Serial Interfaces, Part Deux

-I2C and SPI

December 4, 2002
Presented by Eugene Ho
 Introduction
Serial Interfaces, part two

I2C and SPI

• Serial communication protocols
• Meant for short distances “inside the box”
• Low complexity
• Low cost
• Low speed ( a few Mbps at the fastest )

• To be discussed: Applications, protocols, tradeoffs, AVR

support

2
 What is I2C?
Serial Interfaces, part two

• Shorthand for an “Inter-integrated circuit” bus

• Developed by Philips Semiconductor for TV sets in the 1980’s
• I2C devices include EEPROMs, thermal sensors, and real-time
clocks
• Used as a control interface to signal processing devices that
have separate data interfaces, e.g. RF tuners, video decoders
and encoders, and audio processors.
• I2C bus has three speeds:
– Slow (under 100 Kbps)
– Fast (400 Kbps)
– High-speed (3.4 Mbps) – I2C v.2.0
• Limited to about 10 feet for moderate speeds

3
 I2C Bus Configuration
Serial Interfaces, part two

• 2-wire serial bus – Serial data (SDA) and Serial clock (SCL)
• Half-duplex, synchronous, multi-master bus
• No chip select or arbitration logic required
• Lines pulled high via resistors, pulled down via open-drain drivers
(wired-AND)

4
 I2C Protocol
Serial Interfaces, part two

1. Master sends start condition (S) and controls the clock signal
2. Master sends a unique 7-bit slave device address
3. Master sends read/write bit (R/W) – 0 - slave receive, 1 - slave transmit
4. Receiver sends acknowledge bit (ACK)
5. Transmitter (slave or master) transmits 1 byte of data

5
 I2C Protocol (cont.)
Serial Interfaces, part two

6. Receiver issues an ACK bit for the byte received

7. Repeat 5 and 6 if more bytes need to be transmitted.
8.a) For write transaction (master transmitting), master issues stop
condition (P) after last byte of data.
8.b) For read transaction (master receiving), master does not acknowledge
final byte, just issues stop condition (P) to tell the slave the transmission
is done

6
 I2C Signals
Serial Interfaces, part two

• Start – high-to-low transition of the SDA line while SCL line is high
• Stop – low-to-high transition of the SDA line while SCL line is high
• Ack – receiver pulls SDA low while transmitter allows it to float high
• Data – transition takes place while SCL is slow, valid while SCL is high

7
 I2C Features
Serial Interfaces, part two

• “Clock stretching” – when the slave (receiver) needs more

time to process a bit, it can pull SCL low. The master waits
until the slave has released SCL before sending the next bit.

• “General call” broadcast – addresses every device on the bus

• 10-bit extended addressing for new designs. 7-bit addresses

all exhausted

8
 AVR Support for I2C
Serial Interfaces, part two

• Atmel calls it “Two-wire Serial Interface” (or TWI)

• Supported by all AVR 8-bit μC except ATTiny and AT90

ATmega323 TWI mode when TWEN in TWCR is set:

• PC0=SCL, PC1=SDA
• TWBR – sets bit rate
• TWCR – controls start, stop, ack generation, indicates M/S, T/R
• TWDR – contains byte transmitted/received
• TWAR – contains slave address
• TWSR – indicates status of TWI Bus (start condition
transmitted, ACK received, … 26 total states)

9
 I2C Tradeoffs
Serial Interfaces, part two

Advantages:
• Good for communication with on-board devices that are accessed
occasionally.
• Easy to link multiple devices because of addressing scheme
• Cost and complexity do not scale up with the number of devices

Disadvantages:
• The complexity of supporting software components can be higher
than that of competing schemes ( for example, SPI ).

10
 What is SPI?
Serial Interfaces, part two

• Shorthand for “Serial Peripheral Interface”

• Defined by Motorola on the MC68HCxx line of microcontrollers
• Generally faster than I2C, capable of several Mbps

Applications:
• Like I2C, used in EEPROM, Flash, and real time clocks
• Better suited for “data streams”, i.e. ADC converters
• Full duplex capability, i.e. communication between a codec and
digital signal processor

11
 SPI Bus Configuration
Serial Interfaces, part two

• Synchronous serial data link operating at full duplex

• Master/slave relationship
• 2 data signals:
– MOSI – master data output, slave data input
– MISO – master data input, slave data output
• 2 control signals:
– SCLK – clock
– /SS – slave select (no addressing)

12
 SPI vs. I2C
Serial Interfaces, part two

• For point-to-point, SPI is simple and efficient

– Less overhead than I2C due to lack of addressing, plus SPI is full duplex.
• For multiple slaves, each slave needs separate slave select signal
– More effort and more hardware than I2C

13
 SPI Protocol
Serial Interfaces, part two

• 2 Parameters, Clock Polarity (CPOL) and Clock Phase (CPHA),

determine the active edge of the clock
CPOL CPHA Active edge
0 0 Rising
0 1 Falling
1 0 Falling
1 1 Rising

• Master and slave must agree on parameter pair values in order to

communicate

14
 SPI Protocol (cont.)
Serial Interfaces, part two
• SPI interface defines only the communication lines and the clock
edge
• There is no specified flow control! No acknowledgement mechanism
to confirm receipt of data

• Hardware realization is usually done with a simple shift register

15
 AVR Support for SPI
Serial Interfaces, part two

• Supported by all AVR 8-bit μC except ATTiny and some AT90s

ATmega323 - SPI mode when SPE bit in SPCR is set:

• PB6=MISO, PB5=MOSI, PB7=SCK, PB4=/SS
• SPCR – sets bit rate, CPOL, CPHA, M/S
• SPDR – used for data transfer to and from SPI shift register

• For multiple slaves, must employ “bit-banging”. Use software to

control serial communication at general-purpose I/O pins.

16
 Summary
Serial Interfaces, part two

• I2C and SPI provide good support for

communication with slow peripheral devices that are
accessed intermittently, mainly EEPROMs and real-
time clocks

• I2C easily accommodates multiple devices on a

single bus.

• SPI is faster, but gets complicated when there is

more than one slave involved.

17
 References
Serial Interfaces, part two

I2C:
• http://www-us2.semiconductors.philips.com/acrobat/various/
I2C_BUS_SPECIFICATION_1995.pdf
• http://www.esacademy.com/faq/i2c/index.htm
• http://www.embedded.com/story/OEG20020528S0057

SPI:
• MC68HC11 manual
• http://www.mct.net/faq/spi.html
• http://links.epanorama.net/links/serialbus.html
• http://www.embedded.com/story/OEG20020124S0116

18