Scribd
Upload
7 views10 pages

Lecture QA Bridges

Uploaded by

Yagnavajjala Ramesh
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PPTX, PDF, TXT or read online on Scribd
7 views10 pages

Lecture QA Bridges

Uploaded by

Yagnavajjala Ramesh
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PPTX, PDF, TXT or read online on Scribd
You are on page 1/ 10

1.

In the bridge circuit shown in the figure, under balanced condition, the values of R and C respectively, are

(A) 1.010 Ω and 19.802 µF


(B) 9.901 Ω and 0.505 µF
(C) 19.802 Ω and 1.01 µF
(D) 39.604 Ω and 2.02 µF
2. In the figure shown, R = 4.5 kΩ, ΔR = 1.5 kΩ, and INA is assumed to be ideal. The equivalent resistance
between A and B is ____ kΩ (rounded off to nearest integer).

(A) 2
(B) 3
(C) 5
(D) 4
3. When the bridge given below is balanced, the current through the resistor Ra is _____mA (rounded off to
nearest integer).

(A) 1
(B) 2
(C) 3
(D) 4
4. Four strain gauges RA, RB, RC and RD, each with nominal resistance R, are connected in a bridge configuration.
When a force is applied, RA and RD increase by ∆R and RB and RC decrease by ∆R as shown. A potentiometer
with total resistance Rv is connected as shown. If R = 100 Ω, and ∆R = 1 Ω, the minimum value of resistance Rv
required to balance the bridge is ______Ω (rounded off to nearest integer).

(A) 1
(B) 2
(C) 3
(D) 4
5. The bridge shown is balanced when 𝑅1= 100 Ω, 𝑅2 = 210 Ω, 𝐶 = 2.9 μF, and 𝑅4 = 50 Ω. The 2 kHz sine-
wave generator supplies a voltage of 10 Vp-p. The value of 𝐿 (in millihenry) ranges in _______.

(A) [13.30,13.50]
(B) [14.40,14.60]
(C) [15.50,15.70]
(D) [16.70,16.80]
6. In the Wheatstone bridge circuit shown, 𝑅1=1.5 kΩ and 𝑅2 =𝑅3 =𝑅4 =1 kΩ. The switch is initially open and the
voltage between the points C and D is 𝑉𝐶𝐷 . Upon closing the switch at 𝑡=0, the resistance in the arm AD changes
by an amount 𝛿𝑅1 , and the voltage between C and D changes by 𝛿𝑉𝐶𝐷 . The sensitivity of the bridge (in
volt/kiloohm), defined as |𝛿𝑉𝐶𝐷 /𝛿𝑅1| , is in the range ________ .

(A) [1.22,1.32]
(B) [1.62,1.72]
(C) [2.22,2.32]
(D) [2.62,2.72]
7. In the bridge circuit shown, the voltmeter V showed zero when the value of the resistors are 𝑅1=100 Ω
and 𝑅2 =110Ω, 𝑅3 =90Ω. If (𝑅1/𝑅2)= (𝑅A/𝑅B), The value of R4 in ohm is ________.

(A) 93
(B) 95
(C) 97
(D) 99
8. In the Maxwell-Wien bridge shown, the detector D reads zero when C1 = 100nF & R 1 = 100kΩ. The Q factor of
the coil is ______.

(A) 10
(B) 100
(C) 1000
(D) 0
9. The parallel resistance-capacitance bridge shown below has a standard capacitance value of C1 = 0.1 μF and a
resistance value of R3 = 10 kΩ. The bridge is balanced at a supply frequency of 100 Hz for R1 = 375 kΩ, R3 = 10
kΩ, and R4 = 14.7 kΩ. The value of the dissipation factor D = 1/(ωRpC p) of the parallel combination of Cp and Rp
is __________. (Answer should be rounded off to THREE decimal places)
10. The inductance of a coil is measured using the bridge shown in the figure. Balance (D = 0) is obtained with
C1 = 1 nF, R1 = 2.2 MΩ, R2 = 22.2 kΩ, R4 = 10 kΩ. The value of the inductance Lx (in mH) is in the range
______.

(A) [101,103]
(B) [121,123]
(C) [201, 203]
(D) [221,223]

You might also like