has an electrode ratio of 1:3:1 (sensor, reflector, and ground) was shown to be the most sensitive design, as it exhibits the highest sensitivity of 6.2% frequency change when exposed to phantoms. To ensure the replicability of the sensors, several batches of identical sensors were developed and tested using the same physical parameters, which resulted in the same percentage frequency change. The sensor was further tested on volunteers, showing that the sensor measures respiration with 98.68% accuracy compared to manual breath counting. Full article

Recently, plaster has gained increasing attention as a mechanical and environmentally friendly option and is an effective alternative to traditional cement products. Additionally, polyester has an effective impact on the mechanical properties of materials, in addition to being one of the most environmentally friendly materials. However, studies are still ongoing to reach the best ratios of polyester resin, polyester hardener, and gypsum plaster that can improve mechanical properties. This research aims to investigate the impact of these components at various ratios (30%, 45%, and 60%) of gypsum plaster weight on the mechanical properties of plaster material. This study is carried out by conducting compression and tensile tests for three ratios, which are considered among the most important mechanical tests according to their applications. In addition, the environmental emissions resulting from the three different ratios of plaster are evaluated to determine their environmental impact. This study found that the largest ratio (30%) was the most effective from an economic and mechanical point of view, while achieving lower carbon emissions compared to the other ratios, which enhances the trend towards achieving the environmental goals of the Kingdom of Saudi Arabia’s Vision 2030 to reach zero emissions. This study is highly significant both in terms of scientific research and practical application across a range of industries, since it integrates the enhancement of material performance with the achievement of environmental sustainability requirements. Full article

Cotton and polyester fiber blends are commonly used to improve the aesthetic features of finished items. The denim industry’s growing need for polyester fiber aids in analyzing the performance of denim fabrics woven from rigid and stretched weft yarn combined with cotton and polyester. This study evaluates the weight, dimensional changes, stiffness, tensile and tearing strength, stretch, and comfort properties of denim fabric woven from cotton and polyester in various blended ratios. Here, Ne 14/1 (42 tex) 100% cotton warp yarn and Ne 18/1 (33 tex) weft yarns, consisting of 100% cotton, 75/25, 50/50, and 25/75 cotton/polyester (CO/PES) blends, as well as 100% polyester, were used to produce 3/1 Z twill denim fabric. The weft yarns were categorized into three groups: rigid, core-spun, and dual-core-spun yarns. Experimental results showed a higher polyester content in weft yarn, and denim fabrics’ tensile and tearing strength was improved, whereas fabrics’ weight loss, dimensional changes, and stretch properties were reduced. Furthermore, different statistical analyses were conducted to evaluate the type of weft yarn and blending ratio interaction and correlation with fabric properties. Additionally, a regression model was developed with the weft yarn type and blending ratio as independent variables to predict the fabric properties. Full article

The search for alternatives to petrochemical plastics has intensified, with increasing attention being directed toward bio-based polymers (bioplastics), which are considered healthier and more environmentally friendly options. In this review, a comprehensive overview of polyhydroxyalkanoates (PHAs) is provided, including their characterization, applications, and the mechanisms underlying their biosynthesis. PHAs are natural polyesters produced by a wide range of prokaryotic and some eukaryotic organisms, positioning them as a significant and widely studied type of bioplastic. Various strategies for the production of PHAs from agroindustrial waste, such as cacao shells, cheese whey, wine, wood, and beet molasses, are reviewed, emphasizing their potential as sustainable feedstocks. Industrial production processes for PHAs, including the complexities associated with extraction and purification, are also examined. Although the use of waste materials offers promise in reducing costs and environmental impact, challenges remain in optimizing these processes to enhance efficiency and cost-effectiveness. The need for continued research and development to improve the sustainability and economic viability of PHA production is emphasized, positioning PHAs as a viable and eco-friendly alternative to conventional petroleum-based plastics. Full article

Composite polymer membranes were obtained using the so-called dry phase inversion and were used for desalination of diluted saline water solutions by pervaporation (PV) method. The tests used a two-layer backing, porous, ultrafiltration commercial membrane (PS20), which consisted of a supporting polyester layer and an active polysulfone layer. The active layer of PV membranes was obtained in an aqueous environment, in the presence of a surfactant, by cross-linking a 5 wt.% aqueous solution of polyvinyl alcohol (PVA)—using various amounts of cross-linking substances: 50 wt.% aqueous solutions of glutaraldehyde (GA) or citric acid (CA) or a 40 wt.% aqueous solution of glyoxal. An ethylene glycol oligomer (PEG 200) was also used to prepare active layers on PV membranes. Witch its help a chemically cross-linked hydrogel with PVA and cross-linking reagents (CA or GA) was formed and used as an active layer. The manufactured PV membranes (PVA/PSf/PES) were used in the desalination of water with a salinity of 35‰, which corresponds to the average salinity of oceans. The pervaporation method was used to examine the efficiency (productivity and selectivity) of the desalination process. The PV was carried at a temperature of 60 °C and a feed flow rate of 60 dm³/h while the membrane area was 0.005 m². The following characteristic parameters of the membranes were determined: thickness, hydrophilicity (based on contact angle measurements), density, degree of swelling and cross-linking density and compared with the analogous properties of the initial PS20 backing membrane. The physical microstructure of the cross-section of the membranes was analyzed using scanning electron microscopy (SEM) method. Full article

This study explores the intricate interaction between the properties of textile substrates and screen-printing parameters in shaping fabric circuits using silver conductive ink. Via analyzing key variables such as fabric type, mesh density, and the number of overprinted layers, the research revealed how the porous structure, large surface area, and fiber morphology of textile substrates influence ink absorption, ultimately enhancing the electrical connectivity of the printed circuits. Notably, the hydrophilic cotton staple fibers fabric effectively absorbed the conductive ink into the fabric substrate, demonstrating superior electrical performance compared with the hydrophobic polyester filament fabric after three overprinting, unlike the results observed after a single print. As mesh density decreased and the number of prints increased, the electrical resistance of the circuit gradually reduced, but ink bleeding on the fabric surface became more pronounced. Cotton fabric, via absorbing the ink deeply, exhibited less surface bleeding, while polyester fabric showed more noticeable ink spreading. These findings provide valuable insights for improving screen printing technology for textile circuits and contribute to the development of advanced fabric circuits that enhance the functionality of smart wearable technology. Full article

Furanoate polyesters are an extremely promising new class of materials for packaging applications, particularly furanoate-based nanocomposites, which have gained a high interest level in research and development in both academia and industries. The monomers utilised for the synthesis of furanoate-based polyesters were derived from lignocellulosic biomass, which is essential for both eco-friendliness and sustainability. Also, these polyesters have a lower carbon footprint compared to fossil-based plastics, contributing to greenhouse gas reduction. The furanoate-based nanocomposites exhibit enhanced performance characteristics, such as high thermal stability, excellent mechanical strength, superior barrier resistance, and good bacteriostatic rate, making them suitable for a wide range of industrial applications, especially for food-packaging applications. This paper reviews the recent trends in the synthesis routes of monomers, such as the various catalytic activities involved in the oxidation of 5(hydroxymethyl)furfural (HMF) into 2,5-furandicarboxylic acid (FDCA) and its ester, dimethyl furan-2,5-dicarboxylate (DMFD). In addition, this review explores the fabrication of different furanoate-based nanocomposites prepared by in situ polymerization, by melt mixing or solvent evaporation methods, and by using different types of nanoparticles to enhance the overall material properties of the resulting nanocomposites. Emphasis was given to presenting the effect of these nanoparticles on the furanoate polyester’s properties. Full article

The aim of this project was to assess the thermal conductivity of polyethylene (PE) filled with carbon black (CB), specifically for geothermal pipes. The project explored the potential modification of PE’s thermal conductivity by incorporating recycled textile fibers. Different types of shredded recycled fibers were tested, including two types of polyamide fibers with varying contaminations and one type of polyester fiber. Following several preparation steps, various composite materials were manufactured and compared to bulk PE using various testing methods: Differential Scanning Calorimetry analysis (DSC), mechanical testing (flexural and tensile), and laser flash analysis (LFA). The results revealed alterations in the mechanical properties of the composite materials in comparison to PE filled with CB. The LFA tests demonstrated the effectiveness in reducing polymer thermal diffusivity at higher temperatures, particularly when the material was loaded with recycled polyester fillers. Full article

This research investigates the manufacturing and characterisation of polyester-based composites reinforced with jute fibres and red mud particulates. The motivation stems from the need for sustainable, high-performance materials for applications in industries, like aerospace and automotive, where resistance to erosion is critical. Jute, a renewable fibre, combined with red mud, an industrial byproduct, offers an eco-friendly alternative to conventional composites. The composites were fabricated using compression moulding with varying red mud contents (10, 20, and 30 wt.%) and a fixed 40 wt.% of jute fibre. Fibre treatments included sodium hydroxide (NaOH) and silane treatments to improve bonding and performance. Erosion tests were performed using an air-jet erosion tester, examining the effects of the red mud content, fibre treatment, and impact angles. Scanning Electron Microscope (SEM) analysis provided insights into the erosion mechanisms. A distinctive reduction in erosion rates at higher impact angles (30°–60°) was observed, attributed to the semi-ductile nature of the composites. The addition of red mud enhanced erosion resistance, although an excess of 30 wt.% reduced resistance due to poor surface bonding. Silane-treated composites showed the lowest erosion rates. This study provides new insights into the interplay among material composition, fibre treatment, and erosion dynamics, contributing to the development of optimised, eco-friendly composite materials. Full article

Controlling the cooling rate experienced by a material during a manufacturing process is a challenge and a major issue. Industrial processing techniques are very diverse and may involve a whole range of cooling rates, which are sometimes extremely high for small and/or thin manufactured parts. For polymers, the cooling rate has consequences on both the microstructure and the time-dependent properties. The common cooling rates associated with conventional calorimetric measurements are generally limited to a few tens of degrees per minute. This work combines several calorimetric techniques (DSC, modulated-temperature DSC, stochastically-modulated DSC and Fast Scanning Calorimetry) to estimate the critical cooling rate required to melt-quench fast-crystallizing polyesters to their fully amorphous state, based on the example of a series of poly(alkylene trans-1,4-cyclohexanedicarboxylate) (PCHs) with a number of methylene groups in the main structure of the repeating unit $n_{C{H}_2}$ varying from 3 to 6. The even-numbered ones require faster cooling rates (about 3000 K s⁻¹ for $n_{C{H}_2}$ = 4, between 500 and 1000 K s⁻¹ for $n_{C{H}_2}$ = 6) compared to the odd-numbered ones (between 50 K min⁻¹ and 100 K s⁻¹ for $n_{C{H}_2}$ = 3, between 10 and 30 K min⁻¹ for $n_{C{H}_2}$ = 5). Full article

Extrusion processing of plasticized cassava starch, a prominent industrial crop, with chemical additives offers a thermo-mechanical approach to modify starch structures through physical and chemical interactions. This research investigates the interaction and morphology of thermoplastic cassava starch (TPS) blended with tetrasodium pyrophosphate (Na₄P₂O₇), sodium tripolyphosphate (Na₅P₃O₁₀), sodium hexametaphosphate (Na₆(PO₃)₆), sodium erythorbate (C₆H₇O₆Na), and sodium nitrite (NaNO₂) via twin-screw extrusion. The effects of these additives on the chemical structure, thermal profile, water absorption, and solubility of the TPS were examined. The high temperature and shearing forces within the extruder disrupted hydrogen bonding at α-(1-4) and α-(1-6) glycosidic linkages within anhydroglucose units. Na₄P₂O₇, Na₅P₃O₁₀ and Na₆(PO₃)₆ induced starch phosphorylation, while ¹H NMR and ATR-FTIR analyses revealed that C₆H₇O₆Na and NaNO₂ caused starch hydrolysis. These additives hindered starch recrystallization, resulting in higher amorphous fractions that subsequently influenced the thermal properties and stability of the extruded TPS. Furthermore, the type and content of the added modifier influenced the water absorption and solubility of the TPS due to varying levels of interaction. These modified starch materials exhibited enhanced antimicrobial properties against Escherichia coli and Staphylococcus aureus in polyester blends fabricated via extrusion, with nitrite demonstrating the most potent antimicrobial efficacy. These findings suggest that starch modification via either phosphorylation or acid hydrolysis impacts the thermal properties, morphology, and hydrophilicity of extruded cassava TPS. Full article

Polyesters (PEs) are sustainable alternatives for conventional polymers owing to their potential degradability, recyclability, and the wide availability of bio-based monomers for their synthesis. Herein, we used a one-pot, one-step self-switchable polymerization linking the ring-opening alternating copolymerization (ROAC) of epoxides/cyclic anhydrides with the ring-opening polymerization (ROP) of L-lactide (LLA) to synthesize PE-based hot-melt adhesives with a high bio-based content. In the cesium pivalate-catalyzed self-switchable polymerization of glutaric anhydride (GA), butylene oxide (BO), and LLA using a diol initiator, the ROAC of GA and BO proceeded whereas the ROP of LLA simultaneously proceeded very slowly, resulting in a copolyester consisting of poly(GA-alt-BO) and poly(L-lactide) (PLLA) segments with tapered regions, that is, PLLA-tapered block-poly(GA-alt-BO)-tapered block-PLLA (PLLA-tb-poly(GA-alt-BO)-tb-PLLA). Additionally, a series of tapered-block or real-block copolyesters consisting of poly(anhydride-alt-epoxide) (A segment) and PLLA (B segment) with AB-, BAB-, (AB)₃-, and (AB)₄-type architectures of different compositions and molecular weights were synthesized by varying the monomer combinations, alcohol initiators, and initial feed ratios. The lap shear tests of these copolyesters revealed an excellent relationship between the adhesive strength and polymer structural parameters. The (AB)₄-type star-block copolyester (poly(GA-alt-BO)-tb-PLLA)₄ exhibited the best adhesive strength (6.74 ± 0.64 MPa), comparable to that of commercial products, such as PE-based and poly(vinyl acetate)-based hot-melt adhesives. Full article

Plastic is a growing global environmental problem. While much of the focus of anthropogenic microparticles has focused on microplastics and their occurrence in marine systems, anthropogenic microparticles are found in freshwater systems. The Charles River is a highly impacted and historically important river within Massachusetts and runs for 80 miles within the state of MA through a variety of land uses. Microparticle concentrations were found to vary along the length of the river and ranged in concentrations from 1–19 pieces/L, with generally higher concentrations downstream. Microfibers were the dominant (72%) type of microparticles found, and the majority (avg 76%) of microparticles were synthetic. The highest estimated flux of microparticles occurred in May, with an estimated flux of 2 billion microparticles per day via the Charles River into the Boston Harbor. The average annual concentration of microparticles was correlated with land use, with higher concentrations occurring in regions with higher impervious coverage and in areas designated as industrial or high-density residential. Polyester, polypropylene, and polyamides were the dominant plastic polymers. However, seasonal changes in the relative importance of each polymer, along with changes in the abundance and flux rates, indicate that there would be seasonal variability in the type of microparticles exported. Changes in composition occurred between stations and between the head and mouth of the river, suggesting particle retention due to either deposition, degradation, or biological consumption. Full article