A PROJECT ON Portable Humidifier With
Internet Of Things (iot) Applications
Department Of Information Technology
Under the supervision of
PRESENTED By
Hafizur Rahman
Anshuman Dey – 2021ITB004 (IT)
Professor
Arindam Mondal – 2021ITB007 (IT)
Department of Information
Shubhayu Shome – 2021ITB108 (IT)
Technology
INDEX
I. Introduction
II. List of Components used
Arduino UNO Board
DHT11 Sensor
5V Relay Module
OLED Display
Ultrasonic Humidifier
III. Circuit Diagram
IV. Working
V. Observation
VI. Conclusion
VII. Future Scope and Uses
Page No. 1
INTRODUCTION
What is Internet Of Things
•(IOT)?
Network of
Physical Objects
• Feature an IP
address and
internet
connectivity
• Allow
communication
between IoT
enabled objects
Page No. 2
HUMIDIFIER
• Increases moisture
content of air
• Used to increase
moisture of carrier
gas
• Comfort during air
conditioning
Page No. 3
GOAL OF THE PROJECT
OUR GOAL IS TO CREATE AN HUMIDIFIER
USING IOT WHICH SENSES THE
TEMPERATURE AND HUMIDITY AROUND
AND REGULATES BY THE HUMIDIFIER
FUNCTION
Page No. 4
List Of The Components
Used In This Project
Page No. 5
ARDUINO UNO BOARD
• Open source
microcontroller
board
• Based on Microchip
ATMega328P
• Used to receive
input data and
process and
generate a response
according to
program
• It operates at a
frequency of 16MHz
Page No. 6
DHT11 SENSOR
• Commonly used for
sensing humidity and
temperature
• Uses a capacitive
humidity sensing
element
• Uses a thermistor for
sensing temperature
Page No. 7
5V RELAY MODULE
• electromechanical
device that uses an
electric current to
open or close the
contacts of a switch
• Works with a low
level trigger voltage
of 5V DC
Page No. 8
OLED DISPLAY
• Organic
electroluminescent diode
• Emissive electroluminesce
nt layer is a film of organic
PROJECT
compound
Temp: 28.1°C • emits light in response to
an electric current
HUM: 85%
Page No. 9
ULTRASONIC HUMIDIFIER
• Produce fine droplets of
water at room
temperature
• Uses piezo electronic
transducer to create high
frequency mechanical
oscillation on a film of
water
Page No. 10
CIRCUIT DIAGRAM
Page No. 11
WORKING
Page No. 12
WORKING
Page No. 13
OBSERVATION
• Humidity<=90
• Normally Open pin –
Allows load to humidifier
• Humidifier: ON
Page No. 14
OBSERVATION
• Humidity>90
• Normally Open pin –
Blocks load to humidifier
• Humidifier: OFF Page No. 15
CONCLUSION
• Can be directly supplied with current through cable or be used with
battery.
• Operates automatically
• Reads room temperature and humidity
• Transmits data Uno Board
• When humidity is above 90% circuit is opened, humidifier stops
operating
• When humidity is below 90% circuit is closed, humidifier spray
water droplets to bring humidity to the optimum level
Page No. 16
USES IN DAILY LIFE AND FUTURE
SCOPE
Steamer for nasal Household humidifier – Humidifier in
treatment maintain moisture greenhouse –
level Maintain moisture for
Page No. 17
REFERENCES
1. Project on Automatic Portable Humidifier using Arduino by
Debasis Parida
2. Performance Evaluation of Portable Mist Humidifier by
M.Mahesh, P.Thangavel,2020
3. Principle of Arduino by Leo Louis,2018.
4. Images have been taken from Google
5. Websites used for reference are Arduino.com and
CircuitDigest.com
Page No. 18
Questions
&
Answers
Page No. 19
THANK
YOU
Page No. 20
