Router and IOS Basics

Cisco routers and CLI

Lecture 4 – Router and IOS Basics

 To properly understand the lecture and to prepare for the quiz

on Router and IOS Basics in your next class, you should have
completed the following before coming to class:

1. Watched the video and pre-read the remaining lecture for

the class.
2. Read the relevant Chapters.
3. Read the summary at the end of the chapter.
4. Reviewed all of the Exam Essentials.
5. Answered all the chapter review questions.

COMP10023 2
 Perform POST and Load Bootstrap
Program

 When a Cisco router powers up, it performs a power-on self test

(POST).
 During this self test, the router executes diagnostics from ROM on
all hardware modules.
 After the POST, the following events occur as the router initializes:
COMP10023 3
Locate and Load the Cisco IOS
Software

 The bootstrap program locates the Cisco IOS software and loads it into
RAM. Cisco IOS files can be located in one of three places: flash memory, a
TFTP server, or another location indicated in the startup configuration file.
 By default, the Cisco IOS software loads from flash memory. The
configuration settings must be changed to load from one of the other
locations.
COMP10023 4
Locate and Execute the Startup
Configuration

 After the Cisco IOS software is loaded, the bootstrap program searches for
the startup configuration file in NVRAM. This file contains the previously
saved configuration commands and parameters, including interface
addresses, routing information, passwords, and other configuration
parameters.

COMP10023 5
Initial startup of Cisco routers
 Note: If the startup configuration file does not exist in NVRAM, the
router may search for a TFTP server.
 If the router detects that it has an active link to another configured
router, it sends a broadcast searching for a configuration file across
the active link. This condition will cause the router to pause, but you
will eventually see a console message like the following one:

<router pauses here while it broadcasts for a configuration file across an active link>

%Error opening tftp://255.255.255.255/network-confg (Timed out)

%Error opening tftp://255.255.255.255/cisconet.cfg (Timed out)

COMP10023 6
Initial startup of Cisco routers
 When booting a router that does not contain a startup configuration
file, you will see the following question after the IOS has been
loaded:
Would you like to enter the initial configuration dialog? [yes/no]:
 Setup mode will not be used in this course to configure the router.
When prompted to enter setup mode, always answer no. If you
answer yes and enter setup mode, you can press Ctrl-C at any time
to terminate the setup process.
 You can also enter the setup mode by typing in the command setup
 When setup mode is not used, the IOS creates a default running-
config. The default running-config is a basic configuration file that
includes the router interfaces, management interfaces, and certain
default information. The default running-config does not contain any
interface addresses, routing information, passwords, or other
specific configuration information..
COMP10023 7
Config Files

 The startup configuration file is the saved configuration file that sets the
properties of the device each time the device is powered up. This file is
stored in non-volatile RAM (NVRAM), meaning that it is saved even
when power to the device is turned off.
 When a Cisco router is first powered up, it loads the Cisco IOS software
to working memory, or RAM. Next, the startup configuration file is
copied from NVRAM to RAM. When the startup configuration file is
loaded into RAM, the file becomes the initial running configuration. This
file is NOT saved when power to the device is turned off.
COMP10023 8
Location of the Cisco IOS
IOS stored in Flash
 Non-volatile storage – not lost when power is lost
 Can be changed or overwritten as needed
 Can be used to store multiple versions of IOS
 IOS copied from flash to volatile RAM
 Quantity of flash and RAM memory determines IOS that can be
used

COMP10023 9
Router user interface

 The Cisco IOS software uses a command-line interface

(CLI) as the traditional console environment.

This environment is accessible through several methods:
 Console – out-of-band
 AUX port (modem) – out-of-band
 Telnet/SSH

COMP10023 10
 Out-of-band Management
 Out-of-band management
requires a computer to be directly
connected to the console port or
auxiliary port (AUX) of the
network device being configured.
 Does not require the local
network connections on the
device to be active.
 Used to initially configure a
network device.
 Also useful when the network
connectivity is not functioning
correctly and the device cannot
be reached over the network.
 Requires a terminal emulation
client installed on the PC.
COMP10023 11
In-band Management
 Used to monitor and make
configuration changes to a
network device over a network
connection.
 For a computer to connect to the
device and perform in-band
management tasks, at least one
network interface on the device
must be connected to the network
and be operational.
 Either Telnet, HTTP (using
SDM/CPP) or SSH can be used
to access a Cisco device.
 A web browser or a Telnet/SSH
client program can be used to
monitor the network device or
make configuration changes.
COMP10023 12
 Navigating the IOS

User EXEC Mode

The User EXEC mode allows only a
limited number of basic monitoring
Limited examination of router.
Remote access. commands and is often referred to
as view-only mode.
Switch>
Router>

Privileged EXEC Mode

The Privileged EXEC mode, by
default, allows all monitoring Detailed examination of router. Debugging and
commands, as well as execution testing. File manipulation. Remote access.
of configuration and
Switch#
management commands. Router#

COMP10023 13
Navigating the IOS

Privileged EXEC Mode

Detailed examination of router. Debugging and Router>ping 192.168.1.1
testing. File manipulation. Remote access.
Router# show running-config
Switch#
Router# Router(config)# Interface FastEthernet 0/0

Router(config-if)# ip address 192.168.1.2 255.255.255.0

Global Configuration Mode

Global configuration commands
Switch(config)# Switch>ping 192.168.1.1
Router(config)# Switch# show running-config

Switch(config)# Interface FastEthernet 0/1

Switch(config-if)# Description connection to NESA Lan

Other Configuration Modes
Special service or interface configurations.
Switch(config-mode)#
Router(config-mode)#
More later
COMP10023 14
Cisco Hardware and Software
Components

COMP10023 15
Operation of Cisco IOS Software
Operating Environment Prompt Usage

ROM monitor > or ROMMON> Failure or password recovery

Boot ROM Router(boot) Flash image upgrade

Cisco IOS Router> Normal operation

The Cisco IOS devices have three distinct operating environments or modes:
• ROM monitor
• Boot ROM
• Cisco IOS
The show flash command is used to verify that the system has sufficient memory
to load a new Cisco IOS image.

COMP10023 16
Establishing a Terminal Session
Router

Console port
Terminal or a
PC with
Rollover cable
terminal
emulation
software

Com1 or Com2 serial port

Take the following steps to connect a terminal to the console port on
the router:
 Connect the terminal using the RJ-45 to RJ-45 rollover cable and an

RJ-45 to DB-9 or RJ-45 to DB-25 adapter.

 Configure the terminal or PC terminal emulation software for 9600

baud, 8 data bits, no parity, 1 stop bit, and no flow control.

COMP10023 17
Establishing a Terminal Session
with Terraterm Pro

 Important: A console
connection is not the
same as a network
connection!

COMP10023 18
Logging into the router – more
later User Access Verification
Password:
Router> User-Mode Prompt
Navigating
Router> enable
between Password:
modes Router# Privileged-Mode Prompt
Router# disable
Router>
Router> exit

 Two commands can be used to set a password used to access

privileged EXEC mode: enable password and enable secret
 The following are some of the specific modes that can also be
accessed from the global configuration mode: (more later)
 Interface

 Line

 Router

COMP10023 19
Keyboard help in the router CLI

COMP10023 20
Keyboard help in the router CLI
Router#
Router#cl?
clear clock
Router#clock
% Incomplete command.
Router#clock ?
set Set the time and date
Router#clock set This example is showing how to
% Incomplete command.
Router#clock set ? use the ? (help) with the IOS CLI.
hh:mm:ss Current Time
Router#clock set 08:47 ?
hh:mm:ss This would work the same with any
Router#clock set 08:47:00 command that you are using.
% Incomplete command.
Router#clock set 08:47:00 ?
<1-31> Day of the month
MONTH Month of the year
Router#clock set 08:47:00 30 03
^
% Invalid input detected at '^' marker.
Router#clock set 08:47:00 30 March
% Incomplete command.
Router#clock set 08:47:00 30 March ?
<1993-2035> Year
Router#clock set 08:47:00 30 March 2015
Router#

COMP10023 21
Enhanced editing commands
Command Description

Ctrl-A Moves to the beginning of the command line

Esc-B Moves back one word

Ctrl-B (or right arrow) Moves back one character

Ctrl-E Moves to the end of the command line

Ctrl-F (or left arrow) Moves forward one character

Esc-F Moves forward one word

$ indicates that there is more text to the left of the $

 Ctrl-Z is a command used to back out of configuration mode. This

will return the user to the privileged EXEC mode prompt.

COMP10023 22
Router command history

Command Description

Ctrl-P (or up arrow key) Recalls last (previous) command

Ctrl-N (or down arrow key) Recalls most recent command

Router> show history Shows command buffer

Router> terminal history size number-of-lines Sets the command history buffer size*

Router> terminal no editing Disables advanced editing features

Router> terminal editing Re-enables advanced editing

<Tab> Completes the entry

terminal history size: maximum number of commands is 256

COMP10023 23
Troubleshooting command line
errors

COMP10023 24
Filter Command Output
 Filtering commands can be used to display specific sections of
output. To enable the filtering command, enter a pipe (|) character
after the show command and then enter a filtering parameter and a
filtering expression.

 The filtering parameters that can be configured after the pipe

include:
o section - This displays the entire section that starts with the filtering expression.
o include - This includes all output lines that match the filtering expression.
o exclude - This excludes all output lines that match the filtering expression.
o begin - This displays all the output lines from a certain point, starting with the
line that matches the filtering expression.

 Note: Output filters can be used in combination with

any show command.

COMP10023 25
Resource material for PowerPoints
from:

Rick Graziani

Todd Lammle

COMP10023 26