Search Results (1,549)

Multi-component ultra-high-temperature ceramics (MC-UHTCs) are promising for high-temperature applications due to exceptional thermo-mechanical properties, yet their wear characteristics remain unexplored. Herein, the wear behavior of binary (Ta, Nb)C, ternary (Ta, Nb, Hf)C, and quaternary (Ta, Nb, Hf, Ti)C UHTCs synthesized via spark plasma sintering (SPS) is investigated. Gradual addition of equimolar UHTC components improves the wear resistance of MC-UHTCs, respectively, by ~29% in ternary UHTCs and ~49% in quaternary UHTCs when compared to binary UHTCs. Similarly, the penetration depth decreased from 115.14 mm in binary UHTCs to 73.48 mm in ternary UHTCs and 44.41 mm in quaternary UHTCs. This has been attributed to the complete solid solutioning, near-full densification and higher hardness (~up to 30%) in quaternary UHTCs. Analysis of the worn-out surface suggests pull-out, radial, and edge micro-cracking and delamination as the dominant wear mechanisms in binary and ternary UHTCs. However, grain deformation and minor delamination are the dominant wear mechanisms in quaternary UHTCs. This study underscores the potential of MC-UHTCs for tribological applications where material experiences removal and inelastic deformation under high mechanical loading. Full article

Refractory superalloys (RSAs) are promising candidates for high-temperature, high-strength applications. Two-phase RSAs containing body-centered cubic (BCC) and ordered B2 phases are among the more promising candidates. Systems containing Ru-based B2 precipitates exhibit stable two-phase microstructures at temperatures in excess of 1600 °C. The present study experimentally investigated one potential foundational ternary system for these alloys, Nb-Ti-Ru. Two alloys, (Nb₃Ti)_0.85Ru_0.15 and (Nb₄Ti)_0.85Ru_0.15, were studied to determine phase equilibria and properties at temperatures between 900 °C and 1300 °C. The B2 phase was found to be dominated by RuTi ordering, although considerable Nb solubility was observed up to 18 mol %. The Nb-rich BCC matrix contained up to 15 mol % Ru and 20 mol % Ti. Although a two-phase microstructure of B2 precipitates in a BCC matrix was confirmed, the distribution of elements in the two phases resulted in a larger lattice misfit than expected. The results obtained in this investigation provide valuable information for the future development of RSAs utilizing Ru-based B2 strengthening precipitates. Full article

The metavolcanic rocks around Maroua in the Far North Region of Cameroon are located at the northern margin of the Central African Fold Belt (CAFB) and have not been studied to date. The petrographic and whole-rock geochemical data presented in this paper highlight their magma genesis and geodynamic evolution. The lavas are characterized by basaltic, andesitic, and dacitic compositions and belong to the calc-alkaline medium-K and low-K tholeiite series. The mafic samples are essentially magnesian, while the felsic samples are ferroan. On a chondrite-normalized REE diagram, mafic and felsic rocks display fractionated patterns, with light REE enrichment and heavy REE depletion (La_N/Yb_N = 1.41–5.38). The felsic samples display a negative Eu anomaly (Eu/Eu* = 0.59–0.87), while the mafic lavas are characterized by a positive Eu anomaly (Eu/Eu* = 1.03–1.35) or an absence thereof. On a primitive mantle-normalized trace element diagram, the majority of the samples exhibit negative Ti and Nb–Ta anomalies (0.08–0.9 and 0.54–0.74, respectively). These characteristic features exhibited by the metavolcanic rocks of Maroua are similar to those of subduction-zone melts. This subduction would have taken place after the convergence between the Congo craton (Adamawa-Yadé domain) and the Saharan craton (Western Cameroonian domain). Petrological modelling using major and trace elements suggests a derivation of the Maroua volcanics from primitive parental melts generated by the 5–10% partial melting of a source containing garnet peridotite, probably generated during the interaction between the subducted continental crust and the lithospheric mantle and evolved chemically through fractional crystallization and assimilation. Full article

Micro-arc oxidation (MAO) films were fabricated on the Ti-39Nb-6Zr alloy at different voltages in the silicate and silicate/glycerin electrolyte. Their morphology, phase structure and composition were characterized by scanning electron microscopy (SEM) with energy dispersive X-ray spectroscopy (EDS), X-ray diffraction (XRD) and X-ray photoelectron spectroscopy (XPS). It was found that the glycerin additive in the silicate electrolyte improved the compactness of the MAO film. The corrosion resistance was evaluated, and the influence of glycerin additive in electrolyte on the growth of micro-arc oxidized film was revealed by optical emission spectra. Full article

In response to the poor wear resistance and high-temperature oxidation resistance of titanium alloys during service, a series of lightweight refractory high-entropy alloys (RHEAs) can be designed for the laser cladding coating of titanium alloy surfaces, with due consideration of the compositional and structural characteristics of titanium alloys. Firstly, the structural stability, mechanical and thermal properties of four lightweight RHEAs (MoNbTiV, AlMoNbTiW, CrMoNbTiV, and AlCrMoNbTiV) with equal atomic ratios were designed and calculated using first principles combined with quasi-harmonic approximation (QHA). The results indicate that all four RHEAs are stable BCC, exhibiting elastic anisotropy and ductility. The lightest density is 6.409 g/cm³. Adding Al/Cr can cause structural distortion and affect its mechanical properties. Their Young’s moduli are in the following order: AlCrMoNbTiV > MoNbTiV > CrMoNbTiV > AlMoNbTiV. The thermal expansion coefficients of the four RHEAs and titanium alloys are very close, with a difference in linear expansion coefficient of less than 1.16 × 10⁻⁵/K. Meanwhile, the metallurgical bonding of four types of RHEA coatings was successfully achieved on a Ti-6Al-4V(TC4) substrate through laser cladding technology, and all coatings exhibited a unique BCC solid solution phase. Full article

Titanium alloys have a high cost of production and exhibit low resistance to abrasive wear. The objective of this work was to carry out diamond-like carbon (DLC) coating, with dissimilar thicknesses, on Ti-22Nb-6Zr titanium alloys produced by powder metallurgy, and to evaluate its microabrasive wear resistance. The samples were compacted, cold pressed, and sintered, producing substrates for coating. The DLC coatings were carried out by PECVD (plasma-enhanced chemical vapor deposition). Free sphere microabrasive wear tests were performed using alumina (Al₂O₃) abrasive suspension. The DLC-coated samples were characterized by scanning electron microscopy (SEM), Vickers microhardness, coatings adhesion tests, confocal laser microscopy, atomic force microscopy (AFM), and Raman spectroscopy. The coatings did not show peeling-off or delamination in adhesion tests. The PECVD deposition was effective, producing sp2 and sp3 mixed carbon compounds characteristic of diamond-like carbon. The coatings provided good structural quality, homogeneity in surface roughness, excellent coating-to-substrate adhesion, and good tribological performance in microabrasive wear tests. The low wear coefficients obtained in this work demonstrate the excellent potential of DLC coatings to improve the tribological behavior of biocompatible titanium alloy parts (Ti-22Nb-6Zr) produced with a low modulus of elasticity (closer to the bone) and with near net shape, given by powder metallurgy processing. Full article

NaNbO₃-based ferroelectric composites are regarded as a highly promising typical energy storage material. In this work, 0.02xMnO₂−(1−x)NaNbO₃−xBi0.5Na_0.5TiO₃ composites were prepared by the solid-state sintering method and their microstructure, energy storage performance, and temperature stability were analyzed. As observed by the SEM images, the addition of Bi_0.5Na_0.5TiO₃ to NaNbO₃ in appropriate amounts can effectively suppress grain growth, which is beneficial for improving the breakdown field strength. When x = 0.3, an optimal value of 210 kV/cm is achieved. Meanwhile, as 2θ = 33.2°, the most intense XRD peak can be observed, indicating excellent solid solubility between the phase components. Consequently, 0.006MnO₂–0.7NaNbO₃–0.3Bi_0.5Na_0.5TiO₃ composites demonstrated an impressive discharging storage density of 2.464 J/cm³ and a considerable energy storage efficiency of 85.8%. In addition, within the temperature range of 30–80 °C, the fluctuation in energy storage density remains below 10%. All the above performances indicate that this type of material exhibits excellent practicality in the field of pulse power supply. Full article

In this paper, we developed models for 21 quinary high-entropy transition metal carbide ceramics (HETMCCs), composed of carbon and the transition metals Ti, Zr, Mo, V, Nb, W, and Ta, employing the Special Quasirandom Structures (SQS) method. We investigated how the transition metal elements influence lattice distortion, mixing enthalpy, Gibbs free energy of mixing, and the electronic structure of the systems through first-principles calculations. The calculations show that 21 systems can form a stable single phase, among which (TiMoVNbTa)C₅, (ZrMoNbWTa)C₅, and (MoVNbWTa)C₅ exhibit superior stability. The formation energy and migration energy of carbon vacancies in systems with strong single-phase stability were calculated to predict their radiation resistance. The formation energy of carbon vacancies is closely related to the types of surrounding transition metal elements, with values ranging between the maximum and minimum formation energies observed in binary transition metal carbides (TMCs). The range of migration energy for carbon vacancies is wider than that observed in TMCs, which can hinder their long-range migration and enhance the radiation resistance of the materials. Full article

Fe–Ni–Co–Al-based systems have attracted a lot of interest due to their large recoverable strain. In this study, the microstructure and thermal cycling behaviors of Fe₄₁Ni₂₈Co₁₇Al_11.5Ti_1.25Nb_1.25 (at.%) 98.5% cold-rolled alloys after annealing treatment at 1277 °C for 1 h, followed by aging for 48 h at 600 °C, were investigated. From the electron backscatter diffraction results, we see that the texture intensity increased from 9.4 to 16.5 mud and the average grain size increased from 300 to 400 μm as the annealing time increased from 0.5 h to 1 h. The hardness results for different aging heat treatment conditions show the maximum value was reached for samples aged at 600 °C for 48 h (peak aging condition). The orientation distribution functions (ODFs) displayed by Goss, brass, and copper were the main textural features in the FeNiCoAlTiNb cold-rolled alloy. After annealing, strong Goss and brass textures were formed. The transmission electron microscopy (TEM) results show that the precipitate size was ~10 nm. The X-ray diffraction (XRD) results show a strong peak in the (111) and (200) planes of the austenite (⁠⁠γ, FCC) structure for the annealed sample. After aging, a new peak in the (111) plane of the precipitate (⁠⁠γ′, L12) structure emerged, and the peak intensity of austenite (⁠⁠γ, FCC) decreased. The magnetization–temperature curves of the aged sample show that both the magnetization and transformation temperature increased with the increasing magnetic fields. The shape memory properties show a fully recoverable strain of up to 2% at 400 MPa stress produced in the three-point bending test. However, the experimental recoverable strain values were lower than the theoretical values, possibly due to the fact that the volume fraction of the low-angle grain boundary (LABs) was small compared to the reported values (60%), and it was insufficient to suppress the beta phases. The beta phases made the grain boundaries brittle and deteriorated the ductility. On the fracture surface of samples after the three-point bending test, the fracture spread along the grain boundary, and the cross-section microstructural results show that the faces of the grain boundary were smooth, indicating that the grain boundary was brittle with an intergranular fracture. Full article

A series of Sr_1−xDy_xTi_1−yNb_yO_3−δ (0.05 ≤ x, y ≤ 0.10) samples were fabricated using cold compaction, followed by sintering in a (95% N₂ + 5% H₂) reducing atmosphere. We studied the crystal structure and optical properties of Sr_1−xDy_xTi_1−yNb_yO_3−δ using X-ray diffraction (XRD) with Rietveld refinement, scanning electron microscopy (SEM), X-ray photoelectron spectroscopy (XPS), and ultraviolet−visible−near-infrared (UV−VIS−NIR) spectroscopy. The sintered Sr_1−xDy_xTi_1−yNb_yO_3−δ had a tetragonal structure (I4/mcm space group). In the sintered samples, Ti ions existed as a mixture of Ti³⁺ and Ti⁴⁺, and Nb ions existed as a mixture of Nb⁴⁺ and Nb⁵⁺. The band-gap energies decreased with increasing Dy/Nb concentrations. The incorporation of Ti and Nb ions, the formation of both Ti³⁺ and Nb⁴⁺ ions, and the reduction in band-gap energies are likely highly effective for increasing the electron concentration and the corresponding electrical conductivity. Sr_1−xDy_xTi_1−yNb_yO_3−δ with high electrical conductivity is suitable for energy and electronics applications. Full article

Mica is a kind of important rock-forming mineral in the lithosphere of Earth, which can be a superior tool used to trace the origin and late evolution of rock. The Jian forsterite jade (a kind of geological skarn) is an emerging kind of gemstone in China with a beautiful color and luster, discovered in Ji’an County, Jilin Province, Northeast China. It is mainly composed of rare Mg-rich forsterite (Mg^# (Mg/(Mg + Fe²⁺) up to 99), serpentine and brucite. The source of hydrothermal fluid triggering the late metamorphism (the serpentinization of forsterite) of forsterite jade deposits remains unclear. We report a series of phlogopites with a regular range of mineral compositions in the forsterite jade deposit. Micrographs show that the phlogopites are associated with forsterite and coexist with serpentine in forsterite jade, tourmaline and tremolite in the contact zone, and plagioclase in pegmatite, and the related replacement of phlogopite seems to have not occurred. The phlogopites that occurred as single grains or veinlets in forsterite jade named type I are characterized by high X_Mg, ranging from ~0.98 to ~0.95, and the phlogopites that occurred in the contact zone of forsterite jade and pegmatite named type II are rich in Fe, with a range of X_Mg from ~0.82 to ~0.66. Additionally, the type II phlogopites are also rich in Ti, Mn, Cl, Li, Rb, Zn, V, Co, Nb and Ta but poor in Na, Sr and F compared to the type I phlogopite. Petrological and mineralogical characteristics and geochemical compositions suggest that the phlogopites are crystallized from the corresponding fluid component by hydrothermal metasomatism. The abundant Mg of the fluid phase is produced during the serpentinization of forsterite, triggered by pegmatitic hydrothermal fluid, and other main materials like K, Al, Si and H₂O are provided by the intrusive pegmatite. With the occurrence of and regular compositional variation in phlogopites in the forsterite jade deposit, we suppose that the hydrothermal fluid triggering the serpentinization of the Jian forsterite jade is produced by the intrusive pegmatite. Full article

A novel TiB₂-CeO₂-modified (Nb,Mo,Cr,W)Si₂ coating was prepared on a Nb-5W-2Mo-1Zr alloy substrate using two-step slurry sintering and halide-activated pack cementation to address the limitations of a single NbSi₂ coating in meeting the service requirements of niobium alloys at elevated temperatures. At 1700 °C, the static oxidation life of the coating exceeded 20 h, thus indicating excellent high-temperature oxidation resistance. This was due to the formation of a TiO₂-SiO₂-Cr₂O₃ composite oxide film on the coating surface, which, due to low oxygen permeability, effectively prevented the inward infiltration of oxygen. Additionally, the dense structure of the composite coating further enhanced this protective effect. The composite coating was able to withstand over 1600 thermal shock cycles from room temperature to 1700 °C, and its excellent thermal shock performance could be attributed to the formation of MoSi₂, CrSi₂, and WSi₂ from elements such as Mo, Cr, and W, which were added during modification. In addition to adjusting the difference in thermal expansion coefficients between the layers of composite coatings to reduce the thermal stress generated by thermal shock cycles, the formation of silicide compounds also improved the overall fracture toughness of the coating and thereby improved its thermal shock resistance. Full article

In order to obtain large room-temperature electrocaloric effect (ECE) and wide operation temperature range simultaneously in lead-free ceramics, we proposed designing a relaxor ferroelectric with a T_m (the temperature at which the maximum dielectric permittivity is achieved) near-room temperature and glass addition. Based on this strategy, we designed and fabricated lead-free 0.76NaNbO₃–0.24BaTiO₃ (NN-24BT) ceramics with 1wt.% BaO–B₂O₃–SiO₂ glass addition, which showed distinct relaxor ferroelectric characteristics with strongly diffused phase transition and a T_m near-room temperature. Based on a direct measurement method, a large ΔT (adiabatic temperature change) of 1.3 K was obtained at room temperature under a high field of 11.0 kV mm⁻¹. Additionally, large ECE can be maintained (>0.6 [email protected] kV mm⁻¹) over a broad temperature range from 23 °C to 69 °C. Moreover, the ECE displayed excellent cyclic stability with a variation in ΔT below ±7% within 100 test cycles. The comprehensive ECE performance is significantly better than other lead-free ceramics. Our work provides a general and effective approach to designing lead-free, high-performance ECE ceramics, and the approach possesses the potential to be utilized to improve the ECE performance of other lead-free ferroelectric ceramic systems. Full article

Wide varieties of igneous rocks are extensively utilized as stones for decoration purposes and as a potential source for building. With the use of petrological (mineralogical and chemical) and physico-mechanical analyses, the current work accurately mapped the Dokhan Volcanics (DV) and utilized them as decorative stones and their prospective in building materials using Frattini’s test. Field observations indicate that metavolcanics, DV, and monzogranites are the principal rock units exposed in the studied area. The DV rocks are characterized by a dense series of stratified, rhyolitic to andesitic lava interspersed with a few pyroclastics. Andesite, andesite porphyry, dacite, and rhyolite are the primary representatives of the selected DV. The lack of infrequent appearance of mafic units in the current volcanic eruptions indicates that the primary magma is not mantle-derived. This is supported by their Mg# (17.86–33.57). Additionally, the examined DV rocks have Y/Nb ratios above 1.2, suggesting a crustal source. The role of fractionation is interpreted by their variation from andesite passing through dacite to rhyolite, which is indicated by gradual negative distribution groups between silica and TiO₂, Fe₂O₃, CaO, MgO, Co, and Cu from andesite to rhyolitic lava. Additionally, a wide range of widely used DV rocks like Y/Nb, Rb/Zr, and Ba/Nb point to crustal contamination in the rhyolitic rocks. The partial melting of the lower crust can produce andesitic magma, which ascend to higher crustal levels and form lava of calc-alkaline. A portion of this lava may split, settle at shallow crustal depths, and undergo differentiation to create the DV rocks. Based on the results of physico-mechanical properties, the studied samples met the requirements for natural stone to be used as decorative stones, whether as interior or exterior installations. The pozzolanic assessment of the studied rocks revealed their usability as supplementary cementitious materials in the building sector. Full article

The corrosion behavior of the TiTaNbZrAg alloys with different amounts of tantalum (0%, 10% and 20%) and with distinct surface topography (smooth and rough) was investigated in phosphate buffer solution (PBS) for long-time immersion (1000 h). By this approach, we expect to bring about new insights into the influence of both the amount of Ta in the alloy composition and the surface topography on the corrosion behavior of the Ti-based alloys. The corrosion resistance was studied by Open Circuit Potential (OCP), Potentiodynamic Polarization (PP), and Electrochemical Impedance Spectroscopy (EIS). From the potentiodynamic investigations, it was observed that all types of samples showed good corrosion resistance (i.e., R_corr < 10 µm y⁻¹) and may be used successfully for medical applications. However, the samples with smooth surfaces and with a certain amount of Ta (10% and 20%) exhibit the best corrosion performance (R_corr < 1 µm y⁻¹). As regards the samples with rough surfaces, the results evidenced that they showed lower corrosion resistance (1 < R_corr < 3 µm y⁻¹), suggesting that the Ta presence does not necessarily hinder the corrosion processes. Actually, the synergetic effect of both the presence of Ta and surface roughness plays an important role in corrosion resistance. Full article