Daikin RXC-B (R32) Manual Service

DAMA-SM-20-002
Service Manual / Inverter Split Wall Mounted Type (A)FTXC Series
Service
Manual
Inverter Split
Wall Mounted Type (A)FTXC Series
DAMA-SM-20-002
[Applied Models]
z Inverter Split : Heat Pump Unit
DAMA-SM-20-002
Introduction .................................................................................... 1
1. Safety Cautions.......................................................................................2
1.1 Warnings and Cautions Regarding Safety of Workers.............................2
1.2 Warnings and Cautions Regarding Safety of Users.................................8
2. Icons Used ............................................................................................10
3. Revision History ....................................................................................11
Part 1 General Information .......................................................... 12

1. What is Inverter? ...................................................................................13
2. Inverter Basics ......................................................................................14
3. Names and Functions of Inverter Components.....................................15
4. Applicable Models .................................................................................16
Part 2 Specifications.................................................................... 18
1. Specification Data .................................................................................19
2. Functions...............................................................................................25
Part 3 Functions and Control ....................................................... 27

1. Main Functions......................................................................................28
1.1 Temperature Control ..............................................................................28
1.2 Frequency Principle................................................................................28
1.3 Airflow Direction Control.........................................................................30
1.4 Fan Speed Control for Indoor Unit .........................................................30
1.5 Dry Mode................................................................................................31
1.6 Automatic Operation...............................................................................32
1.7 Thermostat Control.................................................................................33
1.8 ECO+ Operation ...................................................................................34
1.9 Sleep Mode ............................................................................................35
1.10 POWERFUL Operation ..........................................................................35
1.11 Other Functions......................................................................................36
2. Thermistor Functions ............................................................................37
3. Control Specification .............................................................................38
3.1 Mode Hierarchy ......................................................................................38
3.2 Frequency Control..................................................................................39
3.3 Standby Electricity Saving (Suspend Function) .....................................41
3.4 Controls at Mode Changing/Start-up......................................................41
3.5 Discharge Pipe Temperature Control.....................................................43
3.6 Input Current Control..............................................................................44
3.7 Freeze-up Protection Control .................................................................45
3.8 Heating Peak-cut Control .......................................................................46
3.9 Outdoor Fan Control...............................................................................47
3.10 Liquid Compression Protection Function................................................48
3.11 Defrost Control .......................................................................................48
3.12 Electronic Expansion Valve Control .......................................................49
3.13 Malfunctions ...........................................................................................53
i Table of Contents
DAMA-SM-20-002
Part 4 Remote Controller ............................................................. 54

1. Applicable Remote Controller ...............................................................55
2. BRC52B66 ............................................................................................56
Part 5 Service Diagnosis .............................................................. 57

1. General Problem Symptoms and Check Items .....................................58
2. Troubleshooting with LED .....................................................................59
2.1 Indoor Unit..............................................................................................59
2.2 Outdoor Unit ...........................................................................................60
3. Error Diagnosis .....................................................................................60
3.1 To enter error diagnosis .........................................................................60
4. Troubleshooting ....................................................................................61
4.1 Error Codes and Description ................................................................. 61
4.2 Indoor Unit PCB Abnormality .................................................................63
4.4 Indoor Fan Motor (DC Motor) or Related Abnormality ...........................65
4.5 Thermistor or Related Abnormality (Indoor Unit)....................................66
4.7 Low-voltage Detection or Over-voltage Detection..................................68
4.8 Signal Transmission Error (Between Indoor Unit and Outdoor Unit)......69
4.9 Installation error......................................................................................71
4.10 Outdoor Unit PCB Abnormality...............................................................72
4.11 OL Activation (Compressor Overload) ...................................................73
4.12 Compressor Lock ...................................................................................75
4.13 DC Fan Lock ..........................................................................................76
4.14 Input Overcurrent Detection ...................................................................77
4.16 High Pressure Control in Cooling ...........................................................80
4.17 Compressor System Sensor Abnormality ..............................................82
4.18 Position Sensor Abnormality ..................................................................83
4.19 Thermistor or Related Abnormality (Outdoor Unit).................................84
4.23 Electrical Box Temperature Rise............................................................92
4.24 Radiation Fin Temperature Rise ............................................................93
4.25 Output Overcurrent Detection ................................................................94
4.26 Four Way Valve Abnormality..................................................................96
5. Actuator Check......................................................................................98
5.1 Thermistor Resistance Check ................................................................98
5.2 Power Supply Waveform Check.............................................................99
5.3 Electronic Expansion Valve Check.........................................................99
5.4 Four Way Valve Performance Check ...................................................100
5.5 Inverter Unit Refrigerant System Check...............................................101
5.6 Rotation Pulse Check on the Outdoor Unit PCB ..................................101
5.7 Installation Condition Check.................................................................102
5.8 Discharge Pressure Check...................................................................102
5.9 Outdoor Fan System Check .................................................................103
5.10 Main Circuit Short Check......................................................................103
5.11 Power Module Check ...........................................................................105
Table of Contents ii
DAMA-SM-20-002
Part 6 Trial Operation and Field Settings .................................. 105

1. Pump Down Operation........................................................................106
2. Forced Cooling Operation ...................................................................107
3. Silicone Grease on Power Transistor/Diode Bridge............................108
Part 7 Appendix .......................................................................... 109

1. Piping Diagrams..................................................................................110
1.1 Indoor Unit............................................................................................110
1.2 Outdoor Unit .........................................................................................112
2. Wiring Diagrams..................................................................................114
2.1 Indoor Unit............................................................................................114
2.2 Outdoor Unit .........................................................................................115
2.3 Printed Circuit Board Connector Wiring Diagram.................................116
3. Operation Limit....................................................................................119
4. Transmission Monitor [TM2016-1] Operation Instructions ..................120
4.1 Names and Functions of Parts .............................................................120
4.2 Basic Operations and Display ..............................................................121
iii Table of Contents

DAMA-SM-20-002
Introduction
1. Safety Cautions.......................................................................................2
1.1 Warnings and Cautions Regarding Safety of Workers.............................2
1.2 Warnings and Cautions Regarding Safety of Users.................................8
2. Icons Used ............................................................................................10
3. Revision History ....................................................................................11
Introduction 1
Safety Cautions DAMA-SM-20-002
1. Safety Cautions
Be sure to read the following safety cautions before conducting repair work.
After the repair work is complete, be sure to conduct a test operation to ensure that the
equipment operates normally, and explain the cautions for operating the product to the
customer.
This manual is for the This appliance is
person in charge of filled with R-32.
maintenance and
inspection.
Caution Items The caution items are classified into Warning and Caution. The Warning items are
especially important since death or serious injury can result if they are not followed closely. The
Caution items can also lead to serious accidents under some conditions if they are not
followed. Therefore, be sure to observe all the safety caution items described below.
Pictograms This symbol indicates an item for which caution must be exercised.
The pictogram shows the item to which attention must be paid.
This symbol indicates a prohibited action.
The prohibited item or action is shown in the illustration or near the symbol.
This symbol indicates an action that must be taken, or an instruction.
The instruction is shown in the illustration or near the symbol.
1.1 Warnings and Cautions Regarding Safety of Workers

Warning
Do not store equipment in a room with fire sources (e.g., naked
flames, gas appliances, electric heaters).
Be sure to disconnect the power cable from the socket before

disassembling equipment for repair.
Working on equipment that is connected to the power supply may cause
an electrical shock.
If it is necessary to supply power to the equipment to conduct the repair or
inspect the circuits, do not touch any electrically charged sections of the
equipment.
If refrigerant gas is discharged during repair work, do not touch the
discharged refrigerant gas.
Refrigerant gas may cause frostbite.
When disconnecting the suction or discharge pipe of the

compressor at the welded section, evacuate the refrigerant gas
completely at a well-ventilated place first.
If there is gas remaining inside the compressor, the refrigerant gas or
refrigerating machine oil discharges when the pipe is disconnected, and it
may cause injury.
If refrigerant gas leaks during repair work, ventilate the area.
Refrigerant gas may generate toxic gases when it contacts flames.
Be sure to discharge the capacitor completely before conducting

repair work.
The step-up capacitor supplies high-voltage electricity to the electrical
components of the outdoor unit.
A charged capacitor may cause an electrical shock.
2 Introduction
DAMA-SM-20-002 Safety Cautions
Warning
Do not turn the air conditioner on or off by plugging in or
unplugging the power cable.
Plugging in or unplugging the power cable to operate the equipment may
cause an electrical shock or fire.
Be sure to wear a safety helmet, gloves, and a safety belt when

working in a high place (more than 2 m).
Insufficient safety measures may cause a fall.
In case of R-32 refrigerant models, be sure to use pipes, flare nuts

and tools intended for the exclusive use with the R-32 refrigerant.
The use of materials for R-22 refrigerant models may cause a serious
accident, such as a damage of refrigerant cycle or equipment failure.
Do not mix air or gas other than the specified refrigerant (R-32 /
R-22) in the refrigerant system.
If air enters the refrigerant system, an excessively high pressure results,
causing equipment damage and injury.
Caution
Do not repair electrical components with wet hands.
Working on the equipment with wet hands may cause an electrical shock.
Do not clean the air conditioner with water.

Washing the unit with water may cause an electrical shock.
Be sure to provide an earth / grounding when repairing the

equipment in a humid or wet place, to avoid electrical shocks.
Be sure to turn off the power switch and unplug the power cable
when cleaning the equipment.
The internal fan rotates at a high speed, and may cause injury.
Be sure to conduct repair work with appropriate tools.

The use of inappropriate tools may cause injury.
Be sure to check that the refrigerating cycle section has cooled

down enough before conducting repair work.
Working on the unit when the refrigerating cycle section is hot may cause
burns.
Conduct welding work in a well-ventilated place.

Using the welder in an enclosed room may cause oxygen deficiency.
Introduction 3
Safety Checklist
 Checking the area
Before beginning work, conduct safety checks to minimise the risk of ignition. When
repairing the refrigerating system, take the following precautions before work.
 Work procedure
Work shall be conducted under a controlled procedure so as to minimise the risk of working
in the presence of R-32 or vapour.
 General working area

All maintenance staff and others working in the local area shall be instructed on the nature of
work being carried out.
Work in confined spaces shall be avoided.
The area around the workspace shall be sectioned off. Ensure that the conditions within the
area have been made safe by control of flammable materials.
 Checking for presence of refrigerant

The working area shall be checked with an appropriate refrigerant detector before and
during work, to ensure the technician is aware of potentially flammable atmospheres.
Ensure that the leak detection equipment being used is suitable for use with R-32, i.e.
non-sparking, adequately sealed or intrinsically safe.
 Fire extinguishing equipment

If any hot work is to be conducted on the refrigeration equipment or any associated parts,
appropriate fire extinguishing equipment shall be made available at hand. Prepare a dry
powder or CO2 fire extinguisher adjacent to the working area.
 No ignition sources
During work on a refrigeration system which involves exposing any piping work that contains
or has contained R-32, any sources of ignition shall not be used in a manner that may lead
to the risk of fire or explosion. All possible ignition sources, including cigarette smoking,
should be kept at a safe distance from the site of installation, repairing, or removing space.
Before starting work, the area around the equipment shall be examined to make sure that
there are no flammable hazard or ignition risks. No Smoking signs shall be displayed.
 Ventilated area
Ensure that the working area is open or that it is adequately ventilated before work.
Adequate ventilation shall be maintained during the entire period of work.
The ventilation should disperse any released refrigerant and preferably discharge it into the
external atmosphere.
 Checking the refrigeration equipment

Where electrical components are to be changed, the new components shall be fit for the
purpose and have the correct specifications.
The manufacturer's maintenance and service guidelines shall be followed at all times.
If there are any unclear points, consult the manufacturer's technical department for
assistance.
The following checks shall be applied to any installation work involving R-32:
 The amount of charge is in accordance with the size of the room where the refrigerant
containing parts are installed;
 The ventilation machinery and outlets are operating adequately and are not obstructed;
 If an indirect refrigerating circuit is being used, the secondary circuit shall be checked for
the presence of refrigerant;
 Marking on the equipment is visible and legible. Markings and signs that are illegible
shall be corrected;
 Refrigeration pipes or components are installed in a position where they are unlikely to
be exposed to any substance which may corrode refrigerant containing components, or
the refrigerant containing components are constructed of materials which are inherently
resistant to corrosion or are suitably protected against corrosion.
4 Introduction
Safety Checklist (con't)

 Checking electrical devices
Repair and maintenance to electrical components shall include initial safety checks and
component inspection procedures. In case there is any fault that could endanger safety, no
electrical supply shall be connected to the circuit until the fault is satisfactorily dealt with.
Initial safety checks shall include:
 that capacitors are discharged: this shall be done in a safe manner to avoid possibility of
sparking;
 that no live electrical components and wiring are exposed while charging, recovering or
purging the system;
 that the equipment is earthed at all times.
 Repairs to sealed components

During repairs to sealed components, all electrical supplies shall be disconnected from the
equipment being worked upon before the removal of any sealed covers, etc. If it is absolutely
necessary to have power supplied to equipment during servicing, continuously operating
leak detection shall be installed at the most dangerous point of the system in order to warn of
a potentially hazardous situation.
Particular attention shall be paid to the following: ensure that working on electrical
components does not alter the casing in such a way that affects the level of protection
including damage to cables, excessive number of connections, terminals different from the
original specification, damage to seals, incorrect fitting of glands, etc.
Ensure that the equipment is mounted securely.
Ensure that seals or sealing materials have not degraded such that they no longer serve the
purpose of preventing the ingression of flammable atmospheres. Replacement parts shall be
in accordance with the manufacturer's specifications.
The use of silicon sealant may inhibit the effectiveness of some types of leak detection
equipment. Intrinsically safe components do not have to be isolated before working on them.
 Repair to intrinsically safe components

Do not apply any permanent inductive or capacitance load to the circuit without ensuring that
this will not exceed the permissible voltage and current for the equipment in use.
Only intrinsically safe components can be worked on in the presence of a flammable
atmosphere.
The test apparatus shall be of correct rating.
Replace components only with parts specified by the manufacturer. Using other parts may
result in ignition of the refrigerant leaked into the atmosphere.
 Wiring
Check that wiring is not subject to wear, corrosion, excessive pressure, vibration, sharp
edges or any other adverse environmental effects. The check shall also take into account
the effects of ageing or continuous vibration from sources such as compressors or fans.
 Detecting of R-32
Under no circumstances shall potential sources of ignition be used in the search for or
detection of refrigerant leaks. A halide torch (or any other detector using a naked flame) shall
not be used.
Introduction 5

 Leak detection methods
The following leak detection methods can be applied for systems containing R-32.
Electronic leak detectors shall be used to detect R-32, but the sensitivity may not be
adequate or may need re-calibration (detection equipment shall be calibrated in a
refrigerant-free area). Ensure that the detector is not a potential source of ignition and that it
is suitable for the refrigerant used. Leak detection equipment shall be set to the percentage
of the lower flammability limit (LFL) of the refrigerant and calibrated to fit the refrigerant
employed. The appropriate percentage of gas (maximum 25%) shall be confirmed.
Leak detection fluids are suitable for use with most refrigerants but the use of detergents
containing chlorine shall be avoided as the chlorine may react with the refrigerant and
corrode the copper piping work.
If a leak is suspected, all naked flames shall be removed or extinguished.
If a refrigerant leakage which requires brazing is found, all of the refrigerant shall be
recovered from the system, or isolated (by means of shut off valves) in a part of the system
remote from the point of the leakage. Oxygen free nitrogen (OFN) shall then be purged
through the system both before and during the brazing process.
 Removal and evacuation

When breaking the refrigerant circuit to make repairs or any other purpose, conventional
procedures may be used. However, flammability must be taken into consideration. The
following procedure shall be adhered to:
 Remove refrigerant;
 Purge the circuit with inert gas;
 Evacuate the inert gas;
 Purge again with inert gas;
 Carry out cutting or brazing of the circuit.
The refrigerant shall be recovered into the correct recovery cylinders. The system shall be
cleaned with OFN to render the unit safe. (= Flushing) This process may need to be
repeated several times. Compressed air or oxygen shall not be used for this task.
Flushing shall be achieved through breaking the vacuum by filling the system with OFN until
the working pressure is achieved, then venting the OFN into the atmosphere, and finally
pulling the system down to vacuum again. This process shall be repeated until no refrigerant
remains within the system. After the last OFN charge is finished, the system shall be vented
down to atmospheric pressure to enable work. This operation is especially important if
brazing operations on the piping work are to take place.
Ensure that the outlet for the vacuum pump is not close to any ignition sources and that
there is ventilation available.
 Charging procedures
In addition to conventional charging procedures, the following requirements shall be met.
Ensure that the charging equipment to be used is not contaminated by different refrigerants.
Hoses or lines shall be as short as possible to minimise the amount of refrigerant contained
in them.
 Cylinders shall be kept upright.
 Ensure that the refrigeration system is earthed before charging the system with
refrigerant.
 Label the system when charging is complete (if not already).
 Extreme care shall be taken not to overfill the refrigeration system.
Before recharging, the system shall be tested for leakage with OFN. On completion of
charging, the system shall be tested before commissioning. Follow up leakage test shall be
carried out before leaving the site.
6 Introduction

 Decommissioning
Before carrying out this procedure, it is essential that the technician is completely familiar
with the equipment and all its details. It is recommended to train technicians so that all of the
refrigerant is recovered safely. In case analysis is required before re-using the reclaimed
refrigerant, an oil and refrigerant sample shall be taken before proceeding with
decommissioning. It is essential that electrical power is available before work.
(1) Comprehend the equipment and its operation.
(2) Isolate the system electrically.
(3) Before starting work, ensure that:
 mechanical handling equipment is available if required, for handling refrigerant
cylinders;
 protective equipment can be used in compliance with specifications;
 the recovery process is supervised by a competent person at all times;
 recovery equipment and cylinders conform to the appropriate standards.
(4) Pump down the refrigerant system, if possible.
(5) If vacuum can not be ensured, apply a manifold so that refrigerant can be removed from
various parts of the system.
(6) Make sure that the cylinder is situated on the scale before recovery takes place.
(7) Start the refrigerant recovery device and operate it in accordance with the manufacturer's
instructions.
(8) Do not overfill cylinders. (Do not exceed 80% liquid charge volume).
(9) Do not exceed the maximum working pressure of the cylinder, even temporarily.
(10)When the cylinders have been filled correctly and the process is completed, make sure
that the cylinders and the equipment are removed from site promptly and all valves on
the equipment are closed.
(11)Recovered refrigerant shall not be charged into another refrigeration system before it
has been cleaned and checked.
 Labelling
Equipment shall be labelled stating that it has been decommissioned and emptied of
refrigerant. The label shall be dated and signed. Ensure that there are labels on the
equipment stating the equipment contains R-32.
 Refrigerant recovery
When removing refrigerant from a system, either for servicing or decommissioning, it is
recommended to conduct training so that all refrigerants can be removed safely.
When transferring refrigerant into cylinders, ensure that only appropriate refrigerant recovery
cylinders are used.
Ensure that the correct number of cylinders for holding the total system charge are available.
All cylinders to be used must be designated for the recovered refrigerant and labelled for that
refrigerant (i.e. special cylinders for the recovery of refrigerant). Cylinders shall be equipped
with a pressure relief valve and associated shut-off valves in good working order. If possible,
empty recovery cylinders shall be cooled in a separate place before recovery is conducted.
The recovery equipment shall be in good working order with instructions concerning the
equipment at hand, and shall be suitable for the recovery of R-32. In addition, a set of
calibrated weighing scales shall be available and in good working order. Hoses shall be
equipped with leak-free disconnect couplings and in good condition. Before using the
recovery device, check that it has undergone proper maintenance, that it is in satisfactory
working order, and that any associated electrical components are sealed to prevent ignition
in the event of a refrigerant leakage. Consult manufacturer if in doubt.
The recovered refrigerant shall be returned to the refrigerant supplier in the correct recovery
cylinder, with the relevant Waste Transfer Note attached. Do not mix refrigerants in recovery
units and especially not in cylinders.
If compressors or compressor oil are to be removed, ensure that the refrigerant melted into
the oil has been evacuated to an acceptable level to make certain that R-32 does not remain
within the oil. The evacuation process shall be carried out before returning the compressor
to the supplier. Only electric heating to the compressor body shall be employed to accelerate
this process. Oil drained from the system shall be treated safely.
Introduction 7
1.2 Warnings and Cautions Regarding Safety of Users

Warning
Do not store the equipment in a room with fire sources (e.g., naked
flames, gas appliances, electric heaters).
Be sure to use parts listed in the service parts list of the applicable
model and appropriate tools to conduct repair work. Never attempt
to modify the equipment.
The use of inappropriate parts or tools may cause an electrical shock,
excessive heat generation or fire.
If the power cable and lead wires are scratched or have deteriorated,
be sure to replace them.
Damaged cable and wires may cause an electrical shock, excessive heat
generation or fire.
Do not use a joined power cable or extension cable, or share the

same power outlet with other electrical appliances, since it may
cause an electrical shock, excessive heat generation or fire.
Be sure to use an exclusive power circuit for the equipment, and

follow the local technical standards related to the electrical
equipment, the internal wiring regulations, and the instruction
manual for installation when conducting electrical work.
Insufficient power circuit capacity and improper electrical work may cause
an electrical shock or fire.
Be sure to use the specified cable for wiring between the indoor and
outdoor units.
Make the connections securely and route the cable properly so that there
is no force pulling the cable at the connection terminals.
Improper connections may cause excessive heat generation or fire.
When wiring between the indoor and outdoor units, make sure that
the terminal cover does not lift off or dismount because of the cable.
If the cover is not mounted properly, the terminal connection section may
cause an electrical shock, excessive heat generation or fire.
Do not damage or modify the power cable.

Damaged or modified power cables may cause an electrical shock or fire.
Placing heavy items on the power cable, or heating or pulling the power
cable may damage it.
Do not mix air or gas other than the specified refrigerant (R-32 /
R-22) in the refrigerant system.
If air enters the refrigerant system, an excessively high pressure results,
causing equipment damage and injury.
If the refrigerant gas leaks, be sure to locate the leaking point and
repair it before charging the refrigerant. After charging the
refrigerant, make sure that there is no leak.
If the leaking point cannot be located and the repair work must be
stopped, be sure to pump-down, and close the service valve, to prevent
refrigerant gas from leaking into the room. Refrigerant gas itself is
harmless, but it may generate toxic gases when it contacts flames, such
as those from fan type and other heaters, stoves and ranges.
When relocating the equipment, make sure that the new installation
site has sufficient strength to withstand the weight of the
equipment.
If the installation site does not have sufficient strength or the installation
work is not conducted securely, the equipment may fall and cause injury.
8 Introduction
Warning
Check to make sure that the power cable plug is not dirty or loose,
then insert the plug into a power outlet securely.
If the plug is dusty or has a loose connection, it may cause an electrical
shock or fire.
When replacing the coin battery in the remote controller, be sure to

dispose of the old battery to prevent children from swallowing it.
If a child swallows the coin battery, see a doctor immediately.
Caution
Installation of a leakage breaker is necessary in some cases
depending on the conditions of the installation site, to prevent
electrical shocks.
Do not install the equipment in a place where there is a possibility of

combustible gas leaks.
If combustible gas leaks and remains around the unit, it may cause a fire.
Check to see if parts and wires are mounted and connected

properly, and if connections at the soldered or crimped terminals
are secure.
Improper installation and connections may cause excessive heat
generation, fire or an electrical shock.
If the installation platform or frame has corroded, replace it.
A corroded installation platform or frame may cause the unit to fall,
resulting in injury.
Check the earth / grounding, and repair it if the equipment is not

properly earthed / grounded.
Improper earth / grounding may cause an electrical shock.
Be sure to measure insulation resistance after the repair, and make

sure that the resistance is 1 MΩ or higher.
Faulty insulation may cause an electrical shock.
Be sure to check the drainage of the indoor unit after the repair.
Faulty drainage may cause water to enter the room and wet the furniture
and floor.
Do not tilt the unit when removing it.

The water inside the unit may spill and wet the furniture and floor.
Introduction 9
Icons Used DAMA-SM-20-002
2. Icons Used
The following icons are used to attract the attention of the reader to specific information.
Icon Type of Description
Information
Warning Warning is used when there is danger of personal injury.
Warning
Caution Caution is used when there is danger that the reader,
Caution through incorrect manipulation, may damage equipment,
lose data, get an unexpected result or have to restart (part
of) a procedure.
Note Note provides information that is not indispensable, but
Note may nevertheless be valuable to the reader, such as tips
and tricks.
Reference Reference guides the reader to other places in this binder
Reference or in this manual, where he/she will find additional
information on a specific topic.
10 Introduction
DAMA-SM-20-002 Revision History
3. Revision History
Month/Year Version Revised contents
11/ 2020 DAMA-SM-20-002 First edition
Introduction 11
DAMA-SM-20-002
Part 1
General Information
1. What is Inverter? ...................................................................................13
2. Inverter Basics ......................................................................................14
3. Names and Functions of Inverter Components.....................................15
4. Applicable Models .................................................................................16
12 Part 1 General Information

DAMA-SM-20-002 What is Inverter?
Chapter
1 Basics of Inverter Control
1. What is Inverter?
Maybe you have seen or heard the word “inverter” in various products such as inverter lights, inverter washing
machines, or inverter refrigerators.
The inverter is frequency converting equipment, indicating the technology to control voltage, current, and
frequency.
Inverter air conditioners can “save energy” since the inverter technology allows precise control of the compressor,
which plays a key role to cool or heat air, or the number of revolutions of the motor to drive fans. Non-inverter air
conditioners can only provide simple ON/OFF operation for temperature control, in other words, operation stops
when the set temperature is reached and starts when the temperature rises (or falls, in the case of heating).
Inverter air conditioners enable full-power operation until the set temperature is reached and then switching to
low-speed operation once it is reached, resulting in reduced power consumption compared to non-inverter air
conditioners.
7HPS
5DSLGFRROLQJ 6PDOOWHPS
GLíHUHQFH 6RPHZKDWKRW
&RPIRUWDEOH
6HW ,QYHUWHU
WHPS
1RQLQYHUWHU
7RRFROG
2SHUDWLRQVWDUWV7LPH
,QYHUWHUDLUFRQGLWLRQHUVKDYHDODUJH
QXPEHURIFRPSRQHQWVZKLFK
PDNHVVHUYLFHGLDJQRVLVGLîFXOW
7KHUHIRUHWKHLQYHUWHUGLDJQRVWLF
WHFKQLTXHLVFUXFLDO
Item Non-inverter air conditioner Inverter air conditioner
1. Time until the room temperature 1. Relatively takes time due to 1. Takes short time by increasing capacity
reaches the set temperature fixed capacity
2. Changes in temperature after 2. Large changes due to 2. Small changes due to operating capacity
the set temperature is reached operation ON/OFF responding to the load (comfortable)
3. Inrush current when compressor 3. 5-6 times of rated current 3. 1.5 times of rated current due to precise
starts up current control
4. Heating operation 4. Performance decreases 4. Increased rotation speed makes up for
characteristics at low outdoor air decreased performance
temperature
5. Defrost operation time 5. Relatively takes time due to 5. Operation at full capacity makes it short
fixed capacity
6. Apparatus configuration 6. Relatively simple
7. Service diagnosis 7. Relatively easy
General Information 13
Inverter Basics DAMA-SM-20-002
2. Inverter Basics
An inverter is a device to convert DC (direct current) into AC (alternating current).
For air conditioners, an inverter is a device to convert current from commercial AC power supply to AC having an
arbitrary frequency and voltage, including the converter function to convert AC into DC. The inverter freely varies the
rotation speed of the compressor motor.

$& '&
/RZIUHTXHQF\ +LJKIUHTXHQF\
6PDOOQXPEHURIUHYV /DUJHQXPEHURIUHYV

,QYHUWHUIUHHO\YDULHV
WKHURWDWLRQVSHHGRI
$& WKHPRWRU
<Block diagram of inverter>

&RPPHUFLDO$&
SRZHUVXSSO\ '&9ROWDJH
9DULDEOHYROWDJH
/
$& 1
3RZHU 9DULDEOHIUHTXHQF\
0RWRU
0RGXOH $&
'&
'%
−
&RQYHUWLQJ$& &RQYHUWLQJ'&
LQWR'& LQWR$&
&RQYHUWHU ,QYHUWHU
14 General Information
DAMA-SM-20-002 Names and Functions of Inverter Components
3. Names and Functions of Inverter Components

Names and functions of inverter components are as below.
<Schematic view of inverter main circuit configuration>
5HDFWRU 3RZHUPRGXOH ,30

8 9 :

6PRRWKLQJ
FDSDFLWRU 0RWRU
8−9− :−
&RPPHUFLDO$&
SRZHUVXSSO\

−
'LRGHPRGXOH &RQWURO
,QYHUWHU
FRQWUROOHU
Name Function
(1)Diode module Rectifies AC into DC
‫ڀ‬
(2)Smoothing capacitor Smooths out pulsating
current by charging and
discharging into
smoothed DC ‫ڀ‬
(3)Reactor Reduces pulsating
current
‫ڀ‬
(4)Power module (IPM) Chops DC at high speed
into sine-wave AC
‫ڀ‬
(5)Inverter controller Generates 1/0 digital
signals for converting DC
into AC from operation/ 8 2)) 21
frequency commands and
sends them out to IPM 9 2)) 21
: 2)) 21
Applicable Models DAMA-SM-20-002
4. Applicable Models
Nomenclature
Model Name and Power Supply
Indoor Unit Outdoor Unit Power Supply
FTXC20BV1B RXC20BV1B
1Phase, 220-240V, 50Hz
ATXC20BV1B ARXC20BV1B
16 General Information
DAMA-SM-20-002 Applicable Models
Nomenclature
Indoor Unit
Definition Description
F : Air-Cooled Split Indoor Unit, DAIKIN Brand

Unit Category
A : Air-Cooled Split Indoor Unit, DAIKIN Siesta Brand
Product Type T : Wall Mounted
System X : Inverter, Heatpump
Refrigerant & Grade C : R32 , Standard
Capacity Indication* 20 : 2.0 kW
Major Design Change B : B Series
Power Supply V1 : 1Phase / 220V-240V / 50Hz
Market B : Europe
Outdoor Unit
Definition Description
A : Air-Cooled Split Indoor Unit, DAIKIN Brand

Unit Category
AR : Air-Cooled Split Indoor Unit, DAIKIN Siesta Brand
System X : Inverter, Heatpump
Refrigerant & Grade C : R32 , Standard
Capacity Indication* 20 : 2.0 kW
Major Design Category B : B Series
Power Supply V1 : 1Phase / 220V-240V / 50Hz
Market B : Europe
Remark:
*Capacity value under Nomenclature is an indication.
Please refer to Engineering and Physical Data for exact capacity value.
DAMA-SM-20-002
Part 2
Specifications
1. Specification Data .................................................................................19
2. Functions...............................................................................................25
Part 2 Specifications 18
Specification Data DAMA-SM-20-002
1. Specification Data
INDOOR UNIT FTXC20B FTXC25B
MODEL RXC20B RXC25B
OUTDOOR UNIT
Cooling Heating Cooling Heating
kW 2.00 (1.30 ~ 3.00) 2.50 (1.30 ~ 4.00) 2.56 (1.30 ~ 3.00) 2.84 (1.30 ~ 4.00)
Rated Capacity (Min. ~ Max.)
Btu/h 6800 (4400 ~ 10200)8500 (4400 ~ 13600) 8700 (4400 ~ 10200) 9700 (4400 ~ 13600)
Rated Running Current (Min. ~ Max.) A 3.43 (1.86 ~ 5.13) 3.16 (1.74 ~ 5.95) 3.47 (1.86 ~ 5.13) 3.45 (1.74 ~ 5.95)
Rated Power Consumption (Min. ~ Max.) W 595 (300 ~ 1150) 670 (275 ~ 1350) 765 (300 ~ 1150) 750 (275 ~ 1350)
EER W/W 3.36 N/A 3.35 N/A
SEER 6.89 N/A 6.84 N/A
COP W/W N/A 3.73 N/A 3.79
SCOP (Average Climate) N/A 4.40 N/A 4.45
SCOP (Warm Climate) N/A 5.78 N/A 5.81
Power Factor (Rated) 0.754 0.922 0.959 0.945
Piping Liquid mm 6.4
Connections Gas mm 9.5
Type R32
Refrigerant
Charge kg 0.55
Max. Interunit Piping Length m 20
Max. Interunit Height Difference m 15
Front Panel Colour WHITE
Turbo CFM 410
High CFM 380
Airflow Rate Medium CFM 310
Low CFM 230
Quiet CFM 190
Sound Pressure Level (H/M/L/Q) dBA 38/33/26/20
Type CROSS FLOW
Fan
Drive DIRECT
Type DIRECT CURRENT
Motor Output W 38
Fan Motor
Running Current (Rated) A 0.14
Power Consumption (Rated) W 16
Air Direction Control UP, DOWN, LEFT, RIGHT
Air Filter CATECHIN
Dimensions (H X W X D) mm 288 X 785 X 250
Packaged Dimensions (H X W X D) mm 327 X 830 X 363
Weight kg 9.0
Condensate Drain Size mm 19.05
OUTDOOR UNIT RXC20B RXC25B
Casing Colour IVORY WHITE
Airflow Rate CFM 930
Sound Pressure Level dBA 45
Type PROPELLER
Fan
Drive DIRECT
Type DIRECT CURRENT
Index of protection (IP) 24
Insulation Grade E
Fan Motor Running Current (Rated) A 0.28
Motor Output W 26
Poles 8
Type HERMETIC SWING
Oil type DAPHNE FW68DA
Compressor Oil amount cm3 375
Running Current (Rated) A N/A
Power Consumption (Rated) W N/A
Heat Exchanger Type FIN TUBE
Weight kg 24
Document No. (Set) 3D117996 C
1) ALL UNITS ARE BEING TESTED AND COMPLY TO ISO 5151 (NON-DUCTED UNIT) OR ISO 13253 (DUCTED UNIT).
2) ALL SPECIFICATIONS ARE SUBJECTED TO CHANGE BY THE MANUFACTURER WITHOUT PRIOR NOTICE.
COOLING HEATING
INDOOR: 27°CDB / 19°CWB INDOOR: 20°CDB
OUTDOOR: 35°CDB OUTDOOR: 7°CDB / 6°CWB
19 Specifications
DAMA-SM-20-002 Specification Data

MODEL RXC35B RXC50B
OUTDOOR UNIT
kW 3.50 (1.30 ~ 4.00) 4.00 (1.30 ~ 4.80) 5.10 (1.37 ~ 6.20) 5.62 (1.36 ~ 6.60)
Rated Capacity (Min. ~ Max.) 11900 13600 17400 19200
Btu/h
(4400 ~ 13600) (4400 ~ 16400) (4700 ~ 21200) (4600 ~ 22500)
Rated Power Consumption (Min. ~ Max.) W 1045 (315 - 1740) 1070 (275 - 1570) 1550 (295 - 2110) 1515 (270 - 1850)
EER W/W 3.35 N/A 3.29 N/A
SEER 6.87 N/A 6.45 N/A
COP W/W N/A 3.74 N/A 3.71
Connection Gas mm 9.5 12.7
Type R32
Refrigerant
Charge kg 0.75 1.00
Max. Interunit Piping Length m 20 30
Max. Interunit Height Difference m 15 20
Turbo CFM 400 450
High CFM 380 430
Airflow Rate Medium CFM 320 360
Low CFM 230 290
Quiet CFM 190 260
Sound Pressure Level (H/M/L/Q) dBA 39/34/26/21 45/39/33/29
Type CROSS FLOW
Fan
Drive DIRECT
Type DIRECT CURRENT
Motor Output W 38
Fan Motor
Running Current (Rated) A 0.15 0.19
Power Consumption (Rated) W 18 24
Air Filter CATECHIN
Weight kg 9.5
Airflow Rate High CFM 840 1310
Sound Pressure Level dBA 46 51
Type PROPELLER
Fan
Drive DIRECT
Type DIRECT CURRENT
Index of protection (IP) 24 23
Insulation Grade E
Fan Motor Running Current (Rated) A 0.32 0.38 0.49
Power Consumption (Rated) W 33 46 63
Motor Output W 26 61
Poles 8
Type HERMETIC SWING
Oil Type DAPHNE FW68DA
Compressor Oil amount cm3 375 650
Dimensions (H X W X D) mm 550 X 658 X 273 615 X 845 X 300
Packaged Dimensions (H X W X D) mm 610 X 781 X 363 679 X 992 X 414
Weight kg 26 39
1) ALL UNITS ARE BEING TESTED AND COMPLY TO ISO 5151 (NON-DUCTED UNIT) OR ISO 13253 (DUCTED UNIT)
COOLING HEATING
Specifications 20

MODEL RXC60B RXC71B
OUTDOOR UNIT
kW 6.23 (1.80 ~ 7.00) 6.40 (1.48 ~ 8.00) 7.10 (2.30 ~ 7.30) 8.00 (2.30 ~ 9.00)
Btu/h
(6100 ~ 23900) (5000 ~ 27300) (7800 ~ 24900) (7800 ~ 30700)
EER W/W 3.30 N/A 2.98 N/A
SEER 6.40 N/A 5.30 N/A
COP W/W N/A 3.81 N/A 3.25
Connection Gas mm 12.7
Type R32
Refrigerant
Charge kg 1.10 1.15
Turbo CFM 770
High CFM 720
Low CFM 480
Quiet CFM 360
Type CROSS FLOW
Fan
Drive DIRECT
Type DIRECT CURRENT
Motor Output W 38
Fan Motor
Air Filter CATECHIN
Weight kg 13.0
Type PROPELLER
Fan
Drive DIRECT
Type DIRECT CURRENT
Insulation Grade E
Fan Motor Running Current (Rated) A 0.62 0.97
Poles 8
Type HERMETIC SWING
Weight kg 39 45
COOLING HEATING
21 Specifications
INDOOR UNIT ATXC20B ATXC25B

MODEL ARXC20B ARXC25B
OUTDOOR UNIT
kW 2.00 (1.30 ~ 3.00) 2.50 (1.30 ~ 4.00) 2.56 (1.30 ~ 3.00) 2.84 (1.30 ~ 4.00)
Btu/h
(4400 ~ 10200) (4400 ~ 13600) (4400 ~ 10200) (4400 ~ 13600)
EER W/W 3.30 N/A 3.30 N/A
SEER 6.81 N/A 6.74 N/A
COP W/W N/A 3.73 N/A 3.76
Type R32
Refrigerant
Charge kg 0.55
Turbo CFM 410
High CFM 380
Low CFM 230
Quiet CFM 190
Type CROSS FLOW
Fan
Drive DIRECT
Type DIRECT CURRENT
Motor Output W 38
Fan Motor
Air Filter CATECHIN
Weight kg 9.0
OUTDOOR UNIT ARXC20B ARXC25B
Airflow Rate High CFM 930
Type PROPELLER
Fan
Drive DIRECT
Type DIRECT CURRENT
Insulation Grade E
Fan Motor Running Current (Rated) A 0.28
Motor Output W 26
Poles 8
Type HERMETIC SWING
Weight kg 24
Document No. (Set) 3D118001 B
COOLING HEATING
Specifications 22

OUTDOOR UNIT
kW 3.50 (1.30 ~ 4.00) 4.00 (1.30 ~ 4.80) 5.10 (1.37 ~ 6.20) 5.62 (1.36 ~ 6.60)
Btu/h
(4400 ~ 13600) (4400 ~ 16400) (4700 ~ 21200) (4600 ~ 22500)
Rated Power Consumption (Min. ~ Max.) W 1060 (315 - 1740) 1075 (275 - 1570)) 1570 (295 - 2110) 1515 (270 - 1850)
EER W/W 3.30 N/A 3.25 N/A
SEER 6.78 N/A 6.40 N/A
COP W/W N/A 3.72 N/A 3.71
Connection Gas mm 9.5 12.7
Type R32
Refrigerant
Charge kg 0.75 1.00
Max. Interunit Piping Length m 20 30
Max. Interunit Height Difference m 15 20
Turbo CFM 400 450
High CFM 380 430
Airflow Rate Medium CFM 320 360
Low CFM 230 290
Quiet CFM 190 260
Sound Pressure Level (H/M/L/Q) dBA 39/34/26/21 45/39/33/29
Type CROSS FLOW
Fan
Drive DIRECT
Type DIRECT CURRENT
Motor Output W 38
Fan Motor
Running Current (Rated) A 0.15 0.19
Air Filter CATECHIN
Weight kg 9.5
Sound Pressure Level dBA 46 51
Type PROPELLER
Fan
Drive DIRECT
Type DIRECT CURRENT
Index of protection (IP) 24 23
Insulation Grade E
Fan Motor Running Current (Rated) A 0.32 0.38 0.49
Power Consumption (Rated) W 33 46 63
Poles 8
Type HERMETIC SWING
Compressor Oil amount cm3 375 650
Weight kg 26 39
COOLING HEATING
23 Specifications

OUTDOOR UNIT
kW 6.23 (1.80 ~ 7.00) 6.40 (1.48 ~ 8.00) 7.10 (2.30 ~ 7.30) 8.00 (2.30 ~ 9.00)
Btu/h
(6100 ~ 23900) (5000 ~ 27300) (7800 ~ 24900) (7800 ~ 30700)
Rated Running Current (Min. ~ Max.) A 8.40(1.86 ~ 8.96) 7.58 (1.61 ~ 10.27) 10.60 (2.17 ~ 11.10) 10.90 (2.48 ~ 12.00)
EER W/W 3.25 N/A 2.95 N/A
SEER 6.38 N/A 5.25 N/A
COP W/W N/A 3.71 N/A 3.21
Type R32
Refrigerant
Charge kg 1.10 1.15
Turbo CFM 770
High CFM 720
Low CFM 480
Quiet CFM 360
Type CROSS FLOW
Fan
Drive DIRECT
Type DIRECT CURRENT
Motor Output W 38
Fan Motor
Air Filter CATECHIN
Weight kg 13.0
Type PROPELLER
Fan
Drive DIRECT
Type DIRECT CURRENT
Insulation Grade E
Fan Motor Running Current (Rated) A 0.62 0.97
Poles 8
Type HERMETIC SWING
Weight kg 39 45
COOLING HEATING
Specifications 24
Functions DAMA-SM-20-002
2. Functions
FTXC20/25/35B
RXC20/25/35B
FTXC60/71B
RXC60/71B
FTXC50B
RXC50B
Category Functions
Inverter   
Innovaire Technology — — —
Operation Limit for Cooling (°CDB)(O/D) 10 - 46 -10 - 46 -10 - 46
Basic Function
Operation Limit for Cooling (°FDB)(O/D) 50 - 114.8 14 - 114.8 14 - 114.8
Operation Limit for Heating (°CWB)(O/D) -15 - 18 -15 - 18 -15 - 18
Operation Limit for Heating (°FWB)(O/D) 5 - 64.4 5 - 64.4 5 - 64.4
Scroll Compressor — — —
Compressor Swing Compressor   
Rotary Compressor — — —
Power-airflow flap   —
Power-airflow dual flaps — — 
Power-airflow diffuser — — —
Wide angle louvers   
Comfortable Airflow
Vertical Auto-Swing (Up and Down)   
Horizontal Auto-Swing (Right and Left) — — —
3D Airflow — — —
Breeze Airflow — — —
Auto Fan Speed   
Indoor/Outdoor Unit Quiet Operation   
Comfort Control
Intelligent Eye Operation — — —
Automatic Defrosting   
Automatic Operation   
Operation Programme Dry Operation   
Fan Only   
Powerful Operation (Non Inverter) — — —
Inverter Powerful Operation   
Energy Saving Function   
Sleep Mode   
Lifestyle Convenience
Indoor Unit On/Off button   
Remote Controller with Backlight   
Signal receiving sign (Remote Controller)   
Set Temperature Display (Remote Controller)   
Saranet Filter — — —
Catechin Filter / Green Tea Filter   
Titanium Apatite Air-Purifying Filter   
Health & Clean PM 2.5 Filter — — —
Streamer — — —
Plasma — — —
Wipe clean flat panel   
Weekly Timer Operation — — —
Timer
24-hour ON/OFF Timer   
Auto Restart (after Power Failure)   
Worry Free
Self-Diagnosis (Handset) Display   
(Reliability & Durability)
Anticorrosion Treatment of Outdoor Heat Exchanger   
Pre charged piping length 7.5m 7.5m 7.5m
Flexibility
Either Side Drain (Right or Left)   
BAG Connectivity   
Remote Control WIFI Connectivity   
DIII-NET Connectivity   
Wireless (BRC52B66)   
Remote Controller
Wired * * *
Note:  : Available
— : Not available
* : Optional (Refer to DAMA Spare Part Team for more details on optional items.)
25 Specifications
DAMA-SM-20-002 Functions
ARXC20/25/35B
ATXC20/25/35B
ARXC60/71B
ATXC60/71B
ARXC50B
ATXC50B
Category Functions
Inverter   
Innovaire Technology — — —
Operation Limit for Cooling (°CDB)(O/D) 10 - 46 -10 - 46 -10 - 46
Basic Function
Operation Limit for Cooling (°FDB)(O/D) 50 - 114.8 14 - 114.8 14 - 114.8
Operation Limit for Heating (°CWB)(O/D) -15 - 18 -15 - 18 -15 - 18
Operation Limit for Heating (°FWB)(O/D) 5 - 64.4 5 - 64.4 5 - 64.4
Scroll Compressor — — —
Compressor Swing Compressor   
Rotary Compressor — — —
Power-airflow flap   —
Power-airflow dual flaps — — 
Power-airflow diffuser — — —
Wide angle louvers   
Comfortable Airflow
Vertical Auto-Swing (Up and Down)   
Horizontal Auto-Swing (Right and Left) — — —
3D Airflow — — —
Breeze Airflow — — —
Auto Fan Speed   
Indoor/Outdoor Unit Quiet Operation   
Comfort Control
Intelligent Eye Operation — — —
Automatic Defrosting   
Automatic Operation   
Operation Programme Dry Operation   
Fan Only   
Powerful Operation (Non Inverter) — — —
Inverter Powerful Operation   
Energy Saving Function   
Sleep Mode   
Lifestyle Convenience
Indoor Unit On/Off button   
Remote Controller with Backlight   
Signal receiving sign (Remote Controller)   
Set Temperature Display (Remote Controller)   
Saranet Filter — — —
Catechin Filter / Green Tea Filter   
Titanium Apatite Air-Purifying Filter   
Health & Clean PM 2.5 Filter — — —
Streamer — — —
Plasma — — —
Wipe clean flat panel   
Weekly Timer Operation — — —
Timer
24-hour ON/OFF Timer   
Auto Restart (after Power Failure)   
Worry Free
Self-Diagnosis (Handset) Display   
(Reliability & Durability)
Anticorrosion Treatment of Outdoor Heat Exchanger   
Pre charged piping length 7.5m 7.5m 7.5m
Flexibility
Either Side Drain (Right or Left)   
BAG Connectivity   
Remote Control WIFI Connectivity   
DIII-NET Connectivity   
Wireless (BRC52B66)   
Remote Controller
Wired * * *
Note:  : Available
— : Not available
* : Optional (Refer to DAMA Spare Part Team for more details on optional items.)
Specifications 26
DAMA-SM-20-002
Part 3
Functions and Control
1. Main Functions......................................................................................28
1.1 Temperature Control ..............................................................................28
1.3 Airflow Direction Control.........................................................................30
1.4 Fan Speed Control for Indoor Unit .........................................................30
1.5 Dry Mode................................................................................................31
1.6 Automatic Operation...............................................................................32
1.7 Thermostat Control.................................................................................33
1.8 ECO+ Operation ....................................................................................34
1.9 Sleep Mode ............................................................................................35
1.10 POWERFUL Operation ..........................................................................35
1.11 Other Functions......................................................................................36
2. Thermistor Functions ............................................................................37
3. Control Specification .............................................................................38
3.1 Mode Hierarchy ......................................................................................38
3.3 Standby Electricity Saving (Suspend Function) .....................................41
3.4 Controls at Mode Changing/Start-up......................................................41
3.6 Input Current Control..............................................................................44
3.8 Heating Peak-cut Control .......................................................................46
3.9 Outdoor Fan Control...............................................................................47
3.10 Liquid Compression Protection Function................................................48
3.11 Defrost Control .......................................................................................48
3.12 Electronic Expansion Valve Control .......................................................49
3.13 Malfunctions ...........................................................................................53
Part 3 Functions and Control 27

Main Functions DAMA-SM-20-002
1. Main Functions
1.1 Temperature Control
Definitions of The definitions of temperatures are classified as following.
Temperatures
 Room temperature: temperature of lower part of the room
 Set temperature: temperature set by remote controller
 Room thermistor temperature: temperature detected by room temperature thermistor
 Target temperature: temperature determined by microcomputer
Target temperature
Room thermistor temperature
Set temperature
Room temperature
Temperature The temperature of the room is detected by the room temperature thermistor. However, there is
Control a difference between the temperature detected by room temperature thermistor and the
temperature of lower part of the room, depending on the type of the indoor unit or installation
condition. In practice, the temperature control is done by the target temperature appropriately
adjusted for the indoor unit and the temperature detected by room temperature thermistor.
1.2 Frequency Control

Control The frequency of the compressor is controlled by the following 2 parameters:
Parameters  The load condition of the operating indoor unit
 The difference between the room thermistor temperature and the target temperature
The target frequency is adapted by additional parameters in the following cases:

 Frequency restrictions
 Initial settings
 Forced cooling operation
Inverter Principle To regulate the capacity, a frequency control is needed. The inverter makes it possible to
control the rotation speed of the compressor. The following explain the inverter principle:
Phase 1
The supplied AC power source is converted into the DC power source for the present.
Phase 2
The DC power source is reconverted into the three phase AC power source with variable
frequency.
 When the frequency increases, the rotation speed of the compressor increases resulting in
an increase of refrigerant circulation. This leads to a larger amount of heat exchange per
unit.
 When the frequency decreases, the rotation speed of the compressor decreases resulting in
a decrease of refrigerant circulation. This leads to a smaller amount of heat exchange per
unit.
28 Functions and Control

DAMA-SM-20-002 Main Functions
The following drawing shows a schematic view of the inverter principle:
Refrigerant circulation rate (high)
high speed
Amount of heat Amount of heat
exchanged air (large) high f exchanged air (large)
power
power
DC
AC
Amount of heat low f Amount of heat
exchanged air (small) exchanged air (small)
low speed
freq= 50 Hz capacity=
constant 60 Hz freq=variable variable
Refrigerant circulation rate (low)
Inverter Features The inverter provides the following features:

 The regulating capacity can be changed according to the changes in the outdoor
temperature and cooling load.
 Quick cooling
The rotation speed of the compressor is increased when starting the cooling.
This enables to reach the set temperature quickly.
 Comfortable air conditioning
A fine adjustment is integrated to keep the room temperature constant.
 Energy saving cooling
Once the set temperature is reached, the energy saving operation enables to maintain the
room temperature at low power.
Frequency Limits The following functions regulate the minimum and maximum frequency:
 Compressor protection function. Refer to page 41.
 Discharge pipe temperature control. Refer to page 43.
 Input current control. Refer to page 44.
 Freeze-up protection control. Refer to page 45.
Forced Cooling Refer to page 107 for details.

Operation
Functions and Control 29

1.3 Airflow Direction Control

Power-Airflow The large flap sends a large volume of air downward to the floor and provides an optimum
Flap control in cooling and dry operation.
Cooling/Dry
During cooling or dry operation, the flap retracts into the indoor unit. Then, cool air can be blown
far and distributed all over the room.
Wide-Angle The louvers, made of elastic synthetic resin, provide a wide range of airflow that guarantees
Louvers comfortable air distribution.
Auto-Swing The followings explain the auto-swing process for cooling, dry and fan:
Series Cooling / Dry / Fan (A - B) Heating (A - B)

(A)FTXC Series 40 - 65 45 - 90
0°
A°
B°
1.4 Fan Speed Control for Indoor Unit

(A)FTXC Outline Phase control and fan speed control contains 5 steps: SL, L, M, H, SH.
The airflow rate can be automatically controlled depending on the difference between the room
thermistor temperature and the set temperature.
(A)FTXC Outline Phase control and fan speed control contains 5 steps: SL, L, M, H, SH.
On heating mode, the indoor fan speed will be regulated according to the indoor heat exchanger
temperature and the difference between the room temperature and the required set
temperature.
Automatic Fan In automatic fan speed operation, the step SL, & SH is not available.
Speed Control
Step Cooling Heating
L
M
H
= The airflow rate is automatically controlled within this range when FAN setting button is
set to automatic.
Series SL L M H SH
(A)FTXC20/25 190 230 310 380 410
(A)FTXC35 190 230 320 380 400
(A)FTXC50 260 290 360 430 450
(A)FTXC60/71 360 480 560 720 770

Cooling
The following drawings explain the principle of fan speed control for cooling.
Room thermistor temperature – set temperature
Fan speed
+2°C
H
+1.5°C
+1.5°C
L
+0.5°C
Heating
The following drawings explain the principle of fan speed control for heating.
On heating mode, the indoor fan speed will be regulated according to the heat exchanger
temperature and the difference between the room temperature and the required target
temperature.
Fan speed
+3°C
H
+2.5°C
+0.5°C 1°C
0°C L
1.5 Dry Mode

Outline Program dry operation removes humidity. Since the microcomputer controls the airflow rate, the
FAN setting buttons are inoperable.
Details The microcomputer automatically sets the airflow rate. The difference between the room
thermister temperature and the set temperature is divided into zones. Then, the unit operates in
an appropriate capacity for each zone to maintain the temperature and humidity at a
comfortable level.Zone B continues to stay for 120 seconds before the unit will turn to
thermostat ON.
X
Zone C - Thermostat ON
Zone B Zone B
Y
+0.5°C (0.9°F)
Zone A - Thermostat OFF
Target temperature X Thermostat OFF point Y Thermostat ON point Y

Room thermistor temperature Room thermistor temperature
Setting temperature
- X = (< -1.5° C) or (< -2.7° F) - X = (≥ -1.5° C) or (≥ 2.7° F)

1.6 Automatic Operation

Automatic Cooling / Heating Function (Heat Pump Only)
When the AUTO mode is selected with the remote controller, the microcomputer automatically
determines the operation mode from cooling and heating according to the room temperature
and setting temperature at the time of the operation startup, and automatically operates in that
mode.
The unit automatically switches the operation mode to cooling or heating to maintain the room
temperature at the main unit setting temperature.
Details 1. Remote controller setting temperature is set as automatic cooling / heating setting
Explanation of temperature 16°C to 30°C.
the Function 2. Main unit setting temperature equals remote controller setting temperature.
3. Operation ON / OFF point and mode switching point are as follows.
a Heating  Cooling switching point:
Room temperature ≥ Main unit setting temperature +2.5 deg.
b Cooling  Heating switching point:
Room temperature < Main unit setting temperature -2.5 deg.
c Thermostat ON / OFF point is the same as the ON / OFF point of cooling or heating
operation.
4. During initial operation
Room temperature ≥ Remote controller setting temperature: Cooling operation
Room temperature < Remote controller setting temperature: Heating operation
Cooling Operation
Set point +2.5°C
Set point +1.5°C

Set point -1.5°C
=Thermostat OFF
=Thermostat OFF
Set point -2.5°C

Heating Operation
Ex : When the set temperature is 25°C,

Scenario 1 Thermostat OFF  23.5°C. If room temperature continues to drop to 22.5°C :
 Switch from Cooling Operation to Heating Operation
Scenario 2 Room temperature maintains at 25°C :
 No Switch in Operation mode
Scenario 3 Thermostat OFF  26.5°C. If room temperature continues to increase to 27.5°C
 Switch from Heating Operation to Cooling Operation

1.7 Thermostat Control

Outline Thermostat control is based on the difference between the room thermistor temperature and the
set temperature.
Details Thermostat OFF Conditions

 The temperature difference is in the zone A.
Thermostat ON Conditions
 The temperature difference returns to the zone C after being in the zone A.
 The operation turns on in any zones except A.
 The monitoring time has passed while the temperature difference is in the zone B.
(Cooling/Dry/Heating: 2 minutes)
Cooling/Dry
ON
Cooling : –0.5°C
Zone C Dry : –0.5°C
–1.0°C
Zone B
Cooling/Dry : –1.5°C
Zone A
OFF
Applicable to (A)FTXC series only.
Heating
Room temperature – set temperature
OFF
A
1.5°C
B
C
0.5°C
ON

1.8 ECO+ Operation

Outline ECO+ operation reduces the maximum operating power input and adjust the target temperature
setting. This operation is particularly convenient for energy-saving. It is also a major bonus
when breaker capacity does not allow the use of multiple electrical devices and air conditioners.
It can be easily activated by pressing ECO+ button on the wireless remote controller.
Details
Cool mode
Unit runs at 24˚C (75˚F)
24
User set
User set temperature < temp
24°C
ECO+ activated
Unit runs at (user set temperature + 1°C/2°F)
(User set temp + 1°C/2°F)
User
set temp
User set temperature ≥
24°C 24
ECO+ activated
Applicable for (A)FTXC series only.

Heat mode
Unit runs at 20°C (68°F)
User set
User set temperature > temp
20°C 20
ECO+ activated
Unit runs at (user set temperature - 1°C/2°F)
20
User set
User set temperature ≤ temp (User set temp - 1°C/2°F)
20°C
ECO+ activated

1.9 Sleep Mode

Outline SLEEP Mode can be activated through the remote controller to keep the thermal comfort while
sleeping.
Details SLEEP Mode continues operation at the target temperature for the first hour, then automatically
raises the target temperature slightly in case of cooling, or lowers it slightly in case of heating.
This prevents excessive cooling in summer and excessive heating in winter to ensure
comfortable sleeping conditions and also saves electricity.
ON signal of sleep operation OFF signal of sleep operation

ON signal of sleep operation+operation ON signal operation OFF signal
run
sleep operation
1hr 1hr
(no offset on target
temperature)
target temperature
<COOL or DRY> (shift 0.5°C/0.9°F) (shift 1.0°C/1.8°F)
(shift 1.0°C/1.8°F) (shift 2.0°C/3.6°F)

target temperature
<HEAT>
1.10 POWERFUL Operation

Outline In order to exploit the cooling capacity to full extent, the air conditioner can be operated by
increasing the indoor fan rotating speed and the compressor frequency.
Details When POWERFUL button is pressed, the fan speed and target temperature are converted to
the following states for 20 minutes.
Operation mode Fan speed Target temperature
COOL H tap + A rpm Setting temperature -4°C
HEAT H tap + A rpm Setting temperature +6°C
H = high fan
A = refer table below
Mode Model 20/25 35/50 60/71
COOL/HEAT (A)FTXC 70 50 70
Note POWERFUL operation cannot be used together with ECO+ operation.

1.11 Other Functions

1.11.1 Signal Receiving Sign
When the indoor unit receives a signal from the remote controller, the unit emits a signal
receiving sound.
1.11.2 Indoor Unit ON/OFF Switch

Indoor unit ON/OFF switch is provided on the display of the unit.
 Press ON/OFF switch once to start operation. Press once again to stop it.
 ON/OFF switch is useful when the remote controller is missing or the battery has run out.
 The operation mode refers to the following table.
Operation mode Temperature setting Airflow rate
(A)FTXC series AUTO 25°C Automatic
ON/OFF
switch
Forced Cooling Operation

Forced cooling operation can be started by pressing ON/OFF switch for 5 ~ 9 seconds while the
unit is not operating.
Refer to page 107 for details.
Note Forced cooling operation will not be started if the ON/OFF switch is pressed for 10 seconds or
more.
1.11.3 Auto-restart Function

If a power failure (even a momentary one) occurs during the operation, the operation restarts
automatically in the same conditions as before when the power supply is restored to the
conditions prior to the power failure.
Note It takes 3 minutes to restart the operation because 3-minute standby function is activated.
1.11.4 Hot-start function

In order to prevent the cold air blast that normally comes when heating is started, the
temperature of the heat exchanger of the indoor is detected, and either the airflow is stopped or
is made very weak thereby carrying out comfortable heating of the room.
Note *The cold air blast is also prevented using a similar control when the defrosting operation is
started or when the thermostat gets turned ON.

DAMA-SM-20-002 Thermistor Functions
2. Thermistor Functions
(A)FTXC series only
(2) Outdoor Heat
(5) Room
Exchanger
Temperature
(3) Outdoor Thermistor
Expansion valve Thermistor
Temperature
Thermistor
(4) Indoor Heat

Exchanger
Thermistor
Four way valve
(1) Discharge Pipe

Temperature Compressor
(1) Discharge  The discharge pipe thermistor is used for controlling discharge pipe temperature. If the
Pipe Thermistor discharge pipe temperature (used in place of the inner temperature of the compressor) rises
abnormally, the operating frequency becomes lower or the operation halts.
 The discharge pipe thermistor is used for detecting disconnection of the discharge pipe
thermistor.
(2) Outdoor Heat  The outdoor heat exchanger thermistor is used for controlling the target discharge pipe
Exchanger temperature. The system sets the target discharge pipe temperature according to the
Thermistor outdoor and indoor heat exchanger temperature, and controls the electronic expansion valve
opening so that the target discharge pipe temperature can be obtained.
 In cooling operation, the outdoor heat exchanger thermistor is used for detecting the
disconnection of the discharge pipe thermistor. When the discharge pipe temperature drops
below the outdoor heat exchanger temperature by more than a certain value, the discharge
pipe thermistor is judged as disconnected.
 In cooling operation, the outdoor heat exchanger thermistor is used for high pressure
protection.
(3) Outdoor  The outdoor temperature thermistor detects the outdoor air temperature and is used for
Temperature refrigerant shortage detection, input current control, outdoor fan control, liquid compression
Thermistor protection function, and so on.
(4) Indoor Heat  The indoor heat exchanger thermistor is used for controlling the target discharge pipe
Exchanger temperature. The system sets the target discharge pipe temperature according to the
Thermistor outdoor and indoor heat exchanger temperature, and controls the electronic expansion valve
opening so that the target discharge pipe temperature can be obtained.
 In cooling operation, the indoor heat exchanger thermistor is used for freeze-up protection
control. If the indoor heat exchanger temperature drops abnormally, the operating frequency
becomes lower or the operation halts.
 During heating, the indoor heat exchanger thermistor is used for detecting disconnection of
the discharge pipe thermistor.
When the discharge pipe temperature becomes lower than the indoor heat exchanger
temperature, the discharge pipe thermistor is judged as disconnected.
The indoor heat exchanger thermistor is also used for preventing abnormal high pressure.
(5) Room  The room temperature thermistor detects the room air temperature and is used for
Temperature controlling the room air temperature.
Thermistor

Control Specification DAMA-SM-20-002
3. Control Specification
3.1 Mode Hierarchy
Outline The air conditioner control has normal operation mode, forced operation mode, and power
transistor test mode for installation and servicing.
Details There are following modes; Fan, Cooling (includes drying), Stop.
Air conditioner control mode

Forced operation mode
Forced cooling operation (for pump down operation)

Power transistor test mode
Normal operation mode
Fan
Cooling (includes drying)
Stop (indoor unit: OFF)

Discharging from capacitor
Stop
There are following modes; Cooling (includes drying), Heating (includes defrosting), Stop.
Air conditioner control mode

Forced operating mode
Forced cooling (for Pump Down Operation)
Normal operating mode
Cooling
Heating
Defrosting
Stop mode (except for cooling/heating modes by indoor command)
Discharging from capacitor
Stop
Note Unless specified otherwise, dry operation command is regarded as cooling operation.

DAMA-SM-20-002 Control Specification
3.2 Frequency Control

Outline The compressor frequency is determined according to the difference between the room
thermistor temperature and the target temperature.
When the shift of the frequency is less than zero (∆F<0) by PI control,
the target frequency is used as the command frequency.
Dropping function
Input current control, etc.
Upper limit frequency Upper limit function

FMAX Compressor protection function
Command frequency Limit frequency Skip control Target frequency
Initial frequency Lower limit function

PI control Lower limit frequency
FMIN Four way valve operating compensation, etc*
Defrost control*
*Only applicable for heat-pump model

Details For Cooling Only model:
1. Determine command frequency
Command frequency is determined in the following order of priority.
(1) Forced cooling
(2) Indoor frequency command
2. Determine upper limit frequency

The minimum value is set as the upper limit frequency among the frequency upper limits of
the following functions:
Compressor protection, input current, discharge pipe temperature, freeze-up protection.
3. Determine lower limit frequency

The maximum value is set as the lower limit frequency among the frequency lower limits of
the following function:
Pressure difference upkeep.
4. Determine prohibited frequency

There is a certain prohibited frequency such as a power supply frequency.
For Heat-pump model:

1. Determine command frequency
 Command frequency will be determined in the following order of priority.
1.1 Limiting frequency by drooping function
 Input current, discharge pipes, peak cutting, freeze-up protection, dew prevention, fin
thermistor temperature.
1.2 Limiting defrost control time
1.3 Forced cooling
1.4 Indoor frequency command
2. Determine upper limit frequency

 Set a minimum value as an upper limit frequency among the frequency upper limits of the
following functions:
Compressor protection, input current, discharge pipes, peak cutting, freeze-up protection,
defrost.
3. Determine lower limit frequency

 Set a maximum value as an lower limit frequency among the frequency lower limits of the
following functions:
Four way valve operating compensation, draft prevention, pressure difference upkeep.
4. Determine prohibited frequency

 There is a certain prohibited frequency such as a power supply frequency.

Initial Frequency When starting the compressor, the frequency is initialized according to the ΔD value of the
indoor unit.
ΔD signal: Indoor frequency command

The difference between the room thermistor temperature and the target temperature is taken as
the ΔD value and is used for ΔD signal of frequency command.
In Cooling Mode In Heating Mode In Dry Mode

Temperature ΔD signal
Temperature
ΔD signal
Temperature
ΔD signal
difference difference difference
-1.5 0 -1.5 0 -1.5 0
-1 1 -1.0 1 -1 1
-0.5 2 -0.5 2 -0.5 2
0 3 0.0 3 0 3
0.5 4 0.5 4 0.5 4
1 5 1.0 5 1 5
1.5 6 1.5 6 1.5 6
2 7 2.0 7 2 7
2.5 2.5 8 2.5 8
8
3 3.0
3.5 9
4.0
PI Control 1. P control
ΔD value is calculated in each sampling time (20 seconds), and the frequency is adjusted
according to its difference from the frequency previously calculated.
2. I control
If the operating frequency does not change for more than a certain fixed time, the frequency
is adjusted according to ΔD value.
When ΔD is low, the frequency is lowered.
When ΔD is high, the frequency is increased.
3. Frequency control when other controls are functioning

 When frequency is dropping:
Frequency control is carried out only when the frequency drops.
 For controlling lower limit:
Frequency control is carried out only when the frequency rises.
4. Upper and lower limit of frequency by PI control

The frequency upper and lower limits are set according to the command of the indoor unit.
When the indoor unit quiet operation command comes from the indoor unit, the upper limit
frequency is lower than the usual setting.

3.3 Standby Electricity Saving (Suspend Function)

Outline This function is to save standby electricity consumption while the air conditioner is not in operation
by partially separating the electrical circuit of indoor and outdoor units from the power source.
Details  Standby electricity saving function can be activated/deactivated from the service mode of
the remote controller.
 When standby electricity saving is ON, the system enters suspend state if both indoor and
outdoor units are not in operation.
 The system will not go into suspend state when some voltage is applied to the outdoor unit
for protection purpose even if the indoor unit is not in operation.
 In suspend state, power supply to the outdoor unit is halted and there is no communication
between the indoor unit and the outdoor unit.
Also the service monitor LED (LED A) lights off.
 To return from the suspend state, start fan or other operation to turn on the indoor unit.
3.4 Controls at Mode Changing/Start-up

3.4.1 3-Minute Standby
Turning on the compressor is prohibited for 3 minutes after turning off.
3.4.2 Compressor Protection Function

When turning the compressor from OFF to ON, the upper limit of frequency is set as follows.
(Hz)
Frequency
112Hz
90Hz
72Hz
54Hz
40Hz
(sec.)
Time
RXC20/25/35 180 420 180 120 1
(Hz)
Frequency
98Hz
85Hz
70Hz
55Hz
(sec.)
Time
RXC50/60/71 120 200 470 0 60

3.4.3 Four Way Valve Switching

Outline Heat Pump Only
During the heating operation current must be conducted and during cooling and defrosting
current must not be conducted. In order to eliminate the switching sound (as the four way valve
coil switches from ON to OFF) when the heating is stopped, the delay switch of the four way
valve must be carried out after the operation stopped.
Details The OFF delay of four way valve

Energize the coil for 160 sec after unit operation is stopped.
3.4.4 Four Way Valve Operation Compensation

At the beginning of the operation as the four way valve is switched, acquire the differential
pressure required for activating the four way valve by having output the operating frequency,
which is more than a certain fixed frequency, for a certain fixed time.
Details Starting Conditions

1. When starting compressor for heating.
2. When the operating mode changes to cooling from heating.
3. When starting compressor for rushing defrosting or resetting.
4. When starting compressor for the first time after the reset with the power is ON.
5. When starting compressor for heating next to the suspension of defrosting.
6. When starting compressor next to the fault of switching over cooling/heating.

3.5 Discharge Pipe Temperature Control

Outline The discharge pipe temperature is used as the internal temperature of the compressor. If the
discharge pipe temperature rises above a certain level, the upper limit of frequency is set to
keep the discharge pipe temperature from rising further.
Details
Stop zone
A°C
B°C
Dropping zone
C°C
Keep zone
D°C
Up zone
E°C
Reset zone
Discharge pipe
temperature
Zone Control
Stop zone When the temperature reaches the stop zone, the compressor stops.
Dropping zone The upper limit of frequency decreases.
Keep zone The upper limit of frequency is kept.
Up zone The upper limit of frequency increases.
Reset zone The upper limit of frequency is cancelled
FTXC* BV1B
20/25/35 50/60/71
A (°C) 110 118
B (°C) 103 108
C (°C) 98 103
D (°C) 93 97
E (°C) 88 85

3.6 Input Current Control

Outline The microcomputer calculates the input current while the compressor is running, and sets the
frequency upper limit based on the input current.
Details
Compressor Stop
(A)
Stop zone
A
Dropping zone
Keep zone
C
Input current Reset zone

 Frequency control in each zone
Zone Control
Stop zone After the input current remains in the stop zone for 2.5 seconds, the compressor is stopped.
Dropping The upper limit of the compressor frequency is defined as operation frequency – 2 Hz.
After this, the output frequency is lowered by 2 Hz every second until it reaches the keep zone.
Keep zone The present maximum frequency goes on.
Reset zone Limit of the frequency is cancelled.
Mode (A)FTXC20/25 (A)FTXC35 (A)FTXC50/60/71

A 14.00 14.00 11.50
Cooling B 6.00 6.50 10.00
C 5.25 5.75 9.00
Mode (A)FTXC20/25 (A)FTXC35 (A)FTXC50/60/71

A 14.00 14.00 11.50
Heating B 6.75 7.75 10.00
C 6.00 7.00 9.00
 Limitation of current dropping and stop value according to the outdoor temperature
 The current drops when outdoor temperature becomes higher than a certain level
(depending on the model).

3.7 Freeze-up Protection Control

Outline During cooling operation, the signals sent from the indoor unit control the operating frequency
limitation and prevent freezing of the indoor heat exchanger. The signal from the indoor unit is
divided into zones.
Details The operating frequency limitation is judged with the indoor heat exchanger temperature.
Indoor heat exchanger
thermistor temperature
13°C
Reset zone
A°C
Up zone
B°C
Keep zone
C°C
Dropping zone
0°C
Stop zone
Zone Control
Up zone The upper limit of frequency increases
Keep zone The upper limit of frequency is kept
Dropping zone The upper limit of frequency decreases
Stop zone When indoor coil temperature <0°C for >80s, compressor is stopped
A (°C) B (°C) C (°C)

All outdoor units 7 5 3

3.8 Heating Peak-cut Control

During heating operation, the signals being sent from the indoor unit allow the operating
frequency limitation and prevent abnormal high pressure. (The signal from the indoor unit must
be divided as follows.)
Details Conditions for Start Controlling

Judge the controlling start with the indoor heat exchanger temperature after 2 sec. from
operation start.
Control in Each Zone
The heat exchange intermediate temperature of indoor unit controls the following.
Stop zone
A°C
B°C
Dropping zone
C°C
Keep zone
D°C
Heat exchanger Up zone
thermistor E°C
Reset zone
temperature
Zone Control
Stop zone When indoor coil temperature stop zone, the compressor stops
Dropping zone The upper limit of frequency decreases
Keep zone The upper limit of frequency is kept
Up zone The upper limit of frequency increases
RXC20/25/35BV1B RXC50/60/71BV1B
A (°C) 65 60
B (°C) 53 53
C (°C) 50 50
D (°C) 48 48
E (°C) 43 43

3.9 Outdoor Fan Control

1. Fan ON control to cool down the electrical box
The outdoor fan is turned ON when the electrical box temperature is high while the
compressor is OFF.
2. Fan OFF delay when stopped

The outdoor fan is turned OFF 70 seconds after the compressor stops.
3. Fan speed control for pressure difference upkeep

The rotation speed of the outdoor fan is controlled for keeping the pressure difference during
cooling operation with low outdoor temperature.
 When the pressure difference is low, the rotation speed of the outdoor fan is reduced.
 When the pressure difference is high, the rotation speed of the outdoor fan is controlled
as well as normal operation.
4. Fan speed control during forced cooling operation

The outdoor fan is controlled as well as normal operation during forced cooling operation.
5. Fan speed control during POWERFUL operation

The rotation speed of the outdoor fan is increased during POWERFUL operation.
6. Fan speed control during indoor unit quiet operation

The rotation speed of the outdoor fan is reduced by the command of the indoor unit quiet
operation.
7. Fan ON/OFF control when operation (cooling, dry) starts/stops

The outdoor fan is turned ON when the operation starts. The outdoor fan is turned OFF
when the operation stops.
8. Fan control when defrosting
9. Fan control when the compressor starts for heating

3.10 Liquid Compression Protection Function

Outline In order to increase the dependability of the compressor, the compressor is stopped according
to the outdoor temperature.
Details Operation stops depending on the outdoor temperature.

The compressor turns off under the conditions that the system is in cooling operation and
outdoor temperature is below X°C.
X refer to table below based on models
RXC35BV1B Others
Temperature 7°C 0°C
3.11 Defrost Control

Defrosting is carried out by the cooling cycle (reverse cycle). The defrosting time or outdoor
heat exchanger temperature must be more than its fixed value when finishing.
Details Conditions for Starting Defrost

The starting conditions must be made with the outdoor air temperature and heat exchanger
temperature. Under the conditions that the system is in heating operation, 6 minutes after the
compressor is started and more than 28 minutes of accumulated time pass since the start of the
operation or ending the defrosting.
Conditions for Canceling Defrost
The judgment must be made with heat exchanger temperature. (4°C-22°C)
PI control
Frequency
0Hz B
0Hz
A D C
Compressor ON
OFF
ON
Four way valve
OFF
5sec. 5sec.
ON
Fan
OFF
E H
F G
Electronic expansion
valve opening Initial opening
Time (sec) Pulse

Class
A B C D E F G H
RXC20/25 80 60 100 690 450 380 280 280
RXC35 80 60 70 690 450 300 200 200
RXC50/60/71 50 60 60 690 400 450 450 450

3.12 Electronic Expansion Valve Control

3.12.1 Summary of Electronic Expansion Valve Control
Controlling the electronic expansion valve is to ensure the reliability while optimizing the refrigerating cycle responding
to the operation status. The summary of electronic expansion valve control is shown as below.
3RZHU213RZHU6XSSO\5HVHW
,QLWLDOL]HG IXOO\FORVHG DV3RZHU6XSSO\21
3URFHVVHVZKLOHWKHFRPSUHVVRULVRSHUDWLQJ
2SHQFRQWURO
(OHFWURQLFH[SDQVLRQ +LJKGLVFKDUJHSLSH
YDOYHFRQWURO WHPSHUDWXUHFRQWURO
DWVWDUWXS
5HKHDW
GHKXPLGLrFDWLRQ
FRQWURO
)HHGEDFNFRQWURO 'HIURVWFRQWURO
3URFHVVZKHQ
+LJKGLVFKDUJHSLSH WKHFRPSUHVVRUVWRSV
7DUJHWGLVFKDUJH WHPSHUDWXUHFRQWURO
SLSH GRHVQRWIXQFWLRQ
WHPSHUDWXUH ZKHQWKHGLVFKDUJH
3UHVVXUH
FRQWURO SLSHWKHUPLVWRULV
HTXDOL]DWLRQFRQWURO
GLVFRQQHFWHG

3.12.2 Full Close as Power Supply ON

When the power is turned ON, the electronic expansion valve is initialized to position the valve opening and
facilitate pressure equalization. (Prevent the compressor from being locked by start-up with differential pressure)
Processes as power supply ON

Turn the power ON, close 700 pluses and set the current opening at 0 pulse.
Open 400 pulses after the full close process completed.
3RZHU21
SXOVHV
SXOVHV
SXOVH
/RZHUOLPLWRIWKH
HOHFWURQLFH[SDQVLRQ
YDOYH YDOYHERG\
VWURNH
Process after resuming from stand-by electricity saving (suspend) mode

Set the electronic expansion valve opening at 400 pulses after resuming from stand-by electricity saving mode.
3.12.3 Pressure Equalization Control

When the compressor is switched from ON to OFF, open the electronic expansion valve to facilitate pressure
equalization while preventing the sound produced from refrigerant flow at pressure equalization.
Summary of operation
Open the electronic expansion valve in a phased manner for 90-120 seconds when operation stop (including abnormal
stoppage) or the thermostat is turned OFF.
Fully closedopen 400 pluses

3.12.4 Initialization as Power Supply On
The electronic expansion valve is initialized (fully closed) when the power is turned on. Then,
the valve opening position is set and the pressure is equalized.
3.12.5 Pressure Equalizing Control

When the compressor is stopped, the pressure equalizing control is activated. The electronic
expansion valve opens and the pressure is equalized.
3.12.6 Opening Limit Control

The maximum and minimum opening of the electronic expansion valve are limited.
Electronic expansion
RXC20/25/35/50/60/71BV1B
valve opening (pulse)
Maximum 470
Minimum 52
3.12.7 Starting Operation Control

The electronic expansion valve opening is controlled when the operation starts, thus preventing
superheating or liquid compression.
3.12.8 Control when the Frequency Changes

When the target discharge pipe temperature control is active, if the target frequency changes to
a specified value in a certain period of time, the target discharge pipe temperature control is
canceled and the target opening of the electronic expansion valve is changed according to the
frequency shift.

3.12.9 High Discharge Pipe Temperature Control

When the compressor is operating, if the discharge pipe temperature exceeds a certain value,
the electronic expansion valve opens and the refrigerant runs to the low pressure side. This
procedure lowers the discharge pipe temperature by cooling the compressor with refrigerant.
$
FRUUHFWLRQ +LJKGLVFKDUJHSLSHWHPS
FRQWUROVWDUWWHPSHUDWXUH
IDFWRU
5HVHW]RQH 'URSSLQJ]RQH
%
+LJKGLVFKDUJHSLSHWHPS
FRUUHFWLRQ FRQWUROUHOHDVHWHPSHUDWXUH
IDFWRU
RXC20/25/35 RXC50/60/71
A 102 105
B 100 100
3.12.9-1 Determine Zones
嵣&RPSUHVVRULVRSHUDWLQJ
$1' 'URSSLQJ]RQH
嵣'LVFKDUJHSLSHWHPS!&
嵣&RPSUHVVRUVWRSV
嵣'LVFKDUJHSLSHWHPS۹& 5HVHW]RQH
25
嵣'LVFRQQHFWLRQRIGLVFKDUJHSLSH
WKHUPLVWRU

3.12.9-2 Process for Each Zone

Dropping zone: Open the current opening by +20 pulses every 30 seconds
Reset zone: Release control and shift to target discharge pipe temperature control

3.12.10 Discharge Pipe Thermistor Disconnection Control

Outline The disconnection of the discharge pipe thermistor is detected by comparing the discharge pipe
temperature with the condensing temperature. If the discharge pipe thermistor is disconnected,
the electronic expansion valve opens according to the outdoor temperature and the operation
frequency, operates for a specified time, and then stops.
After 3 minutes, the operation restarts and checks if the discharge pipe thermistor is
disconnected. If the discharge pipe thermistor is disconnected, the system stops after operating
for a specified time.
If the disconnection is detected repeatedly, the system is shut down. When the compressor runs
for 60 minutes without any error, the error counter is reset.
Details Determining thermistor disconnection

When the starting control (A seconds) finishes, the detection timer for disconnection of the
discharge pipe thermistor (B seconds) starts. When the timer is over, the following adjustment is
made.
When the following condition is fulfilled, the discharge pipe thermistor disconnection is
ascertained.
For cooling mode:

Discharge pipe temperature + C°C < outdoor heat exchanger temperature
RXC20/25/35/50/60/71
A 10
B 720
C 6
For heating mode:

Discharge pipe temperature + D°C < indoor heat exchanger temperature
RXC20/25/35 RXC50/60/71
D 6 6
When the thermistor is disconnected

When the disconnection is ascertained, the compressor continues operation for 9 minutes and
then stops.
If the compressor stops repeatedly, the system is shut down.
3.12.11 Target Discharge Pipe Temperature Control

The target discharge pipe temperature is obtained from the indoor and outdoor heat exchanger
temperature, and the electronic expansion valve opening is adjusted so that the actual
discharge pipe temperature becomes close to the target discharge pipe temperature. (Indirect
SH (superheating) control using the discharge pipe temperature)
The target discharge pipe

SC temperature is set as to become
(Subcooling) the target SH.
The inclination does not change
depending on the operating condition.
SH
(Superheating)
The electronic expansion valve opening and the target discharge pipe temperature are adjusted
every A seconds. The opening degree of the electronic expansion valve is adjusted by the
following.
 Target discharge pipe temperature
 Actual discharge pipe temperature
 Previous discharge pipe temperature
A (seconds) 10 ~ 20
(depending on the model)

3.13 Malfunctions
3.13.1 Sensor Malfunction Detection
Sensor malfunction can be detected in the following thermistors in open or short circuit.
1. Outdoor heat exchanger thermistor
2. Discharge pipe thermistor
3. Radiation fin thermistor
4. Outdoor temperature thermistor
3.13.2 Detection of Overcurrent and Overload

Outline In order to protect the inverter, an excessive output current is detected in wire labelled as No 1
at outdoor terminal block and the OL temperature is observed to protect the compressor.
Details  If the inverter current exceeds A A, the system shuts down the compressor.
 If the OL (compressor head) temperature exceeds B°C, the compressor stops.
RXC20/25/35 RXC50/60/71
A 14.0 11.5
B 120.0

DAMA-SM-20-002
Part 4
Remote Controller
1. Applicable Remote Controller ...............................................................55
2. BRC52B66 ............................................................................................56
Part 4 Remote Controller 54

Applicable Remote Controller DAMA-SM-20-002
1. Applicable Remote Controller

Series Model Name Remote Controller Reference Page
(A)FTXC20/25/35BV1B BRC52B66
FTK(X)A
(A)FTXC50/60/71BV1B
55 Remote Controller
BRC52B66 DAMA-SM-20-002
2. BRC52B66
GV: DENV
FTXC20/25/35/50/60/71BV1B
REMOTE CONTROLLER OVERVIEW

For heating model
IR Signal Transmitter
• To enable signal
transmission, direct the
transmitter at the indoor
unit.
Note that in condition
Display (LCD)
where there is an obstacle
• Display the current that blocks between the
settings. transmitter and the indoor
(This illustration shows the unit, signal transmission
full display of the LCD might not be successful.
panel, including functions
for applicable remote
controller models only). Temperature Setting Button
• Increase / Decrease the
ON/OFF Button temperature setting.
• Start/Stops the operation. ON/OFF
POWERFUL Button
FAN Button TEMP • Enable / Disable
• Changes the operating fan POWERFUL function.
speed.
FAN POWERFUL SWING
UP-DOWN SWING Button
QUIET Button
• Enable / Disable QUIET QUIET MODE SLEEP • Direct the air flow in up-
function. down direction.
Mode Button SLEEP Button

• Change between the LED ECO+ • Enable / Disable SLEEP
available operating modes.. TIMER function.
ON OFF
LED Button CANCEL CLOCK CANCEL

ECO+ Button
• Change the indication • Enable / Disable ECO +
display. function.
ON Timer Button OFF Timer Button

• Enable / Disable and • Enable / Disable and
change ON Timer setting. change OFF Timer setting.
CLOCK Button
• Changes RTC selling.
56 Remote Controller
DAMA-SM-20-002
Part 5
Service Diagnosis
1. General Problem Symptoms and Check Items .....................................58
2. Troubleshooting with LED .....................................................................59
2.1 Indoor Unit..............................................................................................59
2.2 Outdoor Unit ...........................................................................................60
3. Error Diagnosis .....................................................................................60
3.1 To enter error diagnosis .........................................................................60
4. Troubleshooting ....................................................................................61
4.1 Error Codes and Description ..................................................................61
4.2 Indoor Unit PCB Abnormality .................................................................63
4.4 Indoor Fan Motor (DC Motor) or Related Abnormality ...........................65
4.7 Low-voltage Detection or Over-voltage Detection..................................68
4.8 Signal Transmission Error (Between Indoor Unit and Outdoor Unit)......69
4.9 Installation error......................................................................................71
4.10 Outdoor Unit PCB Abnormality...............................................................72
4.11 OL Activation (Compressor Overload) ...................................................73
4.12 Compressor Lock ...................................................................................75
4.13 DC Fan Lock ..........................................................................................76
4.14 Input Overcurrent Detection ...................................................................77
4.16 High Pressure Control in Cooling ...........................................................80
4.17 Compressor System Sensor Abnormality ..............................................82
4.18 Position Sensor Abnormality ..................................................................83
4.23 Electrical Box Temperature Rise............................................................92
4.24 Radiation Fin Temperature Rise ............................................................93
4.25 Output Overcurrent Detection ................................................................94
4.26 Four Way Valve Abnormality..................................................................96
5. Actuator Check......................................................................................98
5.1 Thermistor Resistance Check ................................................................98
5.2 Power Supply Waveform Check.............................................................99
5.3 Electronic Expansion Valve Check.........................................................99
5.4 Four Way Valve Performance Check ...................................................100
5.5 Inverter Unit Refrigerant System Check...............................................101
5.6 Rotation Pulse Check on the Outdoor Unit PCB ..................................101
5.7 Installation Condition Check.................................................................102
5.8 Discharge Pressure Check...................................................................102
5.9 Outdoor Fan System Check .................................................................103
5.10 Main Circuit Short Check......................................................................103
5.11 Power Module Check ...........................................................................105
Part 5 Service Diagnosis 57

DAMA-SM-20-002 General Problem Symptoms and Check Items
1. General Problem Symptoms and Check Items

Reference
Symptom Check Item Details
Page
The unit does not operates. Check the power supply. Check if the rated voltage is supplied. —
Check the type of the indoor unit. Check if the indoor unit type is compatible
—
with the outdoor unit.
Check the outdoor temperature. Cooling operation is not available when the
outdoor temperature is out of the operation
119
limit. Check the reference page for the
operation limit.
Diagnose with remote controller
— 61
indication
Check the remote controller Check if address settings for the remote
addresses. controller and indoor unit are correct. —
Operation sometimes stops. Check the power supply. A power failure of 2 to 10 cycles can stop air
—
conditioner operation. (Operation lamp OFF)
Check the outdoor temperature. Cooling operation is not available when the
outdoor temperature is out of the operation
119
limit. Check the reference page for the
operation limit.
— 61
indication.
The unit operates but does Check for wiring and piping errors in
not cool. the connection between the indoor — —
and outdoor units.
Check for thermistor detection errors. Check if the thermistor is mounted securely. —
Check for faulty operation of the Set the unit to cooling operation, and check
electronic expansion valve. the temperatures of the liquid pipe to see if —
the electronic expansion valve works.
— 61
indication.
Diagnose by service port pressure Check for refrigerant shortage.
—
and operating current.
Large operating noise and Check the output voltage of the power
vibrations module. — 105
Check the power module. — —

Check the installation condition. Check if the required spaces for installation
(specified in the installation manual) are —
provided.
Service Diagnosis 58
Troubleshooting with LED DAMA-SM-20-002
2. Troubleshooting with LED

2.1 Indoor Unit
Operation Lamp The operation lamp blinks when any of the following errors is detected.
1. A protection device of the indoor or outdoor unit is activated, or the thermistor malfunctions.
2. A signal transmission error occurs between the indoor and outdoor units.
In either case, conduct the diagnostic procedure described in the following pages.
LED INDICATION LIGHTS
ON/OFF
switch
*Changed to relevant image (FTKA or FTXA)
2.2 Outdoor Unit

The outdoor unit has a green LED (LED A) on the PCB.
When the microcomputer works in order, the LED A blinks.
Refer to pages 117, 118 for the location of LED A
LED A
LED A
59 Service Diagnosis
DAMA-SM-20-002 Error Diagnosis
3. Error Diagnosis
3.1 To enter error diagnosis
GV : Press [Timer CANCEL] to scroll to next
°C
TIMER
OFF
CANCEL
GV (FT(X)A)
Notes 1. A short beep and two consecutive beeps indicate non-corresponding codes.
2. To return to the normal mode.
GV : Press [Timer CANCEL] for 5 seconds
When the remote controller is left untouched for 60 seconds, it also returns to the normal mode.
Troubleshooting DAMA-SM-20-002
4. Troubleshooting
4.1 Error Codes and Description
Error
Description Reference Page
Codes
System
00 Normal condition -
U2 Low-voltage detection or over-voltage detection 68
U4 Signal transmission error (between indoor unit and outdoor unit) 69
UA Installation error (between indoor unit and outdoor unit) 71

Indoor Unit
A1 Indoor unit PCB abnormality 63
A5 Freeze-up protection control 64
A6 Indoor fan motor (DC motor) or related abnormality 65
C4 Indoor heat exchanger thermistor or related abnormality 66
C9 Room temperature thermistor or related abnormality 67

Outdoor Unit
E1 Outdoor unit PCB abnormality 72
E5  OL activation (compressor overload) 73
E6  Compressor lock 75
E7  DC fan lock 76
E8 Input overcurrent detection 77
F3 Discharge pipe temperature control 78
F6 High pressure control in cooling 80
EA Four way valve abnormality 96
H0 Compressor sensor system abnormality 82
H6 Position sensor abnormality 83
H9 Outdoor temperature thermistor or related abnormality 84
J3  Discharge pipe thermistor or related abnormality 86
J6 Outdoor heat exchanger thermistor or related abnormality 88
L3 Electrical box temperature rise 92
L4 Radiation fin temperature rise 93
L5 Output overcurrent detection 94
P4 Radiation fin thermistor or related abnormality 90

Displayed only when the system is shut down.
DAMA-SM-20-002 Troubleshooting
 Eror Code Definition

Error Code Checklist Meaning
00  Normal
A1  Indoor PCB error
A3 Drain pump abnormal
A5  Antifreeze
A6  Indoor fan motor abnormal
AH Electrical air cleaner abnormal
C4  Indoor heat exchanger (1) thermistor short / open
C5 Indoor heat exchanger (2) thermistor short / open
C7 Louver limit switch error
C9  Indoor room thermistor short / open
E1  Outdoor PCB error
E3 High pressure protection
E4 Low pressure protection
E5  Compressor motor lock / compressor overload
E6  Compressor start-up error
E7  Outdoor DC fan motor lock
E8  AC input overcurrent
E9 EXV error
EA  4 way valve error
F3  Discharge pipe overheat
F6  Heat exchanger overheat
H0  Compressor sensor system error
H3 High pressure switch error
H6  Compressor feedback detection error
H7 Fan motor overload / overcurrent / sensor abnormal
H8 AC current sensor error
H9  Outdoor air thermistor short / open
J1 Pressure sensor error
J3  Compressor discharge pipe thermistor short / open / misplaced
J5 Suction pipe thermistor short / open
J6  Outdoor heat exchanger thermistor short / open
J7 Subcooling heat exchanger thermistor short / open
J8 Liquid pipe thermistor short / open
J9 Gas pipe thermistor short / open
L1 Inverter outdoor PCB error
L3  Outdoor control box overheat
L4  Heat sink overheat
L5  IPM error / IGBT error
L8 Inverter compressor overcurrent
L9 Compressor overcurrent prevention
LC Communication error (outdoor control PCB and inverter PCB)
P1 Open phase or voltage unbalance
P4  Heat sink thermistor short / open
PJ Capacity setting error
U0 Insufficient gas
U2  DC voltage out of range
U4  Communication error
U7 Communication error (outdoor control PCB and IPM PCB)
Installation error (wrong combination of ID and OD units /
UA 
wrong or defective ID/OD PCB installed)
UF Piping & wiring installation mismatch / wrong wiring / insufficient gas
4.2 Indoor Unit PCB Abnormality

Error Code A1
Description Indoor PCB Abnormality
Method of Error The system checks if the circuit works properly within the microcomputer of the indoor unit.
Detection
Error Decision ON/OFF switch malfunction.

Conditions
Possible root 1. Defective indoor unit PCB.

cause 2. Defective ON/OFF switch.
Troubleshooting
Be sure to turn off the power switch before connecting or disconnecting
Cautio n connectors, or parts may be damaged.
Turn off the power

supply
Press the ON/OFF

switch
Yes Turn on the power

Can be pressed?
supply
No
No
Remove the casing Is error repeat? Completed
Yes
Press the ON/OFF

switch again
Turn off the power
supply & replace the
indoor unit PCB
(Display PCB)
Is the ON/OFF No
switch can be Replace the
pressed? indoor unit PCB.
(Display PCB) Turn on the power
supply
Yes
Turn on the power

supply
No
Is error repeat? Completed
No Yes
Is error repeat? Completed
Replace the indoor unit PCB.
(Control PCB)
Yes Replace the indoor unit PCB.

(Control PCB)
4.3 Freeze-up Protection Control

Error Code A5
Method of Error During cooling operation, the freeze-up protection control (operation halt) is activated according
Detection to the temperature detected by the indoor heat exchanger thermistor.
High pressure control (heat pump model only).
During heating operations, the temperature detected by the indoor heat exchanger.
Thermistor is used for the high pressure control (stop, outdoor fan stop, etc.).
Error Decision During cooling operation, the indoor heat exchange temperature is below 0°C.
Conditions High pressure control
During heating operations, the temperature detected by the indoor heat exchanger thermistor is
above 61°C.
Supposed  Indoor Short-circuited air

Causes  Clogged air filter of the indoor unit
 Dust accumulation on the indoor heat exchanger
 Defective indoor heat exchanger thermistor
 Defective indoor unit PCB
Troubleshooting
Caution connectors, or parts may be damaged.
Check the air passage.
YES
Is there any short circuit? Provide sufficient air passage.
NO
Check the air filter.
YES
Dirty? Clean the air filter.
NO
Check the dust accumulation on
the indoor heat exchanger.
YES
Dirty? Clean the indoor heat
exchanger.
NO
Check No. 01
Check the indoor heat exchanger
thermistor.
As
described in the NO
thermistor characteristic Replace the indoor heat
chart? exchanger thermistor.
YES
Replace the indoor unit PCB
(control PCB).
Error Code Error Code

Outdoor Indoor A5
Mode COOL Mode COOL
COMP ON Set Point 16.0°C
Fan Speed ON Fan SP-Set H
Suct Temp
EvaTemp: CHECK
Fan1SP
1145d21h58m16s DEMO\DEMO052.TXT
2020/06/22 16:45:01 60Hz EN03
Reference Check No.01 Refer to P.98
Note When replacing the defective thermistor(s), replace the thermistor as ASSY.
Refer to Appendix when using the transmission monitor to identify the error code.
4.4 Indoor Fan Motor (DC Motor) or Related Abnormality

Error Code A6
Description Indoor Fan Motor Abnormality
Method of Error The rotation speed detected by the Hall IC during fan motor operation is used to determine
Detection abnormal fan motor operation.
Error Decision The detected rotation speed does not reach the demanded rotation speed of the target tap, and
Conditions is less than 50% of the maximum fan motor rotation speed.
Possible Root 1. Indoor fan motor winding short, or the motor lead wire broken.
Causes 2. Indoor PCB faulty.
Troubleshooting
Turn off power supply and

rotate fan by hand
No
Does it rotate? Change fan motor.
Yes
Check fan motor connector condition
Does it connect No
Connect correctly.
properly?
Yes
(control PCB) and turn on power
No Complete.
Is error repeated?
Yes
Change Fan motor.

Outdoor Indoor A6
Mode COOL Mode COOL
Suct Temp
EvaTemp1
Fan1SP CHECK
2020/06/22 16:45:01 60Hz EN03
Note Refer to Appendix when using the transmission monitor to identify the error code.
4.5 Thermistor or Related Abnormality (Indoor Unit)

Error Code C4
Description Indoor Heat Exchange Thermistor Short/Open.
Method of Error The temperature detected by the thermistors determine thermistor errors.
Detection
Error Decision The resistance of the thermistor is out of range (0 Ω or ∞ Ω)

Conditions
Supposed  Disconnection of connector

Causes  Defective thermistor(s)
Troubleshooting
Check the connection of

connectors.
NO
Normal ? Correct the connection.
YES
Check No. 01
Check the thermistor resistance
value.
NO
Normal ? Replace the defective
thermistor.
YES
(control PCB).
C4 : Indoor heat exchanger thermistor

Outdoor Indoor C4
Mode COOL Mode COOL
Suct Temp
EvaTemp : CHECK
Fan1SP
2020/06/22 16:45:01 60Hz EN03
4.6 Thermistor or Related Abnormality (Indoor Unit)

Error Code C9
Description Indoor Heat Exchange Thermistor Short/Open.
Method of Error The temperature detected by the thermistors determine thermistor errors.
Detection
Error Decision The resistance of the thermistor is out of range (0 Ω or ∞ Ω)

Conditions
Supposed  Disconnection of connector

Troubleshooting
Check the connection of

connectors.
NO
Normal ? Correct the connection.
YES
Check No. 01
Check the thermistor resistance
value.
NO
Normal ? Replace the defective
thermistor.
YES
(control PCB).
C9 : Room temperature thermistor

Outdoor Indoor C9
Mode COOL Mode COOL
Suct Temp CHECK
EvaTemp1
Fan1SP
2020/06/22 16:45:01 60Hz EN03
4.7 Low-voltage Detection or Over-voltage Detection

Error Code U2
Method of Error Low-voltage detection:
Detection An abnormal voltage drop is detected by the DC voltage detection circuit.
Over-voltage detection:
An abnormal voltage rise is detected by the DC over-voltage detection circuit.
Error Decision Low-voltage detection:

Conditions  The voltage detected by the DC voltage detection circuit is below 180 - 196 V (depending on
the model).
 The compressor stops if the error occurs, and restarts automatically after 3-minute standby.
Over-voltage detection:
 An over-voltage signal is fed from the over-voltage detection circuit to the microcomputer.
 The compressor stops if the error occurs, and restarts automatically after 3-minute standby.
Supposed
Causes  Power supply voltage out of specification  Short circuit inside the fan motor winding
 Defective DC voltage detection circuit  Noise
 Defective over-voltage detection circuit  Momentary drop of voltage
 Defective PAM control part  Momentary power failure
 Disconnection of compressor harness  Defective outdoor unit PCB
Troubleshooting
Check the power supply voltage.
Is the
voltage fluctuation NO
within ±10% from the Correct the power supply.
rated value?
YES
Check the connection of the
compressor harness.
Loose or YES
disconnected? Reconnect the harness.
NO
Does the
NO
outdoor fan rotate Replace the outdoor fan motor
smoothly? and the outdoor unit PCB
(main PCB).
YES
(Precaution before turning on the power again)
Make sure the power has been off for at
least 30 seconds.
Turn on
the power. System YES Disturbance factors
restarted? (Repeat a few * Noise Check for such factors for a
times.) * Power supply distortion long term.
NO
Replace the outdoor

unit PCB (main PCB).

Outdoor U2 Indoor
Mode COOL Mode COOL
2020/06/22 16:45:01 60Hz EN03
4.8 Signal Transmission Error (Between Indoor Unit and

Outdoor Unit)
Error Code U4
Method of Error The signal transmission data received from the outdoor unit is checked whether it is normal.
Detection
Error Decision The data sent from the outdoor unit cannot be received normally, or the content of the data is
Conditions abnormal.
Supposed  Power supply voltage out of specification

Causes  Reduction of power supply voltage
 Wiring miss connection
 Breaking of the connection wires between the indoor and outdoor units wire no.3/SIG.
 Defective outdoor unit PCB
 Short circuit inside the fan motor winding
 Disturbed power supply waveform
Troubleshooting
Is the
voltage fluctuation NO
within ±10% from the Correct the power supply.
rated value?
YES
Check the connection wires
between the indoor unit and the
outdoor unit.
YES
Is there any wiring error? Correct the connection wires
between the indoor unit and
the outdoor unit.
NO
Check the voltage of the

connection wires on the indoor
terminal strip between No. 1
wire no.3/SIG, and between No. 2
wire no.3/SIG.
NO
Properly insulated? Replace the connection wires
between the indoor unit and
outdoor unit.
YES
Check the LED A on the outdoor

unit PCB.
Continuously ON or OFF
Is LED A blinking? Replace the outdoor unit PCB
(main PCB).
Blink
Rotate the
outdoor fan manually. NO
Does the outdoor fan rotate Replace the outdoor fan motor
smoothly? and the outdoor unit PCB
(main PCB).
YES
Check No.11
Check the power supply
waveform.
NO
Is there any disturbance? Replace the indoor unit PCB
(control PCB).
YES
Locate and eliminate the
cause of the disturbance of
the power supply waveform.
4.9 Installation error

Error Code UA
Method of Error The supply power is detected for its requirements (pair type is different from multi type) by the
Detection indoor/outdoor transmission signal.
Error Decision The pair type and multi type are interconnected.
Conditions
Supposed  Wrong models interconnected

Causes  Wrong wiring of connecting wires
 Wrong indoor unit PCB or outdoor unit PCB mounted
Troubleshooting
Check the combination of the

indoor and outdoor unit.
NO
OK? Match the compatible models.
YES
Are the
connecting wires NO
Correct the connection.
connected properly?
YES
Check the part numbers of the
indoor and outdoor unit PCB
with the Parts List.
If not matched, change for the
correct PCB.
4.10 Outdoor Unit PCB Abnormality

Error Code E1
Method of Error  The system checks if the microcomputer is working in order.
Detection  The system checks if the zero-cross signal comes in properly.
Error Decision  The microcomputer program runs out of control.

Conditions  The zero-cross signal is not detected.
Supposed  Defective outdoor unit PCB

Causes  Noise
 Momentary drop of voltage
 Momentary power failure
Troubleshooting
Turn on the power.
YES
Error again? Replace the outdoor unit PCB
(main PCB).
NO
Check if the outdoor unit is

grounded.
NO
Grounded? Ground the system.
YES
The cause can be external
factors other than malfunction.
Investigate the cause of noise.
4.11 OL Activation (Compressor Overload)

Error Code E5
Description OL activation (compressor overload).
Method of Error A compressor overload is detected through compressor OL.

Detection
Error Decision  If the error repeats, the system is shut down.

Conditions  Reset condition: Continuous run for about 60 minutes without any other error
Possible Root 1. Disconnection of discharge pipe thermistor

Causes 2. Defective discharge pipe thermistor
3. Disconnection of connector S40
4. Disconnection of 2 terminals of OL (Q1L)
5. Defective OL (Q1L)
6. Broken OL harness
7. Defective electronic expansion valve or coil
8. Defective four way valve or coil
9. Defective outdoor unit PCB
10. Refrigerant shortage
11. Water mixed in refrigerant
12. Defective stop valve
Troubleshooting
Discharge
pipe thermistor YES
Insert the thermistor in
disconnected? position.
NO
NG Replace the discharge pipe

Check the thermistors thermistor.
• Discharge pipe thermistor
OK
Connectors are NO Connect the connectors

properly connected? • Connector S40 properly.
• 2 terminals of OL (Q1L)
YES
Disconnect the connector S40

from the PCB.
Check Resistance
the resistance ∞ Disconnect the 2 terminals
between the 2 terminals on of the OL (Q1L).
connector S40.
Nearly 0 Ω
Check the
Resistance
resistance
∞
between the 2 Replace the OL (Q1L)
terminals of the OL
(Q1L).
Nearly 0 Ω
Replace the OL harness.
Check the electronic NG Replace the electronic expansion
expansion valve. valve or the coil
OK
NG applicable to FTXA/FTXC (mode)

Check the four way Replace the four way valve or the
valve coil.
Replace the outdoor unit PCB
(main PCB).
OK
NG
Check the refrigerant Refer to the refrigerant line
line. • Refrigerant shortage check procedure.
• Water mixed
• Stop valve
OK
Replace the outdoor unit PCB
(main PCB).
4.12 Compressor Lock

Error Code E6
Description Compressor lock.
Method of Error A compressor lock is detected by checking the compressor running condition through the
Detection position detection circuit.
Error Decision  If the error repeats, the system is shut down.

Conditions  Reset condition: Continuous run for about 11 minutes without any other error.
Supposed  Closed stop valve

Causes  Compressor locked
 Disconnection of compressor harness
Troubleshooting
YES
Stop valve closed? Open the stop valve.
NO
Turn off and turn on the power

to restart the system
Emergency
YES
stop without compressor Replace the compressor. /
running? outdoor unit PCB (main PCB)
NO
System shut NO
down after errors repeated Check the electronic expansion
several times? valve coil. Go to Check No. 12.
YES
Replace the compressor. /
outdoor unit PCB (main PCB)
4.13 DC Fan Lock

Error Code E7
Method of Error An error is determined with the high-voltage fan motor rotation speed detected by the Hall IC.
Detection
Error Decision  The fan does not start in about 30 ~ 60 seconds (depending on the model) even when the
Conditions fan motor is running.
 If the error repeats, the system is shut down.
 Reset condition: Continuous run for about 11 minutes without any other error
Supposed  Disconnection of the fan motor

Causes  Foreign matter stuck in the fan
 Defective fan motor
Troubleshooting
Fan motor connector YES

disconnected? Turn off the power and
reconnect the connector.
NO
Foreign matters in or YES

around the fan? Remove the foreign
matters.
NO
Turn on the power.
Rotate the fan.
Fan rotates NO
smoothly? Replace the outdoor fan
motor.
YES
Check No. 16
Check the rotation pulse input on
the outdoor unit PCB (main PCB).
NO
Pulse signal generated? Replace the outdoor fan
motor.
YES
Replace the outdoor unit
PCB (main PCB).
4.14 Input Overcurrent Detection

Error Code E8
Description Input Overcurrent Detection
Method of Error An input overcurrent is detected by checking the input current value with the compressor
Detection running.
Error Decision The current exceeds 10 ~ 15 A (depending on the model) for 2.5 seconds with the compressor running.
Conditions The upper limit of the current decreases when the outdoor temperature exceeds a certain level.
Supposed  Outdoor temperature out of operation range

Causes  Defective compressor
 Defective power module
 Short circuit
Troubleshooting
Check No. 17
Check the installation condition.
Start operation and measure the

Input current.
Input current flowing NO Replace the outdoor

above its stop level? unit PCB (main PCB).
YES
Check No. 18
Check the discharge pressure.
Cautions: Be sure to turn off the power switch before connecting or disconnecting connectors, or parts
may be damaged.
An input overcurrent may result from wrong internal wiring. If the system is interrupted by an
input overcurrent after the wires have been disconnected and reconnected for part
displacement, check the wiring again.

Outdoor E8 Indoor
Mode COOL Mode COOL
Heat Exch
CT Current CHECK
INV-Temp
2020/06/22 16:45:01 60Hz EN03
4.15 Discharge Pipe Temperature Control

Error Code F3
Method of Error An error is determined with the temperature detected by the discharge pipe thermistor.
Detection
Error Decision  If the temperature detected by the discharge pipe thermistor rises above A°C, the
Conditions compressor stops.
 The error is cleared when the discharge pipe temperature has dropped below B°C.
Model RXC20/25/35
A (°C) B (°C)
(1) above 45 Hz 110 85
(2) 20 ~ 45 Hz 95 70
(3) below 20 Hz 90 65
Model RXC50/60/71
A (°C) B (°C)
(1) above 50 Hz (rising), 45 Hz (dropping) 113 80
(2) 21 ~ 50 Hz (rising), 16 ~ 45 Hz (dropping) 101 68
(3) below 21 Hz (rising), 16 Hz (dropping) 93 60
Supposed  Defective discharge pipe thermistor

Causes (Defective outdoor heat exchanger thermistor or outdoor temperature thermistor)
 Defective electronic expansion valve or coil
 Refrigerant shortage
 Water mixed in refrigerant
 Defective stop valve
Troubleshooting
Check No. 01 NG
Check the thermistors. Replace the defective
∗ Discharge pipe thermistor thermistor(s).
∗ Outdoor heat exchanger thermistor
OK ∗ Outdoor temperature thermistor
Check No. 12 NG
Check the electronic Replace the electronic
expansion valve. expansion valve or the coil.
OK
Check No. 14 NG
Check the refrigerant Refer to the refrigerant line
line. ∗ Refrigerant shortage check procedure.
∗ Water mixed
OK ∗ Stop valve

PCB (main PCB).

Outdoor F3 Indoor
Mode COOL Mode COOL
INV
DiscTemp CHECK
EEV
2020/06/22 16:45:01 60Hz EN03
4.16 High Pressure Control in Cooling

Error Code F6
Method of Error High-pressure control (operation halt, frequency drop, etc.) is activated in cooling mode if the
Detection temperature sensed by the outdoor heat exchanger thermistor exceeds the limit.
Error Decision  The temperature sensed by the outdoor heat exchanger thermistor rises above A°C.
Conditions  The error is cleared when the temperature drops below B°C.
A (°C) B (°C)
RXC20/25/35 61 55
RXC35 61 53
RXC50 61 55
RXC60 61 54
RXC71 61 55
Supposed  Installation space not large enough

Causes  Dirty outdoor heat exchanger
 Defective outdoor fan motor
 Defective stop valve
 Defective electronic expansion valve or coil
 Defective outdoor heat exchanger thermistor
 Defective outdoor unit PC
Troubleshooting
Check the installation space.
Check No. 17
Check the installation NG
Change the installation
condition. location or direction.
Clean the outdoor heat
OK exchanger.
Check No. 19 NG
Check the outdoor fan. Replace the outdoor fan
motor.
Reconnect the connector or
OK fan motor lead wires.
Check No. 18 NG
Check the discharge Replace the stop valve.
pressure.
OK
Check No. 12
Check the electronic NG
Replace the electronic
expansion valve. expansion valve or the coil.
OK PCB (main PCB).
Check No. 01
Check the outdoor heat NG
exchanger thermistor. Replace the outdoor heat
exchanger thermistor.
OK

PCB (main PCB).

Outdoor F6 Indoor
Mode COOL Mode COOL
HeatExch CHECK
CTCurrent
INV-Temp
2020/06/22 16:45:01 60Hz EN03
4.17 Compressor System Sensor Abnormality

Error Code H0
Method of Error The system checks the DC current before the compressor starts.
Detection
Error Decision  The voltage converted from the DC current before compressor start-up is out of the range
Conditions 0.5 ~ 4.5 V.
 The DC voltage before compressor start-up is below 50 V.
Supposed  Broken or disconnected harness

Causes  Defective outdoor unit PCB
Troubleshooting
Check the relay harness for the
compressor.
YES
Is the harness broken? Replace the harness.
NO
Turn off the power. Then, turn on

the power to restart the system.
Restart operation NO
and error displayed Not a malfunction.
again? Keep observing.
YES
PCB (main PCB).
4.18 Position Sensor Abnormality

Error Code H6
Description Position Sensor Abnormality
Method of Error A compressor start-up failure is detected by checking the compressor running condition through
Detection the position detection circuit.
Error Decision  The compressor fails to start in about 15 seconds after the compressor run command signal
Conditions is sent.
Supposed  Power supply voltage out of specification

Causes  Disconnection of the compressor harness
 Defective compressor
 Start-up failure caused by the closed stop valve
 Input voltage out of specified range
Troubleshooting
Turn off the power.
NO
Voltage as rated? Correct the power supply.
YES
Check No. 18
NO
OK? Replace the stop valve.
YES
Check No. 20
Check the short circuit of the
diode bridge.
NO
Normal? Replace the outdoor
unit PCB (main PCB).
YES
Check the connection.
Electrical
components or
NO
compressor harnesses Reconnect the electrical
connected as components or compressor
specified? harnesses as specified.
YES
PCB (main PCB) / compressor
4.19 Thermistor or Related Abnormality (Outdoor Unit)

Error Code H9
Description Thermistor or Related Abnormality (Outdoor Unit)
Method of Error This fault is identified based on the thermistor input voltage to the microcomputer.
Detection A thermistor fault is identified based on the temperature sensed by each thermistor.
Error Decision  The voltage between both ends of the thermistor is either 4.96 V or more, or 0.04 V or less
Conditions with the power on.
 J3 error is judged if the discharge pipe temperature is lower than the heat exchanger
temperature.
Possible Root  Disconnection of the connector for the thermistor

 Defective outdoor heat exchanger thermistor in the case of J3 error
Troubleshooting In case of P4 (Radiation fin thermistor)

Be sure to turn off the power switch before connecting or disconnecting connectors, or parts
may be damaged.
Caution Replace the outdoor unit PCB (main PCB)
Troubleshooting In case of H9
may be damaged.
Caution
Turn on the power again.
Error displayed No Reconnect the connectors

again on remote
or thermistors
controller?
Yes
Check the thermistor resistance value.
No Replace the defective

Normal?
thermistor(s) of the following
thermistors.
J3 error: the discharge • Outdoor temperature
pipe temperature is thermistors.
lower than the heat • Discharge pipe thermistor.
exchanger temperature. • Outdoor heat exchanger
Cooling : Outdoor heat thermistor.
exchanger
temperature.
Heating : Indoor heat
exchanger
temperature.
Yes

thermistor resistance value in the
heating operation.
Indoor heat
No Replace the indoor heat
exchanger thermistor
functioning? exchanger thermistor.
Yes
Replace the outdoor unit PCB.
H9 : Outdoor temperature thermistor

Outdoor H9 Indoor
Mode COOL Mode COOL
OutAir CHECK
Power
Fan-SP1
2020/06/22 16:45:01 60Hz EN03

Error Code J3
temperature.


may be damaged.
Troubleshooting In case of J3
may be damaged.
Caution

again on remote
or thermistors
controller?
Yes

Normal?
thermistors.
exchanger
temperature.
exchanger
temperature.
Yes

heating operation.
Indoor heat
Yes
J3 : Discharge pipe thermistor

Outdoor J3 Indoor
Mode COOL Mode COOL
INV
DiscTemp CHECK
EEV
2020/06/22 16:45:01 60Hz EN03

Error Code J6
temperature.


may be damaged.
Troubleshooting In case of J6
may be damaged.
Caution

again on remote
or thermistors
controller?
Yes

Normal?
thermistors.
exchanger
temperature.
exchanger
temperature.
Yes

heating operation.
Indoor heat
Yes
J6 : Outdoor heat exchanger thermistor

Outdoor J6 Indoor
Mode COOL Mode COOL
HeatExch CHECK
CTCurrent
INV-Temp
2020/06/22 16:45:01 60Hz EN03

Error Code P4
temperature.


may be damaged.
Troubleshooting In case of P4
may be damaged.
Caution

again on remote
or thermistors
controller?
Yes

Normal?
thermistors.
exchanger
temperature.
exchanger
temperature.
Yes

heating operation.
Indoor heat
Yes
P4 : Outdoor temperature thermistor

Outdoor P4 Indoor
Mode COOL Mode COOL
HeatExch
CTCurrent
INV-Temp
2020/06/22 16:45:01 60Hz EN03
4.23 Electrical Box Temperature Rise

Error Code L3
Method of Error An electrical box temperature rise is detected by checking the radiation fin thermistor with the
Detection compressor off.
Error Decision  With the compressor off, the radiation fin temperature is above A °C.
Conditions  The error is cleared when the radiation fin temperature drops below B °C.
 To cool the electrical components, the outdoor fan starts when the radiation fin temperature
rises above C °C and stops when the radiation fin temperature drops below B °C.
Model name A (°C) B (°C) C (°C)

(A)FTXC20/25/35 93 70 78
(A)FTXC50/60/71 100 64 91
Supposed  Defective outdoor fan motor

Causes  Short circuit
 Defective radiation fin thermistor
 Disconnection of connector
Troubleshooting
Turn off the power. Then, turn on WARNING
the power to restart the system. To cool the electrical components,
the outdoor fan starts when the
radiation fin temperature rises
above C °C. The outdoor fan stops
when the radiation fin temperature
Error again or outdoor YES drops below B °C.
fan activated?
Check the radiation fin

NO temperature.
NO
Above A°C? Replace the outdoor unit
PCB (main PCB).
YES
Check No. 19 NG
motor.
Correct the connectors
OK and fan motor lead wire.
PCB (main PCB).
NO
Radiation fin dirty? Check the installation
condition.
Go to Check No. 17.
YES
Clean up the radiation fin.
4.24 Radiation Fin Temperature Rise

Error Code L4
Method of Error A radiation fin temperature rise is detected by checking the radiation fin temperature with the
Detection compressor on.
Error Decision  The radiation fin temperature with the compressor on is above A °C.
Conditions  The error is cleared when the radiation fin temperature drops below B °C.
Model name A (°C) B (°C)

(A)FTXC20/25/35 93.0 78.0
(A)FTXC50/60/71 73.5 57.0
Supposed  Defective outdoor fan motor

Causes  Short circuit
 Defective radiation fin thermistor
 Disconnection of connector
 Silicone grease not applied properly on the radiation fin after replacing the outdoor unit PCB
Troubleshooting

YES Has the PCB been YES

Error displayed again? Check if silicone grease is
replaced?
applied properly on the
radiation fin. If not, apply
NO NO the silicone grease.
Check the radiation fin
temperature.
NO
Above A °C? Replace the outdoor unit
PCB (main PCB).
YES
Check No. 19 NG
motor.
Correct the connectors and
OK fan motor leads.
PCB (main PCB).
NO
Radiation fin dirty? Check the installation
condition.
Go to Check No. 17.
YES
Clean up the radiation fin.
Reference Refer to Silicone Grease on Power Transistor/Diode Bridge on page 108 for details.
4.25 Output Overcurrent Detection

Error Code L5
Description Output Overcurrent Detection
Method of Error An output overcurrent is detected by checking the current that flows in the inverter DC section.
Detection
Error Decision  A position signal error occurs while the compressor is running.
Conditions  A rotation speed error occurs while the compressor is running.
 An output overcurrent is fed from the output overcurrent detection circuit to the
microcomputer.
 If error repeats, the system is shut down.
 Reset condition: Continuous run for about 5 minutes without any other error.
Possible root  Poor installation condition

Causes  Closed stop valve
 Defective power module
 Wrong internal wiring
 Abnormal power supply voltage
 Power supply voltage out of installation
 Defective compressor
Troubleshooting
Check No. 17
Check the installation condition.
Stop valve fully open? NO Fully open the stop valve.
YES

See if the same error occurs.
Monitor the power supply

voltage, discharge and suction
Error again? NO pressures, and other factors
for a long term.
Possible causes
* Momentary drop of power Not a malfunction.
supply voltage Keep observing.
YES
* Compressor overload
* Short circuit Check the connectors and
other components.
Check No. 22
Check the power module.
Normal? NO
PCB (main PCB).
YES
NO
Voltage as rated? Correct the power supply.
YES
Short circuit of
wire breakage between NO
compressor’s coil Go to Check No. 18
phases?
YES
Replace the compressor.
4.26 Four Way Valve Abnormality

Remote EA
Controller
Display
Method of The indoor air temperature thermistor, the indoor unit heat exchanger thermistor, the outdoor
Malfunction temperature thermistor and the outdoor unit heat exchanger thermistor are checked to see if the
Detection function within their normal ranges in the operating mode.
Malfunction A following condition continues over 10 minute after operating 5 minutes.

Decision  Cooling / dry operation
Conditions (room temp. ˗ indoor heat exchanger temp.) < -5°C.
 Heating
(indoor unit heat exchanger temp. ˗ room temp.) < -5°C.
Supposed  Connector in poor contact

Causes  Thermistor defective
 Outdoor unit PCB defective
 Four way valve coil or harness defective
 Four way valve defective
 Foreign substance mixed in refrigerant
 Insufficient gas
Troubleshooting
Four way valve YES

coil disconnected Correct the four way
(loose)? valve coil.
NO
Harness YES Reconnect the

disconnected? harness.
NO
Check the continuity of the four

way valve coil and harness.
Disconnect the harness

from the connector.
Resistance
between NO
Replace the four way
harnesses about valve coil.
500-2300Ω
YES
Check No. 13 NG
Check the four way valve Replace the outdoor
switching output. unit PCB (main PCB).
OK
Any thermistor YES

Reconnect the
disconnected? thermistor(s).
NO
Check No. 01 NG
Check the thermistors. Replace the defective
thermistor(s).
OK
Check No. 14 NG
Check the refrigerant Refer to the refrigerant
line. *) Refrigerant shortage line check procedure.
*) Water mixed
*) Stop valve
OK
Replace the four way

valve (defective or
dust-clogged).
DAMA-SM-20-002 Actuator Check
5. Actuator Check
5.1 Thermistor Resistance Check
Check No.01 Measure the resistance of each thermistor using multimeter.
The resistance values are defined by below table.
If the measured resistance value does not match the listed value, the thermistor must be
replaced.
 Disconnect the connector of thermistor ASSY from the PCB to measure the resistance
between the pins using multimeter.
 To check the thermistor soldered on a PCB, disconnect the PCB from other PCB/parts, and
measure the resistance between the both ends of soldered thermistor.
Thermistor ASSY Soldered thermistor
Multimeter
Resistance range
Multimeter
Thermistor Type A Type B

temperature (°C) R(25°C) = 20 kΩ R(25°C) = 10 kΩ
-20 198 73
-15 149 57
-10 113 45
-5 86 35
0 66 28
5 51 23
10 40 18
15 32 15
20 25 12
25 20 10
30 16 8
35 13 7
40 11 6
45 9 5
50 7 4
Thermistor Resistance Type R(25°C)

Room temperature thermistor B 10 kΩ
Indoor Unit
Indoor heat exchanger thermistor B 10 kΩ
Outdoor temperature thermistor A 20 kΩ
Outdoor Unit Outdoor heat exchanger thermistor A 20 kΩ
Discharge pipe thermistor A 20 kΩ
Tolerance resistance type A : ±5%
Tolerance resistance type B : ±2%
Actuator Check DAMA-SM-20-002
5.2 Power Supply Waveform Check

Check No.11 Measure the power supply waveform between No. 1 and No. 2 on the terminal strip, and check
the waveform disturbance.
 Check if the power supply waveform is a sine wave (Fig.1).
 Check if there is waveform disturbance near the zero-cross (sections circled in Fig.2).
[Fig.1] [Fig.2]
5.3 Electronic Expansion Valve Check

Check No.12 Conduct the followings to check the electronic expansion valve (EV).
1. Check if the EV connector is correctly connected to the PCB.
2. Turn the power off and on again, and check if the EV generates a latching sound.
3. If the EV does not generate a latching sound in the step 2 above, disconnect the connector
and check the continuity using a multimeter.
4. Check the continuity between the pins 5 - 1, 5 - 2, 5 - 3, 5 - 4 (for 5P connectors) and
6 - 1, 6 - 2, 6 - 3, 6 - 4, 6 - 5, (for 6P connectors). If there is no continuity between the pins,
the EV coil is faulty.
5. If the continuity is confirmed in step 3, the outdoor unit PCB (main PCB) is faulty.
Harness 5P Harness 6P
5-1 6-1
5-2 6-2
S20 Check Check
5P Connector 5-3 6P Connector 6-3
5-4 6-4
1 2 3 4 5 1 2 3 4 5 6 6-5
RXC*BV1B
Class 20/25/35 50/60/71
EV connector P/N R04059047977 3P540612-1
Coil Model Name DPFX07-116 PQM10175
5P 5wires 6P 6wires
5.4 Four Way Valve Performance Check

Check No.13
Turn the power off and then on

again
* Four way valve coil Cooling / Dry /

Start heating operation Defrost: Not energized
Heating: energized
S80
voltage at 208 - 230 NO Replace the outdoor
VAC with compressor unit PCB (main PCB).
onΩ (Fig.1)
YES
Disconnect the four way valve coil

from the connector and check the
continuity
Four way
valve coil resistance at NO Replace the four way valve
500-2300Ω coil.
YES
Replace the four way valve.
(Fig.1)
Voltage at S80
208 - 230 VAC
Time
Compressor
ON

5.5 Inverter Unit Refrigerant System Check

Check No.14
Refrigerant system check
Is the discharge pipe YES

thermistor disconnected from Reconnect the thermistor.
the holder?
NO
Check for refrigerant leakage.
See the section on refrigerant
shortage detection.
Replace the refrigerant.
5.6 Rotation Pulse Check on the Outdoor Unit PCB

Check No.16 Make sure that the voltage of 320 ± V is applied.
1. Set operation OFF and power OFF. Disconnect the connector S71.
2. Check that the voltage between the pins 4 - 7 is 320 VDC.
3. Check that the control voltage between the pins 3 - 4 is 15 VDC.
4. Check that the rotation command voltage between the pins 2 - 4 is 0 ~ 6.5 VDC.
5. Keep operation OFF and power OFF. Connect the connector S71.
6. Check whether 4 pulses (0 ~ 15 VDC) are output at the pins 1 - 4 when the fan motor is
rotated 1 turn by hand.
When the fuse is melted, check the outdoor fan motor for proper function.
If NG in step 2 → Defective PCB → Replace the outdoor unit PCB (main PCB).
If NG in step 4 → Defective Hall IC → Replace the outdoor fan motor.
If OK in both steps 2 and 4 → Replace the outdoor unit PCB (main PCB).
PCB
S71
1 Actual rotation pulse input (0 ~ 15 VDC)
4 Rotation command voltage (0 ~ 6.5 VDC)
7 Control voltage 15 VDC
10
11
12
13 320 VDC
Applicable for (A)FTXC20/25/35/50/60/71

5.7 Installation Condition Check

Check No.17
Installation condition check
Check the allowable

dimensions of the air NG
suction and location or direction.
discharge area.
OK
Is the discharged air YES

short-circuited? location or direction.
NO
Is the outdoor heat YES

exchanger very dirty? Clean the outdoor heat
exchanger.
NO
Is the airflow blocked by NO

obstacles or winds Check the outdoor temperature.
blowing in the opposite (The outdoor temperature
direction? should be within the operation
range.)
YES
location or direction.
5.8 Discharge Pressure Check

Check No.18
Discharge pressure check
NO
Is the stop valve open? Open the stop valve.
YES
Is the connection pipe YES

Replace the pipe installed at
deformed? the site.
NO
Is the air filter or NO

indoor/outdoor heat Replace the compressor.
exchanger dirty?
YES
Clean the dirty air filter or
indoor/outdoor heat
exchanger.

5.9 Outdoor Fan System Check

Check No.19 DC motor

Check the outdoor fan system.
Is the NO Fan motor NO

outdoor fan running? lead wire connector Go to Check No. 16.
disconnected?
YES YES
Outdoor fan system is functioning. Reconnect the connector.
5.10 Main Circuit Short Check

Check No.20 Check to make sure that the voltage between (+) and (–) of the diode bridge (DB1) is
approximately 0 V before checking.
 Measure the resistance between the pins of the DB1 referring to the table below.
 If the resistance is ∞ or less than 1 kΩ, short circuit occurs on the main circuit.
Positive terminal (+) of
~ (2, 3) + (4) ~ (2, 3) – (1)
digital multimeter
Negative terminal (–) of + (4) ~ (2, 3) – (1) ~ (2, 3)
digital multimeter
Resistance is OK. several kΩ ~ several MΩ
Resistance is NG. 0 Ω or ∞
Diagram Main Circuit Short Check for A)FTXC20/25/35

Diagram Main Circuit Short Check for (A)FTXC50/60/71

5.11 Power Module Check

Check No.22 Check to make sure that the voltage between (+) and (–) of the power module is approximately
0 V before checking.
 Disconnect the compressor harness connector from the outdoor unit PCB. To disengage the
connector, press the protrusion on the connector.
 Follow the procedure below to measure resistance between the (+) or (–) terminal of the
power module and the U, V, or W terminal of the compressor with a multimeter. Evaluate the
measurement results referring to the following table.
Positive terminal (+) of Power module UVW Power module UVW
digital multimeter (+) (–)
Negative terminal (–) of UVW Power module UVW Power module
digital multimeter (+) (–)
Resistance is OK. several kΩ ~ several MΩ
Resistance is NG. 0 Ω or ∞
Diagram Power Module Check for (A)FTXC20/25/35
Diagram Power Module Check for (A)FTXC50/60/71

DAMA-SM-20-002
Part 6
Trial Operation and
Field Settings
1. Pump Down Operation........................................................................106
2. Forced Cooling Operation ...................................................................107
3. Silicone Grease on Power Transistor/Diode Bridge............................108
Part 6 Trial Operation and Field Settings 105

Pump Down Operation DAMA-SM-20-002
1. Pump Down Operation

Outline In order to protect the environment, be sure to conduct pump down operation when relocating or
disposing of the unit.
Details 1. Remove the valve caps from the liquid stop valve and the gas stop valve.
2. Carry out forced cooling operation.
3. After 5 to 10 minutes, close the liquid stop valve with a hexagonal wrench.
4. After 2 to 3 minutes, close the gas stop valve and stop the forced cooling operation.
Hexagonal
wrench
Close
Liquid stop valve
Gas stop valve Valve cap

Service port
Reference Refer to page 102 for forced cooling operation.
106 Trial Operation and Field Settings

DAMA-SM-20-002 Forced Cooling Operation
2. Forced Cooling Operation

Outline The forced cooling operation is allowed when both the following conditions are met.
1. The outdoor unit is not abnormal and not in the 3-minute standby mode.
2. The outdoor unit is not operating.
Protection functions have priority over all other functions during forced cooling operation.
Details  With indoor unit ON/OFF switch

Press indoor unit ON/OFF switch (SW1) for at least 5 seconds. The operation will start.
Forced cooling operation will stop automatically after about 15 minutes.
To stop the operation, press indoor unit ON/OFF switch.
ON/OFF
switch
Trial Operation and Field Settings 107

Silicone Grease on Power Transistor/Diode Bridge DAMA-SM-20-002
3. Silicone Grease on Power Transistor/Diode

Bridge
Outline Apply the specified silicone grease to the heat radiation part of a power transistor/diode bridge
when you replace an outdoor unit PCB. The silicone grease encourages the heat radiation of a
power transistor/diode bridge.
Details 1. Wipe off the old silicone grease completely.

2. Apply the silicone grease evenly. See the illustrations below for examples of application.
3. Tighten the screws of the power transistor/diode bridge.
4. Make sure that the heat radiation parts are firmly contacted to the radiation fin.
Note: Smoke emission may be caused by bad heat radiation when the silicone grease is not
appropriately applied.
 OK: Evenly applied

Power transistor
(or diode bridge)
PCB
Radiation
fin
Silicone grease
 NG: Not evenly applied
 NG: Foreign matter is stuck.
Foreign matter
108 Trial Operation and Field Settings

DAMA-SM-20-002
Part 7
Appendix
1. Piping Diagrams..................................................................................110
1.1 Indoor Unit............................................................................................110
1.2 Outdoor Unit .........................................................................................112
2. Wiring Diagrams..................................................................................114
2.1 Indoor Unit............................................................................................114
2.2 Outdoor Unit .........................................................................................115
3. Operation Limit....................................................................................119
4. Transmission Monitor [TM2016-1] Operation Instructions ..................120
4.1 Names and Functions of Parts .............................................................120
4.2 Basic Operations and Display ..............................................................121
109 Part 7 Appendix

DAMA-SM-20-002 Piping Diagrams
1. Piping Diagrams
1.1 Indoor Unit
Model: FTXC/ATXC20/25B
INDOOR UNIT
6. 4CuT HEAT EXCHANGER
THERMISTOR
ON HEAT EXCH.
CROSS FLOW FAN

FIELD PIPING
6. 4CuT
M
FAN MOTOR
FIELD PIPING
9. 5CuT 9. 5CuT
REFRIGERANT FLOW
COOLING
HEATING
Note: Dimension in mm
Model: FTXC/ATXC35B
INDOOR UNIT
HEAT EXCHANGER
6. 4CuT
CROSS FLOW FAN THERMISTOR

ON HEAT EXCH.
FIELD PIPING
6. 4CuT
M
FAN MOTOR
FIELD PIPING
9. 5CuT 9. 5CuT
REFRIGERANT FLOW
COOLING
HEATING
Appendix 110
Piping Diagrams DAMA-SM-20-002
Model: FTXC/ATXC50B
INDOOR UNIT
HEAT EXCHANGER
6. 4CuT
CROSS FLOW FAN THERMISTOR

ON HEAT EXCH.
FIELD PIPING
6. 4CuT
M
FAN MOTOR
FIELD PIPING
12. 7CuT 9. 5CuT
REFRIGERANT FLOW
COOLING
HEATING
Model: FTXC/ATXC60/71B
INDOOR UNIT
6. 4CuT
DISTRIBUTOR
HEAT EXCHANGER
THERMISTOR
CROSS FLOW FAN ON HEAT EXCH.
FIELD PIPING
6. 4CuT M
FAN MOTOR
HEADER
FIELD PIPING
12. 7CuT 12. 7CuT
REFRIGERANT FLOW
COOLING
HEATING
111 Appendix
DAMA-SM-20-002 Piping Diagrams
1.2 Outdoor Unit

Model: RXC/ARXC20/25/35B
OUTDOOR UNIT
HEAT EXCHANGER
7. 0CuT OUTDOOR AIR TEMPERATURE THERMISTOR
9. 5CuT
7. 0CuT
HEAT EXCHANGER THERMISTOR

MOTOR-OPERATED VALVE
7.0CuT 6. 4CuT 6. 4CuT
7.0CuT STRAINER
M
PROPELLER FAN
9. 5CuT
9. 5CuT
STRAINER
6. 4CuT
4-WAY VALVE
ON: HEATING
LIQUID STOP VALVE (6. 4CuT)

9. 5CuT
MUFFLER
DISCHARGE PIPE
THERMISTOR
6.4CuT
9. 5CuT 9. 5CuT
COMPRESSOR (9.5CuT)
ACCUMULATOR MUFFLER GAS STOP VALVE REFRIGERANT FLOW
COOLING
HEATING
Model: RXC/ARXC50/60B
OUTDOOR UNIT
7.0CuT HEAT EXCHANGER OUTDOOR TEMPERATURE THERMISTOR

9. 5CuT
7.0CuT
ELECTRONIC
EXPANSION
HEAT EXCHANGER THERMISTOR VALVE
6. 4CuT 9.52CuT 6. 4CuT EV
STRAINER
M
6. 4CuT
PROPELLER FAN
12.7CuT
STRAINER
6. 4Cut
FOUR WAY
12.7CuT
FIELD PIPING
9. 52CuT
VALVE
HEATING: ON (6. 4CuT)
LIQUID STOP
VALVE
DISCHARGE PIPE
THERMISTOR
MUFFLER
12.7CuT 12.7CuT FIELD PIPING
9.52Cut
COMPRESSOR (12.7CuT)
ACCUMULATOR MUFFLER MUFFLER GAS STOP
VALVE REFRIGERANT FLOW
COOLING
HEATING
Appendix 112
Piping Diagrams DAMA-SM-20-002
Model: RXC/ARXC71B
OUTDOOR UNIT
HEAT EXCHANGER OUTDOOR TEMPERATURE THERMISTOR

7. 0CuT
9. 5CuT
7. 0CuT
ELECTRONIC
EXPANSION
HEAT EXCHANGER THERMISTOR VALVE
EV
6. 4CuT 9.52CuT 6. 4CuT
STRAINER
6. 4CuT
M
PROPELLER FAN
STRAINER
12.7CuT
CAPILLARY TUBE
LIQUID RECEIVER
6. 4CuT
FOUR WAY
12.7CuT
VALVE
9. 52CuT
HEATING: ON
FIELD PIPING
DISCHARGE PIPE (6. 4CuT)
LIQUID STOP
THERMISTOR VALVE
MUFFLER
12.7CuT 12.7CuT FIELD PIPING
9.5Cut
COMPRESSOR (12.7CuT)
ACCUMULATOR MUFFLER MUFFLER MUFFLER GAS STOP
VALVE REFRIGERANT FLOW
COOLING
HEATING
113 Appendix
DAMA-SM-20-002 Wiring Diagrams
2. Wiring Diagrams
2.1 Indoor Unit
Model: FTXC/ATXC20/25/35B
TH1
DISPLAY BOARD
MF
250VAC T3.15A
EARTH
250VAC T3.15A
CN_DCFM
LIVE
TH2
CN_SW_LR
CN_DSP
NEUTRAL
CN_COIL
SIG CN_SW_UD MS1
CN_S21 CN_NS
G/Y
Z1C
C1 N=3
ORANGE
G/Y
BROWN
G/Y ORANGE WIFI

BLUE
ADAPTER
(OPTIONAL) WIRED
3 2 1 ACCESSORY
(OPTIONAL)
(OD UNIT)
NOTATION:
MF: FAN MOTOR
MS1: AIR SWING MOTOR (UP DOWN)
TH1: INDOOR COIL THERMISTOR
TH2: ROOM THERMISTOR
OD: OUTDOOR
----: FIELD WIRING
Z1C: FERRITE CORE
C1: CAPACITOR
Model: FTXC/ATXC50/60/71B
TH1
DISPLAY BOARD
MF
250VAC T3.15A
EARTH
CN_DCFM
250VAC T3.15A
LIVE
TH2
CN_SW_LR
CN_DSP
NEUTRAL
CN_COIL
SIG CN_SW_UD MS1
CN_S21 CN_NS
G/Y
ORANGE
G/Y
BROWN
WIFI
BLUE
ADAPTER
(OPTIONAL) WIRED
3 2 1 ACCESSORY
(OPTIONAL)
(OD UNIT)
NOTATION:
MF: FAN MOTOR
MS1: AIR SWING MOTOR (UP DOWN)
TH1: INDOOR COIL THERMISTOR
TH2: ROOM THERMISTOR
OD: OUTDOOR
----: FIELD WIRING
Appendix 114
Wiring Diagrams DAMA-SM-20-002
2.2 Outdoor Unit

HN1 E1
HL1
EXV
S
4WV
X12A
Z3C
S78 MF
E2
BLACK
WHITE
RED
U S79
V
W
1 2 3 S40 S90
TB L N
S80 S70 S20
REFER VIEW A
GREEN/YELLOW
POWER FROM OUTDOOR X11A Z1C

GREEN
GREEN RED (U)

L N 1 2 3
Z2C YELLOW (V)
MC
OLP
BLUE (W)
(POWER SUPPLY) (TO INDOOR UNIT)
VIEW A
DISCHARGE SENSOR
NOTATION:
MC: COMPRESSOR MOTOR HEAT EXCHANGER SENSOR
MF: FAN MOTOR
OLP: OVERLOAD PROTECTOR OUTDOOR AIR SENSOR
TB: TERMINAL BLOCK
EXV: ELECTRONIC EXPANSION VALVE COIL
X11A,X12A: CONNECTOR
Z1C,Z2C,Z3C: FERRITE CORE
4WV: FOUR WAY VALVE
-------: FIELD SUPPLY WIRING
115 Appendix
2.3 Printed Circuit Board Connector Wiring Diagram

Control PCB
(A1P) 1) S6 Connector for swing motor (horizontal blade)
2) S26 Connector for display/signal receiver PCB (A2P)
3) S32 Connector for indoor heat exchange thermistor (R2T)
4) S200 Connector for DC fan motor
5 S403 Connector for adaptor PCB (option)
6) H1, H2, H3 Connector for terminal strip
7) FG Connector for terminal strip (frame ground)
8) FU1 (F1U) Fuse (3.15 A, 250 V)
9) V2 (R2V) Varistor
Note The symbols in the parenthesis are the names on the appropriate wiring diagram.
Display/Signal
Receiver PCB 1) S27 Connector for control PCB (A1P)
(A2P) Indoor unit ON/OFF switch
2) SW1 (BS1) (Forced cooling operation ON/OFF switch)
* Refer to page 102 for detail of forced cooling operating.
3) LED1 (H1P) LED for operating (green)
4) LED2 (H2P) LED for timer (yellow)
5 RTH1 (R1T) Room temperature thermistor
Appendix 116
Wiring Diagrams DAMA-SM-20-002
2.4 Printed Circuit Board Connector Wiring Diagram

2.4.1 25/35 Class
Main PCB (A1P)
1) S20 Connector for electronic expansion valve coil
2) S30 Connector for compressor
3) S40 Connector for overload protector
5) S90 Connector for thermistors
(outdoor temperature, outdoor heat exchanger,
discharge pipe temperature)
6) HL1, HN1, S Connector for terminal strip
7) E1, E2 Terminals for earth wire
8) HR1, HR2 Connector for reactor
9) FU2 (F2U) Fuse (3.15 A, 250 V)
10) FU3 (F3U) Fuse (20 A, 250 V)
11) LED A LED for service monitor (green)
12) V2 (R2V), Varistor
V3 (R3V)
117 Appendix
2.4.2 50 Class
Main PCB (A1P)
1) S20 Connector for electronic expansion valve coil
2) S40 Connector for overload protector
Connector for thermistors
4) S90 (outdoor temperature, outdoor heat exchanger,
discharge pipe temperature)
5 HL1, HN1, S Connector for terminal strip
6) E1, E2 Terminals for earth wire
7) U, V, W Connector for compressor
8) FU1 (F1U), Fuse (3.15 A, 250 V)
FU2 (F2U)
9) FU3 (F3U) Fuse (30 A, 250 V)
10) LED A LED for service monitor (green)
11) V1 (R1V), Varistor
V2 (R2V),
V3 (R3V)
Appendix 118
Operation Limit DAMA-SM-20-002
3. Operation Limit
119 Appendix
DAMA-SM-20-002 Transmission Monitor [TM2016-1] Operation Instructions
4. Transmission Monitor [TM2016-1] Operation

Instructions
4.1 Names and Functions of Parts
4.1.1 LCD Screen display
(1) Outdoor unit error code display (red, yellow, none)

(2) Indoor unit error code display (red, yellow, none)
(3) Outdoor unit data (fixed display)
(4) Indoor unit data (fixed display)
(5) Outdoor unit data (variable display)
(6) Indoor unit data (variable display)
(7) SD card remaining recording time
(d: day; h: hour; m: minute; s: second)
(8) Name of data recording file on SD card
(9) Current time
(10)Power supply frequency, software version (50Hz/60Hz)
EN**: English
CN**: Chinese
(simplified Chinese characters)
CT**: Chinese
(traditional Chinese characters)
SP**: Spanish
** : Version Number
4.1.2 LED indications
LED Description Detail

Lights in normal condition; flashes when transmission
ERR Green Indicates system status
error occurs or transmission is unconfirmed
Indicates the status of communication Lights when data is being recorded; flashes when
REC Red
data recording and functions accessing SD card
Indicates the communication status of
IN Yellow Flashes when indoor unit is in transmission operation
indoor unit.
Indicates the communication status of
OUT Blue Flashes when outdoor unit is in transmission operation
outdoor unit.
Appendix 120
Transmission Monitor [TM2016-1] Operation Instructions DAMA-SM-20-002
4.2 Basic Operations and Display

4.2.1 Power ON/OFF
When the connection cable is connected to the air conditioner indoor-outdoor unit connection cable (L/N/S)
and the air conditioner is turned ON, the transmission monitor turns ON. When the air conditioner is turned
OFF, the transmission monitor also turns OFF.
4.2.2 Selection of operation mode

Operation mod is determined according to the statuses of the SEL SW and REC SW at the time of
power ON.
SEL SW REC SW Operation mode Description of operation

Release Release Normal monitoring mode Displays communication data on the LCD screen.
Automatically updates the program in the SYSTEM
Press Press Software update mode
folder on the SD card. (Refer to section 3-7)
4.2.3 Selection of display screen

Each time the SEL SW is pressed, the cursor moves in the following order:
Outdoor unit data indoor unit data Data recording file Current time.
The jog dial is used for the following operations: scrolling of the screen at the cursor position, selection
of data recording file, and setting of current date/time.
Page 1 (Outdoor) Page 1 (Indoor) Page 2 (Outdoor) Page 1 (Indoor)
Page Outdoor Indoor

INV SuctTemp
1 DiscTemp EvaTemp1
EEV Fan1SP
HeatExch
2 CTCurrent Not Applicable
INV-Temp
OutAir
3 Power Not Applicable
Fan-SP1
Page 3 (Outdoor) Page 1 (Indoor)
121 Appendix
Warning z Daikin products are manufactured for export to numerous countries throughout the world. Prior to
purchase, please confirm with your local authorized importer, distributor and/or retailer whether this
product conforms to the applicable standards, and is suitable for use, in the region where the product
will be used. This statement does not purport to exclude, restrict or modify the application of any local
legislation.
z Ask a qualified installer or contractor to install this product. Do not try to install the product yourself.
Improper installation can result in water or refrigerant leakage, electrical shock, fire or explosion.
z Use only those parts and accessories supplied or specified by Daikin. Ask a qualified installer or
contractor to install those parts and accessories. Use of unauthorized parts and accessories or
Service Manual / Inverter Split Wall Mounted Type (A)FTXC Series

improper installation of parts and accessories can result in water or refrigerant leakage, electrical
shock, fire or explosion.
z Read the user's manual carefully before using this product. The user's manual provides important
safety instructions and warnings. Be sure to follow these instructions and warnings.
If you have any inquiries, please contact your local importer, distributor and/or retailer.
Cautions on product corrosion

1. Air conditioners should not be installed in areas where corrosive gases, such as acid gas or alkaline gas, are produced.
2. If the outdoor unit is to be installed close to the sea shore, direct exposure to the sea breeze should be avoided. If you need to install
the outdoor unit close to the sea shore, contact your local distributor.
Lot 60334, Persiaran Bukit Rahman Putra 3,

Taman Perindustrian Bukit Rahman Putra,
DAMA-SM-20-002
47000 Sungai Buloh, Selangor Darul Ehsan,

Malaysia.
http://www.daikin.com/products/ac/
© All rights reserved
zSpecifications, designs and other content appearing in this brochure are current as of January 2019 but subject to change without notice.
DAMA-SM-20-002
11/2020 AK.B

Daikin RXC-B (R32) Manual Service

Uploaded by

Copyright:

Available Formats

Daikin RXC-B (R32) Manual Service

Uploaded by

Document Information

Original Description:

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Daikin RXC-B (R32) Manual Service

Uploaded by

Copyright:

Available Formats

DAMA-SM-20-002

Service Manual / Inverter Split Wall Mounted Type (A)FTXC Series

Part 1 General Information .......................................................... 12

Part 3 Functions and Control ....................................................... 27

Part 4 Remote Controller ............................................................. 54

Part 5 Service Diagnosis .............................................................. 57

Part 6 Trial Operation and Field Settings .................................. 105

Part 7 Appendix .......................................................................... 109

iii Table of Contents

1.1 Warnings and Cautions Regarding Safety of Workers

Be sure to disconnect the power cable from the socket before

When disconnecting the suction or discharge pipe of the

Be sure to discharge the capacitor completely before conducting

Be sure to wear a safety helmet, gloves, and a safety belt when

In case of R-32 refrigerant models, be sure to use pipes, flare nuts

Do not clean the air conditioner with water.

Be sure to provide an earth / grounding when repairing the

Be sure to conduct repair work with appropriate tools.

Be sure to check that the refrigerating cycle section has cooled

Conduct welding work in a well-ventilated place.

 General working area

 Checking for presence of refrigerant

 Fire extinguishing equipment

 Checking the refrigeration equipment

Safety Checklist (con't)

 Repairs to sealed components

 Repair to intrinsically safe components

Safety Checklist (con't)

 Removal and evacuation

Safety Checklist (con't)

1.2 Warnings and Cautions Regarding Safety of Users

Do not use a joined power cable or extension cable, or share the

Be sure to use an exclusive power circuit for the equipment, and

Do not damage or modify the power cable.

When replacing the coin battery in the remote controller, be sure to

Do not install the equipment in a place where there is a possibility of

Check to see if parts and wires are mounted and connected

Check the earth / grounding, and repair it if the equipment is not

Be sure to measure insulation resistance after the repair, and make

Do not tilt the unit when removing it.

12 Part 1 General Information

Item Non-inverter air conditioner Inverter air conditioner

<Block diagram of inverter>

3. Names and Functions of Inverter Components

<Schematic view of inverter main circuit configuration>

 5HDFWRU  3RZHUPRGXOH ,30

Model Name and Power Supply

Indoor Unit Outdoor Unit Power Supply

F : Air-Cooled Split Indoor Unit, DAIKIN Brand

System X : Inverter, Heatpump

Refrigerant & Grade C : R32 , Standard

Capacity Indication* 20 : 2.0 kW

Major Design Change B : B Series

Power Supply V1 : 1Phase / 220V-240V / 50Hz

A : Air-Cooled Split Indoor Unit, DAIKIN Brand

Refrigerant & Grade C : R32 , Standard

Capacity Indication* 20 : 2.0 kW

Major Design Category B : B Series

Power Supply V1 : 1Phase / 220V-240V / 50Hz

5HDFWRU 3RZHUPRGXOH ,30