5.

0 MEMORY
• Lecture Taken from Chap 6 :Computer
Organization and Architecture by Linda
Null
• Additional Resources taken from John
Wiley Zybook, Module 5

1
RECALL: The Bus System

2
 Overview of Computer
System Memory
• Objectives
• Master the concepts of hierarchical memory
organization.
• Understand how each level of memory contributes to
system performance, and how the performance is
measured.
• Master the concepts behind cache memory, virtual
memory, memory segmentation, paging and address
translation.

3
 5.1 Introduction

• Memory lies at the heart of the stored-program

computer.
• In this chapter, we focus on memory
organization.
• A clear understanding of these ideas is
essential for the analysis of system
performance.

4
 5.2 Types of Memory

• There are two kinds of main memory: random

access memory, RAM, and read-only-memory,
ROM.
• There are two types of RAM, dynamic RAM (DRAM)
and static RAM (SRAM).
• Dynamic RAM consists of capacitors that slowly leak
their charge over time. Thus they must be refreshed
every few milliseconds to prevent data loss.
• DRAM is “cheap” memory owing to its simple design.

5
 5.2 Types of Memory

• SRAM consists of circuits similar to the D flip-flop

that we studied in Chapter 3.
• SRAM is very fast memory and it doesn’t need to
be refreshed like DRAM does. It is used to build
cache memory, which we will discuss in detail later.
• ROM also does not need to be refreshed, either. In
fact, it needs very little charge to retain its memory.
• ROM is used to store permanent, or semi-
permanent data that persists even while the system
is turned off.
6
 5.3 The Memory Hierarchy

• Generally speaking, faster memory is more

expensive than slower memory.
• To provide the best performance at the lowest cost,
memory is organized in a hierarchical fashion.
• Small, fast storage elements are kept in the CPU,
larger, slower main memory is accessed through
the data bus.
• Larger, (almost) permanent storage in the form of
disk and tape drives is still further from the CPU.

7
 5.3 The Memory Hierarchy
• Faster memory is more expensive than slower memory.
• For the best performance at the lowest cost, memory is organized in a
hierarchical fashion.
• Small, fast storage elements are kept in the CPU, larger, slower main memory
is accessed through the data bus.
• Larger, (almost) permanent storage in the form of disk and tape drives is still
further from the CPU.

Processor

Control
Secondary Tertiary
Storage Storage
Third Main (Tape)
Second Level (Disk)
Memory
On-Chip
Registers

Level
Cache

Datapath Cache (DRAM)

Cache (SRAM)
(SRAM)

Memory hierarchy
 5.3 The Memory Hierarchy

• This storage organization can be thought of as a pyramid:

9
 5.3 The Memory Hierarchy

• To access a particular piece of data, the CPU first

sends a request to its nearest memory, usually cache.

• If the data is not in cache, then main memory is

queried. If the data is not in main memory, then the
request goes to disk.
• Once the data is located, then the data, and a number
of its nearby data elements are fetched into cache
memory.
• We are most interested in the memory hierarchy that
involve registers, Cache memory, main memory and
virtual memory( a non system memory that acts as an
10
extension to main memory.
 5.3 The Memory Hierarchy

• This leads us to some definitions.

– A hit is when data is found at a given memory level.
– A miss is when it is not found.
– The hit rate is the percentage of time data is found at a given
memory level.
– The miss rate is the percentage of time it is not.
– Miss rate = 1 - hit rate.
– The hit time is the time required to access data at a given
memory level.
– The miss penalty is the time required to process a miss,
including the time that it takes to replace a block of memory
plus the time it takes to deliver the data to the processor.

11
 5.3 The Memory Hierarchy

• An entire blocks of data is copied after a hit

because the principle of locality tells us that once a
byte is accessed, it is likely that a nearby data
element will be needed soon.
• The clustering of memory references into groups is
an example of locality of reference.
• There are three forms of locality:
– Temporal locality- Recently-accessed data elements tend
to be accessed again in the near future.
– Spatial locality - Accesses tend to clustered in the address
space (for e.g as in arrays or loops).
– Sequential locality - Instructions tend to be accessed 12
 5.4 Cache Memory

• A Cache memory is a small, temporary, but fast memory

that the processor uses for information it is likely to need
again in the very near future
• The purpose of cache memory is to speed up accesses
by storing/copying recently/frequently used data into the
cache closer to the CPU, instead of storing it in main
memory.
• Although cache is much smaller than main memory, its
access time is a fraction of that of main memory.
• Unlike main memory, which is accessed by address,
cache is typically accessed by content; hence, it is often
called content addressable memory.
• Because of this, a single large cache memory isn’t always 13
 5.4 Cache Memory

• The “content” that is addressed in content

addressable cache memory is a subset of the bits of
a main memory address called a field.
• The fields into which a memory address is divided
provide a many-to-one mapping between larger
main memory and the smaller cache memory.
• Many blocks of main memory map to a single block
of cache. A tag field in the cache block
distinguishes one cached memory block from
another.

14
 5.4 Direct Mapping

(a)To perform direct mapping the binary main

memory address is partitioned into tag, block and
offset.
•The offset field identifies an address within a specific
block. It must contain appropriate number of bits (The
no of bytes if the machine is byte addressable or word
if word addressable dictate the no of bits in the offset
field). This is also true of the Block field. The tag field
is whatever is left over. See example.

15
 5.4 Direct Mapping

• Suppose our memory consists of 214 words, cache

has 16 = 24 blocks, and each block holds 8 words.
• For our field sizes, we know we need 4 bits for the
block, 3 bits for the word, and the tag is what’s left
over: Block is 24 (4bits); word is 23 (8 word); tag is
14-7 = 7 bits
• In direct mapping, blocks of main memory map into
the cache as shown in next slide.

16
Direct Mapping

17
 5.4 Cache Memory

• The simplest cache mapping scheme is direct mapped

cache.
• Direct Mapping uses a Modular approach
• In a direct mapped cache consisting of N blocks of
cache, block X of main memory maps to cache block Y
= X mod N.
• Thus, if we have 10 blocks of cache, block 7 of cache
may hold blocks 7, 17, 27, 37, . . . of main memory.
• Once a block of memory is copied into its slot in
cache, a valid bit is set for the cache block to let the
system know that the block contains valid data.
18
What could happen if there were no valid bit?
 6.4 Cache Memory

• The diagram below is a schematic of what cache

looks like.

• Block 0 contains multiple words from main memory,

identified with the tag 00000000. Block 1 contains
words identified with the tag 11110101.
• The other two blocks are not valid.

19
 5.4 Cache Memory

• The size of each field into which a memory address

is divided depends on the size of the cache.
• Suppose our memory consists of 214 words, cache
has 16 = 24 blocks, and each block holds 8 words.
– Thus memory is divided into 214 / 2 3 = 211 blocks.
• For our field sizes, we know we need 4 bits for the
block, 3 bits for the word, and the tag is what’s left
over:

20
 5.4 Cache Memory

• As an example, suppose a program generates the

address 1AA. In 14-bit binary, this number is:
00000110101010.
• The first 7 bits of this address go in the tag field, the
next 4 bits go in the block field, and the final 3 bits
indicate the word within the block.

21
 5.4 Cache Memory

• If subsequently the program generates the address

1AB, it will find the data it is looking for in block
0101, word 011.

• However, if the program generates the address,

3AB, instead, the block loaded for address 1AA
would be evicted from the cache, and replaced by
the blocks associated with the 3AB reference.
22
 5.4 Cache Memory

• Suppose a program generates a series of memory

references such as: 1AB, 3AB, 1AB, 3AB, . . .
The cache will continually evict and replace
blocks.
• The theoretical advantage offered by the cache is
lost in this extreme case.
• This is the main disadvantage of direct mapped
cache.
• Other cache mapping schemes are designed to
prevent this kind of thrashing.
23
 54 Cache Memory
Q1: Where can a block be placed
in the cache?
• Example Block 12 placed in 8 block cache:
– Fully associative, direct mapped, 2-way set associative
– S.A. Mapping = Block Number Modulo Number Sets
Fully associative: Direct mapped: Set associative:

block 12 can go anywhere block 12 can go only into block 12 can go anywhere in

block 4 (12 mod 8) set 0 (12 mod 4)

Block Block Block

01234567 01234567 01234567
no. no. no.

Set Set Set Set

Block-frame address
0 1 2 3

Block
1111111111222222222233
no.
01234567890123456789012345678901
Chapter 6: Memory 24
 5.4 Cache Memory

• Other Cache mapping schemes

(b)Fully Associative mapping
(c)Set Associative mapping
(b)Instead of placing memory blocks in specific cache locations
based on memory address, we could allow a block to go
anywhere in cache. Searching is needed to find where it would
go into.
• In this way, cache would have to fill up before any blocks are
evicted.
• This is how fully associative cache works.
• A memory address is partitioned into only two fields: the tag
25
and the word.
 5.4 Cache Memory

• Suppose, as before, we have 14-bit memory addresses

and a cache with 16 blocks, each block of size 8. The
field format of a memory reference is:

• When the cache is searched, all tags are searched in

parallel to retrieve the data quickly.
• This requires special, costly hardware unlike direct
mapping. Also direct mapping does not require any
searching, and each memory block has a specific
location to which it is mapped in the cache 26
 5.4 Cache Memory

• You will recall that direct mapped cache evicts a

block whenever another memory reference
needs that block.
• With fully associative cache, we have no such
mapping, thus we must devise an algorithm to
determine which block to evict from the cache.
• The block that is evicted is the victim block.
• There are a number of ways to pick a victim, we
will discuss them shortly.

27
Memory Mapping

28
 5.4 Cache Memory

(c )Set associative cache combines the ideas of direct

mapped cache and fully associative cache.
•An N-way set associative cache mapping is like direct
mapped cache in that a memory reference maps to a
particular location in cache.
•Unlike direct mapped cache, a memory reference
maps to a set of several cache blocks, similar to the
way in which fully associative cache works.
•Instead of mapping anywhere in the entire cache, a
memory reference can map only to the subset of cache
slots.
29
 5.4 Cache Memory

• The number of cache blocks per set in set

associative cache varies according to overall system
design.
• For example, a 2-way set associative cache can be
conceptualized as shown in the schematic below.
• Each set contains two different memory blocks.

30
 5.4 Cache Memory

• In set associative cache mapping, a memory

reference is divided into three fields: tag, set, and
word, as shown below.
• As with direct-mapped cache, the word field chooses
the word within the cache block, and the tag field
uniquely identifies the memory address.
• The set field determines the set to which the memory
block maps.

31
 5.4 Cache Memory

• Suppose we have a main memory of 214 bytes.

• This memory is mapped to a 2-way set associative
cache having 16 blocks where each block contains 8
words.
• Since this is a 2-way cache, each set consists of 2
blocks, and there are 8 sets.
• Thus, we need 3 bits for the set, 3 bits for the word,
giving 8 leftover bits for the tag:

32
 5.4 Cache Memory

• First-in, first-out (FIFO) is a popular cache

replacement policy.
• In FIFO, the block that has been in the cache the
longest, regardless of when it was last used.
• A random replacement policy does what its name
implies: It picks a block at random and replaces it
with a new block.
• Random replacement can certainly evict a block that
will be needed often or needed soon, but it never
thrashes.

33
 5.4 Cache Memory

• With fully associative and set associative cache, a

replacement policy is invoked when it becomes
necessary to evict a block from cache.
• An optimal replacement policy would be able to look
into the future to see which blocks won’t be needed
for the longest period of time.
• Although it is impossible to implement an optimal
replacement algorithm, it is instructive to use it as a
benchmark for assessing the efficiency of any other
scheme we come up with.

34
 5.4 Cache Memory

• The replacement policy that we choose depends

upon the locality that we are trying to optimize--
usually, we are interested in temporal locality.
• A least recently used (LRU) algorithm keeps track of
the last time that a block was assessed and evicts
the block that has been unused for the longest
period of time.
• The disadvantage of this approach is its complexity:
LRU has to maintain an access history for each
block, which ultimately slows down the cache.

35
 5.4 Cache Memory

• The performance of hierarchical memory is

measured by its effective access time (EAT).
• EAT is a weighted average that takes into account
the hit ratio and relative access times of successive
levels of memory.
• The EAT for a two-level memory is given by:
EAT = H  AccessC + (1-H)  AccessMM.
where H is the cache hit rate and AccessC and AccessMM are
the access times for cache and main memory, respectively.

36
 5.4 Cache Memory

• For example, consider a system with a main memory

access time of 200ns supported by a cache having a
10ns access time and a hit rate of 99%.
• The EAT is:
0.99(10ns) + 0.01(200ns) = 9.9ns + 2ns =
11ns.
• This equation for determining the effective access
time can be extended to any number of memory
levels, as we will see in later sections.

37
 5.4 Cache Memory

• Cache replacement policies must also take into

account dirty blocks, those blocks that have been
updated while they were in the cache.
• Dirty blocks must be written back to memory. A
write policy determines how this will be done.
• There are two types of write policies,write through
and write back.
• Write through updates cache and main memory
simultaneously on every write.

38
 5.4 Cache Memory

• Write back (also called copyback) updates memory

only when the block is selected for replacement.
• The disadvantage of write through is that memory
must be updated with each cache write, which slows
down the access time on updates. This slowdown is
usually negligible, because the majority of accesses
tend to be reads, not writes.
• The advantage of write back is that memory traffic is
minimized, but its disadvantage is that memory does
not always agree with the value in cache, causing
problems in systems with many concurrent users.

39
 5.4 Cache Memory

• The cache we have been discussing is called a

unified or integrated cache where both instructions
and data are cached.
• Many modern systems employ separate caches for
data and instructions.
– This is called a Harvard cache.
• The separation of data from instructions provides
better locality, at the cost of greater complexity.
– Simply making the cache larger provides about the same
performance improvement without the complexity.

40
 5.4 Cache Memory

• Cache performance can also be improved by

adding a small associative cache to hold blocks
that have been evicted recently.
– This is called a victim cache.
• A trace cache is a variant of an instruction
cache that holds decoded instructions for
program branches, giving the illusion that
noncontiguous instructions are really
contiguous.

41
 5.4 Cache Memory

• Most of today’s small systems employ multilevel

cache hierarchies.
• The levels of cache form their own small memory
hierarchy.
• Level1 cache (8KB to 64KB) is situated on the
processor itself.
– Access time is typically about 4ns.
• Level 2 cache (64KB to 2MB) may be on the
motherboard, or on an expansion card.
– Access time is usually around 15 - 20ns.

42
 5.4 Cache Memory

• In systems that employ three levels of cache, the

Level 2 cache is placed on the same die as the CPU
(reducing access time to about 10ns)
• Accordingly, the Level 3 cache (2MB to 256MB)
refers to cache that is situated between the
processor and main memory.
• Once the number of cache levels is determined, the
next thing to consider is whether data (or
instructions) can exist in more than one cache level.

43
 5.4 Cache Memory

• If the cache system used an inclusive cache, the

same data may be present at multiple levels of
cache.
• Strictly inclusive caches guarantee that all data in a
smaller cache also exists at the next higher level.
• Exclusive caches permit only one copy of the data.
• The tradeoffs in choosing one over the other
involve weighing the variables of access time,
memory size, and circuit complexity.

44
 5.5 Virtual Memory

• Cache memory enhances performance by providing

faster memory access speed.
• Virtual memory enhances performance by providing
greater memory capacity, without the expense of
adding main memory.
• Instead, a portion of a disk drive serves as an
extension of main memory.
• If a system uses paging, virtual memory partitions
main memory into individually managed page frames,
that are written (or paged) to disk when they are not
immediately needed.
45
 5.5 Virtual Memory

• A physical address is the actual memory address of

physical memory.
• Programs create virtual addresses that are mapped
to physical addresses by the memory manager.
• Page faults occur when a logical address requires
that a page be brought in from disk.
• Memory fragmentation occurs when the paging
process results in the creation of small, unusable
clusters of memory addresses.

46
 5.5 Virtual Memory

• Main memory and virtual memory are divided into

equal sized pages.
• The entire address space required by a process
need not be in memory at once. Some parts can be
on disk, while others are in main memory.
• Further, the pages allocated to a process do not
need to be stored contiguously-- either on disk or in
memory.
• In this way, only the needed pages are in memory
at any time, the unnecessary pages are in slower
disk storage.
47
 5.5 Virtual Memory

• Information concerning the location of each page,

whether on disk or in memory, is maintained in a data
structure called a page table (shown below).
• There is one page table for each active process.

48
 5.5 Virtual Memory

• When a process generates a virtual address, the

operating system translates it into a physical memory
address.
• To accomplish this, the virtual address is divided into
two fields: A page field, and an offset field.
• The page field determines the page location of the
address, and the offset indicates the location of the
address within the page.
• The logical page number is translated into a physical
page frame through a lookup in the page table.

49
 5.5 Virtual Memory

• If the valid bit is zero in the page table entry for the
logical address, this means that the page is not in
memory and must be fetched from disk.
– This is a page fault.
– If necessary, a page is evicted from memory and is replaced
by the page retrieved from disk, and the valid bit is set to 1.
• If the valid bit is 1, the virtual page number is replaced
by the physical frame number.
• The data is then accessed by adding the offset to the
physical frame number.

50
 5.5 Virtual Memory

• As an example, suppose a system has a virtual address

space of 8K and a physical address space of 4K, and the
system uses byte addressing.
– We have 213/210 = 23 virtual pages.
• A virtual address has 13 bits (8K = 2 13) with 3 bits for the page
field and 10 for the offset, because the page size is 1024.
• A physical memory address requires 12 bits, the first two bits
for the page frame and the trailing 10 bits the offset.

51
 5.5 Virtual Memory

• Suppose we have the page table shown below.

• What happens when CPU generates address 5459 10
= 10101010100112?

52
 6.5 Virtual Memory

• The address 10101010100112 is converted to

physical address 010101010011 because the page
field 101 is replaced by frame number 01 through a
lookup in the page table.

53
 5.5 Virtual Memory

• What happens when the CPU generates address

10000000001002?

54
 5.5 Virtual Memory

• We said earlier that effective access time (EAT) takes

all levels of memory into consideration.
• Thus, virtual memory is also a factor in the
calculation, and we also have to consider page table
access time.
• Suppose a main memory access takes 200ns, the
page fault rate is 1%, and it takes 10ms to load a
page from disk. We have:
EAT = 0.99(200ns + 200ns) 0.01(10ms) = 100, 396ns.

55
 5.5 Virtual Memory

• Even if we had no page faults, the EAT would be

400ns because memory is always read twice: First to
access the page table, and second to load the page
from memory.
• Because page tables are read constantly, it makes
sense to keep them in a special cache called a
translation look-aside buffer (TLB).
• TLBs are a special associative cache that stores the
mapping of virtual pages to physical pages.

The next slide shows how all the pieces fit together.
56
5.5 Virtual Memory

57
 5.5 Virtual Memory

• Another approach to virtual memory is the use of

segmentation.
• Instead of dividing memory into equal-sized pages,
virtual address space is divided into variable-length
segments, often under the control of the programmer.
• A segment is located through its entry in a segment
table, which contains the segment’s memory location
and a bounds limit that indicates its size.
• After a page fault, the operating system searches for
a location in memory large enough to hold the
segment that is retrieved from disk.
58
 5.5 Virtual Memory

• Both paging and segmentation can cause

fragmentation.
• Paging is subject to internal fragmentation because a
process may not need the entire range of addresses
contained within the page. Thus, there may be many
pages containing unused fragments of memory.
• Segmentation is subject to external fragmentation,
which occurs when contiguous chunks of memory
become broken up as segments are allocated and
deallocated over time.

59
 5.5 Virtual Memory

• Large page tables are cumbersome and slow, but with

its uniform memory mapping, page operations are
fast. Segmentation allows fast access to the segment
table, but segment loading is labor-intensive.
• Paging and segmentation can be combined to take
advantage of the best features of both by assigning
fixed-size pages within variable-sized segments.
• Each segment has a page table. This means that a
memory address will have three fields, one for the
segment, another for the page, and a third for the
offset.
60
 5.6 A Real-World Example

• The Pentium architecture supports both paging and

segmentation, and they can be used in various
combinations including unpaged unsegmented,
segmented unpaged, and unsegmented paged.
• The processor supports two levels of cache (L1 and
L2), both having a block size of 32 bytes.
• The L1 cache is next to the processor, and the L2
cache sits between the processor and memory.
• The L1 cache is in two parts: and instruction cache (I-
cache) and a data cache (D-cache).
The next slide shows this organization schematically.
61
5.6 A Real-World Example

62
 Conclusion

• Computer memory is organized in a hierarchy, with

the smallest, fastest memory at the top and the
largest, slowest memory at the bottom.
• Cache memory gives faster access to main memory,
while virtual memory uses disk storage to give the
illusion of having a large main memory.
• Cache maps blocks of main memory to blocks of
cache memory. Virtual memory maps page frames
to virtual pages.
• There are three general types of cache: Direct
mapped, fully associative and set associative.
63
 Conclusion

• With fully associative and set associative cache,

as well as with virtual memory, replacement
policies must be established.
• Replacement policies include LRU, FIFO, or LFU.
These policies must also take into account what
to do with dirty blocks.
• All virtual memory must deal with fragmentation,
internal for paged memory, external for
segmented memory.

64
End of Chapter 6

65