Search Results (936)

Bluetooth Low Energy (BLE) mesh networks provide flexible and reliable communication among low-power sensor-enabled Internet of Things (IoT) devices, enabling them to communicate in a flexible and robust manner. Nonetheless, the majority of existing BLE-based mesh protocols operate as flooding-based piconet or scatternet overlays on top of existing Bluetooth star topologies. In contrast, the Ad hoc On-Demand Distance Vector (AODV) protocol used primarily in wireless ad hoc networks (WAHNs) is forwarding-based and therefore more efficient, with lower overheads. However, the packet delivery ratio (PDR) and link recovery time for AODV performs worse compared to flooding-based BLE protocols when encountering link disruptions. We propose the Multipath Optimized AODV (M-O-AODV) protocol to address these issues, with improved PDR and link robustness compared with other forwarding-based protocols. In addition, M-O-AODV achieved a PDR of 88%, comparable to the PDR of 92% for flooding-based BLE, unlike protocols such as Reverse-AODV (R-AODV). Also, M-O-AODV was able to perform link recovery within 3700 ms in the case of node failures, compared with other forwarding-based protocols that require 4800 ms to 6000 ms. Consequently, M-O-AODV-based BLE mesh networks are more efficient for wireless sensor-enabled IoT environments. Full article

Background: To manage pain and stiffness of the lumbar spine, thrust manipulation is commonly used. High-velocity, small-amplitude thrust manipulation often elicits audible sounds. What causes this audible sound remains unclear, and its clinical significance has not been shown. This study aimed to identify how audible sound affects brainwave activity following a side-lying right rotatory thrust manipulation in a group of healthy individuals. Methods: This was a quasi-experimental repeated measures study design in which 44 subjects completed the study protocol. A portable Bluetooth EEG device was used to capture brainwave activity. The environment was controlled during testing to minimize any factors influencing the acquisition of real-time EEG data. After a short accommodation period, initial brainwaves were measured. Following this, each subject underwent a lumbar 4–5 side-lying right rotatory thrust manipulation, immediately followed by a second brainwave measurement. A third measurement took place one minute later, followed by a fourth one at the three-minute mark. Results: 21 subjects did not experience audible sounds, while 23 subjects experienced audible sounds. Both groups had significant changes measured by the 14 electrodes (p < 0.05). The audible group had more significant changes, which lasted only two minutes. Conclusion: The lack of brainwave response differences between the audible and non-audible groups implies no direct, measurable placebo or beneficial effect from the audible sound. This study could not identify a benefit from the audible sound during an HVLA manipulation of the subjects. Full article

This paper presents a novel waste-heat-powered, wireless, and battery-less Industrial Internet of Things (IIoT) device designed for predictive maintenance in Industry 4.0 environments. With a focus on real-time quality data, this device addresses the limitations of current battery-operated IIoT devices, such as energy consumption, transmission range, data rate, and constant quality of service. It is specifically developed for heat-intensive industries (e.g., iron and steel, cement, petrochemical, etc.), where self-heating nodes, low-power processing platforms, and industrial sensors align with the stringent requirements of industrial monitoring. The presented IIoT device uses thermoelectric generators based on the Seebeck effect to harness waste heat from any hot surface, such as pipes or chimneys, ensuring continuous power without the need for batteries. The energy that is recovered can be used to power devices using mid-range wireless protocols like Bluetooth 5.0, minimizing the need for extensive in-house wireless infrastructure and incorporating light-edge computing. Consequently, up to 98% of cloud computation efforts and associated greenhouse gas emissions are reduced as data is processed within the IoT device. From the environmental perspective, the deployment of such self-powered IIoT devices contributes to reducing the carbon footprint in energy-demanding industries, aiding their digitalization transition towards the industry 5.0 paradigm. This paper presents the results of the most challenging energy harvesting technologies based on an all-silicon micro thermoelectric generator with planar architecture. The effectiveness and self-powering ability of the selected model, coupled with an ultra-low-power processing platform and Bluetooth 5 connectivity, are validated in an equivalent industrial environment to monitor vibrations in an electric machine. This approach aligns with the EU’s strategic objective of achieving net zero manufacturing capacity for renewable energy technologies, enhancing its position as a global leader in renewable energy technology (RET). Full article

Building Management Systems (BMSs) are transitioning from utilising wired installations to wireless Internet of Things (IoT) sensors and actuators. This shift introduces the requirement of robust localisation methods which can link the installed sensors to the correct Control Units (CTUs) which will facilitate continued communication. In order to lessen the installation burden on the technicians, the installation process should be made more complicated by the localisation method. We propose an automated version of the fingerprinting-based localisation method which estimates the location of sensors with room-level accuracy. This approach can be used for initialisation and maintenance of BMSs without introducing additional manual labour from the technician installing the sensors. The method is extended to two proposed localisation methods which take advantage of knowledge present in the building plan regarding the distribution of sensors in each room to estimate the location of groups of sensors at the same time. Through tests using a simulation environment based on a Bluetooth-based measurement campaign, the proposed methods showed an improved accuracy from the baseline automated fingerprinting method. The results showed an error rate of 1 in 20 sensors (if the number of sensors per room is known) or as few as 1 per 200 sensors (if a group of sensors are deployed and detected together for one room at a time). Full article

Improving the performance at signalized intersections can be achieved through different management styles or sensor technologies. It is crucial that we measure the real-time impact of these variables on intersection performance. This study introduces a Bluetooth-based real-time performance measurement system applicable to all signalized intersections. Additionally, the developed method serves as a feedback tool for adaptive intersection management systems, providing valuable data input for performance optimization. The method developed in the study is applied at the Refik Cesur Intersection in the Polatlı district of Ankara where delay values are calculated based on traffic flows and data from Bluetooth sensors positioned at strategic locations. Initially, the intersection operated under a fixed-time signaling system, followed by a fully adaptive signaling system the next day. The performance of these two systems is compared using the Bluetooth-based application. The results show that the average delay per vehicle per day is 58.1 seconds/vehicle for the fixed-time system and 45.3 seconds/vehicle for the adaptive system. To validate the Bluetooth-based performance measurement system, the intersection is modeled and simulated using Aimsun Simulation Software Next 20.0.4. The simulation results confirm the findings of the Bluetooth-based analysis, demonstrating the effectiveness of the adaptive signaling system in reducing delays. Full article

The emergence of AIGC has significantly improved design efficiency, enriched creativity, and promoted innovation in the design industry. However, whether the content generated from its own database meets the preferences of target users still needs to be determined through further testing. This study investigates the appeal of AI-generated stylized products to users, utilizing 12 images as stimuli in conjunction with eye-tracking technology. The stimulus is composed of top-selling gender-based stylized Bluetooth earphones from the Taobao shopping platform and the gender-based stylized earphones generated by the AIGC software GPT4.0, categorized into three experimental groups. An eye-tracking experiment was conducted in which 44 participants (22 males and 22 females, mean age = 21.75, SD = 2.45, range 18–27 years) observed three stimuli groups. The eye movements of the participants were measured while viewing product images. The results indicated that variations in stimuli category and gender caused differences in fixation durations and counts. When presenting a mix of the two types of earphones, the AIGC-generated earphones and earphones from the Taobao shopping platform, the two gender groups both showed a significant effect in fixation duration with F (2, 284) = 3.942, p = 0.020 < 0.05, and η = 0.164 for the female group and F (2, 302) = 8.824, p < 0.001, and η = 0.235 for the male group. They all had a longer fixation duration for the AI-generated earphones. When presenting exclusively the two types of AI-generated gender-based stylized earphones, there was also a significant effect in fixation duration with F (2, 579) = 4.866, p = 0.008 < 0.05, and η = 0.129. The earphones generated for females had a longer fixation duration. Analyzing this dataset from a gender perspective, there was no significant effect when the male participants observed the earphones, with F (2, 304) = 1.312 and p = 0.271, but there was a significant difference in fixation duration when the female participants observed the earphones (F (2, 272) = 4.666, p = 0.010 < 0.05, and η = 0.182). The female participants had a longer fixation duration towards the earphones that the AI generated for females. Full article

Indoor positioning is the key enabling technology for many location-aware applications. As GPS does not work indoors, various solutions are proposed for navigating devices. Among these solutions, Bluetooth low energy (BLE) technology has gained significant attention due to its affordability, low power consumption, and rapid data transmission capabilities, making it highly suitable for indoor positioning. Received signal strength (RSS)-based positioning has been studied intensively for a long time. However, the accuracy of RSS-based positioning can fluctuate due to signal attenuation and environmental factors like crowd density. Angle of arrival (AoA)-based positioning uses angle measurement technology for location devices and can achieve higher precision, but the accuracy may also be affected by radio reflections, diffractions, etc. In this study, a dual-branch convolutional neural network (CNN)-based BLE indoor positioning algorithm integrating RSS and AoA is proposed, which exploits both RSS and AoA to estimate the position of a target. Given the absence of publicly available datasets, we generated our own dataset for this study. Data were collected from each receiver in three different directions, resulting in a total of 2675 records, which included both RSS and AoA measurements. Of these, 1295 records were designated for training purposes. Subsequently, we evaluated our algorithm using the remaining 1380 unseen test records. Our RSS and AoA fusion algorithm yielded a sub-meter accuracy of 0.79 m, which was significantly better than the 1.06 m and 1.67 m obtained when using only the RSS or the AoA method. Compared with the RSS-only and AoA-only solutions, the accuracy was improved by 25.47% and 52.69%, respectively. These results are even close to the latest commercial proprietary system, which represents the state-of-the-art indoor positioning technology. Full article

Wearable smart devices have gradually become indispensable devices in people’s lives. Their security and privacy have gained increasing popularity among the public due to their ability to monitor and record various aspects of users’ daily activities and health data. These devices maintain a wireless connection with mobile phones through periodic signal transmissions, which can be intercepted and analyzed by external observers. While these signal packets contain valuable information about the device owner, the identity of the actual user remains unknown. In this study, we propose two approaches to link wearable smart devices with users’ mobile phones, which serve as electronic identities, to enable novel applications such as multi-device authentication and user-device graph construction for targeted advertising. To establish this linkage, we propose two approaches: a passive-sniffing-based linking approach and an active-interference-based linking approach, which solve the problem of sniffing Bluetooth Low Energy broadcast packets in two stages of Bluetooth Low Energy communication. Through experiments conducted across three scenarios, we demonstrate that seven wearable devices can be successfully linked with an accuracy rate exceeding 80%, with accuracy rates approaching 100% when a device is recorded more than 11 times. Additionally, we find that four wearable devices can be linked via an active-interference-based linking approach with an accuracy rate exceeding 70%. Our results highlight the potential of wearable devices and mobile phones as a means of establishing user identities and enabling the development of more sophisticated applications in the field of wearable technology. Full article

This article demonstrates the integration of sensor fusion for pose estimation and data collection in tennis balls, aiming to create a smaller, less intrusive form factor for use in progressive learning during tennis practice. The study outlines the design and implementation of the Bosch BNO055 smart sensor, which features built-in managed sensor fusion capabilities. The article also discusses deriving additional data using various mathematical and simulation methods to present relevant orientation information from the sensor in Unity. Embedded within a Vermont practice foam tennis ball, the final prototype product communicates with Unity on a laptop via Bluetooth. The Unity interface effectively visualizes the ball’s rotation, the resultant acceleration direction, rotations per minute (RPM), and the orientation relative to gravity. The system successfully demonstrates accurate RPM measurement, provides real-time visualization of ball spin and offers a pathway for innovative applications in tennis training technology. Full article

Background/Objectives: Autism spectrum disorder (ASD) is a lifelong neurodevelopmental condition characterised by impairments in social communication, sensory abnormalities, and attentional deficits. Children with ASD often face significant challenges with speech perception and auditory attention, particularly in noisy environments. This study aimed to assess the effectiveness of noise cancelling Bluetooth earbuds (Nuheara IQbuds Boost) in improving speech perception and auditory attention in children with ASD. Methods: Thirteen children aged 6–13 years diagnosed with ASD participated. Pure tone audiometry confirmed normal hearing levels. Speech perception in noise was measured using the Consonant-Nucleus–Consonant-Word test, and auditory/visual attention was evaluated via the Integrated Visual and Auditory Continuous Performance Task. Participants completed these assessments both with and without the IQbuds in situ. A two-week device trial evaluated classroom listening and communication improvements using the Listening Inventory for Education-Revised (teacher version) questionnaire. Results: Speech perception in noise was significantly poorer for the ASD group compared to typically developing peers and did not change with the IQbuds. Auditory attention, however, significantly improved when the children were using the earbuds. Additionally, classroom listening and communication improved significantly after the two-week device trial. Conclusions: While the noise cancelling earbuds did not enhance speech perception in noise for children with ASD, they significantly improved auditory attention and classroom listening behaviours. These findings suggest that Bluetooth earbuds could be a viable alternative to remote microphone systems for enhancing auditory attention in children with ASD, offering benefits in classroom settings and potentially minimising the stigma associated with traditional assistive listening devices. Full article

To establish ubiquitous and energy-efficient wireless sensor networks (WSNs), short-range Internet of Things (IoT) devices require Bluetooth low energy (BLE) technology, which functions at 2.4 GHz. This study presents a novel approach as follows: a fully integrated all-digital phase-locked loop (ADPLL)-based Gaussian frequency shift keying (GFSK) modulator incorporating two-point modulation (TPM). The modulator aims to enhance the efficiency of BLE communication in these networks. The design includes a time-to-digital converter (TDC) with the following three key features to improve linearity and time resolution: fast settling time, low dropout regulators (LDOs) that adapt to process, voltage, and temperature (PVT) variations, and interpolation assisted by an analog-to-digital converter (ADC). It features a digital controlled oscillator (DCO) with two key enhancements as follows: ΔΣ modulator dithering and hierarchical capacitive banks, which expand the frequency tuning range and improve linearity, and an integrated, fast-converging least-mean-square (LMS) algorithm for DCO gain calibration, which ensures compliance with BLE 5.0 stable modulation index (SMI) requirements. Implemented in a 28 nm CMOS process, occupying an active area of 0.33 mm², the modulator demonstrates a wide frequency tuning range of from 2.21 to 2.58 GHz, in-band phase noise of −102.1 dBc/Hz, and FSK error of 1.42% while consuming 1.6 mW. Full article

Sarcopenia is an age-related syndrome characterized by the loss of skeletal muscle mass and function. Community screening, commonly used in early diagnosis, usually lacks features such as real-time monitoring, low cost, and convenience. This study introduces a promising approach to sarcopenia screening by dynamic plantar pressure monitoring. We propose a wearable flexible-printed piezoelectric sensing array incorporating barium titanate thin films. Utilizing a flexible printer, we fabricate the array with enhanced compressive strength and measurement range. Signal conversion circuits convert charge signals of the sensors into voltage signals, which are transmitted to a mobile phone via Bluetooth after processing. Through cyclic loading, we obtain the average voltage sensitivity (4.844 mV/kPa) of the sensing array. During a 6 m walk, the dynamic plantar pressure features of 51 recruited participants are extracted, including peak pressures for both sarcopenic and control participants before and after weight calibration. Statistical analysis discerns feature significance between groups, and five machine learning models are employed to screen for sarcopenia with the collected features. The results show that the features of dynamic plantar pressure have great potential in early screening of sarcopenia, and the Support Vector Machine model after feature selection achieves a high accuracy of 93.65%. By combining wearable sensors with machine learning techniques, this study aims to provide more convenient and effective sarcopenia screening methods for the elderly. Full article

In the current scenario, renewable energy resources play a vital role in developing countries. Photovoltaic panel-based power plants have great significance for the production of electrical energy, due to automated transitions, easy interaction, and low maintenance costs. The energy-production efficiency depends on various factors and environmental effects. The formulation of a thin layer of dust particles on solar panels diminishes their energy-production capacity due to the limiting of heat transfer to the semiconducting materials. The current paper deals with the design and fabrication of an automated water-jet-assisted robot used to clean the dust particle layer and bird droppings on PV panels. In the water-jet-assisted cleaning robot, there is a two-brush mechanism that works in concert with the rover’s movement. A Bluetooth communication system plays a vital role by controlling the rover; this approach offers a perspective on a rover constructed with an Arduino-UNO micro-controller, along with an HC-05 Bluetooth sensor. Full article

Bluetooth Low Energy (BLE) is a prominent short-range wireless communication protocol widely extended for communications and sensor systems in consumer electronics and industrial applications, ranging from manufacturing to retail and healthcare. The BLE protocol provides four generic access profile (GAP) roles when it is used in its low-energy version, i.e., ver. 4 and beyond. GAP roles control connections and allow BLE devices to interoperate each other. They are defined by the Bluetooth special interest group (SIG) and are primarily oriented to connect peripherals wirelessly to smartphones, laptops, and desktops. Consequently, the existing GAP roles have characteristics that do not fit well with vehicular communications in cooperative intelligent transport systems (C-ITS), where low-latency communications in high-density environments with stringent security demands are required. This work addresses this gap by developing two new GAP roles, defined at the application layer to meet the specific requirements of vehicular communications, and by providing a service application programming interface (API) for developers of vehicle-to-everything (V2X) applications. We have named this new approach ITS-BLE. These GAP roles are intended to facilitate BLE-based solutions for real-world scenarios on roads, such as detecting road traffic signs or exchanging information at toll booths. We have developed a prototype able to work indistinctly as a unidirectional or bidirectional communication device, depending on the use case. To solve security risks in the exchange of personal data, BLE data packets, here called packet data units (PDU), are encrypted or signed to guarantee either privacy when sharing sensitive data or authenticity when avoiding spoofing, respectively. Measurements taken and their later evaluation demonstrated the feasibility of a V2X BLE network consisting of picocells with a radius of about 200 m. Full article

The OHIO (Odin Hospital Indoor cOmpass) project received funding from the European Union’s Horizon 2020 research and innovation action program, via ODIN–Open Call, which is issued and executed under the ODIN project and focuses on enhancing hospital safety, productivity, and quality by introducing digital solutions, such as the Internet of Things (IoT), robotics, and artificial intelligence (AI). OHIO aims to enhance the productivity and quality of medical equipment maintenance activities within the pilot hospital, “Le Scotte” in Siena (Italy), by leveraging internal informational resources. OHIO will also be completely integrated with the ODIN platform, taking advantage of the available services and functionalities. OHIO exploits Bluetooth Low Energy (BLE) tags and antennas together with the resources provided by the ODIN platform to develop a complex ontology-based IoT framework, which acts as a central cockpit for the maintenance of medical equipment through a central management web application and an indoor real-time location system (RTLS) for mobile devices. The application programmable interfaces (APIs) are based on REST architecture for seamless data exchange and integration with the hospital’s existing computer-aided facility management (CAFM) and computerized maintenance management system (CMMS) software. The outcomes of the project are assessed both with quantitative and qualitative methods, by evaluating key performance indicators (KPIs) extracted from the literature and performing a preliminary usability test on both the whole system and the graphic user interfaces (GUIs) of the developed applications. The test implementation demonstrates improvements in maintenance timings, including a reduction in maintenance operation delays, duration of maintenance tasks, and equipment downtime. Usability post-test questionnaires show positive feedback regarding the usability and effectiveness of the applications. The OHIO framework enhanced the effectiveness of medical equipment maintenance by integrating existing software with newly designed, enhanced interfaces. The research also indicates possibilities for scaling up the developed methods and applications to additional large-scale pilot hospitals within the ODIN network. Full article