Conic Sections
Conic Sections
Conic Sections
OBSERVE
ILLUSTRATIONS
GIVEN BELOW..
Ellipse
Section Plane
ola
Section Plane
Through Generators Hyperbola
rab
Pa Parallel to Axis.
3 3
2 2
1
1
A 1 2 3 4 3 2 1 B
C
PROBLEM 4. ELLIPSE
MAJOR AXIS AB & MINOR AXIS CD ARE
BY ARCS OF CIRCLE METHOD
100 AMD 70MM LONG RESPECTIVELY
.DRAW ELLIPSE BY ARCS OF CIRLES
METHOD. As per the definition Ellipse is locus of point P moving in
a plane such that the SUM of it’s distances from two fixed
STEPS: points (F1 & F2) remains constant and equals to the length
1.Draw both axes as usual.Name the of major axis AB.(Note A .1+ B .1=A . 2 + B. 2 = AB)
ends & intersecting point
2.Taking AO distance I.e.half major
axis, from C, mark F1 & F2 On AB . p4 C
( focus 1 and 2.) p3
3.On line F1- O taking any distance, p2
mark points 1,2,3, & 4 p1
4.Taking F1 center, with distance A-1
draw an arc above AB and taking F2
center, with B-1 distance cut this arc.
Name the point p1 A B
O
5.Repeat this step with same centers but F1 1 2 3 4 F2
taking now A-2 & B-2 distances for
drawing arcs. Name the point p2
6.Similarly get all other P points.
With same steps positions of P can be
located below AB.
7.Join all points by smooth curve to get
an ellipse/ D
PROBLEM 5. ELLIPSE
DRAW RHOMBUS OF 100 MM & 70 MM LONG BY RHOMBUS METHOD
DIAGONALS AND INSCRIBE AN ELLIPSE IN IT.
STEPS: 2
1. Draw rhombus of given
dimensions.
2. Mark mid points of all sides &
name Those A,B,C,& D
3. Join these points to the ends of A B
smaller diagonals.
4. Mark points 1,2,3,4 as four
centers.
5. Taking 1 as center and 1-A 3 4
radius draw an arc AB.
6. Take 2 as center draw an arc CD.
7. Similarly taking 3 & 4 as centers
and 3-D radius draw arcs DA & BC.
D C
1
PROBLEM 6:- POINT F IS 50 MM FROM A LINE AB.A POINT P IS MOVING IN A PLANE ELLIPSE
SUCH THAT THE RATIO OF IT’S DISTANCES FROM F AND LINE AB REMAINS CONSTANT
AND EQUALS TO 2/3 DRAW LOCUS OF POINT P. { ECCENTRICITY = 2/3 } DIRECTRIX-FOCUS METHOD
ELLIPSE
A
STEPS:
1 .Draw a vertical line AB and point F
DIRECTRIX
50 mm from it.
2 .Divide 50 mm distance in 5 parts. 45mm
3 .Name 2nd part from F as V. It is 20mm
and 30mm from F and AB line resp.
3 0 mm
It is first point giving ratio of it’s
distances from F and AB 2/3 i.e 20/30
4 Form more points giving same ratio such
as 30/45, 40/60, 50/75 etc. (vertex) V
5.Taking 45,60 and 75mm distances from F ( focus)
line AB, draw three vertical lines to the
right side of it.
6. Now with 30, 40 and 50mm distances in
compass cut these lines above and below,
with F as center.
7. Join these points through V in smooth
curve.
This is required locus of P.It is an ELLIPSE.
B
PROBLEM 7: A BALL THROWN IN AIR ATTAINS 100 M HIEGHT
PARABOLA
AND COVERS HORIZONTAL DISTANCE 150 M ON GROUND. RECTANGLE METHOD
Draw the path of the ball (projectile)-
STEPS: 6 6
1.Draw rectangle of above size and
divide it in two equal vertical parts
2.Consider left part for construction. 5 5
Divide height and length in equal
number of parts and name those
1,2,3,4,5& 6 4 4
3.Join vertical 1,2,3,4,5 & 6 to the
top center of rectangle
4.Similarly draw upward vertical
3 3
lines from horizontal1,2,3,4,5
And wherever these lines intersect
previously drawn inclined lines in
sequence Mark those points and 2 2
further join in smooth possible curve.
5.Repeat the construction on right side
rectangle also.Join all in sequence. 1 1
This locus is Parabola.
.
1 2 3 4 5 6 5 4 3 2 1
Problem no.8: Draw an isosceles triangle of 100 mm long base and PARABOLA
110 mm long altitude.Inscribe a parabola in it by method of tangents. METHOD OF TANGENTS
Solution Steps: C
1. Construct triangle as per the given 14
dimensions. 1
2. Divide it’s both sides in to same no.of 13
2
equal parts. 12
3
3. Name the parts in ascending and 11
descending manner, as shown. 4
10
4. Join 1-1, 2-2,3-3 and so on. 5
5. Draw the curve as shown i.e.tangent to 9
6
all these lines. The above all lines being 8
tangents to the curve, it is called method 7
of tangents. 7 8
6
9
5 10
4 11
3 12
2 13
1
14
A B
PROBLEM 9: Point F is 50 mm from a vertical straight line AB. PARABOLA
Draw locus of point P, moving in a plane such that DIRECTRIX-FOCUS METHOD
it always remains equidistant from point F and line AB.
PARABOLA
SOLUTION STEPS:
1.Locate center of line, perpendicular to A
AB from point F. This will be initial
point P and also the vertex.
2.Mark 5 mm distance to its right side,
name those points 1,2,3,4 and from P1
those
draw lines parallel to AB.
3.Mark 5 mm distance to its left of P and (VERTEX) V
name it 1. F
O 1 2 3 4
4.Take O-1 distance as radius and F as
center draw an arc ( focus)
cutting first parallel line to AB. Name
upper point P1 and lower point P2.
P2
(FP1=O1)
P V = C 9
+++ +++ +
10 1 = 10
5 2 = 10 8
4 2.5 = 10
2.5 4 = 10 7
2 5 = 10
1 10 = 10 6
PRESSURE
Now draw a Graph of 5
( Kg/cm2)
Pressure against Volume.
It is a PV Diagram and it is Hyperbola.
Take pressure on vertical axis and
4
Volume on horizontal axis.
3
2
1
0 1 2 3 4 5 6 7 8 9 10
VOLUME:( M3 )
PROBLEM 12:- POINT F IS 50 MM FROM A LINE AB.A POINT P IS MOVING IN A PLANE HYPERBOLA
SUCH THAT THE RATIO OF IT’S DISTANCES FROM F AND LINE AB REMAINS CONSTANT
AND EQUALS TO 2/3 DRAW LOCUS OF POINT P. { ECCENTRICITY = 2/3 }
DIRECTRIX
FOCUS METHOD
STEPS: A
1 .Draw a vertical line AB and point F
50 mm from it.
2 .Divide 50 mm distance in 5 parts. 30mm
3 .Name 2nd part from F as V. It is 20mm
and 30mm from F and AB line resp.
45m
It is first point giving ratio of it’s
m
distances from F and AB 2/3 i.e 20/30
4 Form more points giving same ratio such
as 30/45, 40/60, 50/75 etc. (vertex)
V
F ( focus)
5.Taking 45,60 and 75mm distances from
line AB, draw three vertical lines to the
right side of it.
6. Now with 30, 40 and 50mm distances in
compass cut these lines above and below,
with F as center.
7. Join these points through V in smooth
curve.
This is required locus of P.It is an ELLIPSE.
B
ELLIPSE
Problem 13:
TANGENT & NORMAL
TO DRAW TANGENT & NORMAL
TO THE CURVE FROM A GIVEN POINT ( Q )
1. JOIN POINT Q TO F1 & F2
2. BISECT ANGLE F1Q F2 THE ANGLE BISECTOR IS NORMAL
3. A PERPENDICULAR LINE DRAWN TO IT IS TANGENT TO THE CURVE.
p4 C
p3
p2
p1
A B
O
F1 1 2 3 4 F2
L
MA
NOR
Q TAN
GE
NT
D
ELLIPSE
Problem 14:
TANGENT & NORMAL
TO DRAW TANGENT & NORMAL
TO THE CURVE
ELLIPSE
FROM A GIVEN POINT ( Q ) A
DIRECTRIX
1.JOIN POINT Q TO F. T
2.CONSTRUCT 900 ANGLE WITH
THIS LINE AT POINT F
3.EXTEND THE LINE TO MEET DIRECTRIX
AT T
4. JOIN THIS POINT TO Q AND EXTEND. THIS IS
TANGENT TO ELLIPSE FROM Q (vertex) V
5.TO THIS TANGENT DRAW PERPENDICULAR F ( focus)
LINE FROM Q. IT IS NORMAL TO CURVE. 900
N
Q
N
T
PARABOLA
Problem 15: TANGENT & NORMAL
TO DRAW TANGENT & NORMAL
TO THE CURVE T PARABOLA
FROM A GIVEN POINT ( Q )
A
1.JOIN POINT Q TO F.
2.CONSTRUCT 900 ANGLE WITH
THIS LINE AT POINT F
3.EXTEND THE LINE TO MEET DIRECTRIX
AT T
4. JOIN THIS POINT TO Q AND EXTEND. THIS IS VERTEX V
TANGENT TO THE CURVE FROM Q 900
F
5.TO THIS TANGENT DRAW PERPENDICULAR ( focus)
LINE FROM Q. IT IS NORMAL TO CURVE.
N
Q
B N
T
HYPERBOLA
Problem 16
TANGENT & NORMAL
TO DRAW TANGENT & NORMAL
TO THE CURVE
FROM A GIVEN POINT ( Q ) A
1.JOIN POINT Q TO F.
2.CONSTRUCT 900 ANGLE WITH THIS LINE AT
POINT F T
3.EXTEND THE LINE TO MEET DIRECTRIX AT T
4. JOIN THIS POINT TO Q AND EXTEND. THIS IS
TANGENT TO CURVE FROM Q
(vertex)
V
F ( focus)
5.TO THIS TANGENT DRAW PERPENDICULAR 900
LINE FROM Q. IT IS NORMAL TO CURVE.
N
N Q
T
ENGINEERING CURVES
Part-II
(Point undergoing two types of displacements)