Flip Flops

Lecture 11: Sequential Logic

Latches & Flip-flops
 Introduction
 Memory Elements
 Pulse-Triggered Latch
 S-R Latch
 Gated S-R Latch
 Gated D Latch

 Edge-Triggered Flip-flops
 S-R Flip-flop
 D Flip-flop
 J-K Flip-flop
 T Flip-flop
 Asynchronous Inputs
Lecture 11: Sequential Logic: Latches 2
& Flip-flops
Introduction
 There are two types of sequential circuits:
 synchronous: outputs change only at specific time
 asynchronous: outputs change at any time

 Multivibrator: a class of sequential circuits. They

can be:
 bistable (2 stable states)
 monostable or one-shot (1 stable state)
 astable (no stable state)

 Bistable logic devices: latches and flip-flops.

 Latches and flip-flops differ in the method used for
changing their state.

Introduction 3
Memory Elements
 Memory element: a device which can remember
value indefinitely, or change value on command
from its inputs.

Memory Q
command element stored value

 Characteristic table:
Command Q(t) Q(t+1)
(at time t) Q(t): current state
Set X 1
Q(t+1) or Q+: next state
Reset X 0
Memorise / 0 0
No Change 1 1

Memory Elements 4
Memory Elements
 Memory element with clock. Flip-flops are memory
elements that change state on clock signals.

Memory Q
command element stored value

clock

 Clock is usually a square wave.

Positive pulses

Positive edges Negative edges

Memory Elements 5
Memory Elements
 Two types of triggering/activation:
 pulse-triggered
 edge-triggered

 Pulse-triggered
 latches
 ON = 1, OFF = 0

 Edge-triggered
 flip-flops
 positive edge-triggered (ON = from 0 to 1; OFF = other
time)
 negative edge-triggered (ON = from 1 to 0; OFF = other
time)

Memory Elements 6
S-R Latch
 Complementary outputs: Q and Q'.
 When Q is HIGH, the latch is in SET state.
 When Q is LOW, the latch is in RESET state.
 For active-HIGH input S-R latch (also known as NOR
gate latch),
R=HIGH (and S=LOW)  RESET state
S=HIGH (and R=LOW)  SET state
both inputs LOW  no change
both inputs HIGH  Q and Q' both LOW (invalid)!

S-R Latch 7
S-R Latch
 Characteristics table for active-high input S-R latch:
S R Q Q'
0 0 NC NC No change. Latch
remained in present state. S Q
1 0 1 0 Latch SET.
0 1 0 1 Latch RESET. R Q'
1 1 0 0 Invalid condition.

S-R Latch 8
S-R Latch
 Active-HIGH input S-R latch
10 100 R S R Q Q'
Q 11000 1 0 1 0 initial
0 0 1 0 (afer S=1, R=0)
0 1 0 1
Q' 0 0 1 1 0 0 0 0 1 (after S=0, R=1)
10 001 S
1 1 0 0 invalid!

S-R Latch 9
Gated D Latch
 Make R input equal to S'  gated D latch.
 D latch eliminates the undesirable condition of invalid
state in the S-R latch.

D
Q D Q
EN EN
Q' Q'

Gated D Latch 10
Gated D Latch
 When EN is HIGH,
 D=HIGH  latch is SET
 D=LOW  latch is RESET

 Hence when EN is HIGH, Q ‘follows’ the D (data)

input.
 Characteristic table:
EN D Q(t+1)
1 0 0 Reset
1 1 1 Set
0 X Q(t) No change

When EN=1, Q(t+1) = D

Gated D Latch 11
Latch Circuits: Not Suitable
 Latch circuits are not suitable in synchronous logic
circuits.
 When the enable signal is active, the excitation
inputs are gated directly to the output Q. Thus, any
change in the excitation input immediately causes a
change in the latch output.
 The problem is solved by using a special timing
control signal called a clock to restrict the times at
which the states of the memory elements may
change.
 This leads us to the edge-triggered memory
elements called flip-flops.

Gated D Latch 12
Edge-Triggered Flip-flops
 Flip-flops: synchronous bistable devices
 Output changes state at a specified point on a
triggering input called the clock.
 Change state either at the positive edge (rising edge)
or at the negative edge (falling edge) of the clock
signal.

Clock signal

Positive edges Negative edges

Edge-Triggered Flip-flops 13
Edge-Triggered Flip-flops
 S-R, D and J-K edge-triggered flip-flops. Note the “>”
symbol at the clock input.

S Q D Q J Q
C C C
R Q' Q' K Q'

Positive edge-triggered flip-flops

S Q D Q J Q
C C C
R Q' Q' K Q'

Negative edge-triggered flip-flops

Edge-Triggered Flip-flops 14
S-R Flip-flop
 S-R flip-flop: on the triggering edge of the clock pulse,
 S=HIGH (and R=LOW)  SET state
 R=HIGH (and S=LOW)  RESET state
 both inputs LOW  no change
 both inputs HIGH  invalid
 Characteristic table of positive edge-triggered S-R flip-
flop:
S R CLK Q(t+1) Comments
0 0 X Q(t) No change
0 1  0 Reset
1 0  1 Set
1 1  ? Invalid

X = irrelevant (“don’t care”)

 = clock transition LOW to HIGH

SR Flip-flop 15
S-R Flip-flop
 It comprises 3 parts:
 a basic NAND latch
 a pulse-steering circuit
 a pulse transition detector (or edge detector) circuit

 The pulse transition detector detects a rising (or

falling) edge and produces a very short-duration
spike.

SR Flip-flop 16
S-R Flip-flop
The pulse transition detector.
S
Q
Pulse
CLK transition
detector
Q'
R

CLK' CLK'
CLK CLK* CLK CLK*

CLK CLK

CLK' CLK'

CLK* CLK*

Positive-going transition Negative-going transition

(rising edge) (falling edge)
SR Flip-flop 17
D Flip-flop
 D flip-flop: single input D (data)
 D=HIGH  SET state
 D=LOW  RESET state

 Q follows D at the clock edge.

 Convert S-R flip-flop into a D flip-flop: add an inverter.
D S D CLK Q(t+1) Comments
Q
1  1 Set
CLK C
0  0 Reset
R Q'
 = clock transition LOW to HIGH
A positive edge-triggered D flip-
flop formed with an S-R flip-flop.

D Flip-flop 18
J-K Flip-flop
 J-K flip-flop: Q and Q' are fed back to the pulse-
steering NAND gates.
 No invalid state.
 Include a toggle state.
 J=HIGH (and K=LOW)  SET state
 K=HIGH (and J=LOW)  RESET state
 both inputs LOW  no change
 both inputs HIGH  toggle

J-K Flip-Ffop 19
J-K Flip-flop
 J-K flip-flop.
J
Q
Pulse
CLK transition
detector
Q'
K

 Characteristic table. Q J K Q(t+1)

J K CLK Q(t+1) Comments 0 0 0 0
0 0  Q(t) No change 0 0 1 0
0 1  0 Reset 0 1 0 1
1 0  1 Set 0 1 1 1
1 1  Q(t)' Toggle 1 0 0 1
1 0 1 0
1 1 0 1
Q(t+1) = J.Q' + K'.Q
1 1 1 0

J-K Flip-flop 20
T Flip-flop
 T flip-flop: single-input version of the J-K flip flop,
formed by tying both inputs together.
T
Q T J
Pulse Q
CLK transition CLK C
detector
Q' K Q'

 Characteristic table.
T CLK Q(t+1) Comments Q T Q(t+1)
0  Q(t) No change 0 0 0
1  Q(t)' Toggle 0 1 1
1 0 1
1 1 0
Q(t+1) = T.Q' + T'.Q

T Flip-flop 21
Conversion of FLIP FLOPS
Steps To Convert from One Flip Flop to Other :
Let there be required flip flop to be constructed using sub-flip flop:
Draw the truth table of the required flip-flop.

Write the corresponding outputs of sub-flip flop to be used from

the excitation table.

Draw K-Maps using required flip flop inputs and obtain excitation

functions for sub-flip flop inputs.

Construct a logic diagram according to the functions obtained .
S = JQ’

R = KQ
S = JQ’

R = KQ
Convert SR To D Flip Flop:

Excitation Functions: S = D, R = D‘
Applications of Flip-Flops:
These are the various types of flip-flops being used in digital electronic circuits and the
applications of Flip-flops are as specified below.
Counters Frequency Dividers Shift Registers Storage Registers
Bounce elimination switch Data storage Data transfer
Latch Registers Memory