Drilling Block
1: Feed forward relief pressure adjustment 3: Normal rotation relief pressure 5: Boom relief pressure adjustment
1: Feed forward relief pressure adjustment 3: Normal rotation relief pressure 5: Boom relief pressure adjustment
adjustment
adjustment
4: Reverse rotation relief pressure
2: Feed backward relief pressure adjustment 4: Reverse rotation relief pressure 6: Rotation in H-mode relief pressure
2: Feed backward relief pressure adjustment adjustment 6: Rotation in H-mode relief pressure
adjustment adjustment
adjustment
66 55 22 11 33 44
For each pressure adjustment, set the engine rotation speed in the rated speed shown below:
HCR1200: 2500rpm
HCR1500: 2200rpm
Picture
Picture
To Hydraulic Schematic Back Front page Next
Valve Location
Drilling block
View from right-side
Close
CloseView
View
To Hydraulic Schematic Back Front page Next
Close View Drilling Block
1: Feed forward relief pressure
1: Feed forward relief pressure 3: Normal rotation relief pressure adjustment 5: Boom relief pressure adjustment
adjustment 3: Normal rotation relief pressure adjustment 5: Boom relief pressure adjustment
adjustment
2: Feed backward relief pressure adjustment 4: Reverse rotation relief pressure adjustment 6: Rotation in H-mode relief pressure
2: Feed backward relief pressure adjustment 4: Reverse rotation relief pressure adjustment 6: Rotation in H-mode relief pressure
adjustment
adjustment
11 3 Machine
front
5
6 Machine
rear
2 4
To Hydraulic Schematic Back Front page Next
1: Feed Forward Relief Pressure
Adjustment
1: Feed forward relief pressure adjustment 1/8
Cautions for Adjustment
Check these machine functions prior to adjusting the feed forward relief pressure.
1. Be sure the rod changer manual switch is OFF.
2. Be sure the rod changer is NOT in the Swing IN position.
Rod changer manual operation switch Rod changer Swing IN condition
To Hydraulic Schematic Back Front page Next
1: Feed forward relief pressure adjustment 2/8
1 Plug the hose on the feed forward side.
Backward side
Forward side
Feed motor
To Hydraulic Schematic Back Front page Next
1: Feed forward relief pressure adjustment 3/8
2 Install the pressure gauge to the P1 pressure
port.
Required pressure gauge: 35MPa
To Hydraulic Schematic Back Front page Next
1: Feed forward relief pressure adjustment 4/8
3 Move the safety lock lever downward.
Move the safety lock lever downward.
To Hydraulic Schematic Back Front page Next
1: Feed forward relief pressure adjustment 5/8
4 Move
Movethe
thefeed
feedlever
leverto
tothe
theposition
positionForward
ForwardFeed.
Feed.
For each pressure adjustment, set the engine rotation speed in the rated speed shown below:
HCR1200: 2500rpm
HCR1500: 2200rpm
To Hydraulic Schematic Back Front page Next
1: Feed forward relief pressure adjustment 6/8
5
Turn
Turnthe
thefeed
feedspeed
speedcontrol
controlvalve
valveclockwise
clockwiseall
allthe
theto
tothe
theend.
end.
Counterclockwise: Open Clockwise: Close
Feed speed valve
To Hydraulic Schematic Back Front page Next
1: Feed forward relief pressure adjustment 7/8
6 Adjust the feed relief pressure valve
Clockwise: pressure increase
Counterclockwise: pressure decrease
Pressure setting: 21MPa View from
7
Adjust the adjuster machine
front
To Hydraulic Schematic Back Front page Next
1: Feed forward relief pressure adjustment 8/8
8 Be sure to connect the hose back !
Backward side
Forward side
Feed motor
To Hydraulic Schematic Back Front page Next page
2: Feed Backward Relief Pressure
Adjustment
2: Feed backward relief pressure adjustment 1/7
Caution for Adjustment
Check these machine functions prior to adjusting the feed backward relief pressure.
1. Be sure the rod changer manual switch is OFF.
2. Be sure the rod changer is NOT in the Swing IN position.
Rod changer manual operation switch Rod changer Swing IN condition
To Hydraulic Schematic Back Front page Next
2: Feed backward relief pressure adjustment 2/7
1 Plug the hose on the backward side.
Backward side
Forward side
Feed motor
To Hydraulic Schematic Back Front page Next
2: Feed backward relief pressure adjustment 3/7
2 Install the pressure gauge to the P1 pressure port.
Required pressure gauge: 35MPa
To Hydraulic Schematic Back Front page Next
2: Feed backward relief pressure adjustment 4/7
3 Move
Movethe
thesafety
safetylock
locklever
leverdownward.
downward.
To Hydraulic Schematic Back Front page Next
2: Feed backward relief pressure adjustment 5/7
4 Move
Movethe
thefeed
feedlever
leverto
tothe
theposition
positionReverse
ReverseFeed.
Feed.
For each pressure adjustment, set the engine rotation speed in the rated speed shown below:
HCR1200: 2500rpm
HCR1500: 2200rpm
To Hydraulic Schematic Back Front page Next
2: Feed backward relief pressure adjustment 6/7
5 Adjust the feed backward relief valve
Clockwise: pressure increase
Counterclockwise: pressure decrease
Setting pressure: 21MPa 6 View from
Adjust the adjuster machine
rear
To Hydraulic Schematic Back Front page Next
2: Feed backward relief pressure adjustment 7/7
7 Be sure to connect the hose back !
Backward side
Forward side
Feed motor
To Hydraulic Schematic Back Front page Next
3: Normal Rotation Relief
Pressure Adjustment
3: Normal rotation relief pressure adjustment 1/5
1 Plug the hose on the normal rotation side
Reverse rotation side
Normal rotation side
Drifter
To Hydraulic Schematic Back Front page Next
3: Normal rotation relief pressure
adjustment 2/5
2 Install the pressure gauge to the P2 pressure port.
Required pressure gauge: 35MPa
To Hydraulic Schematic Back Front page Next
3: Normal rotation relief pressure adjustment 3/5
3 Press the normal rotation switch once
Click! For each pressure adjustment, set the engine rotation
speed in the rated speed shown below:
HCR1200: 2500rpm
HCR1500: 2200rpm
To Hydraulic Schematic Back Front page Next
3: Normal rotation relief pressure adjustment 4/5
4 Adjust the normal rotation relief valve
Clockwise: Pressure increase
Setting pressure: 14MPa Counterclockwise: Pressure decrease
5
Adjust the adjuster View from machine front
To Hydraulic Schematic Back Front page Next
3: Normal rotation relief pressure adjustment 5/5
6 Be sure to connect the hose back!
Reverse rotation side
Normal rotation side
Drifter
To Hydraulic Schematic Back Front page Next
4: Reverse Rotation Relief Pressure
Adjustment
4: Reverse rotation relief pressure adjustment 1/5
1 Plug the hose on the reverse rotation side
Reverse rotation side
Normal rotation
side
Drifter
To Hydraulic Schematic Back Front page Next
4: Reverse rotation relief pressure adjustment 2/5
2 Install the pressure gauge to the P2 pressure port.
Required pressure gauge: 35MPa
To Hydraulic Schematic Back Front page Next
4: Reverse rotation relief pressure adjustment 3/5
3 Keep the reverse rotation switch pressing
Click!
For each pressure adjustment, set the engine rotation
speed in the rated speed shown below:
HCR1200: 2500rpm
HCR1500: 2200rpm
To Hydraulic Schematic Back Front page Next
4: Reverse rotation relief pressure adjustment 4/5
4 Adjust the reverse rotation relief valve
Clockwise: Pressure increase
Setting pressure: 19MPa Counterclockwise: Pressure decrease
5
Adjust the adjuster View from machine rear
To Hydraulic Schematic Back Front page Next
4: Reverse rotation relief pressure adjustment
5/5
6 Be sure to connect the hose back!
Reverse rotation side
Normal rotation
side
Drifter
To Hydraulic Schematic Back Front page Next
5: Boom Relief Pressure Adjustment
5: Boom relief pressure adjustment 1/4
Caution for Adjustment
Check these machine functions prior to adjusting the boom relief pressure.
1. Be sure the rod changer manual switch is OFF.
2. Be sure the rod changer is NOT in the Swing IN position.
Rod changer manual operation switch Rod changer swing IN condition
To Hydraulic Schematic Back Front page Next
5: Boom relief pressure adjustment 2/4
1 Install the pressure gauge to the P1 pressure port.
Required pressure gauge: 35MPa
To Hydraulic Schematic Back Front page Next
5: Boom relief pressure adjustment 3/4
Guide slide backward switch
2 Turn on the guide slide backward switch,
Turn on the guide slide backward switch,
and
andmove
movethe
thecylinder
cylinderto
tostroke
strokeend.
end.
Guide slide rear end
For each pressure adjustment, set the engine rotation
speed in the rated speed shown below:
HCR1200: 2500rpm
HCR1500: 2200rpm
To Hydraulic Schematic Back Front page Next
5: Boom relief pressure adjustment 4/4
3 Adjust the boom relief valve
Clockwise: pressure increase
Setting pressure: 21MPa Counterclockwise: pressure decrease
4
Adjust the adjuster View from machine front
To Hydraulic Schematic Back Front page Next
6: Rotation in H mode Relief
Pressure Adjustment
6: Rotation in H mode relief pressure adjustment 1/7
Caution for Adjustment
Check these machine functions prior to adjusting the rotation in H-mode relief
pressure.
1. Be sure the rod changer manual switch is OFF.
2. Be sure the rod changer is NOT in the Swing IN position.
Rod changer manual operation switch Rod changer swing IN condition
To Hydraulic Schematic Back Front page Next
6: Rotation in H mode relief pressure adjustment 2/7
1 Plug the RFH hose for the rotation modular valve.
Rotation modular
To Hydraulic Schematic Back Front page Next
6: Rotation in H mode relief pressure adjustment 3/7
2 Install the pressure gauge to the P1 pressure port.
Required pressure gauge: 35MPa
To Hydraulic Schematic Back Front page Next
6: Rotation in H mode relief pressure adjustment 4/7
3 Press the normal rotation switch once
Click! For each pressure adjustment, set the engine rotation
speed in the rated speed shown below:
HCR1200: 2500rpm
HCR1500: 2200rpm
To Hydraulic Schematic Back Front page Next
6: Rotation in H mode relief pressure adjustment 5/7
4 Turn on the H mode switch
To Hydraulic Schematic Back Front page Next
6: Rotation in H mode relief pressure adjustment 6/7
5 Adjust the H mode relief valve
Clockwise: pressure increase
Counterclockwise: pressure decrease
Setting pressure:15MPa
6 View from machine
Adjust the adjuster rear
To Hydraulic Schematic Back Front page Next
6: Rotation in H mode relief pressure adjustment 7/7
7 Be sure to connect the hose back!
Rotation modular valve
To Hydraulic Schematic Back Front page Next
