Chapter 3

Data and Signals

3.1 Copyright © The McGraw-Hill Companies, Inc. Permission required for reproduction or display.
 Note

To be transmitted, data must be

transformed to electromagnetic signals.

3.2
 3-1 ANALOG AND DIGITAL
Data can be analog or digital.
The term analog data refers to information that is
continuous;
digital data refers to information that has discrete
states.
.

Topics discussed in this section:

Analog and Digital Data
Analog and Digital Signals
Periodic and Nonperiodic Signals

3.3
 Note

Data can be analog or digital.

Analog data are continuous and take
continuous values.
Digital data have discrete states and
take discrete values.

3.4
 Note

Signals can be analog or digital.

Analog signals can have an infinite
number of values in a range; digital
signals can have only a limited
number of values.

3.5
 Figure 3.1 Comparison of analog and digital signals

3.6
 Note

In data communications, we commonly

use periodic analog signals and
nonperiodic digital signals.

3.7
 3-2 PERIODIC ANALOG SIGNALS
Periodic analog signals can be classified as:
• Simple periodic analog signal
• A sine wave, cannot be decomposed into simpler
signals.
•Composite periodic analog signal
• Composed of multiple sine waves.

Topics discussed in this section:

Sine Wave
Wavelength
Time and Frequency Domain
Composite Signals
Bandwidth

3.8
 Figure 3.2 A sine wave

3.9
 Figure 3.3 Two signals with the same phase and frequency,
but different amplitudes

3.10
 Example 3.2

The voltage of a battery is a constant; this constant value

can be considered a sine wave, as we will see later. For
example, the peak value of an AA battery is normally
1.5 V.

3.11
 Note

Frequency and period are the inverse of

each other.

3.12
 Figure 3.4 Two signals with the same amplitude and phase,
but different frequencies

3.13
 Table 3.1 Units of period and frequency

3.14
 Example 3.3

The power we use at home has a frequency of 60 Hz.

The period of this sine wave can be determined as
follows:

3.15
 Example 3.4

Express a period of 100 ms in microseconds.

Solution
From Table 3.1 we find the equivalents of 1 ms (1 ms is
10−3 s) and 1 s (1 s is 106 μs). We make the following
substitutions:.

3.16
 Example 3.5

The period of a signal is 100 ms. What is its frequency in

kilohertz?

Solution
First we change 100 ms to seconds, and then we
calculate the frequency from the period (1 Hz = 10 −3
kHz).

3.17
 Note

Frequency is the rate of change with

respect to time.

Change in a short span of time

means high frequency.

Change over a long span of

time means low frequency.

3.18
 Note

If a signal does not change at all, its

frequency is zero.
If a signal changes instantaneously, its
frequency is infinite.

3.19
 Note

Phase describes the position of the

waveform relative to time 0.

3.20
 Figure 3.5 Three sine waves with the same amplitude and frequency,
but different phases

3.21
 Example 3.6

A sine wave is offset 1/6 cycle with respect to time 0.

What is its phase in degrees and radians?

Solution
We know that 1 complete cycle is 360°. Therefore, 1/6
cycle is

3.22
 Figure 3.6 Wavelength and period

3.23
 Figure 3.7 The time-domain and frequency-domain plots of a sine wave

3.24
 Note

A complete sine wave in the time

domain can be represented by one
single spike in the frequency domain.

3.25
 Example 3.7

The frequency domain is more compact and

useful when we are dealing with more than one
sine wave. For example, Figure 3.8 shows three
sine waves, each with different amplitude and
frequency. All can be represented by three
spikes in the frequency domain.

3.26
 Figure 3.8 The time domain and frequency domain of three sine waves

3.27
 Note

A single-frequency sine wave is not

useful in data communications;
we need to send a composite signal, a
signal made of many simple sine waves.

3.28
 Note

According to Fourier analysis, any

composite signal is a combination of
simple sine waves with different
frequencies, amplitudes, and phases.
Fourier analysis is discussed in
Appendix C.

3.29
 Note

If the composite signal is periodic, the

decomposition gives a series of signals
with discrete frequencies;
if the composite signal is nonperiodic,
the decomposition gives a combination
of sine waves with continuous
frequencies.

3.30
 Example 3.8

Figure 3.9 shows a periodic composite signal with

frequency f. This type of signal is not typical of those
found in data communications. We can consider it to be
three alarm systems, each with a different frequency.
The analysis of this signal can give us a good
understanding of how to decompose signals.

3.31
 Figure 3.9 A composite periodic signal

3.32
 Figure 3.10 Decomposition of a composite periodic signal in the time and
frequency domains

3.33
 Example 3.9

Figure 3.11 shows a nonperiodic composite signal. It

can be the signal created by a microphone or a telephone
set when a word or two is pronounced. In this case, the
composite signal cannot be periodic, because that
implies that we are repeating the same word or words
with exactly the same tone.

3.34
 Figure 3.11 The time and frequency domains of a nonperiodic signal

3.35
 Note

The bandwidth of a composite signal is

the difference between the
highest and the lowest frequencies
contained in that signal.

3.36
 Figure 3.12 The bandwidth of periodic and nonperiodic composite signals

3.37
 Example 3.10

If a periodic signal is decomposed into five sine waves

with frequencies of 100, 300, 500, 700, and 900 Hz, what
is its bandwidth? Draw the spectrum, assuming all
components have a maximum amplitude of 10 V.
Solution
Let fh be the highest frequency, fl the lowest frequency,
and B the bandwidth. Then

The spectrum has only five spikes, at 100, 300, 500, 700,
and 900 Hz (see Figure 3.13).
3.38
 Figure 3.13 The bandwidth for Example 3.10

3.39
 Example 3.11

A periodic signal has a bandwidth of 20 Hz. The highest

frequency is 60 Hz. What is the lowest frequency? Draw
the spectrum if the signal contains all frequencies of the
same amplitude.
Solution
Let fh be the highest frequency, fl the lowest frequency,
and B the bandwidth. Then

The spectrum contains all integer frequencies. We show

this by a series of spikes (see Figure 3.14).
3.40
 Figure 3.14 The bandwidth for Example 3.11

3.41
 Example 3.12

A nonperiodic composite signal has a bandwidth of 200

kHz, with a middle frequency of 140 kHz and peak
amplitude of 20 V. The two extreme frequencies have an
amplitude of 0. Draw the frequency domain of the
signal.

Solution
The lowest frequency must be at 40 kHz and the highest
at 240 kHz. Figure 3.15 shows the frequency domain
and the bandwidth.

3.42
 Figure 3.15 The bandwidth for Example 3.12

3.43
 Example 3.13

An example of a nonperiodic composite signal is the

signal propagated by an AM radio station. In the United
States, each AM radio station is assigned a 10-kHz
bandwidth. The total bandwidth dedicated to AM radio
ranges from 530 to 1700 kHz. We will show the rationale
behind this 10-kHz bandwidth in Chapter 5.

3.44
 Example 3.14

Another example of a nonperiodic composite signal is

the signal propagated by an FM radio station. In the
United States, each FM radio station is assigned a 200-
kHz bandwidth. The total bandwidth dedicated to FM
radio ranges from 88 to 108 MHz. We will show the
rationale behind this 200-kHz bandwidth in Chapter 5.

3.45
 Example 3.15

Another example of a nonperiodic composite signal is

the signal received by an old-fashioned analog black-
and-white TV. A TV screen is made up of pixels. If we
assume a resolution of 525 × 700, we have 367,500
pixels per screen. If we scan the screen 30 times per
second, this is 367,500 × 30 = 11,025,000 pixels per
second. The worst-case scenario is alternating black and
white pixels. We can send 2 pixels per cycle. Therefore,
we need 11,025,000 / 2 = 5,512,500 cycles per second, or
Hz. The bandwidth needed is 5.5125 MHz.

3.46
 3-3 DIGITAL SIGNALS
In addition to being represented by an analog signal,
information can also be represented by a digital signal.
For example, a 1 can be encoded as a positive voltage
and a 0 as zero voltage. A digital signal can have more
than two levels. In this case, we can send more than 1 bit
for each level.

Topics discussed in this section:

Bit Rate
Bit Length
Digital Signal as a Composite Analog Signal
Application Layer
3.47
 Figure 3.16 Two digital signals: one with two signal levels and the other
with four signal levels

3.48
 Note

Appendix C reviews information about

Appendix C reviews information about exponential and logarithmic

exponential and functions.

logarithmic functions.

3.49
 Example 3.16

A digital signal has eight levels. How many bits are

needed per level? We calculate the number of bits from
the formula

Each signal level is represented by 3 bits.

3.50
 Example 3.17

A digital signal has nine levels. How many bits are

needed per level? We calculate the number of bits by
using the formula. Each signal level is represented by
3.17 bits. However, this answer is not realistic. The
number of bits sent per level needs to be an integer as
well as a power of 2. For this example, 4 bits can
represent one level.

3.51
 Example 3.18

Assume we need to download text documents at the rate

of 100 pages per second. What is the required bit rate of
the channel?
Solution
A page is an average of 24 lines with 80 characters in
each line. If we assume that one character requires 8
bits, the bit rate is

100x24x80x8=1536000bps=1.536Mbps

3.52
 Example 3.19

A digitized voice channel, as we will see in Chapter 4, is

made by digitizing a 4-kHz bandwidth analog voice
signal. We need to sample the signal at twice the highest
frequency (two samples per hertz). We assume that each
sample requires 8 bits. What is the required bit rate?

Solution
The bit rate can be calculated as

3.53
 Example 3.20

What is the bit rate for high-definition TV (HDTV)?

Solution
HDTV uses digital signals to broadcast high quality
video signals. The HDTV screen is normally a ratio of
16 : 9. There are 1920 by 1080 pixels per screen, and the
screen is renewed 30 times per second. Twenty-four bits
represents one color pixel.

The TV stations reduce this rate to 20 to 40 Mbps

through compression.
3.54
 Figure 3.17 The time and frequency domains of periodic and nonperiodic
digital signals

3.55
 Figure 3.18 Baseband transmission

3.56
 3-4 TRANSMISSION IMPAIRMENT

Signals travel through transmission media, which are not

perfect. The imperfection causes signal impairment. This
means that the signal at the beginning of the medium is
not the same as the signal at the end of the medium.
What is sent is not what is received. Three causes of
impairment are attenuation, distortion, and noise.

Topics discussed in this section:

Attenuation
Distortion
Noise

3.57
 Figure 3.25 Causes of impairment

3.58
 Figure 3.26 Attenuation

3.59
 Example 3.26

Suppose a signal travels through a transmission medium

and its power is reduced to one-half. This means that P 2
is (1/2)P1. In this case, the attenuation (loss of power)
can be calculated as

A loss of 3 dB (–3 dB) is equivalent to losing one-half

the power.
3.60
 Example 3.27

A signal travels through an amplifier, and its power is

increased 10 times. This means that P2 = 10P1 . In this
case, the amplification (gain of power) can be calculated
as

3.61
 Example 3.28

One reason that engineers use the decibel to measure the

changes in the strength of a signal is that decibel
numbers can be added (or subtracted) when we are
measuring several points (cascading) instead of just two.
In Figure 3.27 a signal travels from point 1 to point 4. In
this case, the decibel value can be calculated as

3.62
 Figure 3.27 Decibels for Example 3.28

3.63
 Example 3.29

Sometimes the decibel is used to measure signal power

in milliwatts. In this case, it is referred to as dBm and is
calculated as dBm = 10 log10 Pm , where Pm is the power in
milliwatts. Calculate the power of a signal with dB m =
−30.

Solution
We can calculate the power in the signal as

3.64
 Example 3.30

The loss in a cable is usually defined in decibels per

kilometer (dB/km). If the signal at the beginning of a
cable with −0.3 dB/km has a power of 2 mW, what is the
power of the signal at 5 km?
Solution
The loss in the cable in decibels is 5 × (−0.3) = −1.5 dB.
We can calculate the power as

3.65
 Figure 3.28 Distortion

3.66
 Figure 3.29 Noise

3.67
 Example 3.31

The power of a signal is 10 mW and the power of the

noise is 1 μW; what are the values of SNR and SNRdB ?

Solution
The values of SNR and SNRdB can be calculated as
follows:

3.68
 Example 3.32

The values of SNR and SNRdB for a noiseless channel

are

We can never achieve this ratio in real life; it is an ideal.

3.69
 3-6 PERFORMANCE

One important issue in networking is the performance of

the network—how good is it? We discuss quality of
service, an overall measurement of network performance,
in greater detail in Chapter 24. In this section, we
introduce terms that we need for future chapters.

Topics discussed in this section:

Bandwidth
Throughput
Latency (Delay)
Bandwidth-Delay Product
3.70
 Note
In networking, we use the term
bandwidth in two contexts.
❏ The first, bandwidth in hertz, refers to
the range of frequencies in a
composite signal or the range of
frequencies that a channel can pass.

❏ The second, bandwidth in bits per

second, refers to the speed of bit
transmission in a channel or link.
3.71
 Example 3.44

A network with bandwidth of 10 Mbps can pass only an

average of 12,000 frames per minute with each frame
carrying an average of 10,000 bits. What is the
throughput of this network?

Solution
We can calculate the throughput as

The throughput is almost one-fifth of the bandwidth in

this case.
3.72
 Example 3.45

What is the propagation time if the distance between the

two points is 12,000 km? Assume the propagation speed
to be 2.4 × 108 m/s in cable.

Solution
We can calculate the propagation time as

The example shows that a bit can go over the Atlantic

Ocean in only 50 ms if there is a direct cable between the
source and the destination.
3.73
 Example 3.46

What are the propagation time and the transmission

time for a 2.5-kbyte message (an e-mail) if the
bandwidth of the network is 1 Gbps? Assume that the
distance between the sender and the receiver is 12,000
km and that light travels at 2.4 × 108 m/s.

Solution
We can calculate the propagation and transmission time
as shown on the next slide:

3.74
 Example 3.46 (continued)

Note that in this case, because the message is short and

the bandwidth is high, the dominant factor is the
propagation time, not the transmission time. The
transmission time can be ignored.

3.75
 Example 3.47

What are the propagation time and the transmission

time for a 5-Mbyte message (an image) if the bandwidth
of the network is 1 Mbps? Assume that the distance
between the sender and the receiver is 12,000 km and
that light travels at 2.4 × 108 m/s.

Solution
We can calculate the propagation and transmission
times as shown on the next slide.

3.76
 Example 3.47 (continued)

Note that in this case, because the message is very long

and the bandwidth is not very high, the dominant factor
is the transmission time, not the propagation time. The
propagation time can be ignored.

3.77
 Figure 3.31 Filling the link with bits for case 1

3.78
 Example 3.48

We can think about the link between two points as a

pipe. The cross section of the pipe represents the
bandwidth, and the length of the pipe represents the
delay. We can say the volume of the pipe defines the
bandwidth-delay product, as shown in Figure 3.33.

3.79
 Figure 3.32 Filling the link with bits in case 2

5
25

3.80
 Note

The bandwidth-delay product defines

the number of bits that can fill the link.

3.81
 Figure 3.33 Concept of bandwidth-delay product

3.82