Networking

Components and
Devices

1
 To complete our examination of networking on a
physical level, this chapter looks at the network
devices used to create networks.
 Hubs
 Switches
 Bridges
 Repeaters
 Routers
 Gateways
 CSU/DSU
 Wireless access points (WAPs)
 Modems
 Network interface cards (NICs)
 Transceivers
 Firewalls 2
Hubs
 Hubs are simple network devices, and their
simplicity is reflected in their low cost.
 Small hubs with four or five ports (often referred to
as workgroup hubs) provide everything needed to
create a small network.
 Most hubs are referred to as either active or
passive.
 Active regenerate a signal before forwarding it to all
the ports on the device and requires a power supply.
 Passive hubs, which today are seen only on older
networks, do not need power and they don't
regenerate the data signal.
3
4
 The basic function of a hub is to take data
from one of the connected devices and
forward it to all the other ports on the hub.
 The method of sending data to all systems
regardless of the intended recipient is
referred to as broadcasting.
 This method of operation is inefficient
because, in most cases, the data is intended
for only one of the connected devices.
 Due to the inefficiencies of the hub system
and the constantly increasing demand for
more bandwidth, hubs are slowly but surely
being replaced with switches. 5
6
Switches
 On the surface, a switch looks much like a
hub. Despite their similar appearance,
switches are far more efficient than hubs and
are far more desirable for today's network
environments.
 As with a hub, computers connect to a switch

via a length of twisted-pair cable. Multiple

switches are often interconnected to create
larger networks.
7
 Rather than forwarding data to all the connected
ports, a switch forwards data only to the port on
which the destination system is connected.
 It looks at the Media Access Control (MAC)
addresses of the devices connected to it to
determine the correct port. A MAC address is a
unique number that is stamped into every NIC. By
forwarding data only to the system to which the data
is addressed, the switch decreases the amount of
traffic on each network link dramatically. 8
9
 Collisions occur on the network when two devices attempt
to transmit at the same time. Such collisions cause the
performance of the network to degrade. By channeling
data only to the connections that should receive it,
switches reduce the number of collisions that occur on
the network.
 Switches can also further improve performance over the
performance of hubs by using a mechanism called full-
duplex. On a standard network connection, the
communication between the system and the hub is said
to be half-duplex.
 In a half-duplex connection, data can be either sent or
received on the wire but not at the same time. Because
switches manage the data flow on the connection, a
switch can operate in full-duplex mode. It can send and
receive data on the connection at the same time. In a full-
duplex connection, the maximum data throughput is
double that for a half-duplex connectionfor example,
10Mbps becomes 20Mbps, and 100Mbps becomes
200Mbps. 10
Switching Methods
 Cut-through
 the switch begins to forward the packet as soon as it is received.
 No error checking is performed on the packet,
 so the packet is moved through quickly.
 the switch can propagate errors
 30 times faster than store-and-forward switching
 Store-and-forward
 the switch waits to receive the entire packet before beginning to
forward it.
 also performs basic error checking.
 Fragment-free
 works by reading only the part of the packet that enables it to
identify fragments of a transmission.
 On some managed switches, you can select the switching method
you want to use. 11
Working with Hubs and
Switches
 Hubs and switches have two types of ports: medium
dependent interface (MDI) or uplink port and
medium dependent interface crossed (MDI-X).
 Uplink port allows you to connect two hubs and
switches to create larger networks.

12
Cable Crimping
 Two types of cables are used to connect devices to
hubs and switches: crossover cables and straight-
through cables.
 The difference between the two types is that in a
crossover cable, two of the wires are crossed; in a
straight-through cable, all the wires run straight
through.
 Crossover – PC to PC, Hub to Hub, Switch to Hub,
connects the same devices
 Straight-through – PC to Hub, PC to Switch,
connects different devices 13
14
15
Hub and Switch Indicator
Lights
 Both hubs and switches use light-emitting
diodes (LEDs) to indicate certain connection
conditions.
 At the very least, a link light on the hub will
indicate the existence of a live connection.
 On higher-end devices, additional lights might
indicate
 activity,
 the speed of the connection,
 whether the connection is at half- or full-duplex,
 sometimes errors or collisions. 16
Managed Hubs and Switches
A managed device has an interface through
which it can be configured to perform certain
special functions.
 For example, it may allow for port mirroring,
which can be useful for network monitoring,
or allow ports to be specified to operate at a
certain speed.
 managed devices are considerably more
expensive than unmanaged devices.
 Eg. Cisco Switches
17
Bridges
 Bridges are networking devices that connect
networks.
 Sometimes it is necessary to divide networks

into subnets to reduce the amount of traffic

on each larger subnet or for security reasons.
 Once divided, the bridge connects the two

subnets and manages the traffic flow

between them. Today, network switches have
largely replaced bridges.
18
19
 A bridge functions by blocking or forwarding data,
based on the destination MAC address written into
each frame of data.
 If the bridge believes the destination address is on a
network other than that from which the data was
received, it can forward the data to the other
networks to which it is connected.
 If the address is not on the other side of the bridge,
the data is blocked from passing. Bridges "learn" the
MAC addresses of devices on connected networks
by "listening" to network traffic and recording the
network from which the traffic originates.
 The advantages of bridges are simple and
significant. By preventing unnecessary traffic from
crossing onto other network segments, a bridge can
dramatically reduce the amount of network traffic on
a segment.
20
Repeater
 Repeaters are usually used to strengthen signals
going long distances.
 A repeater amplifies the signal it receives on one
port before it transmits it on other ports.
 Because the repeater does not check on the
contents of the data it receives or retransmits,
frames that are corrupted by noise and other
factors can also be repeated.
 The development of the hub replaced the
repeater for all practical purposes, because it
performs the same functions, and can include
additional features.
21
Routers
 Routers are network devices that literally route data
around the network.
 By examining data as it arrives, the router can
determine the destination address for the data; then,
by using tables of defined routes, the router
determines the best way for the data to continue its
journey.
 Unlike bridges and switches, which use the
hardware-configured MAC address to determine the
destination of the data, routers use the software-
configured network address to make decisions.
 This approach makes routers more functional than
bridges or switches, and it also makes them more
complex because they have to work harder to
determine the information. 22
23
 A router is used to provide connectivity across
wide area network (WAN) links and route
information between two LAN segments.
 The figure below shows a router with two LAN
ports (marked AUI 0 and AUI 1) and two WAN
ports (marked Serial 0 and Serial 1). This router is
capable of routing data between two LAN
segments and two WAN segments.

24
Dedicated Hardware Versus
Server-Based Routers
 A router can be either a dedicated hardware device
or a server system that has at least two network
interfaces installed in it.
 advantages of dedicated hardware routers:
 Typically faster than server-based routers
 Generally more reliable than server-based routers
 Easier to harden against attacks than server-based routing
solutions
 disadvantages of dedicated hardware routers:
 More expensive than server-based router solutions; extra
functionality may have to be purchased
 Often require specialized skills and knowledge to manage
them
 Limited to a small range of possible uses 25
When Do You Need to Use a
Router?
 Not every network needs a router.
 a simple switch-based LAN can provide all the file and
print sharing your business needs within the LAN.
 Situations in which a router might be needed:
 to resolve network congestion, you can divide your
network into multiple subnets and connect them using
a router.
 You want to connect to branch offices or other wide
area networks, such as the Internet.
 You want to be able to filter the network traffic that
passes between one LAN and the next, or between
your network and the Internet.
26
 Gateways
 The term gateway is applied to any device, system, or software
application that can perform the function of translating data from
one format to another.
 Actually, the term gateway refers more to a network role than a
network device.
 For example, a router that can route data from an IPX network to
an IP network is, technically, a gateway.
 Another example of a gateway involves the Systems Network
Architecture (SNA) gateway, which converts the data format used
on a PC to that used on an IBM mainframe or minicomputer. A
system that acts as an SNA gateway sits between the client PC
and the mainframe and translates requests and replies from both
directions.
 The definition of gateways is vague, it's because there is no
definite answer. The function of a gateway is very specific, but
how the gateway functionality is implemented is not.
27
28
CSUs/DSUs
 A Channel Service Unit/Data Service Unit
(CSU/DSU) acts as a translator between the LAN
data format and the WAN data format.
 Such a conversion is necessary because the
technologies used on WAN links are different from
those used on LANs.
 A CSU/DSU has physical connections for the LAN
equipment, and another connection for a WAN.
Traditionally, the CSU/DSU has been in a separate
box from other networking equipment; however, the
increasing use of WAN links means that some
router manufacturers are now including the
CSU/DSU functionality in routers or are providing
the expansion capability to do so. 29
30
Modems
 Modem is a contraction of the terms modulator and
demodulator.
 Modems perform a simple function: They translate
digital signals from a computer into analog signals
that can travel across conventional phone lines.
 Modems provide a relatively slow method of
communication. In fact, the fastest modem available
on the market today has a maximum speed of
56Kbps.
 available as
 internal devices that plug into PCI/ISA slots
 external devices that plug into serial or USB ports;
 PCMCIA cards designed for use in laptops
31
32
Network Interface Cards (NICs)
 NICs are the mechanisms by which computers
connect to a network.
 NICs come in all shapes and sizes, and they come
in prices to suit all budgets.
 Known as network card, network adapter, and LAN
adapter, etc.
 When buying one consider
 Network compatibility – Ethernet/Token Ring
 Bus compatibility – PCI/ ISA /PCI-e
 Port compatibility – UTP/ Fibre
 Hardware compatibility – Easy to install / Recognized by
many OS’s
33
34
A network interface typically has at
least two LEDs that indicate certain
conditions:
 Link light - indicates whether a
network connection exists between
the card and the switch/hub.
 Activity light - indicates network

activity.
 Speed light - indicates that the

interface is connected at a certain

speed.
35
Wireless Access Point (WAP)
 are a transmitter and receiver (transceiver)
device used for wireless LAN (WLAN) radio
signals.
 Depending on the size of the network, one or
more WAPs may be required. Additional
WAPs are used to allow access to more
wireless clients and to expand the range of
the wireless network.
 Communication depends on
 Distance between the client and the WAP
 Environmental conditions 36
37
Transceivers
 The term transceiver does not necessarily describe
a separate network device but rather an integrated
technology embedded in devices.
 transceiver = transmitter and a receiver
 device that receives data, converts it, and then
sends it to another location
 RF transceivers, fiber-optic transceivers, Ethernet
transceivers, are examples
 can also be used in pairs to insert a fiber segment
into copper networks
38
Fiber Optic Transceiver
39
Firewall
 a hardware or software system that is used to
separate one computer or network from another
one.
 The most common type is used to protect a
computer or an entire network from unauthorized
access from the Internet.
 can also be used to control the flow of data to and
from multiple networks within the same organization.
Firewalls
 can be programmed to filter data packets based on
the information that is contained in the packets. 40