Determination of The Earth's Magnetic Field: (Item No.: P2430100)

Student's
Sheet
Printed: 18.08.2017 16:52:39 | P2430100
Determination of the earth's magnetic field

(Item No.: P2430100)
Curricular Relevance
Topic: Subtopic: Experiment:

Area of Expertise: Education Level:
Electricity and Magnetic Field and Determination of the
Physics University
Magnetism Magnetic Forces earth's magnetic field
Difficulty Preparation Time Execution Time Recommended Group Size
Difficult 1 Hour 2 Hours 2 Students
Additional Requirements: Experiment Variations:
Keywords:
magnetic inclination, magnetic declination, isoclinic lines, isogonic lines, inclinometer, magnetic flow density, Helmholtz coils
Overview
Short description
A constant magnetic field, its magnitude and direction known, is superimposed on the unknown earth-magnetic field. The earth-
magnetic field can then be calculated from the magnitude and direction of the resulting flux density.
Fig. 1: Experimental set-up to determine the earth’s magnetic field.
Robert-Bosch-Breite 10 Tel: +49 551 604 - 0 [email protected]

D - 37079 Göttingen Fax: +49 551 604 - 107 www.phywe.com
Student's Sheet
Printed: 18.08.2017 16:52:39 | P2430100
Equipment
Position No. Material Order No. Quantity

1 Helmholtz coils, one pair 06960-00 1
2 PHYWE power supply, universal DC: 0...18 V, 0...5 A / AC: 2/4/6/8/10/12/15 V, 5 A 13504-93 1
3 Rheostat, 100 Ohm , 1.8A 06114-02 1
4 Teslameter, digital 13610-93 1
5 Hall probe, axial 13610-01 1
6 Digital multimeter 2005 07129-00 1
7 Magnetometer 06355-00 1
8 Barrel base PHYWE 02006-55 1
9 Right angle clamp expert 02054-00 1
10 Support rod, stainless steel, l = 250 mm, d = 10 mm 02031-00 1
11 Stand tube 02060-00 1
12 Connecting cord, 32 A, 1000 mm, red 07363-01 1
13 Connecting cord, 32 A, 1000 mm, blue 07363-04 4
Tasks
1. The magnetic flux of pair of Helmholtz coils is to be determined and plotted graphically as a function of the coil current.
The Helmholtz system calibration factor is calculated from the slope of the line.
2. The horizontal component of the earth-magnetic field is determined through superimposition of the Helmholtz field.
3. The angle of inclination must be determined in order to calculate the vertical component of the earth-magnetic field.

Student's Sheet
Printed: 18.08.2017 16:52:39 | P2430100
Set-up and procedure

The experiment composition is as depicted in Fig. 1. The Helmholtz coils, complete with mounted space-holders, are connected
in series (linkage of equally-numbered connections) and connected with the DC generator by the rheostat and the multimeter
used as ammeter. The Hall probe is to be fixed on the support rod with barrel base pointing inward toward the coil axis in the
center of the Helmholtz arrangement. In this arrangement, the horizontal flux density of the pair of coils is to be
determined as a function of the coil current . The calibration factor is determined through the appertaining
graphic representation. (See Fig. 2).
Fig. 2: Calibration function of the pair of Helmholtz

coils.
Note:
Before measuring begins, the zero-point position of the teslameter must be set precisely.
By means of barrel base, stand tube and optic judgement, the magnetometer (with a leveled graduated circle) is placed between
the coils so that the center of the graduated circle is approximately identical with the center of the pair of coils.
First, the direction “north/south” is noted on the graduated circle for currentless coils. In order to secure the direction
“north/south” of the magnetic needle, the needle should be slightly turned away from its resting position several times. Possible
friction resistance can be reduced by gently tapping the instrument. In order to determine the horizontal component of the
earth-magnetic field, the deflection angle of the magnetic needle is measured from its resting position as a function of small
coil currents. If the polarity of the coil current is reversed, the measuring series must be repeated. In determining the exact
angle, the indications from both needle tips must be considered.
The angle (Fig. 3A) between the direction “north/south” and the axis of the pair of coils is obtained through maximal needle
deflection when the resistor is short-circuited the ammeter eliminated and the coil current set to approximately 4 A.
In conclusion, and for currentless coils, the graduated circle of the magnetometer is turned to the vertical plane so that the
magnetic needle now indicates the inclination angle . Make sure that the spin axis is consistent with the direction
“north/south”. In order to check on , the magnetometer is turned by 180° and thus replaced on the vertical plane.

Student's Sheet
Printed: 18.08.2017 16:52:39 | P2430100
Fig. 3: Vector diagram of the magnetic flux densities: A)

horizontal plane, B) vertical plane.

Student's Sheet
Printed: 18.08.2017 16:52:39 | P2430100
Theory and evaluation

For currentless coils, the magnetic needle of the magnetometer alligns itself with the horizontal component (direction
"north/south") of the earth-magnetic field. If an additional magnetic field is superimposed on this component through the
Helmholtz coils, the needle will be turned around the angle and will point in the direction of the resulting . In Fig. 3A), the
field components for the general case are represented. The components drawn by a broken line represent the resulting
conditions of the polarity of the coil current is reversed.
By means of the sine-theorem, we obtain:
(1)
In the special case where the coil axis is perpendicular to the direction “north/south” , the following applies:
(2)
By means of the calibration
(see Fig. 2) (3)
we get from (1):
(4)
If is represented as a function of (Fig. 4), the horizontal component of the earth-magnetic field is obtained from the
slope.
Fig. 4: Linear function according to (4) to determine the

horizontal component h E of the magnetic flux density
of the earth-magnetic field.
From Fig. 3 B) follows the vertical component and the measured angle of inclination.
µ (5)
The total flow density is calculated to
(6)
µ
Reference values for Göttingen, Germany:
µ
Student's Sheet
Printed: 18.08.2017 16:52:39 | P2430100

Note
Acceptable measuring results are only obtainable if the influence of perturbing magnetic fields (for example: pieces of iron close
to the measuring site) is avoided.
Abbreviations
horizontal flux density in the center of the Helmholtz arrangement (external field)
horizontal component of the earth-magnetic field
resulting flux density
vertical component of the earth-magnetic field
Helmholtz coil current
calibration factor


Determination of The Earth's Magnetic Field: (Item No.: P2430100)

Uploaded by

Copyright:

Available Formats

Determination of The Earth's Magnetic Field: (Item No.: P2430100)

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Determination of The Earth's Magnetic Field: (Item No.: P2430100)

Uploaded by

Copyright:

Available Formats

Student's

Determination of the earth's magnetic field

Topic: Subtopic: Experiment:

Difficulty Preparation Time Execution Time Recommended Group Size

Difficult 1 Hour 2 Hours 2 Students

Additional Requirements: Experiment Variations:

Fig. 1: Experimental set-up to determine the earth’s magnetic field.

Robert-Bosch-Breite 10 Tel: +49 551 604 - 0 [email protected]

Position No. Material Order No. Quantity

Robert-Bosch-Breite 10 Tel: +49 551 604 - 0 [email protected]

Set-up and procedure

Fig. 2: Calibration function of the pair of Helmholtz

Robert-Bosch-Breite 10 Tel: +49 551 604 - 0 [email protected]

Fig. 3: Vector diagram of the magnetic flux densities: A)

Robert-Bosch-Breite 10 Tel: +49 551 604 - 0 [email protected]

Theory and evaluation

By means of the sine-theorem, we obtain:

By means of the calibration

(see Fig. 2) (3)

we get from (1):

Fig. 4: Linear function according to (4) to determine the

The total flow density is calculated to

Reference values for Göttingen, Germany:

Robert-Bosch-Breite 10 Tel: +49 551 604 - 0 [email protected]

You might also like