The initial on-orbit checkout of the soft X-ray spectroscopic system on board the XRISM satellite is summarized. The satellite was launched on September 6, 2023 (UT) and has been undergoing initial checkout since then. Immediately after the launch, the cryocoolers were turned on and their operation was established. The first cycle of the adiabatic demagnetization refrigerator was performed on Oct. 9th, 2023, to transition the sensor to steady-state operational temperature conditions. Subsequently, the filter wheel, which supports energy calibration, was started up. The energy scale is highly sensitive to the temperature environment around the sensor and its analog electronics. The gain correction was established by referring to the calibration X-ray line. For an optimization of the cooler frequencies, we took data including the noise spectra by scanning the cooler frequencies, and selected a good frequency pair in the on-orbit environment. At the last stage of the checkout, the gate valve, which protects the inside of the Dewar from outside air pressure at launch, was attempted to be opened to bring the system to a state where it is ready for regular operations but was failed.
We present the design and performance of the XRISM Soft X-Ray Spectrometer Resolve, successfully launched on a JAXA H-IIA rocket September 7, 2023. The instrument uses a 36-pixel array of microcalorimeters at the focus of a grazing-incidence x-ray mirror. The instrument has achieved an energy resolution of 4.5 eV (FWHM) at 6. The overall cooling chain was designed to provide a lifetime of at least 3 years in orbit and operate without liquid helium to provide redundancy and the longest operational lifetime for the instrument. Early indications that the cryogen lifetime will exceed 4 years. X-rays are focused onto the array with a high-throughput grazing incidence X-ray Mirror Assembly with over 200 nested two-stage X-ray reflectors. A series of onboard X-ray calibrations sources allow simultaneous energy scale calibration lines simultaneously while observing celestial sources. The inflight performance of Resolve will be described along with a summary of the scientific capabilities.
The number of magnetospheric solar wind charge exchange (SWCX) soft X-ray events detectable with GEO-X was estimated using the latest calibrated ACE/SWICS data on solar wind O7+ ions. The OVII line flux at a certain solar wind O7+ flux was calculated from an magnetohydrodynamic simulation of 2001 March 31 geomagnetic storm and scaled to the sum of emission lines from other solar wind ions based on Suzaku magnetospheric SWCX events. The instrumental background including radiation noise mainly due to energetic protons was estimated using GOES >10 MeV proton flux and our previously developed GEANT4 simulation. The number of detectable magnetospheric SWCX events that meet a criterion of signal-to-noise ratios grater than 20 peaks near solar maximum, reaching 49.7 events per year with an average duration of 2.94 hours. Assuming an observation efficiency of 30%, we found that at least one event can be detected within a 4-month time frame with a 90% probability.
Resolve is the instrument that utilizes an X-ray micro-calorimeter array onboard the XRISM (X-Ray Imaging and Spectroscopy Mission), which was launched on September 6 (UT), 2023. It fully met the spectral performance requirement (7 eV at 6 keV) both on the ground and in orbit and was confirmed to have the same performance as the SXS onboard the ASTRO-H (Hitomi) satellite. The detectors are operated at a low temperature of 50 mK to achieve the required energy resolution with the cooling system to satisfy the lifetime requirement of over 3 years. The cooling system is equipped with a 3-stage ADR and superfluid liquid He (LHe) as the heat sink for the ADR. The Joule-Thomson cooler unit and 2-stage Stirling cooler units are adopted to reduce heat load to the LHe. In the pre-launch operations, we carried out the low-temperature LHe top-off operation. The resultant amount of liquid He was over 35 L at the launch, which is sufficient to meet the lifetime requirement. During the post-launch operation, the LHe vent valve was opened five minutes after launch during the rocket acceleration, and the cryocoolers started in several revolutions as planned which established stable cooling of the dewar.
We have been developing an optical blocking filter for GEO-X which will perform soft X-ray imaging spectroscopy of Earth’s magnetosphere. GEO-X will provide an unprecedented view through X-ray observations in terms of the interaction between solar wind and magnetosphere. GEO-X consists of MEMS X-ray mirrors and a focal plane CMOS detector which is sensitive to visible photons necessitating a thin-film optical blocking filter to attenuate noise from out-of-band photons while providing high transmittance for in-band soft X-ray photons. The OBF design for GEO-X spans an aluminum 40 mm x 40 mm aperture with 200 nm polyimide and 150 nm aluminum. A square-celled stainless steel mesh with a grid size of 3 mm and a width of 200 um provides mechanical support against launch stresses. The material combination provides high transmittance across the GEO-X bandpass and tolerances for severe launch and space environments at the same time. We conducted performance tests for the EM coupons. We confirmed the pinhole frequency of the aluminum film is very small (visible transmittance < 1e-8). It is found that film uniformity is very good, varying by 1% in polyimide and 2% in aluminum thicknesses over the 20 mm x 20 mm scan region at 277, 380, 522, and 776 eV. Before and after the UV irradiation test (50 ESD), no significant differences in terms of the pinhole frequency are found. Additionally, there are no significant descrepancies in the size of the pinholes for all of the pinholes we investigated before and after the high-speed atomic oxygen irradiation test with a fluence value of 1019 atoms cm−2 even though additional pinholes were detected after the test possibly due to accelerated metal outgassing contaminants remaining the vacuum chamber.
GEO-X (GEOspace X-ray imager) is a small satellite mission to visualize the Earth’s magnetosphere through Solar Wind Charge eXchange (SWCX). SWCX is known as soft X-ray emissions generated by the charge exchange between highly charged-state heavy ions and neutral atoms in the Earth’s exosphere. The GEO-X satellite is aimed to be launched during the upcoming solar maximum around 2025-2027 and is planned to be injected to a low-latitude orbit which allows visualization of the magnetosphere from outside the magnetosphere. The satellite will carry a light-weight X-ray imaging spectrometer, dramatically improving the size and weight of those onboard past X-ray astronomy satellites.
We have been developing ultra-lightweight Wolter type-I X-ray telescopes fabricated with MEMS technologies for GEO-X (GEOspace X-ray imager) which is a small satellite mission to perform soft X-ray imaging spectroscopy of the entire Earth’s magnetosphere. The telescope is our original type of micropore optics and possesses lightness (∼5 g), a short focal length (∼250 mm), and a wide field of view (∼5° × ∼5°). The MEMS X-ray telescope is made of 4-inch Si (111) wafers. The Si wafer is first processed by deep reactive ion etching, which has numerous curvilinear micropores (a 20-μm width) whose sidewalls are utilized as X-ray reflective mirrors. High-temperature hydrogen annealing and chemical mechanical polishing processes are applied to make those sidewalls smooth and flat enough to reflect X-rays. After that, the wafer is plastic-deformed into a spherical shape and Pt-coated by a plasma atomic layer deposition process to focus X-rays with high reflectivity. Finally, we assemble two optics bent with different curvatures (1000- and 333-mm radii) and complete the Wolter type-I telescope. We optimized each process and conducted an X-ray irradiation test to assemble the full-processed optics into an EM telescope for the GEO-X mission, which enabled to complete the telescope to achieve an angular resolution of ∼4.8 arcmin in FWHM in the assembled telescope. We report on our latest development status and the X-ray imaging performance of the GEO-X EM telescope.
Lobster eye optics are expected as to be a wide-field telescope and are suitable for future X-ray sky surveys and monitoring missions. The ultra-lightweight X-ray optics have been developed using MEMS technologies and the same way can be applied to the fabrication of lobster eye optics. A large number of slits with 20 micro-meters width were formed by an etching process in a 4-inch Si wafer with 300 micro-meters thickness. To collect X-rays on a focal plane, the wafer was plastic-deformed into a spherical shape with a radius of curvature of 1000 mm. Two deformed wafers were assembled in such a way as to arrange the slits of each wafer orthogonally. Then, samples of lobster eye optics were completed and the fabrication process flow with MEMS technologies can be confirmed.
The X-Ray Imaging and Spectroscopy Mission (XRISM) project at JAXA officially started in 2018. Following the development of onboard components, the proto-flight test was conducted from 2021 to 2023 at JAXA Tsukuba Space Center. The spacecraft was launched from JAXA Tanegashima Space Center on September 7, 2023 (JST), and onboard components, including the science instruments, were activated during the in-orbit commissioning phase. Following the previous report in 2020, we report the spacecraft ground tests, the launch operation, in-orbit operations, and the status and plan of initial and subsequent guest observations.
We report a development status of a focal plane detector for the GEO-X (GEOspace X-ray imager) mission that will perform soft X-ray (≤2 keV) imaging spectroscopy of Earth’s magnetosphere from a micro satellite. The mission instrument consists of a microelectromechanical systems (MEMS) X-ray mirror and a focal plane detector. A sensor with fine positional resolution and moderate energy resolution in the energy band of 0.3 to 2 keV is required. Because the observing target is the magnetosphere around the day-side Earth, the visible-light background must be decreased by shortening the integration time for readout. To satisfy the above requirements, a high-speed X-ray CMOS sensor is being evaluated as a primary candidate for the detector. Irradiating the flight candidate sensor with monochromatic X-rays, we obtained the energy resolution of 205 eV (FWHM) at 6 keV by cooling the devices to −15°C. Radiation tolerance of the sensor, especially in terms of total dose effect, is investigated with 100 MeV proton. The amount of degradation of energy resolution is <50 eV up to 10 krad, which ensures that we will be able to track and calibrate the change of the line width in orbit.
GEOspace X-ray imager (GEO-X) is a small satellite mission aiming at visualization of the Earth’s magnetosphere by X-rays and revealing dynamic couplings between solar wind and the magnetosphere. In-situ spacecraft have revealed various phenomena in the magnetosphere. X-ray astronomy satellite observations recently discovered soft X-ray emissions originating from the magnetosphere. We are developing GEO-X by integrating innovative technologies of a wide field of view (FOV) X-ray instrument and a small satellite for deep space exploration. The satellite combines a Cubesat and a hybrid kick motor, which can produce a large delta v to increase the altitude of the orbit to about 30 to 60 RE from a relatively low-altitude (e.g., geo transfer orbit) piggyback launch. GEO-X carries a wide FOV (5 × 5 deg) and a good spatial resolution (10 arcmin) X-ray (0.3 to 2 keV) imaging spectrometer using a micro-machined X-ray telescope and a CMOS detector system combined with an optical blocking filter. We aim to launch the satellite around the solar maximum of solar cycle 25.
We have been developing silicon foil X-ray optics using a hot plastic deformation process for future astronomical observations. Our foil mirror is made of a 0.3-mm thick silicon wafer and is plastically deformed into a high-accurate conical shape with a curvature radius of ~100 mm. The angular resolution we evaluated using a test sample mirror was ~32 arcseconds in the best region. We have also successfully coated a platinum film on the foil mirror using the atomic layer deposition process. In this talk, we report on the fabrication method and the X-ray imaging capability of our silicon foil X-ray optics.
We have been developing an ultra-lightweight Wolter type-I X-ray telescope fabricated with micro electro mechanical systems (MEMS) technologies for GEO-X (GEOspace X-ray Imager) mission.
GEO-X will aim global imaging of the Earth's magnetosphere using X-rays.
The telescope is our original micropore optics which is light in weight (~5 g), compact with a short focal length (~250 mm), and has a wide field-of-view (~5 deg x 5 deg).
In this talk we show developed assembly processes to meet the requirements of the GEO-X mission and the telescope's X-ray imaging performance as an engineering model with this method.
The resolve instrument onboard the X-Ray Imaging and Spectroscopy Mission (XRISM) consists of an array of 6 × 6 silicon-thermistor microcalorimeters cooled down to 50 mK and a high-throughput x-ray mirror assembly (XMA) with a focal length of 5.6 m. XRISM is a recovery mission of ASTRO-H/Hitomi, and the Resolve instrument is a rebuild of the ASTRO-H soft x-ray spectrometer (SXS) and the Soft X-ray Telescope (SXT) that achieved energy resolution of ∼5 eV FWHM on orbit, with several important changes based on lessons learned from ASTRO-H. The flight models of the Dewar and the electronics boxes were fabricated and the instrument test and calibration were conducted in 2021. By tuning the cryocooler frequencies, energy resolution better than 4.9 eV FWHM at 6 keV was demonstrated for all 36 pixels and high resolution grade events, as well as energy-scale accuracy better than 2 eV up to 30 keV. The immunity of the detectors to microvibration, electrical conduction, and radiation was evaluated. The instrument was delivered to the spacecraft system in 2022-04 and is under the spacecraft system testing as of writing. The XMA was tested and calibrated separately. Its angular resolution is 1.27′ and the effective area of the mirror itself is 570 cm2 at 1 keV and 424 cm2 at 6 keV. We report the design and the major changes from the ASTRO-H SXS, the integration, and the results of the instrument test.
We have been developing an ultra-lightweight Wolter type-I x-ray telescope fabricated with MEMS technologies for GEO-X (geospace x-ray imager) which is an 18U CubeSat (∼20 kg) to perform soft x-ray imaging spectroscopy of the entire Earth’s magnetosphere from Earth orbit near the moon. The telescope is our original micropore optics which possesses lightness (∼15 g), a short focal length (∼250 mm), and a wide field of view (∼5 ◦ × ∼5 ◦ ). The MEMS x-ray telescope is made of 4-inch Si (111) wafers. The Si wafer is firstly processed by deep reactive ion etching such that they have numerous curvilinear micropores (20-µm width) whose sidewalls are utilized as X-ray reflective mirrors. High-temperature hydrogen annealing and chemical mechanical polishing processes are then applied to make those sidewalls smooth and flat enough to reflect X-rays. After that, the wafer is plastic-deformed into a spherical shape and Pt-coated by plasma atomic layer deposition (ALD) process to focus x-rays with high reflectivity. Finally, we assemble two optics bent with different curvatures (1000- and 333-mm radius) into the Wolter type-I telescope. Optimizing the annealing and polishing processes, we found that the optic achieves an angular resolution of ∼5.4 arcmins in HPW. This is comparable with the requirement for GEO-X (∼5 arcmins in HPD at single reflection). Our optic was also successfully Pt-coated by a plasma-enhanced ALD process to enhance x-ray reflectivity. Moreover, we fabricated an STM telescope and confirmed its environmental tolerances by conducting an acoustic test with the H-IIA rocket qualification test level and a radiation tolerance test with a 100 MeV proton beam for 30 krad equivalent to a 3-year duration in the GEO-X orbit.
We are developing an x-ray CMOS detector for the GEO-X (GEOspace x-ray imager) mission that will perform soft x-ray (≤2 keV) imaging spectroscopy of Earth’s magnetosphere using a micro satellite. The mission instrument consists of a MEMS x-ray mirror and a focal plane detector. For the latter, we need a sensor with fine positional resolution and moderate energy resolution in the energy band of 0.3 to 2 keV. Because we observe the day-side structure of the earth’s magnetosphere, visible-light background must be decreased by shortening the integration time for readout. To satisfy the above requirements, a high-speed x-ray CMOS sensor is being evaluated as a primary candidate for the detector. We adopt back-side illuminated sensors that have been originally developed for visible-light or UV imaging. The sensors have different specification in terms of the thickness of epitaxial wafer and specific resistance. Irradiating sensors with monochromatic x-rays from 55Fe, we obtained the energy resolution of 205 and 227 eV (FWHM) depending on the sensor type for single pixel events at 6 keV by cooling down the sensor to −15°C. On the other hand, we found that the pulse height of the events whose charges spread over multiple pixels are significantly lower than that of single pixel events in some chips. Then we selected the chips that shows better charge collection efficiency as flight candidate. Radiation tolerance of the sensor, especially in terms of total dose effect, is investigated with 100 MeV proton. The amount of dose ranges up to 100 krad depending on position in the sensor. In spite of the excessive dose compared with 10 krad/yr in the expected highly elliptical orbit, Mn Kα and Kβ are well resolved. The amount of degradation of energy resolution is less than 50 eV up to 10 krad, which ensures that we will be able to track and calibrate the change of the line width in orbit We also utilize multi-color x-rays to investigate spectroscopic performance in the energy band of 0.5 to 7 keV. Multiple lines below 1 keV are resolved and energy resolutions are evaluated as well as linearity performance.
We are developing a novel Bragg reflection x-ray polarimeter using hot plastic deformation of silicon wafers. A Bragg reflection polarimeter has the advantage of simple principle and large modulation factor but suffers from the disadvantage of a narrow detectable energy band and difficulty to focus an incident beam. We overcome these disadvantages by bending a silicon wafer at high temperature. The bent Bragg reflection polarimeter have a wide energy band using different angles on the wafer and enable focusing. We have succeeded in measuring x-ray polarization with this method for the first time using a sample optic made from a 4-inch silicon (100) wafer.
GEO-X (GEOspace X-ray imager) is a small satellite mission aiming at visualization of the Earth’s magnetosphere by X-rays and revealing dynamical couplings between solar wind and magnetosphere. In-situ spacecraft have revealed various phenomena in the magnetosphere. In recent years, X-ray astronomy satellite observations discovered soft X-ray emission originated from the magnetosphere. We therefore develop GEO-X by integrating innovative technologies of the wide FOV X-ray instrument and the microsatellite technology for deep space exploration. GEO-X is a 50 kg class microsatellite carrying a novel compact X-ray imaging spectrometer payload. The microsatellite having a large delta v (<700 m/s) to increase an altitude at 40-60 RE from relatively lowaltitude (e.g., Geo Transfer Orbit) piggyback launch is necessary. We thus combine a 18U Cubesat with the hybrid kick motor composed of liquid N2O and polyethylene. We also develop a wide FOV (5×5 deg) and a good spatial resolution (10 arcmin) X-ray (0.3-2 keV) imager. We utilize a micromachined X-ray telescope, and a CMOS detector system with an optical blocking filter. We aim to launch the satellite around the 25th solar maximum.
GEO-X is a small satellite mission in near moon orbit to visualize the Earth’s magnetosphere. Since the Earth is a bright x-ray source, its x-rays have a potentially effect on the GEO-X observations. Fluxes of the unexpected x-rays, stray lights, and of the GEO-X signal can be estimated. In order to estimate the stray light effect on the GEO-X FOV, we carried out a ray-tracing simulation and calculated the signal-to-noise ratio for elongations from the Earth. The S/N ratio shows a range depending on signal flux. The signal estimated by MHD simulations is smaller than estimation based on the typical observation. When we apply the small signal flux, the S/N ratio is <10 at 7 deg elongation of the GEO-X FOV from the Earth in an orbital altitude of 60RE. In order to improve the S/N ratio, there are two ways, installing a collimator in front of the optics and adjusting the observation position to obtain a large elongation. The ray-tracing simulation reveals that the collimator with 30 µm pore width and 300 µm thickness can improve the S/N ratio. The S/N ratio with the collimator can achieve >10 when the elongation is 7 deg in the orbital altitude of 60 RE. A sample collimator was fabricated by a Si dry etching. Difference of the pore width from the designed value was occurred. Since the difference can lead to extra photon loss, a trade-off study between fabrication precision and observation position is important.
We report development status of an X-ray imaging spectrometer for scientific micro satellite mission GEO-X that aims for imaging of Earth’s magnetosphere from the vicinity of the Moon (∼40 RE). The planned direction for the observations includes proximity of the day-side Earth. Therefore the primary requirement for the detector is the fast frame rate to decrease the visible light background. In this regard we will apply complementary MOS (CMOS) sensor that is originally fabricated for the visible light and/or infrared spectroscopy. Faster readout speed improves time resolution and decrease the contribution from visible light compared with the conventional CCD detectors. We evaluate imaging and spectroscopic performances of backside illumination type scientific CMOS sensors with low noise performance. Most of the signals produced by X-rays distributes within 2 by 2 pixels. Spectra of monochromatic X-rays exhibit significant difference of pulse height between the event within single pixel and that spreads across multiple pixels, which indicates that a part of the signal charges are lost around the pixel edges. Then we adopt another type of the sensor that have been updated in terms of the incident surface treatment. We found that the amount of the lost charges are substantially decreased with the new sensor. Another measure to improve the spectroscopic performance is the dark level determination. Gradual or discontinuous change of the dark level in orbit might it difficult to evaluate the appropriate dark level especially for the high frame rate and the limited resources of onboard computer. Then we take the average of pulse heights for the outermost pixels in a event (5 by 5 pixels) and correct the pulse height of all pixels with the average value. With these measures the energy resolution improved successfully.
GEO-X (GEOspace X-ray imager) is a 50 kg-class small satellite to image the global Earth’s magnetosphere in X-rays via solar wind charge exchange emission. A 12U CubeSat will be injected into an elliptical orbit with an apogee distance of ∼40 Earth radii. In order to observe the diffuse soft X-ray emission in 0.3-2 keV and to verify X-ray imaging of the dayside structures of the magnetosphere such as cusps, magnetosheaths and magnetopauses which are identified statistically by in-situ satellite observations, an original light-weight X-ray imaging spectrometer (∼10 kg, ∼10 W, ∼10×10×30 cm) will be carried. The payload is composed of a ultra light-weight MEMS Wolter type-I telescope (∼4×4 deg2 FOV, <10 arcmin resolution) and a high speed CMOS sensor with a thin optical blocking filter (∼2×2 cm2 , frame rate ∼20 ms, energy resolution <80 eV FWHM at 0.6 keV). An aimed launch year is 2023-25 corresponding to the 25th solar maximum.
The X-Ray Imaging and Spectroscopy Mission (XRISM) is the successor to the 2016 Hitomi mission that ended prematurely. Like Hitomi, the primary science goals are to examine astrophysical problems with precise highresolution X-ray spectroscopy. XRISM promises to discover new horizons in X-ray astronomy. XRISM carries a 6 x 6 pixelized X-ray micro-calorimeter on the focal plane of an X-ray mirror assembly and a co-aligned X-ray CCD camera that covers the same energy band over a large field of view. XRISM utilizes Hitomi heritage, but all designs were reviewed. The attitude and orbit control system were improved in hardware and software. The number of star sensors were increased from two to three to improve coverage and robustness in onboard attitude determination and to obtain a wider field of view sun sensor. The fault detection, isolation, and reconfiguration (FDIR) system was carefully examined and reconfigured. Together with a planned increase of ground support stations, the survivability of the spacecraft is significantly improved.
The source position determination method of the multiplexing lobster-eye optics (MuLE), which is a newly proposed configuration of the Lobster-Eye (LE) optics to reduce the number of focal plane detectors significantly, was developed. In the MuLE configuration, X-rays came from different field-of-views (FoVs) were focused on a single imager. To separate the multiplexed FoVs, the optics was designed so that cross-like responses of LE mirror in different FoVs had different azimuthal rotation angles. In this paper, we show the method to determine the rotation angles and verify the FoV discrimination power by using a ray tracing simulation. The configuration we assumed in the simulation was nine multiplexed FoVs projecting onto a single imager (nine-segment MuLE optics) with a 30 cm focal length and a 9×9 cm2 effective area of each LE segment. One LE segment covers 9.6°× 9.6° FoV and the total FoV of the nine-segment MuLE configuration was 9 times of that. Our method provided 100% correct FoV discrimination at the 5σ detection limit flux (35–70 mCrab) for a transient source with a duration of 100 s except for the edge of the FoV.
We propose a concept of multiplexing lobster-eye (MuLE) optics to achieve significant reductions in the number of focal plane imagers in lobster-eye (LE) wide-field x-ray monitors. In the MuLE configuration, an LE mirror is divided into several segments and the x-rays reflected on each of these segments are focused on a single image sensor in a multiplexed configuration. If each LE segment assumes a different rotation angle, the azimuthal rotation angle of a cross-like image reconstructed from a point source by the LE optics identifies the specific segment that focuses the x-rays on the imager. With a focal length of 30 cm and LE segments with areas of 10 × 10 cm2, ∼1 sr of the sky can be covered with 36 LE segments and only four imagers (with total areas of 10 × 10 cm2). A ray tracing simulation was performed to evaluate the nine-segment MuLE configuration. The simulation showed that the flux (0.5 to 2 keV) associated with the 5σ detection limit was ∼2 × 10 − 10 erg cm − 2 s − 1 (10 mCrab) for a transient with a duration of 100 s. The simulation also showed that the direction of the transient for flux in the range of 14 to 17 mCrab at 0.6 keV was determined correctly with a 99.7% confidence limit. We conclude that the MuLE configuration can become an effective on-board device for small satellites for future x-ray wide-field transient monitoring.
Toward an era of x-ray astronomy, next-generation x-ray optics are indispensable. To meet a demand for telescopes lighter than the foil optics but with a better angular resolution <1 arcmin, we are developing micropore x-ray optics based on micromaching technologies. Using sidewalls of micropores through a thin silicon wafer, this type can be the lightest x-ray telescope ever achieved. Two Japanese missions, ORBIS and GEO-X, will carry this telescope. ORBIS is a small x-ray astronomy mission to monitor supermassive blackholes, while GEO-X is a small exploration mission of the Earth’s magnetosphere. Both missions need an ultralightweight (<1 kg) telescope with moderately good angular resolution (<10 arcmin) at an extremely short focal length (<30 cm). We plan to demonstrate this type of telescope in these two missions around 2020.
The Resolve instrument onboard the X-ray Astronomy Recovery Mission (XARM) consists of
an array of 6x6 silicon-thermistor microcalorimeters cooled down to 50 mK
and a high-throughput X-ray mirror assembly with a focal length of 5.6 m.
The XARM is a recovery mission of ASTRO-H/Hitomi,
and is developed by international collaboration of Japan, USA, and Europe.
The Soft X-ray Spectrometer (SXS) onboard Hitomi demonstrated high resolution
X-ray spectroscopy of ~ 5 eV FWHM in orbit for most of the microcalorimeter pixels.
The Resolve instrument is planned to mostly be a copy of the Hitomi SXS and
Soft X-ray Telescope designs, though several changes are planned
based on the lessons learned of Hitomi.
The energy resolution budget of the microcalorimeters is updated,
reflecting the Hitomi SXS results.
We report the current status of the Resolve instrument.
The ASTRO-H mission was designed and developed through an international collaboration of JAXA, NASA, ESA, and the CSA. It was successfully launched on February 17, 2016, and then named Hitomi. During the in-orbit verification phase, the on-board observational instruments functioned as expected. The intricate coolant and refrigeration systems for soft X-ray spectrometer (SXS, a quantum micro-calorimeter) and soft X-ray imager (SXI, an X-ray CCD) also functioned as expected. However, on March 26, 2016, operations were prematurely terminated by a series of abnormal events and mishaps triggered by the attitude control system. These errors led to a fatal event: the loss of the solar panels on the Hitomi mission. The X-ray Astronomy Recovery Mission (or, XARM) is proposed to regain the key scientific advances anticipated by the international collaboration behind Hitomi. XARM will recover this science in the shortest time possible by focusing on one of the main science goals of Hitomi,“Resolving astrophysical problems by precise high-resolution X-ray spectroscopy”.1 This decision was reached after evaluating the performance of the instruments aboard Hitomi and the mission’s initial scientific results, and considering the landscape of planned international X-ray astrophysics missions in 2020’s and 2030’s. Hitomi opened the door to high-resolution spectroscopy in the X-ray universe. It revealed a number of discrepancies between new observational results and prior theoretical predictions. Yet, the resolution pioneered by Hitomi is also the key to answering these and other fundamental questions. The high spectral resolution realized by XARM will not offer mere refinements; rather, it will enable qualitative leaps in astrophysics and plasma physics. XARM has therefore been given a broad scientific charge: “Revealing material circulation and energy transfer in cosmic plasmas and elucidating evolution of cosmic structures and objects”. To fulfill this charge, four categories of science objectives that were defined for Hitomi will also be pursued by XARM; these include (1) Structure formation of the Universe and evolution of clusters of galaxies; (2) Circulation history of baryonic matters in the Universe; (3) Transport and circulation of energy in the Universe; (4) New science with unprecedented high resolution X-ray spectroscopy. In order to achieve these scientific objectives, XARM will carry a 6 × 6 pixelized X-ray micro-calorimeter on the focal plane of an X-ray mirror assembly, and an aligned X-ray CCD camera covering the same energy band and a wider field of view. This paper introduces the science objectives, mission concept, and observing plan of XARM.
Toward a new era of X-ray astronomy, next generation X-ray optics are indispensable. To meet a demand for telescopes lighter than the foil optics but with a better angular resolution less than 1 arcmin, we are developing micropore X-ray optics based on micromaching technologies. Using sidewalls of micropores through a thin silicon wafer, this type can be the lightest X-ray telescope ever achieved. Two new Japanese missions ORBIS and GEOX will carry this optics. ORBIS is a small X-ray astronomy mission to monitor supermassive blackholes, while GEO-X is a small exploration mission of the Earth’s magnetosphere. Both missions need a ultra light-weight (<1 kg) telescope with moderately good angular resolution (<10 arcmin) at an extremely short focal length (<30 cm). We plan to demonstrate this optics in these two missions around 2020, aiming at future other astronomy and exploration missions.
The Hitomi (ASTRO-H) mission is the sixth Japanese x-ray astronomy satellite developed by a large international collaboration, including Japan, USA, Canada, and Europe. The mission aimed to provide the highest energy resolution ever achieved at E > 2 keV, using a microcalorimeter instrument, and to cover a wide energy range spanning four decades in energy from soft x-rays to gamma rays. After a successful launch on February 17, 2016, the spacecraft lost its function on March 26, 2016, but the commissioning phase for about a month provided valuable information on the onboard instruments and the spacecraft system, including astrophysical results obtained from first light observations. The paper describes the Hitomi (ASTRO-H) mission, its capabilities, the initial operation, and the instruments/spacecraft performances confirmed during the commissioning operations for about a month.
The soft x-ray spectrometer (SXS) was a cryogenic high-resolution x-ray spectrometer onboard the Hitomi (ASTRO-H) satellite that achieved energy resolution of 5 eV at 6 keV, by operating the detector array at 50 mK using an adiabatic demagnetization refrigerator (ADR). The cooling chain from room temperature to the ADR heat sink was composed of two-stage Stirling cryocoolers, a He4 Joule–Thomson cryocooler, and superfluid liquid helium and was installed in a dewar. It was designed to achieve a helium lifetime of more than 3 years with a minimum of 30 L. The satellite was launched on February 17, 2016, and the SXS worked perfectly in orbit, until March 26 when the satellite lost its function. It was demonstrated that the heat load on the helium tank was about 0.7 mW, which would have satisfied the lifetime requirement. This paper describes the design, results of ground performance tests, prelaunch operations, and initial operation and performance in orbit of the flight dewar and the cryocoolers.
We summarize all of the in-orbit operations of the soft x-ray spectrometer (SXS) onboard the ASTRO-H (Hitomi) satellite. The satellite was launched on February 17, 2016, and the communication with the satellite ceased on March 26, 2016. The SXS was still in the commissioning phase, in which the set-ups were progressively changed. This paper is intended to serve as a concise reference of the events in orbit in order to properly interpret the SXS data taken during its short lifetime and as a test case for planning the in-orbit operation for future microcalorimeter missions.
When using superfluid helium in low-gravity environments, porous plug phase separators are commonly used to vent boil-off gas while confining the bulk liquid to the tank. Invariably, there is a flow of superfluid film from the perimeter of the porous plug down the vent line. For the soft x-ray spectrometer onboard ASTRO-H (Hitomi), its approximately 30-liter helium supply has a lifetime requirement of more than 3 years. A nominal vent rate is estimated as ∼30 μg/s, equivalent to ∼0.7 mW heat load. It is, therefore, critical to suppress any film flow whose evaporation would not provide direct cooling of the remaining liquid helium. That is, the porous plug vent system must be designed to both minimize film flow and to ensure maximum extraction of latent heat from the film. The design goal for Hitomi is to reduce the film flow losses to <2 μg/s, corresponding to a loss of cooling capacity of <40 μW. The design adopts the same general design as implemented for Astro-E and E2, using a vent system composed of a porous plug, combined with an orifice, a heat exchanger, and knife-edge devices. Design, on-ground testing results, and in-orbit performance are described.
The soft x-ray spectrometer (SXS) onboard the Hitomi satellite achieved a high-energy resolution of ∼4.9 eV at 6 keV with an x-ray microcalorimeter array cooled to 50 mK. The cooling system utilizes liquid helium, confined in zero gravity by means of a porous plug (PP) phase separator. For the PP to function, the helium temperature must be kept lower than the λ point of 2.17 K in orbit. To determine the maximum allowable helium temperature at launch, taking into account the uncertainties in both the final ground operations and initial operation in orbit, we constructed a thermal mathematical model of the SXS dewar and PP vent and carried out time-series thermal simulations. Based on the results, the maximum allowable helium temperature at launch was set at 1.7 K. We also conducted a transient thermal calculation using the actual temperatures at launch as initial conditions to determine flow and cooling rates in orbit. From this, the equilibrium helium mass flow rate was estimated to be ∼34 to 42 μg/s, and the lifetime of the helium mode was predicted to be ∼3.9 to 4.7 years. This paper describes the thermal model and presents simulation results and comparisons with temperatures measured in the orbit.
KEYWORDS: X-rays, Sensors, Spectroscopy, Space operations, Lithium, Field effect transistors, Satellites, Calibration, Single crystal X-ray diffraction, Magnetic sensors
We present the overall design and performance of the Astro-H (Hitomi) Soft X-Ray Spectrometer (SXS). The instrument uses a 36-pixel array of x-ray microcalorimeters at the focus of a grazing-incidence x-ray mirror Soft X-Ray Telescope (SXT) for high-resolution spectroscopy of celestial x-ray sources. The instrument was designed to achieve an energy resolution better than 7 eV over the 0.3-12 keV energy range and operate for more than 3 years in orbit. The actual energy resolution of the instrument is 4-5 eV as demonstrated during extensive ground testing prior to launch and in orbit. The measured mass flow rate of the liquid helium cryogen and initial fill level at launch predict a lifetime of more than 4 years assuming steady mechanical cooler performance. Cryogen-free operation was successfully demonstrated prior to launch. The successful operation of the SXS in orbit, including the first observations of the velocity structure of the Perseus cluster of galaxies, demonstrates the viability and power of this technology as a tool for astrophysics.
The Hitomi (ASTRO-H) mission is the sixth Japanese X-ray astronomy satellite developed by a large international collaboration, including Japan, USA, Canada, and Europe. The mission aimed to provide the highest energy resolution ever achieved at E > 2 keV, using a microcalorimeter instrument, and to cover a wide energy range spanning four decades in energy from soft X-rays to gamma-rays. After a successful launch on 2016 February 17, the spacecraft lost its function on 2016 March 26, but the commissioning phase for about a month provided valuable information on the on-board instruments and the spacecraft system, including astrophysical results obtained from first light observations. The paper describes the Hitomi (ASTRO-H) mission, its capabilities, the initial operation, and the instruments/spacecraft performances confirmed during the commissioning operations for about a month.
The Soft X-ray Spectrometer (SXS) is a cryogenic high-resolution X-ray spectrometer onboard the ASTRO-H satellite, that achieves energy resolution better than 7 eV at 6 keV, by operating the detector array at 50 mK using an adiabatic demagnetization refrigerator. The cooling chain from room temperature to the ADR heat sink is composed of 2-stage Stirling cryocoolers, a 4He Joule-Thomson cryocooler, and super uid liquid He, and is installed in a dewar. It is designed to achieve a helium lifetime of more than 3 years with a minimum of 30 liters. The satellite was launched on 2016 February 17, and the SXS worked perfectly in orbit, until March 26 when the satellite lost its function. It was demonstrated that the heat load on the He tank was about 0.7 mW, which would have satisfied the lifetime requirement. This paper describes the design, results of ground performance tests, prelaunch operations, and initial operation and performance in orbit of the flight dewar and cryocoolers.
The Soft X-ray Spectrometer (SXS) onboard ASTRO-H (Hitomi) achieved a high energy resolution of ~ 4.9 eV at 6 keV with an X-ray microcalorimeter array kept at 50 mK in the orbit. The cooling system utilizes liquid helium, and a porous plug phase separator is utilized to confine it. Therefore, it is required to keep the helium temperature always lower than the λ point of 2.17 K in the orbit. To clarify the maximum allowable helium temperature at the launch also considering the uncertainties of the initial operation in the orbit, we constructed a thermal mathematical model of the SXS dewar which properly implements the helium mass flow rate through the porous plug, and carried out time-series thermal simulations. Based on the results, the maximum allowable helium temperature at the launch was set at 1.7 K. We also conducted a transient thermal calculation using the actual temperatures at the launch as initial conditions. As a result, the helium mass flow rate when the helium temperature was in equilibrium is estimated to be 34–42 μg/s, and the life time of the helium mode is predicted to be ~ 3.9–4.7 years. The present paper reports model structures, simulation results, and the comparisons with temperatures measured in the orbit.
Suppression of super fluid helium flow is critical for the Soft X-ray Spectrometer onboard ASTRO-H (Hitomi). In nominal operation, a small helium gas flow of ~30 μg/s must be safely vented and a super fluid film flow must be sufficiently small <2 μg/s. To achieve a life time of the liquid helium, a porous plug phase separator and a film flow suppression system composed of an orifice, a heat exchanger, and knife edge devices are employed. In this paper, design, on-ground testing results and in-orbit performance of the porous plug and the film flow suppression system are described.
We summarize all the in-orbit operations of the Soft X-ray Spectrometer (SXS) onboard the ASTRO-H (Hit- omi) satellite. The satellite was launched on 2016/02/17 and the communication with the satellite ceased on 2016/03/26. The SXS was still in the commissioning phase, in which the setups were progressively changed. This article is intended to serve as a reference of the events in the orbit to properly interpret the SXS data taken during its short life time, and as a test case for planning the in-orbit operation for future micro-calorimeter missions.
We present the development status of the Soft X-ray Spectrometer (SXS) onboard the ASTRO-H mission. The SXS provides the capability of high energy-resolution X-ray spectroscopy of a FWHM energy resolution of < 7eV in the energy range of 0.3 – 10 keV. It utilizes an X-ray micorcalorimeter array operated at 50 mK. The SXS microcalorimeter subsystem is being developed in an EM-FM approach. The EM SXS cryostat was developed and fully tested and, although the design was generally confirmed, several anomalies and problems were found. Among them is the interference of the detector with the micro-vibrations from the mechanical coolers, which is the most difficult one to solve. We have pursued three different countermeasures and two of them seem to be effective. So far we have obtained energy resolutions satisfying the requirement with the FM cryostat.
The joint JAXA/NASA ASTRO-H mission is the sixth in a series of highly successful X-ray missions developed by the Institute of Space and Astronautical Science (ISAS), with a planned launch in 2015. The ASTRO-H mission is equipped with a suite of sensitive instruments with the highest energy resolution ever achieved at E > 3 keV and a wide energy range spanning four decades in energy from soft X-rays to gamma-rays. The simultaneous broad band pass, coupled with the high spectral resolution of ΔE ≤ 7 eV of the micro-calorimeter, will enable a wide variety of important science themes to be pursued. ASTRO-H is expected to provide breakthrough results in scientific areas as diverse as the large-scale structure of the Universe and its evolution, the behavior of matter in the gravitational strong field regime, the physical conditions in sites of cosmic-ray acceleration, and the distribution of dark matter in galaxy clusters at different redshifts.
We propose a new high contrast imager for Kyoto 4m segmented telescope called SEICA (Second-generation
Exoplanet Imager with Coronagraphic Adaptive optics), aiming at detection and characterization of selfluminous
gas giants within 10AU around nearby stars. SEICA is aggressively optimized for high performance
at very small inner working angle, 10-6 detection contrast at 0".1 in 1-hour integration. We start the on-sky
commissioning test in 2016 and the science observations in 2017. Since it is the first time to realize the highcontrast
imaging on the segmented telescope, SEICA is an important step toward future high contrast
sciences on Extremely Large Telescopes (ELTs). This paper presents an overall of the SEICA program and
the conceptual design for ultimate performance under given atmospheric conditions.
The Soft X-ray Spectrometer (SXS) is a cryogenic high resolution X-ray spectrometer onboard the X-ray astronomy
satellite ASTRO-H. The detector array is cooled down to 50 mK using a 3-stage adiabatic demagnetization
refrigerator (ADR). The cooling chain from room temperature to the ADR heat-sink is composed of superfluid
liquid He, a 4He Joule-Thomson cryocooler, and 2-stage Stirling cryocoolers. It is designed to keep 30 L of liquid
He for more than 3 years in the nominal case. It is also designed with redundant subsystems throughout from
room temperature to the ADR heat-sink, to alleviate failure of a single cryocooler or loss of liquid He.
Our recent development of transition-edge sensor (TES) microcalorimeters for future X-ray astronomical missions
such as DIOS is reported. In-house micromaching processes has been established aiming at prompt fabrication
of TES devices. With a single-pixel TES microcalorimeter and an Au absorber, the energy resolution of 4.8 eV
at 5.9 keV is achieved. 16×16 pixel arrays of TES microcalorimeters are successfully fabricated by using deep
dry etching technique. The energy resolution is 11 eV and 26 eV with and without an Au absorber, respectively.
The worse energy resolution than a single-pixel TES is due to large decrease of TES sensitivity and increase
of transition temperature after etching. The reason for these phenomena is under investigation. In parallel,
mushroom-type Au absorber structures are being tested. Furthermore, to precisely measure TES sensitivities
and heat capacity, an experimental setup for impedance measurements is established.
We present the current status of a small X-ray mission DIOS (Diffuse Intergalactic Oxygen Surveyor), consisting
of a 4-stage X-ray telescope and an array of TES microcalorimeters, cooled with mechanical coolers, with a total
weight of about 400 kg. The mission will perform survey observations of warm-hot intergalactic medium using
OVII and OVIII emission lines, with the energy coverage up to 1.5 keV. The wide field of view of about 50'
diameter, superior energy resolution close to 2 eV FWHM, and very low background will together enable us a
wide range of science for diffuse X-ray sources. We briefly describe the current status of the development of the
satellite, and the subsystems.
Access to the requested content is limited to institutions that have purchased or subscribe to SPIE eBooks.
You are receiving this notice because your organization may not have SPIE eBooks access.*
*Shibboleth/Open Athens users─please
sign in
to access your institution's subscriptions.
To obtain this item, you may purchase the complete book in print or electronic format on
SPIE.org.
INSTITUTIONAL Select your institution to access the SPIE Digital Library.
PERSONAL Sign in with your SPIE account to access your personal subscriptions or to use specific features such as save to my library, sign up for alerts, save searches, etc.