CO2015

Exercise – BJT
Electronic Circuit Component – Applications And
Circuits

▪ When a transistor is used as a switch, it is stable

in which two distinct regions?
▪ saturation and active
▪ active and cutoff
▪ saturation and cutoff
▪ none of the above

2
Electronic Circuit Component – Applications And
Circuits

▪ For a silicon transistor, when a base-emitter

junction is forward-biased, it has a nominal
voltage drop of
▪ 0.7
▪ 0.3
▪ 0.2
▪ VCC

3
Electronic Circuit Component – Applications And
Circuits

▪ A certain BJT has IB = 167uA, IC = 15mA, the

amplifier DC factor is:
▪ 15
▪ 167
▪ 90
▪ All are not correct

4
Electronic Circuit Component – Applications And
Circuits

▪ Refer to the given figure. The most probable cause

of trouble, if any, from these voltage
measurements is

5
Electronic Circuit Component – Applications And
Circuits

▪ Refer to the given figure. The most probable cause

of trouble, if any, from these voltage
measurements is

6
Electronic Circuit Component – Applications And
Circuits

▪ Refer to this figure. If VCE = 0.2 V, IC(sat) is

7
Electronic Circuit Component – Applications And
Circuits

▪ Refer to this figure. Determine the minimum value

of IB that will produce saturation (VCE(sat) = 0.2V).

8
Electronic Circuit Component – Applications And
Circuits

▪ Refer to this figure. The value of VBC is

9
 CO2015

Exercise – FET
Electronic Circuit Component – Applications And
Circuits

▪ Refer to the given figure. Calculate the value of

VDS

1
Electronic Circuit Component – Applications And
Circuits

Answer
▪ 2V

1
Electronic Circuit Component – Applications And
Circuits

▪ Refer to figure shown below. Determine the

value of VS.

1
Electronic Circuit Component – Applications And
Circuits

Answer
▪ 6V

1
Electronic Circuit Component – Applications And
Circuits

▪ Refer to the given figure. ID = 6 mA.

Calculate the value of VDS

1
Electronic Circuit Component – Applications And
Circuits

▪ -9V

▪ In general VDS= VDD-(ID*RD)

But in figure direction of FET transistor is out of
drain so, Id becomes negative .

1
Electronic Circuit Component – Applications And
Circuits

▪ Refer to the given figure. ID = 6 mA. Calculate the

value of VDS

1
Electronic Circuit Component – Applications And
Circuits

Answer
▪ 6V

2
Electronic Circuit Component – Applications And
Circuits

▪ Refer to figure given below. Determine the value

of VGS

2
Electronic Circuit Component – Applications And
Circuits

Answer
▪ -6V

2
Electronic Circuit Component – Applications And
Circuits

▪ Refer to figure show below. Calculate the value of

VD

2
Electronic Circuit Component – Applications And
Circuits

Answer
▪ 8V

2
Electronic Circuit Component – Applications And
Circuits

▪ For a JFET, the value of VDS at which ID becomes

essentially constant is the
▪ pinch-off voltage.
▪ cutoff voltage.
▪ breakdown voltage.
▪ ohmic voltage.

2
Electronic Circuit Component – Applications And
Circuits

Answer: A

2
Electronic Circuit Component – Applications And
Circuits

▪ The value of VGS that makes ID approximately zero

is the
▪ Pinch-off voltage
▪ Cut-off voltage
▪ Breakdown voltage

2
Electronic Circuit Component – Applications And
Circuits

Answer
▪B

2
Electronic Circuit Component – Applications And
Circuits

▪ The ________ has a physical channel between the

drain and source.
▪ DFET
▪ EFET
▪ VFET

2
Electronic Circuit Component – Applications And
Circuits

Answer: A

3
Electronic Circuit Component – Applications And
Circuits

▪ What type(s) of gate-to-source voltage(s) can a

depletion MOSFET (D-MOSFET) operate with?
▪ Zero
▪ Positive
▪ Negative
▪ All of them

3
Electronic Circuit Component – Applications And
Circuits

▪ Midpoint bias for a D-MOSFET is ID = ________,

obtained by setting VGS = 0
▪ IDSS / 2
▪ IDSS / 3.4
▪ IDSS

3
Electronic Circuit Component – Applications And
Circuits

▪ Identify D-FET p channel

3
Electronic Circuit Component – Applications And
Circuits

Answer
▪B

3
Electronic Circuit Component – Applications And
Circuits

▪ Determine VGS and ID

3
Electronic Circuit Component – Applications And
Circuits

Answer
▪ Determine the Load line
▪ ID = 0

▪ ID = IDSS

▪ Q is the intersection point of the

load line & transfer curve.

• ID = 5.07 mA
• VGS = -2.3V

3
Electronic Circuit Component – Applications And
Circuits

▪ Determine VGS and ID for the given JFET, where

▪ IDSS = 5mA and VGS(off) = -4V

3
 CO2015

Exercise – Op Amp
Electronic Circuit Component – Applications And
Circuits

▪ Calculate the output gain of the circuit if R1 =

100(Ohm) and Rf = 1(KOhm)

3
Electronic Circuit Component – Applications And
Circuits

Answer
▪ 11

4
Electronic Circuit Component – Applications And
Circuits

▪ Refer to the given figure. A dc input signal of –50

mV is applied. You would measure ________ from
the inverting input to ground.
▪ 50mV
▪ 1.05V
▪ -1.05V
▪ -50mV

4
Electronic Circuit Component – Applications And
Circuits

▪ Calculate the input voltage if the final output is

10.08 V
▪ 0.168V