Scribd
Upload
181 views11 pages

Cell Phone Operated Robot

1. The document discusses a DTMF-controlled robot that is operated using a mobile phone. 2. DTMF technology uses dual tones sent over analog phone lines to signal buttons pressed on the phone. This allows the robot to be controlled remotely from another phone. 3. The robot receives DTMF tones corresponding to buttons pressed on the controlling phone and uses these tones to operate motors and move in different directions.

Uploaded by

Dheeksha Maturi
Copyright
© Attribution Non-Commercial (BY-NC)
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PPTX, PDF, TXT or read online on Scribd
181 views11 pages

Cell Phone Operated Robot

1. The document discusses a DTMF-controlled robot that is operated using a mobile phone. 2. DTMF technology uses dual tones sent over analog phone lines to signal buttons pressed on the phone. This allows the robot to be controlled remotely from another phone. 3. The robot receives DTMF tones corresponding to buttons pressed on the controlling phone and uses these tones to operate motors and move in different directions.

Uploaded by

Dheeksha Maturi
Copyright
© Attribution Non-Commercial (BY-NC)
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PPTX, PDF, TXT or read online on Scribd
You are on page 1/ 11

By - 1. K. Ravi kumar(08331A0465) 2. B. Sankara Narayana(08331A0418) 3. M. Deeksha(08331A0467) 4. B.

Rama rao(08331A0420)

Under the esteemed guidance of Smt. M. Lakshmi Prasanna Rani, Asst. Professor of Dept of ECE, MVGRCOE

INTRODUCTION DTMF TECHNOLOGY DTMF KEYPAD PROJECT OVERVIEW BLOCK DIAGRAM APPLICATIONS

Radio control is the use of radio signals to remotely control a device. Industrial, military, and scientific research organizations make use of radio-controlled vehicles as well.

A remote control vehicle is defined as any mobile device .


Conventionally, wireless-controlled robots use RF circuits, which have the drawbacks of limited working range, limited frequency range and limited control. Use of a mobile phone for robotic control can overcome these limitations.

Dual-Tone Multi-Frequency (DTMF)

Dual-tone multi-frequency (DTMF) signalling is used for telecommunication signaling over analog telephone lines in the voice-frequency band between telephone handsets and other communications devices and the switching center. The version of DTMF used for telephone tone dialing is known by the trademarked term Touch-Tone

DTMF TELEPHONE KEYPAD

The contemporary keypad is laid out in a 4x3 grid. When used to dial a telephone number, pressing a single key will produce a pitch consisting of two simultaneous pure tone sinusoidal frequencies. The row in which the key appears determines the low frequency, and the column determines the high frequency..

DTMF Telephone Keypad

The robot is controlled by a mobile phone that makes a call to the mobile phone attached to the robot.

In the course of a call, if any button is pressed, a tone corresponding to the button pressed is heard at the other end of the call.
This tone is called dual-tone multiple-frequency (DTMF) tone

DTMF signalling is used for telephone signaling over the line in the voice-frequency band to the call switching centre.

The version of DTMF used for telephone tone dialing is known as Touch-Tone.

This is wireless controller robot hence the limitation of wired robots is completely overcome by using latest technology of mobile phones.

In this project we use RF circuitry to enhance the limitation of a controlled range, no more, a constraint of this model.
Limitless area coverage is the main advantage of this land rover.

This land rover has only one disadvantage that is it can be operated in area where mobile network is available and if mobile network is not available it can not be operated.

This land rover can carry any thing mounted on top it This can be fitted in an attractive form of a toy robot It can also be used to make mobile bomb by making some modification. If we use the switching IC instead of the driver IC we can turn on and off any appliances connected to this robot

You might also like