Chapter Two

Kinematics of
particles
Introduction
Kinematics: is the branch of dynamics which
describes the motion of bodies without reference
to the forces that either causes the motion or
are generated as a result of the motion.
 Kinematics is often referred to as the “geometry
of motion”
Examples of kinematics problems that engage
the attention of engineers.
 The design of cams, gears, linkages, and
other machine elements to control or
produce certain desired motions, and
 The calculation of flight trajectory for aircraft,
rockets and spacecraft.
• If the particle is confined to a specified path, as with a bead
sliding along a fixed wire, its motion is said to be
Constrained.
Example 1. - A small rock tied to the end of a string and whirled
in a circle undergoes constrained motion until the string
breaks.
• If there are no physical guides, the motion is
said to be unconstrained.

Example 2 - Airplane, rocket

• The position of a particle P at any time t can be
described by specifying its:
- Rectangular coordinates; X,Y,Z
- Cylindrical coordinates; r,θ,z
- Spherical coordinates; R,θ,Ф
- Also described by measurements along the
tangent t and normal n to the curve(path
• The motion of particles(or rigid bodies)
may be described by using coordinates
measured from fixed reference axis
(absolute motion analysis) or by using
coordinates measured from moving
reference axis (relative motion analysis).
Rectilinear motion
• Is a motion in which a particle moves along a
straight line(one-dimensional motion).
• Consider a particle P moving along a straight
line.
Average velocity: for the time interval Δt, it is defined as the ratio of
the displacement Δs to the time interval Δt.
s
Vav =
t
……………………………………………………2.1
• As Δt becomes smaller and approaches zero in the limit, the
average velocity approaches the instantaneous velocity of the
particle. s ds 
V  lim Vav  lim  S
t  0 t  0 t dt …………………………2.2
Average acceleration
For the time interval Δt, it is defined as the ratio of the change
in velocity Δv to the time interval Δt.
……………………………………… 2.3
Instantaneous acceleration
……………………………………………
2.4(a) v dv 
a  lim  v
t  0 t dt

v dv d  ds  d 2 s……………………………… 2.4(b)
a  lim      2 s
t  0 t dt dt  dt  dt
• Note:-The acceleration is positive or negative
depending on whether the velocity
increasing or decreasing.
• Considering equation 2.2 and 2.4(a) , we
have ds dv
dt  
v a
 vdv ads

ds d s   
dt  
 
 s d s  s ds
s s
 General representation of
Relationship among s, v, a & t.
1. Graph of s vs. t

• By constructing tangent to the curve at any time t,

we obtain the slope, which is the velocity v = ds/dt
2. Graph of v vs. t

• The slope dv/dt of the v-t curve at any instant gives the
acceleration at that instant.
• The area under the v-t curve during time dt is vdt which
is the displacement ds.
• The area under the v-t curve is the net
displacement of the particle during the
interval from t1 to t2.
s2 t2

ds vdt
s1 t1

s2  s2  (area under v-t curve )

3. Graph of a vs. t

• The area under the a-t curve during time dt is the net change in
velocity of the particle between t1 and t2.
v2 t2

dv
v1
 adt
t1

v2 - v1 = (area under a-t curve)

4. Graph of a vs. s

• The net area under the curve b/n position

coordinates s1 and s2 is
v2 s2

vdv  ads
v1 s1

1 2 2
(v2  v1 )  (areas under a-s curve)
2
5. Graph of v vs. s

dv
tan   ds  CB
1 v
dv CB
  vdv CBds
ds v
• The graphical representations described are useful for:-
 visualizing the relationships among the several motion quantities.

 approximating results by graphical integration or differentiation

when a lack of knowledge of the mathematical relationship

prevents its expression as an explicit mathematical function .

 experimental data and motions that involve discontinuous

relationship b/n variables.

Methods for determining the
velocity and displacement
functions
a) Constant acceleration, (a=const.)
- boundary conditions
at t=0 , s=s0 and v=v0
using integrating
dv
a  adt dv
dt
v t

dv  adt 
vo 0
v  v o at

 v v o  at
• Using v s
vdv ads  vdv  ads
vo so
2
v2 v 2  vo
a s  so 
v s
 as so 
2 vo
2
2
 v 2 vo  2a(s  s0 )
ds
v   ds vdt
dt
• Using
s t
 ds
s0
(vo  at ) dt
o

at 2
 s  so vo t 
2
1
 s so  vo t  at 2
2
• These relations are necessarily
restricted to the special case where the
acceleration is constant.
• The integration limits depend on the
initial and final conditions and for a
given problem may be different from
those used here.
• Typically, conditions of motion are specified by
the type of acceleration experienced by the
particle. Determination of velocity and position
requires two successive integrations.

• Three classes of motion may be defined for:

- acceleration given as a function of time, a = f(t)
- acceleration given as a function of position, a = f(x)
- acceleration given as a function of velocity, a = f(v)
b) Acceleration given as a function of time, a=f(t)
v t  t t
dv
a  f t  dv  f t dt dv f t dt vt  v0 f t dt
dt v0 0 0
x t  t t
dx
vt  dx vt dt dx vt dt xt  x0 vt dt
dt x0 0 0

c) Acceleration given as a function of position, a = f(x)

dx dx dv dv
v or dt  a or a v  f x 
dt v dt dx
v x x
v dv  f x dx v dv  f x dx 1
2 v 2  12 v02  f x dx
v0 x0 x0
d) Acceleration given as a function of velocity, a =
f(v)
v t
dv dv dv
a  f v  dt  dt
dt f v  v0
f v  0
v
dv

v0
f v 
t

x v
dv v dv v dv
v a  f v  dx   dx  
dx f v  x0 v0
f v 
v
v dv
x  x0  
v0
f v 
Example 1
• Consider a particle moving in a straight line, and
assuming that its position is defined by the equation
s 6t 2  t 3
• Where, t is express in seconds and s is in meters.
Determine the velocity and acceleration of the
particles at any time t
Example 2
• A particle moves along the x axis with an initial velocity
Vx= 50ft/sec at orgine when t= 0 for first 4 sec it has no
acceleration, there after it is acted on by a retarding
force which gives it constant acceleration a =-10 ft/sec2.
x

calculate the velocity and the x-coordinate of particle for

the condition of t=8sec and t=12sec and find the max
positive x coordinate reached by the particle.
Example 3
• A boll is thrown vertically up with a velocity of
80 ft/sec at the edge of 200 ft cliff calculate
the height h to which the boll rises and the
total time t after release for the boll to reach
the bottom of the cliff. Neglect air resistance
and take the downward acceleration to be
32.2ft/sec2
Example 4
• A girl rolls a boll up an inclined and allows it to return
to her. For the angle  and boll involved, the
acceleration of the boll along the inclined is constant
at 0.25g, directed down the inclined. If the boll is
released with a speed of 4m/s, determine the
distance S it moves up the incline before reversing its
direction and total time t required for the boll to
return to the child hand.
Plane curvilinear motion
Curvilinear motion of a particle
• When a particle moves along a curve other
than a straight line, we say that the
particle is in curvilinear motion.
Plane curvilinear motion
• The analysis of motion of a particle along a
curved path that lies on a single plane.
Rectangular co-ordinates (x-y-
z)
• This is particularly useful for describing
motions where the x,y and z-components
of acceleration are independently
generated.
• When the position of a particle P is defined
at any instant by its rectangular
coordinate x,y and z, it is convenient to
resolve the velocity v and the
acceleration a of the particle into
rectangular components.
Assumptions
• Neglect the aerodynamic drag, the
earth curvature and rotation,
• The altitude range is so small enough
so that the acceleration due to gravity
can be considered constant, therefore;
• Rectangular coordinates are useful for the
trajectory analysis.
• In the case of the motion of a projectile, it
can be shown that the components of the
acceleration are
  
a x  x 0 a y  y  g a z  z 0
Boundary conditions
at t=0 ; x=x ,y=y ; vx=vxo and vy=vy0
0 0

Position
x  x0  v x 0 t
1
y  y0 v y 0 t  gt 2 • In all these expressions,
2
z  zo  v z ot the subscript zero
Velocity denotes initial
 conditions
v x  x v x 0

v y  y v y 0  gt

v z  z v zo
2 2
, vy v yo  2 g ( y  yo )
• But for two dimensional motion of the projectile,

x  x0  v x 0 t
1
y  y0 v y 0 t  gt 2
2

v x  x v x 0

v y  y v y 0  gt
2 2
vy v yo  2 g ( y  yo )
• If the projectile is fired from the origin O, we have
xo=yo=0 and the equation of motion reduced to
x v x 0 t v x v x 0
1 v y v y 0  gt
y v y 0 t  gt 2
2
Example
vx 50  16t
The curvilineat motion of a particle is defined by
y 100  4t 2
and , where Vx is meter per
second. Y is in meter and t is sec, it is also
known that x=0 when t=0. plot the path of the
particle and determine its velocity and
acceleration when the position y=0 is reached.
Example
A projectile is launched from point A with the
initial condition shown in the fig determine
the slant distance S which locates the point B
of impact. Calculate the time of flight t.
Example
A projectile is launched with initial speed 200
m/s at an angle of 60 with respect to the
horizontal, compute the range R as measured
up inclined.

R
200
60 20
 Curvilinear motion
Normal and tangential coordinates
Normal and tangential coordinate
• When a particle moves along a curved
path, it is sometimes convenient to
describe its motion using coordinates
other than Cartesian.
• When the path of motion is known, normal
(n) and tangential (t) coordinates are often
used.
• They are path variables, which are
measurements made along the tangent t
and normal n to the path of the particle.
• The coordinates are considered to move
along the path with the particle.
• In the n-t coordinate system, the origin is
located on the particle (the origin moves
with the particle).
• The t-axis is tangent to the path (curve) at
the instant considered, positive in the
direction of the particle’s motion.

• The n-axis is perpendicular to the t-axis

with the positive direction toward the
center of curvature of the curve.
• The coordinate n and t will now be used to
describe the velocity v and acceleration a.
• Similarly to the unit vectors i
and j introduced for
rectangular coordinate system,
unit vectors for t-n coordinate
system can be used.

• For this purpose we introduce

unit vector
• et in the t-direction
• en in the n-direction.
• et - directed toward the direction of
motion.
• en-directed toward the center of
curvature of the path.
• During the differential
increment of time dt, the
particle moves a differential
distance ds along the curve
from A to A’.
• With the radius of curvature
of the path at this position
designated by ρ, we see that
ds = ρdβ
velocity
• The magnitude of the velocity is:-
 ds d d
v v   
dt dt dt

• Since it is unnecessary to consider the

differential change in between A and A’,
   
v vet  et ........................(1)
 Acceleration
• The acceleration a of the particle was
defined by:
 dv d
a  vet 
dt dt
• Now differentiate the velocity by applying the
ordinary rule (chain rule) for the differentiation of
the product of a scalar and a vector.
 dv d dv det
a  vet   et  v
dt dt dt dt
  
a v et  v et
• Where the unit vector et now has a
derivative because its direction changes.
 dv det
a  et  v . . . . . . . . . . . (1)
dt dt
 det
• To find the derivative of consider the
dt
following figure
• Using vector addition
e’t = et + ∆et
• Since the magnitude
| e’t |= | et | = 1
• The magnitude of ∆et
| ∆et |= 2 sin ∆ѳ/2
• Dividing both sides by ∆ѳ
2 sin 
e 2
t

 
et
• As ∆ѳ→0,  is tangent to the path;i.e,

perpendicular to et .
• Taking the limit as ∆ѳ→0

et sin 
lim  lim 2 1
  0    0 
2

• The vector obtained in the limit is a unit

vector along the normal to the path of the
particle.
et det
lim  1
  0  d
 det
• But 1.en
d
det
 en   det d .en
d
• Dividing both sides by dt
det d But dѳ = ds/ρ
 .e n
dt dt

• Then det 1 ds det v

 .en   en
dt  dt dt 
• Equation (1) becomes
det dv v2 dv
a v  et  a  .en  .et
dt dt  dt

• We can write
a an en  at et
v2  2  
where,an    andat v  


a a  an2  at2
Note:
• an is always directed towards the center of
curvature of the path.
• at is directed towards the positive t-direction of
the motion if the speed v is increasing and
towards the negative t-direction if the speed v
is decreasing.
• At the inflection2 point in the curve, the normal
v
acceleration, goes to zero since ρ becomes

infinity.
Special case of motion
• Circular2
motion

v
an  v r 
but ρ=r and


an r 2 
dv d   d
at    r   r
dt dt   dt

at r 
  2
a r  et  r  en
• The particle moves along a path
expressed as y = f(x). The radius of
curvature, ρ, at any point on the path can
be calculated from
3
 dy 2  2
1  ( ) 
dx 
 xy 
d2y
dx 2
APPLICATIONS
Cars traveling along a
clover-leaf interchange
experience an
acceleration due to a
change in speed as well
as due to a change in
Example 1
To anticipate the dip and hump in the road the driver of a car applies her brakes to
produce a uniform deceleration. Her speed is 100 km/hr at bottom A of dip and 50
km/hr at top C of hump, which is 120 m along the road from A. if the passenger
expresses total, acceleration 3 m/s2 at A and if the radius of curvature hump at C is
150m, calculate
A. radius of curvature p at A
B. acceleration at inflection pt B.
C. total acceleration at C
Example 2
• The car travels at constant speed from the bottom A of the
dip to the top B of the hump. If the radius of curvature of road
at A is PA 120m and the car acceleration at A is 0.4g,
determine the car speed V, if the acceleration at B must be
limited 0.25g, determine the minimum radius of curvature P B
of the road at B.
Curvilinear motion
Polar coordinate system (r- ѳ)
Polar coordinate(r- ѳ)
• The third description for plane curvilinear
motion.
• Where the particle is located by the radial
distance r from a fixed pole and by an angular
measurement ѳ to the radial line.
• Polar coordinates are particularly useful when
a motion is constrained through the control of
a radial distance and an angular position,
• or when an unconstrained motion is observed
by measurements of a radial distance and an
angular position.
• An arbitrary fixed line,
such as the x-axis, is
used as a reference for
the measurement ѳ.

• Unit vectors er and eѳ

are established in the
positive r and ѳ
directions, respectively.
 
• The position vector r to the particle at A has a
magnitude equal to the radial distance r and
a direction specified by the unit vector er.

• We express the location of the particle at A by

the vector
 
• r r. e r
 Velocity
• The velocity is obtained by differentiating the vector r.
  
dr dr.er dr  der
v   er  r
dt dt dt dt
  
v r .er  r. er
• Where the unit vector er now has a derivative because
its direction changes.
• We obtain the derivation in exactly the same way that
we derived for et.
 der
• To find the derivative of consider the
dt
following figure
• Using vector addition
e’r = er + ∆er
e’ѳ = eѳ + ∆eѳ
• Since the magnitude
|e’r| = |er| = |e’ѳ|= |eѳ| = 1
• The magnitude of ∆er and ∆eѳ
| ∆er|= |∆eѳ| =2 sin ∆ѳ/2
• Dividing both sides by ∆ѳ
2 sin 
e e  2
r
 
  
er
• As ∆ѳ→0,  is perpendicular to er .
Note: As ∆ѳ→0,

er
1.  is directed towards
the positive eѳ direction.

e
2.  is directed towards

the negative er direction.

er e sin 
lim  lim  lim 2 1
• Then, 
  0    0    0
2
• Therefore;
er der
lim  1
  0  
e de
lim  1
  0  
der   
1.e e  der d .e
d
de   
 1.er  er  de  d .er
d
• Dividing both sides by dt, we have
 
der d  der  
 e   .e
dt dt dt
 
de d  de  
 er    .er
dt dt dt

• Therefore, the velocity equation becomes;


dr  der    
v er  r r .er  r. e
dt dt
• Where
 
vr r andv r.
2 2
v  vr  v
 v 
 tan 
1

 vr 
• The r-component of v is merely the rate at
which the vector r stretches.
• The ѳ-component of v is due to the rotation of
r.
Acceleration
• Differentiating the expression for v to obtain
the acceleration a.
 
 dv d 2r d    

a  2   r er  r  e 
dt dt dt  
   
 dr   der dr   d   de
a er  r   e  r e  r 
dt dt dt dt dt

• But from the previous derivation

der   de  
 .e , and   .er
dt dt
• Substituting the above and simplifying
           
  
a  r er  r  e  r  e  r  e  r      er
 
    2 
   

 a  r  r   er   r   2 r   e
   

• Where
   2 
ar  r  r   2
a  a r a
2

 
 a 
   

a  r   2 r    tan 
1

   ar 
• For motion in a circular path
• Velocity
 
v r .er  r. e

Where, r because
0 r=constant

 v r. e

• Acceleration
 
where, r  r 0

  2 
 

 a   r   er   r   e
   
 Example
• The slider P can be moved inward by means of the
string S as the bar OA rotates about the pivot O. the
angular position of bar radius and 2
t is in sec. the
r 0.8  0.1t  0.05t
position of slider is given by .
where r is in meter and t is in sec. determine and
2
0.8  0.1t 
sketch the velocity and acceleration of the slide at
r 0.05t

time t=2sec. Find angle alpha and beta which v and a

make with positive x-axis.
Kinematics of particles
Relative motion
Relative motion
• Relative motion analysis : is the motion
analysis of a particle using moving reference
system coordinate in reference to fixed
reference system.
• In this portion we will confine our
attention to:-
– moving reference systems that translate
but do not rotate.
– The relative motion analysis is limited to
plane motion.
• Note: in this section we need

1.Inertial(fixed) frame of reference.

2.Translating(not rotating) frame of reference.

• Consider two particles A and B that may have
separate curvilinear motion in a given plane
or in parallel planes.
• X,Y : inertial frame of reference
• X,y : translating coordinate system
• Using vector addition:
• position vector of particle B is

r B r A  r B / A

Where: rA, rB – absolute position vectors

rB/A – relative position vector of particle B (B

relative to A or B with respect to A)

• Differentiating the above position vector once
we obtain the velocities and twice to obtain
accelerations. Thus,

- Velocity - Acceleration

dr B d r A d r B/ A dvB dv A dv B/ A
   
dt dt dt dt dt dt
v B v A  v B / A a B a A  a B / A
• Note: In relative motion analysis, we
employed the following two methods,

1. Trigonometric(vector) diagram – A sketch of

the vector triangle is made to reveal the
trigonometry

2. Vector algebra – using unit vector i and j,

express each of the vectors in vector form.
Example 1
• A 350m long train travelling at a constant speed of 40m/s crosses
over a road as shown below. If an automobile A is traveling at
45m/s and is 400m from the crossing at the instant the front of the
train reaches the crossing, determine
a) The relative velocity of the train with respect to the automobile,
and
b) The distance from the automobile to the end of the last car of the
train at the instant.
Example 2
• For the instant represented, car A has a speed of
100km/h, which is increasing at the rate of 8km/h
each second. Simultaneously, car B also has a
speed of 100km/h as it rounds the turn and is
slowing down at the rate of 8km/h each second.
Determine the acceleration that car B appear to
have an observer in car A.
Example 3
• For the instant represented, car A has an acceleration
in the direction of its motion and car B has a speed of
72km/h which is increasing. If the acceleration of B as
observed from A is zero for this instant,
• Determine the acceleration of A and the rate at which
the speed of B is changing.
Example 4
• Airplane A is flying horizontally with a constant speed
of 200km/h and is towing the glider B, which is
gaining altitude. If the tow cable has a length r=60m
and is increasing at the constant rate of 5 degrees
per second, determine the velocity and acceleration
of the glider for the instant when =15
Constrained motion of
connected particles
Constrained motion(dependent
motion)
• Sometimes the position of a particle will depend
upon the position of another or of several
particles.
• If the particles are connected together by an
inextensible ropes, the resulting motion is called
constrained motion
• Considering the figure, cable AB is subdivided into three
segments:
• the length in contact with the
pulley, CD
• the length CA
• the length DB

• It is assumed that, no matter how A and B move, the

length in contact with the pulley is constant.
• We could write:

s A  lCD  s B l AB constant
• Differentiating with respect to time,

ds A dsB
 0
dt dt
v A  v B 0
• Differentiating the velocity equation

a A  a B 0
Important points in this technique:

• Each datum must be defined from a fixed position.

• In many problems, there may be multiple lengths like lCD that

don’t change as the system moves. Instead of giving each of
these lengths a separate label, we may just incorporate them
into an effective length:
• where it’s understood that
l = cable length less the length in contact with the pulley = lAB
– lCD.

s A  s B l constant
• considering the fig, we could
write:
s A  h  2 s B l constant

• where l is the length of the cable

less the red segments that remain
unchanged in length as A and B
move. Differentiating,

v A  2vB 0
a A  2aB 0
• we could also write the length of
the cable by taking another
datum:
s A  h  2( h  s B ) l constant

• Differentiating,

v A  2vB 0
a A  2aB 0
• Consider the fig.,
r2
L x   2 y  r1  b
2

• Since L, r2, r1 and b is

constant, the first and
second time derivatives
0  x  2 y
are:-
0 x  2 y
• Consider the
following figure
LA  y A  2 y D  const.
LB  y B  yC  ( yC  y D )  const.
• NB. Clearly, it is impossible for the
signs of all three terms to be positive
simultaneously.
Example 1
• A women walks on east-west street at speed of
4mi/hr. the wind blows out of the north west as
shown at speed of 3mi/hr. determine the velocity
of the wind relative to the street. Express your
result in both in terms of unit vector iand j and as
magnitudes and compass direction.
 Part III
Kinetics of particles
Kinetics of particles

• It is the study of the relations existing

between the forces acting on body, the mass
of the body, and the motion of the body.
• It is the study of the relation between
unbalanced forces and the resulting motion.
• Newton ’s first law and third law are sufficient

for studying bodies at rest (statics) or bodies

in motion with no acceleration.

• When a body accelerates ( change in velocity

magnitude or direction) Newton ’s second law

is required to relate the motion of the body to

the forces acting on it.

Kinetics problems

• Force-mass-acceleration method

• Work and energy principles

• Impulse and momentum method

Force, mass and acceleration

• Newton ’s Second Law: If the resultant force

acting on a particle is not zero the particle will
have an acceleration proportional to the
magnitude of resultant and in the direction of
the resultant.
• The basic relation between force and
acceleration is found in Newton's second law
of motion and its verification is entirely
experimental.
• Consider a particle subjected to constant
forces
F1 F2 F
 ...  const
a1 a2 a

• We conclude that the constant is a measure

of some property of the particle that does not
change.
• This property is the inertia of the particle
which is its resistance to rate of change of
velocity.
• The mass m is used as a quantitative
measure of inertia, and therefore the
experimental relation becomes,
F=ma
• The above relation provides a complete
formulation of Newton's second law; it
expresses not only that the magnitude F and
a are proportional but also that the vector F
and a have the same direction.
Types of dynamics problems
• Acceleration is known from kinematics
conditions
Determine the corresponding forces
• Forces acting on the particle are specified
(Forces are constant or functions F( t, s, v, …)
Determine the resulting motion
Equation of motion and solution of problems
• When a particle of mass m acted upon by
several forces. The Newton’s second law can
be expressed by the equation

 F ma
• To determine the acceleration we must use
the analysis used in kinematics, i.e
• Rectilinear motion
• Curvilinear motion
Rectilinear Motion
• If we choose the x-direction, as the direction
of the rectilinear motion of a particle of mass
m, the acceleration in the y and z direction
will be zero, i.e
F x
ma x
F y
0
F z
0
• Generally,
F x ma x
F y ma y
maZ F Z
• Where the acceleration and resultant force
are given by

a a x i  a y j  a z k  F F i  F j  F k
x y z

 F   F   ( F )
2 2 2
 ( Fz ) 2
2
a  ax  a y  az x y
2
Curvilinear motion
• In applying Newton's second law, we shall
make use of the three coordinate descriptions
of acceleration in curvilinear motion.
Rectangular coordinates
F x
max
F y
ma y
 
Where a x x anda y y
Normal and tangential coordinate
F n man
F t mat
 2 v2 
• Where an    

, at v
Polar coordinates
 F ma
r r

 F ma
 2   
• Where a  r  r 

and an r   2 r 
r
Examples
Example 1
• Block A has a mass of 30kg and block B has a
mass of 15kg. The coefficient of friction between
 s 0are
all plane surfaces of contact .15  k 0.10
and
. Knowing that Ѳ=300 and that the magnitude of
the force P applied to block A is 250N, determine

a) The acceleration of block A ,and

b) The tension in the cord

Example 2
• A small vehicle enters the top A of the circular
path with a horizontal velocity vo and gathers
speed as it moves down the path.
• Determine an expression for the angle β to the
position where the vehicle leaves the path and
becomes a projectile. Evaluate your expression
for vo=0. Neglect friction and treat the vehicle as
a particle
Exercise(problem 3/69)
• The slotted arm revolves in the horizontal plane about
the fixed vertical axis through point O. the 2kg slider C
is drawn toward O at the constant rate of 50mm/s by
pulling the cord S. at the instant for which r=225mm,
the arm has a counterclocke wise angular velocity
w=6rad/s and is slowing down at the rate of 2rad/s2.
For this instant, determine the tension T in the cord
and the magnitude N of the force exerted on the slider
by the sides of the smooth radial slot. Indicate which
side, A or B of the slot contacts the slider.
Exercise (problem 3/43)
• The sliders A and B are connected by a light
rigid bar and move with negligible friction in the
slots, both of which lie in a horizontal plane. For
the positions shown, the velocity of A is 0.4m/s
to the right. Determine the acceleration of each
slider and the force in the bar at this instant.
Exercise (problem 3/36)

• Determine the accelerations of bodies A and

B and the tension in the cable due to the
application of the 250N force. Neglect all
friction and the masses of the pulleys.