Scribd Logo
Upload

Welcome to Scribd!

  • 11 views

    Maintenance Training For Speed Dome

    Uploaded by

    jlgonzales
    ptz mantenimiento

    Copyright:

    © All Rights Reserved
    Download as PPT, PDF, TXT or read online from Scribd

    Maintenance Training For Speed Dome

    Uploaded by

    jlgonzales
    11 views26 pages
    ptz mantenimiento

    Original Title

    Maintenance training for Speed Dome

    Copyright

    © © All Rights Reserved

    Available Formats

    PPT, PDF, TXT or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    ptz mantenimiento

    Copyright:

    © All Rights Reserved
    Download as PPT, PDF, TXT or read online from Scribd
    Download as ppt, pdf, or txt
    11 views26 pages

    Maintenance Training For Speed Dome

    Uploaded by

    jlgonzales
    ptz mantenimiento

    Copyright:

    © All Rights Reserved
    Download as PPT, PDF, TXT or read online from Scribd
    Download as ppt, pdf, or txt
    of 26

    Front-end Product Training Program –

    Speed Dome
    Table of Contents

    Speed dome classification


    Speed dome basic information
    FAQ
    Upgrade
    Speed dome Classification
    Speed Dome
    Components
    • Camera
    • High speed PTZ
    • Decoder
    • Dome enclosure
    • Fan
    • Heater
    Speed Dome Components

    Address,
    protocol dial
    switch button

    Main chip

    Main control board


    Speed Dome Components

    Power
    socket
    User port

    Alarm Port

    Switch board

    Power board
    Speed Dome Components
    Encode chip
    Network
    part

    Connect to the
    switch board
    Flash chip

    Davinci
    Speed Dome Layout
    FAQ
    • After the rectify, the AC24V from the on-off voltage of U1
    （ UCC3809 ） becomes the DC+12V ， among which ,
    the U2 （ TLP281-1 ）、 U3 （ TLV431 ） is the key chi
    p of the voltage auto control.
    • +12V from U4 （ L7805 ） to VCC （ +5V ）， VCC fro
    m U5 （ 76381-3.3V ） to +3.3V.
    • U8 （ LM3S608 ） alarm control chip. Please bu
    rn the boot application and then upgrade the ap
    plication via the COM. The speed dome RS485
    connects to the RS232 of the PC is via the AMP
    socket and the U3 (184 chip) of the main board.
    FAQ

    •The alarm output control is from the 19/20-pi


    n of the U8(LM3S608) to control the dynatron Q5/Q
    4, and then send to the JK1,JK3 of the U10 （ ULN20
    03 ） reverse relay. In normal status, the relay 4/13
    and 6/11 is close. Then 4/13 and 8/9 are open. The sh
    ort circuit cap of jump J13/J14 is in the 2/3/-pin.
    FAQ

    +12V becomes +7V via U5 （ MP1411 ）， a


    nd then becomes VCC via （ L7805 ） VCC ，
    then becomes +3.3V via U14 （ AMC1117-3.3
    V ）， then +3.3V becomes +3.3VA via L5 ， +
    12V becomes +12VA and +12VA1 via L7 and L4
    to go to the stepper. The reset is done by the U2
    （ ASM705 ） chip.
    FAQ

    The horizontal position uses the new component ： Hall compo


    nents -A1104-(SIP-3) ， it uses the electromagnetic induction to te
    st the horizontal test. The tilt stop is to slightly touch the on-off butto
    n (External, from J4 ).
    Stepper control ： U11 （ LPC2365 ） needs to burn the applic
    ation. The control application will be sent to the chip U9, U12 （ L6
    219DSA ） to drive the stepper via the U10 （ TLC7225C ） 4-ch
    annel D/A switch.
    FAQ

    U7 （ MAX7456 ） is OSD chip ， VCC is to provide the power ， clock


    X3 （ 27MH ）， the 8 to 11–pin is to communicate with the ARM ， 22-
    pin is for the video input, 26-pin is for the video output,U13 （ OPA690) i
    s for video output.
    The application can embed the OSD to video signal.
    You can check the U7 working status if the OSD is abnormal.
    FAQ
    • There is no respond after turn on the device.
    Please make sure there is no short circuit. Test +12V, VCC （ +5V ） , +3.3V is O
    K or note. If there is a problem please fix the power board. Finally check the AMP co
    nnection is OK or not.
    FAQ

    On-off button
    FAQ
    The 485 signal is from the user port J9 （ power board ） to
    the main board for the U3 （ LBC184 ）， and then to the U1
    1 （ LPC2365 ） . LED1 is the RS485 indicator light.
    The problem may be ：
    1 Can not upgrade the application.
    2 Can not control the PTZ or can not go to the menu.
    The reason may be ：
    1 Address, protocol setup problem
    2 U3 （ LBC184 ） working improperly or is malfunction
    3 AMP connection problem
    FAQ

    184 is communication port


    FAQ

    1 、 Main board is no power: AMP or the electronic br


    ush is abnormal.
    2 、 Can not control the PTZ: U3 （ LBC184 ） chip is
    abnormal.Address, protocol or baud rate setup is erro
    r.
    3 、 No character or abnormal: application is wrong, o
    r U7 （ MAX7456 ） working is improper or malfunctio
    n.
    FAQ
    Davinci main board ：
    The video signal will be sent to the main chip （ U7 TMS320) to
    compress via the video A/D(U21 5150 ） chip. Then from the network
    card chip （ U5 RTL8201 ） to our PC.
    Network problem. Please make sure the Davinci board has booted up.
    Please check the voltage and the clock if it does not boot up properly. If
    it has booted up properly ,please change the application.
    If there is a network problem when the board properly booted up,
    please check the IP address is OK or not. Please check the
    RTL8201(U5) if the IP is OK. Otherwise change the IP address (Please
    refer to the following information.)
    FAQ
    How to change the IP when the network is error.
    You can change via the COM.
    Press the * when the device boots up.
    U-Boot 1.1.4 for DAHUA Davinci ;Version 3.0; modify by Sword;20071212 (Jan 13 2009 - 15:10:14)

    U-Boot code: 81080000 -> 81099694 BSS: -> 810B2E68


    RAM Configuration:
    Bank #0: 80000000 64 MB
    Flash Manufacturer=AMD
    flash reset;add by SwordFlash: 16 MB
    In: serial
    Out: serial
    Err: serial
    ARM Clock :- 256MHz
    DDR Clock :- 162MHz
    CPU:DM6446
    nARM Clock :- 297MHz
    Loading ............DHBOOT# *****

    Unknown command '*****' - try 'help'


    DHBOOT#
    FAQ

    “DHBOOT#” input command here.


    “setenv dh_keyboard 0
    setenv appauto 0
    save”

    Reboot and then input “netinit IP address subnet mask default


    gateway ” after you see #, input ii and click the return button. Please
    reboot and then input the following information.

    “setenv dh_keyboard 1
    setenv appauto 1
    save”
    Upgrade Tool

    USB Connection Cable Download Tool

    Power board application download cable


    Upgrade Tool

    Download Tool (LPT) Download Tool Switch Cable

    Main board download cable


    Upgrade Tool
    LM3S608 alarm output chip in the power board is to burn the applications. Please use
    the tool power board application download cable to burn the Boot application. And the
    n use the 232 to 485 tool to burn the main applications. There is no alarm if there is n
    o main applications.
    LPC2365 on the main control board is the key control chip. The Boot application can u
    se the tool or the on-line download tool to burn. The on-line burn is to use the main bo
    ard download cable to burn the Boot application and then uses the 232 to 485 switche
    r to burn the main applications via the RS485. You can not control the PTZ if there is
    no application in the LPC2365.
    For the Davinci board, you can use the burner to burn the Boot application to the Flas
    h and then jointing to the board to upgrade via the TFTP. You can not see the network
    video if there is no application.
    Upgrade Tool

    LPC2365 on-
    line burn port

    LM3S608 on-
    line burn port
    Thank you ！

    You might also like