Scribd
Upload
239 views21 pages

FM CH 1

This document provides an overview of key concepts in fluid mechanics, including: 1) It defines properties of fluids like density, specific gravity, viscosity, vapor pressure and compressibility. Viscosity represents a fluid's resistance to flow while compressibility measures its change in volume with pressure. 2) It describes surface tension and capillary effects, where molecules closer to the surface experience unbalanced attractive forces, causing liquids to take spherical shapes and rise in thin tubes. 3) Key terms are introduced like saturation temperature/pressure, vapor pressure, and partial pressures in mixtures. Liquids change phase at their saturation temperature and pressure.

Uploaded by

Siddharth Gupta
Copyright
© Attribution Non-Commercial (BY-NC)
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PPT, PDF, TXT or read online on Scribd
239 views21 pages

FM CH 1

This document provides an overview of key concepts in fluid mechanics, including: 1) It defines properties of fluids like density, specific gravity, viscosity, vapor pressure and compressibility. Viscosity represents a fluid's resistance to flow while compressibility measures its change in volume with pressure. 2) It describes surface tension and capillary effects, where molecules closer to the surface experience unbalanced attractive forces, causing liquids to take spherical shapes and rise in thin tubes. 3) Key terms are introduced like saturation temperature/pressure, vapor pressure, and partial pressures in mixtures. Liquids change phase at their saturation temperature and pressure.

Uploaded by

Siddharth Gupta
Copyright
© Attribution Non-Commercial (BY-NC)
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PPT, PDF, TXT or read online on Scribd
You are on page 1/ 21

FLUID MECHANICS

CHAPTER 1 (PROPERTIES OF FLUIDS )

OBJECTIVES
Have a working knowledge of the basic properties of

fluids and understand the continuum approximation.


Have a working knowledge of viscosity and the

consequences of the frictional effects it causes in fluid flow.


Calculate the capillary rise (or drop) in tubes due to the

surface tension effect.

INTRODUCTION
Property: Any characteristic of a system.

Some familiar properties are pressure P, temperature T,

volume V, and mass m. Properties are considered to be either intensive or extensive. Intensive properties: Those that are independent of the mass of a system, such as temperature, pressure, and density. Extensive properties: Those whose values depend on the sizeor extentof the system. Specific properties: Extensive properties per unit mass.

DENSITY AND SPECIFIC GRAVITY


Density

SPECIFIC GRAVITY
Specific gravity: The ratio of the density of a substance to

the density of some standard substance at a specified temperature (usually water at 4C)

SPECIFIC WEIGHT
Specific weight: The weight of a unit volume of a

substance.

VISCOSITY
Viscosity: A property that represents the internal

resistance of a fluid to motion or the fluidity.


Drag force: The force a flowing fluid exerts on a body in

the flow direction. The magnitude of this force depends, in part, on viscosity.
The viscosity of a fluid is a measure of its resistance to

deformation. Viscosity is due to the internal frictional force that develops between different layers of fluids as they are forced to move relative to each other

VISCOSITY

A fluid moving relative to a body exerts a drag force on the body, partly because of friction caused by viscosity.

Newtonian fluids: Fluids for which the rate of deformation is proportional to the shear stress.

Shear stress
The behavior of a fluid in laminar flow between two parallel plates when the upper plate moves with a constant velocity.

Shear force

coefficient of viscosity
Dynamic (absolute) viscosity kg/m s or N s/m2 or Pa s 1 poise = 0.1 Pa s

10

The rate of deformation (velocity gradient) of a Newtonian fluid is proportional to shear stress, and the constant of proportionality is the viscosity.

Variation of shear stress with the rate of deformation for Newtonian and non-Newtonian fluids (the slope of a curve at a point is the apparent viscosity of the fluid at that point).

11

Kinematic viscosity m2/s or stoke 1 stoke = 1 cm2/s


For liquids, both the dynamic and kinematic viscosities are practically independent of pressure, and any small variation with pressure is usually disregarded, except at extremely high pressures.

For gases, this is also the case for dynamic viscosity (at low to moderate pressures), but not for kinematic viscosity since the density of a gas is proportional to its pressure.

For gases: For liquids

Dynamic viscosity, in general, does not depend on pressure, but kinematic viscosity does.

12

The viscosity of a fluid is directly related to the pumping power needed to transport a fluid in a pipe or to move a body through a fluid. Viscosity is caused by the cohesive forces between the molecules in liquids and by the molecular collisions in gases, and it varies greatly with temperature. In a liquid, the molecules possess more energy at higher temperatures, and they can oppose the large cohesive intermolecular forces more strongly. As a result, the energized liquid molecules can move more freely. In a gas, the intermolecular forces are negligible, and the gas molecules at high temperatures move randomly at higher velocities. This results in more molecular collisions per unit volume per unit time and therefore in greater resistance to flow.

The viscosity of liquids decreases and the viscosity of gases increases with temperature.

13

length of the cylinder

number of revolutions per unit time

This equation can be used to calculate the viscosity of a fluid by measuring torque at a specified angular velocity. Therefore, two concentric cylinders can be used as a viscometer, a device that measures viscosity.

27 SURFACE TENSION AND CAPILLARY EFFECT


Liquid droplets behave like small balloons filled with the liquid on a solid surface, and the surface of the liquid acts like a stretched elastic membrane under tension. The pulling force that causes this tension acts parallel to the surface and is due to the attractive forces between the molecules of the liquid. The magnitude of this force per unit length is called surface tension (or coefficient of surface tension) and is usually expressed in the unit N/m. This effect is also called surface energy [per unit area] and is expressed in the equivalent unit of N m/m2.

14

Some consequences of surface tension.

15

Attractive forces acting on a liquid molecule at the surface and deep inside the liquid. Stretching a liquid film with a Ushaped wire, and the forces acting on the movable wire of length b.

Surface tension: The work done per unit increase in the surface area of the liquid.

16

The free-body diagram of half a droplet or air bubble and half a soap bubble.

17

Capillary effect: The rise or fall of a liquid in a small-diameter tube inserted into the liquid. Capillaries: Such narrow tubes or confined flow channels. The capillary effect is partially responsible for the rise of water to the top of tall trees. Meniscus: The curved free surface of a liquid in a capillary tube. The strength of the capillary effect is quantified by the contact (or wetting) angle, defined as the angle that the tangent to the liquid surface makes with the solid surface at the point of contact.

Capillary Effect

The contact angle for wetting and nonwetting fluids.

The meniscus of colored water in a 4-mm-inner-diameter glass tube. Note that the edge of the meniscus meets the wall of the capillary tube at a very small contact angle.

18

The capillary rise of water and the capillary fall of mercury in a smalldiameter glass tube.

The forces acting on a liquid column that has risen in a tube due to the capillary effect.

Capillary rise is inversely proportional to the radius of the tube and density of the liquid.

19

23 VAPOR PRESSURE AND CAVITATION


Saturation temperature Tsat: The temperature at which a pure substance changes phase at a given pressure. Saturation pressure Psat: The pressure at which a pure substance changes phase at a given temperature. Vapor pressure (Pv): The pressure exerted by its vapor in phase equilibrium with its liquid at a given temperature. It is identical to the saturation pressure Psat of the liquid (Pv = Psat). Partial pressure: The pressure of a gas or vapor in a mixture with other gases. For example, atmospheric air is a mixture of dry air and water vapor, and atmospheric pressure is the sum of the partial pressure of dry air and the partial pressure of water vapor.

25 COMPRESSIBILITY AND SPEED OF SOUND


Coefficient of Compressibility
We know from experience that the volume (or density) of a fluid changes with a change in its temperature or pressure. Fluids usually expand as they are heated or depressurized and contract as they are cooled or pressurized. But the amount of volume change is different for different fluids, and we need to define properties that relate volume changes to the changes in pressure and temperature.

20

Two such properties are:


the bulk modulus of elasticity the coefficient of volume expansion .
Fluids, like solids, compress when the applied pressure is increased from P1 to P2.

21

Coefficient of compressibility (also called the bulk modulus of compressibility or bulk modulus of elasticity) for fluids

The coefficient of compressibility represents the change in pressure corresponding to a fractional change in volume or density of the fluid while the temperature remains constant. What is the coefficient of compressibility of a truly incompressible substance (v = constant)? A large value of indicates that a large change in pressure is needed to cause a small fractional change in volume, and thus a fluid with a large is essentially incompressible. This is typical for liquids, and explains why liquids are usually considered to be incompressible.

You might also like