Search Results (406)

This manuscript presents the results from the synthesis and characterization of a slag analogue with a nominal composition of 17 wt% LiMnO₂ and 83 wt% Ca₂SiO₄ encountering fairly high cooling rates in order to study the evolution of Mn-species. The Mn species was also simulated from 1223 K to 1773 K using a thermodynamic model, assuming a homogeneous melt. The micro-composition including the Mn species of the solidified slag was determined experimentally, and was used as basis for molecular dynamics (MD) simulation. The MD simulation provides information on structure and viscosity at high temperatures, which are otherwise difficult to access. These parameters significantly influence oxidation state of redox-active elements and the solidified product. The micro-composition analyzed by electron probe micro analysis (EPMA) and synchrotron-based micro-X-ray fluorescence (micro-XRF) showed that Mn-rich and Ca-Si-rich phases are separated. While the Mn-O phases did not contain noticeable Ca, the Ca₂SiO₄ phase had incorporated 0.6 wt% of Mn. The slag solidified into round-shaped and droplet-shaped grains of a Li-Mn-oxide, some Mn₃O₄ and Ca₂SiO₄. The powder X-ray diffraction (PXRD) confirmed the formation of larnite; the identity of the Li-Mn-oxide, however, remained inconclusive. The Mn oxidation state (OS) was identified using synchrotron-based micro-X-ray absorption near edge spectroscopy (micro-XANES). The Mn-O grains matched well with Li-Mn-oxides and a Mn OS: +3, e.g., LiMn³⁺O₂. Small areas matching hausmannite (Mn²⁺Mn₂³⁺O₄) were also identified. The OS of Mn in the silicate phase could not be identified. For comparison, a slowly cooled slag analogue with similar composition, but higher Si content, was also subjected to micro-XANES. The slowly cooled slag formed long Mn-rich needles in a matrix of large calcium silicate crystals. The Mn-rich crystals matched well with the XANES spectrum of a Mn³⁺ Li-oxide like LiMn³⁺O₂. At the rim of the needles, the Mn-spectra matched well the hausmannite (Mn²⁺Mn₂³⁺O₄) reference. In the silicate phases, Mn had an OS: +2, unambiguously. The melt structure at different temperatures of two compositions, i.e., LiMn³⁺O₂ and Ca₂SiO₄, was simulated using molecular dynamics (MD). They serve as model compositions, assuming a heterogeneous melt. The results show significant different degrees of polymerization and viscosity. Information from MD simulations can support the identification of potentially different oxygen permeability and with that prediction of oxidation states. The bulk composition was identified by inductively coupled plasma optical emission spectrometry (ICP-OES), bulk structure by PXRD and bulk species by lab-XANES. The synchrotron micro analysis including micro-XRD were performed at the microfocus beamline I18 at the Diamond Light Source. Pure reference compounds were prepared and characterized with the same multi-modal approach. Full article

Osteoporosis and other degenerative bone diseases pose significant challenges to global healthcare systems due to their prevalence and impact on quality of life. Current treatments often alleviate symptoms without fully restoring damaged bone tissue, highlighting the need for innovative approaches like stem cell therapy. Adipose-derived mesenchymal stem cells (ADMSCs) are particularly promising due to their accessibility, abundant supply, and strong differentiation potential. However, ADMSCs tend to favor adipogenic pathways, necessitating the use of differentiation inducers (DIs), three-dimensional (3D) hydrogel environments, and photobiomodulation (PBM) to achieve targeted osteogenic differentiation. This study investigated the combined effects of osteogenic DIs, a fast-dextran hydrogel matrix, and PBM at specific wavelengths and fluences on the proliferation and differentiation of immortalized ADMSCs into osteoblasts. Near-infrared (NIR) and green (G) light, as well as their combination, were used with fluences of 3 J/cm², 5 J/cm², and 7 J/cm². The results showed statistically significant increases in alkaline phosphatase levels, a marker of osteogenic differentiation, with G light at 7 J/cm² demonstrating the most substantial impact on ADMSC differentiation. Calcium deposits, visualized by Alizarin red S staining, appeared as early as 24 h post-treatment in PBM groups, suggesting accelerated osteogenic differentiation. ATP luminescence assays indicated increased proliferation in all experimental groups, particularly with NIR and NIR-G light at 3 J/cm² and 5 J/cm². MTT viability and LDH membrane permeability assays confirmed enhanced cell viability and stable cell health, respectively. In conclusion, PBM significantly influences the differentiation and proliferation of hydrogel-embedded immortalized ADMSCs into osteoblast-like cells, with G light at 7 J/cm² being particularly effective. These findings support the combined use of 3D hydrogel matrices and PBM as a promising approach in regenerative medicine, potentially leading to innovative treatments for degenerative bone diseases. Full article

S100 calcium-binding protein B (S100B) is a protein primarily known as a biomarker for central nervous system (CNS) injuries, reflecting blood–brain barrier (BBB) permeability and dysfunction. Recently, S100B has also been implicated in cardiovascular diseases, including heart failure (HF). Thus, we investigated serum levels of S100B in 146 chronic HF patients from the Cognition.Matters-HF study and their association with cardiac and cognitive dysfunction. The median S100B level was 33 pg/mL (IQR: 22–47 pg/mL). Higher S100B levels were linked to longer HF duration (p = 0.014) and increased left atrial volume index (p = 0.041), but also with a higher prevalence of mild cognitive impairment (p = 0.023) and lower visual/verbal memory scores (p = 0.006). In a multivariable model, NT-proBNP levels independently predicted S100B (T-value = 2.27, p = 0.026). S100B did not impact mortality (univariable HR (95% CI) 1.00 (0.99–1.01); p = 0.517; multivariable HR (95% CI) 1.01 (1.00–1.03); p = 0.142), likely due to its reflection of acute injury rather than long-term outcomes and the mild HF phenotype in our cohort. These findings underscore S100B’s value in comprehensive disease assessment, reflecting both cardiac dysfunction and potentially related BBB disruption. Full article

According to many research groups, high glucose induces the overproduction of superoxide anions, with reactive oxygen species (ROS) generally being considered the link between high glucose levels and the toxicity seen at cellular levels. Respiratory complex anomalies can lead to the production of ROS. Calcium [Ca²⁺] at physiological levels serves as a second messenger in many physiological functions. Accordingly, mitochondrial calcium [Ca²⁺]_m overload leads to ROS production, which can be lethal to the mitochondria through various mechanisms. F1F0-ATPase (ATP synthase or complex V) is the enzyme responsible for catalyzing the final step of oxidative phosphorylation. This is achieved by F1F0-ATPase coupling the translocation of protons in the mitochondrial intermembrane space and shuttling them to the mitochondrial matrix for ATP synthesis to take place. Mitochondrial complex V T8993G mutation specifically blocks the translocation of protons across the intermembrane space, thereby blocking ATP synthesis and, in turn, leading to Neuropathy, Ataxia, and Retinitis Pigmentosa (NARP) syndrome. This study seeks to explore the possibility of [Ca²⁺]_m overload mediating the pathological roles of high glucose in defective respiratory chain-mediated mitochondrial stress. NARP cybrids are the in vitro experimental models of cells with F1FO-ATPase defects, with these cells harboring 98% of mtDNA T8993G mutations. Their counterparts, 143B osteosarcoma cell lines, are the parental cell lines used for comparison. We observed that NARP cells mediated and enhanced the death of cells (apoptosis) when incubated with hydrogen peroxide (H₂O₂) and high glucose, as depicted using the MTT assay of cell viability. Furthermore, using fluorescence probe-coupled laser scanning confocal imaging microscopy, NARP cells were found to significantly enable mitochondrial reactive oxygen species (mROS) formation and enhance the depolarization of the mitochondrial membrane potential (ΔΨm). Elucidating the mechanisms of sugar-enhanced toxicity on the mitochondria may, in the future, help to alleviate the symptoms of patients with NARP syndromes and other neurodegenerative diseases. Full article

Nephrotic syndrome is a clinical syndrome characterized by massive proteinuria, called nephrotic range proteinuria (over 3.5 g per day in adults or 40 mg/m² per hour in children), hypoalbuminemia, oncotic edema, and hyperlipidemia, with an increasing incidence over several years. Nephrotic syndrome carries severe morbidity and mortality risk. The main pathophysiological event in nephrotic syndrome is increased glomerular permeability due to immunological, paraneoplastic, genetic, or infective triggers. Because of the marked increase in the glomerular permeability to macromolecules and the associated urinary loss of albumins and hormone-binding proteins, many metabolic and endocrine abnormalities are present. Some of them are well known, such as overt or subclinical hypothyroidism, growth hormone depletion, lack of testosterone, vitamin D, and calcium deficiency. The exact prevalence of these disorders is unknown because of the complexity of the human endocrine system and the differences in their prevalence. This review aims to comprehensively analyze all potential endocrine and hormonal complications of nephrotic syndrome and, vice versa, possible kidney complications of endocrine diseases that might remain unrecognized in everyday clinical practice. Full article

A series of microbial-induced carbonate precipitation (MICP) experiments were conducted using Sporosarcina pasteurii to reinforce coastal soft clay in Zhejiang. By analyzing the physical and mechanical parameters of samples of varying ages, specifically focusing on each sample’s unconfined compressive strength, triaxial shear strength, and permeability coefficient, it was revealed that MICP technology can be used effectively to reinforce coastal clay. The unconfined compressive strength of treated soil increased by 23% compared to untreated soil, while the permeability coefficient decreased by 75%. The internal friction angle of the clay remained almost constant, whereas cohesion significantly increased by approximately 53%. One-dimensional compression experiments were also performed, yielding consolidation parameters such as the compression coefficient, compression index, and consolidation coefficient. The results indicated a notable decrease in the soil compression index. Furthermore, microscopic analysis revealed that clay particles were cemented by calcium carbonate, whose precipitation was induced by the bacteria. Our XRD results also indicated that the bacteria facilitated the conversion of Ca²⁺ present in the soil into calcium carbonate. Full article

The instability and collapse of boreholes during coal seam gas extraction significantly affect the effectiveness of gas extraction. In response, this study selected human hair residue as the base material for composite protein foaming agents, leveraging the high protein content of animal hoof and hair materials to develop a high-strength, high-permeability, and environmentally friendly new type of foam concrete. This research found that the optimal ratio of foaming agent base solution to water is 1:4 when sodium hydroxide is used for protein hydrolysis. Comparing the foaming effects of sodium dodecyl sulfate (K12), α-sodium alpha-alkenyl sulfonate (AOS), sodium lauryl polyoxyethylene ether sulfate (SLS), and sodium dodecyl benzene sulfonate (LAS), sodium lauryl polyoxyethylene ether sulfate (SLS) exhibited the best foaming performance, while α-sodium alpha-alkenyl sulfonate (AOS) had the best foam stability. The optimal foam performance was achieved by mixing 2.0 g per liter of sodium lauryl polyoxyethylene ether sulfate and 0.3% calcium stearate. The experimental results showed that this foam concrete, with 25 mL of foaming agent, has a high strength exceeding 11 MPa and a high permeability with an average of 2.13 MD. This paper utilizes environmentally friendly materials and preparation processes. By using renewable resources such as human hair residue as raw materials, it helps reduce the dependence on natural resources and promotes sustainable development. This research demonstrates significant sustainability and provides the mining industry with an eco-friendly and efficient solution, with the potential to achieve positive economic and environmental benefits in practical applications. Full article

In this study, the protein and salts distribution (Ca, P, Na and Mg) in processed cheese (PC) samples prepared with 180 or 360 mEq/kg of the calcium sequestering salts (CSS) disodium phosphate (DSP), disodium pyrophosphate (DSPP), sodium hexametaphosphate (SHMP) and trisodium citrate (TSC) was studied. For this purpose, a water-soluble extract (WSE) of PC samples was prepared. All PC samples contained 45–46% moisture, 26–27% fat and 20–21% protein and had a pH of 5.2 or 5.7. Ultracentrifugation slightly reduced the protein content of the WSE of PC, indicating that most protein in the WSE was non-sedimentable. At equal concentration of CSS, the protein content of the WSE was higher for PC at pH 5.7 compared to PC at pH 5.2. Approximately 55–85% of the Ca and P in the WSE of samples was 10 kDa-permeable for PC prepared with DSPP and SHMP. This suggests that the formation of non-permeable Ca–polyphosphate–casein complexes. For PC prepared with TSC, >90% of Ca in the WSE was 10 kDa-permeable, indicating that micellar disruption arises from sequestration of micellar Ca. These results indicate that the WSE method is an appropriate method to understand how salts present in PC are distributed. However, the WSE and ultracentrifugal supernatant of the WSE can include both soluble and protein-associated salts. Therefore, determining levels of salts in 10 kDa permeate of ultracentrifugal supernatant of the WSE is most appropriate. Full article

Overdose of acetaminophen (APAP) produces fulminant hepatic necrosis. The underlying mechanism of APAP hepatotoxicity involves mitochondrial dysfunction, including mitochondrial oxidant stress and the onset of mitochondrial permeability transition (MPT). Reactive oxygen species (ROS) play an important role in APAP-induced hepatotoxicity, and iron is a critical catalyst for ROS formation. This review summarizes the role of mitochondrial ROS formation in APAP hepatotoxicity and further focuses on the role of iron. Normally, hepatocytes take up Fe³⁺-transferrin bound to transferrin receptors via endocytosis. Concentrated into lysosomes, the controlled release of iron is required for the mitochondrial biosynthesis of heme and non-heme iron-sulfur clusters. After APAP overdose, the toxic metabolite, NAPQI, damages lysosomes, causing excess iron release and the mitochondrial uptake of Fe²⁺ by the mitochondrial calcium uniporter (MCU). NAPQI also inhibits mitochondrial respiration to promote ROS formation, including H₂O₂, with which Fe²⁺ reacts to form highly reactive •OH through the Fenton reaction. •OH, in turn, causes lipid peroxidation, the formation of toxic aldehydes, induction of the MPT, and ultimately, cell death. Fe²⁺ also facilitates protein nitration. Targeting pathways of mitochondrial iron movement and consequent iron-dependent mitochondrial ROS formation is a promising strategy to intervene against APAP hepatotoxicity in a clinical setting. Full article

Aquaporins (AQPs) are transmembrane channels initially discovered for their role in water flux facilitation through biological membranes. Over the years, a much more complex and subtle picture of these channels appeared, highlighting many other solutes accommodated by AQPs and a dense regulatory network finely tuning cell membranes’ water permeability. At the intersection between several transduction pathways (e.g., cell volume regulation, calcium signaling, potassium cycling, etc.), this wide and ancient protein family is considered an important therapeutic target for cancer treatment and many other pathophysiologies. However, a precise and isoform-specific modulation of these channels function is still challenging. Among the modulators of AQPs functions, cations have been shown to play a significant contribution, starting with mercury being historically associated with the inhibition of AQPs since their discovery. While the comprehension of AQPs modulation by cations has improved, a unifying molecular mechanism integrating all current knowledge is still lacking. In an effort to extract general trends, we reviewed all known modulations of AQPs by cations to capture a first glimpse of this regulatory network. We paid particular attention to the associated molecular mechanisms and pinpointed the residues involved in cation binding and in conformational changes tied up to the modulation of the channel function. Full article

As an important gelling material, cementitious materials are widely used in civil engineering construction. Currently, research on these materials is conducted using experimental and numerical image processing methods, which enable the observation and analysis of structural changes and mechanical properties. These methods are instrumental in designing cementitious materials with specific performance criteria, despite their resource-intensive nature. The material genome approach represents a novel trend in material research and development. The establishment of a material gene database facilitates the rapid and precise determination of relationships between characteristic genes and performance, enabling the bidirectional design of cementitious materials’ composition and properties. This paper reviews the characteristic genes of cementitious materials from nano-, micro-, and macro-scale perspectives. It summarizes the characteristic genes, analyzes expression parameters at various scales, and concludes regarding their relationship to mechanical properties. On the nanoscale, calcium hydrated silicate (C-S-H) is identified as the most important characteristic gene, with the calcium–silicon ratio being the key parameter describing its structure. On the microscale, the pore structure and bubble system are key characteristics, with parameters such as porosity, pore size distribution, pore shape, air content, and the bubble spacing coefficient directly affecting properties like frost resistance, permeability, and compressive strength. On the macroscale, the aggregate emerges as the most important component of cementitious materials. Its shape, angularity, surface texture (grain), crushing index, and water absorption are the main characteristics influencing properties such as chloride ion penetration resistance, viscosity, fluidity, and strength. By analyzing and mapping the relationship between these genes and properties across different scales, this paper offers new insights and establishes a reference framework for the targeted design of cementitious material properties. Full article

Nano-calcium carbonate (NC) is a novel ultrafine solid powder material that possesses quantum size effects, small size effects, surface effects, and macroscopic quantum effects that ordinary calcium carbonate lacks. As a nanomaterial with superior properties, graphene oxide (GO) has been studied extensively in the field of construction. In microscopic characterization, the reaction between NC and tricalcium aluminate (C₃A) formed a new hydration product, hydrated calcium aluminum carbonate (C₃A·CaCO₃·11H₂O), which enhanced the arrangement of hydration products and optimized the distribution of pore size in the mortar. Regarding the mechanical properties, the addition of GO and NC significantly enhanced the early-age mechanical performance of the mortar. In terms of durability, the incorporation of GO and NC significantly improved the water permeability, chloride ion permeability, and resistance to sulfate attack of the cement mortar. In this study, it was found that adding 1 wt% NC and 0.02 wt% GO not only improves the mechanical and durability properties but also promotes the hydration reaction according to the microstructure analysis. With the help of NC, compared with other studies, the amount of GO is reduced, while the cost is reduced, and the application of GO in the field of cement-based materials is promoted. Full article

This study investigates the enhancement of hydraulic lime mortar (HLM) using varying contents of metakaolin (MK) to improve its application in the restoration of historic buildings. Samples from historic structures were analyzed, and the effects of different MK contents on the physical and mechanical properties of HLM were examined. The reaction mechanism and microstructural changes were evaluated using XRD and SEM analysis. The results indicated that increasing MK levels in HLM led to a decrease in fluidity, with fluidity reducing by 4.8% at 12% MK. The addition of MK increased water consumption for standard consistency by 5.4% and shortened the final setting time by 10.2%. MK consumption promoted secondary hydration, enhancing compressive strength by up to 98.1% and flexural strength by up to 55.1%, and increasing bonding strength by 26.9%. The density of HLM improved with MK addition, slightly reducing moisture content by 4.5% and water absorption by 4.6%, while the water vapor transmission properties decreased by 50.9%, indicating reduced porosity. The elastic modulus of the mortar increased significantly from 2.19 GPa to 7.88 GPa with the addition of MK, enhancing rigidity and crack resistance. The optimal blend for restoration materials was found to be 9.0% MK and 25.0% heavy calcium carbonate and was characterized by moderate mechanical strength, enhanced early strength, commendable permeability, minimal risk of cracking, and ease of application. This blend is highly suitable for the rehabilitation of historic structures. Full article

Water scarcity in Tunisia’s semi-arid regions necessitates advanced brackish water desalination solutions. This study evaluates the long-term performance and fouling characteristics of the largest brackish water reverse osmosis desalination plant in southern Tunisia over a period of 5026 days. The plant employs two-stage spiral-wound membrane elements to treat groundwater with a salinity of 3.2 g L⁻¹. The pre-treatment process includes oxidation, sand filtration, and cartridge filtration, along with polyphosphonate antiscalant dosing. Membrane performance was assessed through the analysis of operational data, standardization of permeate flow (Q_ps) and salt passage (SP_s), and the calculation of water (A), solute (B), and ionic (B_j) permeability coefficients. Over the operational period, there was an increase in operating pressure, pressure drop, and permeate conductivity, accompanied by a gradual increase in SP_s as well as in the solute B and ionic B_j permeability coefficients. The average B increased by 82%, reflecting a decrease in solute rejection over time. Additionally, the ionic permeability coefficients for both SO₄²⁻ and Cl⁻ ions increased, with Cl⁻ showing an 88% increase and SO₄²⁻ showing an 87% increase. The produced water’s salinity increased by 67%, indicating a significant loss of membrane performance. To identify the cause of these problems, membrane characterization was analyzed using visual inspection, X-ray fluorescence (XRF), and Fourier transform infrared spectroscopy (FTIR). The characterization revealed the complex nature of the foulants, with a predominant presence of calcium sulfate, along with minor quantities of calcite, dolomite, and silica. The extent of CaSO₄ deposition suggests poor antiscaling efficiency, highlighting the critical importance of selecting an effective antiscalant to mitigate membrane fouling. Full article

Earth–rock dams are widely distributed in China and play an important role in flood control, water storage, water-level regulation, and water quality improvement. As an emerging seepage control and reinforcement technology in the past few years, enzyme (urease)-induced calcium carbonate precipitation (EICP) has the qualities of durability, environmental friendliness, and great economic efficiency. For EICP-solidified standard sand, this study analyzes the effect of dry density, amount of cementation, standing time, perfusion method, and other factors on the permeability and strength characteristics of solidified sandy soil by conducting a permeability test and an unconfined compression test and then working out the optimal solidification conditions of EICP. Furthermore, a quantitative relationship is established between the permeability coefficient (PC), unconfined compressive strength (UCS), and CaCO₃ generation (CG). The test findings indicate that the PC of the solidified sandy soil decreases and the UCS rises as the starting dry density, amount of cementation, and standing time rise. With the increase of CG, the PC of the solidified sandy soil decreases while the UCS increases, indicating a good correlation among PC, UCS, and CG. The optimal condition of solidification by EICP is achieved by the two-stage grouting method with an initial dry density of 1.65 g/cm³, cementation time of 6 d, and standing time of 5 d. Under such conditions, the permeability of the solidified sandy soil is 6.25 × 10⁻⁴ cm/s, and the UCS is 1646.94 kPa. The findings of this study are of great theoretical value and scientific significance for guiding the reinforcement of earth–rock dams. Full article