Stitch & Seam

Prepared by,
 LATIKA TEXTILE AND GARMENT CONSULTANCY
 Stitch

Stitch:
British standard 3870, defines stitch as: One units of conformation
resulting from one or more strands or loops of thread intralooping,
Interlooping or passing into or through the fabric or material.

Inter looping : Loop of one thread passes through the loop of another thread.

Intra looping : Loop of one thread passes through the loop of same thread.

Inter Lacing: One thread passes over another thread.

stitch
 Stitch
 Stitch classification is based on:
 Structure of the stitch
 Method of interlacing stitch properties.

 Stitch properties:
 Relate to aesthetics and performance
 Stitch size

 Stitch length, width, and depth.

 Thread tension
 Stitch consistency.
 Classification of stitches:-
 Stitch classification is based on:
 Structure of the stitch
 Method of interlacing stitch properties.
Types of stitches:-
1. Stitch Class- 100 (Single thread chain stitch).
2. Stitch Class- 200 (Hand Stitch).
3. Stitch Class- 300 (Lock Stitch).
4. Stitch Class- 400 (Multi thread chain stitch).

5. Stitch Class- 500 (Over lock stitch).

6. Stitch Class- 600 (Covering chain stitch).

 Stitch and Classification

Class 100:(Single thread chain stitch):

is chain stitch type, is formed with one or more needle threads introduced
from one side of the material only.
 chain stitch is elastic and thicker than lockstitch and can easily be
raveled;
 particular care is required to prevent runback from the last stitch.
 Used for temporary stitching or for Blind stitching.
 Stitch and Classification
Class 200:
is a hand stitch type, is formed by single thread passed from one side of the
material to the other in successive needle penetrations.
 a slow process and need huge manpower to finish bulk order.
 Used for handwork.

Sub-Classes:
Sub-Class-202: This type of stitch is formed by hand.
Sub-Class-209: This type of stitch is formed by “Pique Stitch
Machine’’.

Uses: Lapel of Blazer, collar of shirt, saddle stitch etc.

 Stitch and Classification
Class 300:
is a lock stitch type, is formed by a needle thread or threads, introduced from
one side of the material, interlacing with an under thread
 supplied from a bobbin on the other side.
 low bulk and thin, good strength and abrasion resistance
 Poor elasticity, non ravel
 limited sewing length, need to replace bobbin thread.
 for seams requiring stretch.

Subclass: 301, 304

Usages:
Lock stitch is extensively used for joining fabrics collar, cuff, pocket, facing etc.
Top stitching is used for button holing, attaching, blind stitching etc.
 Stitch and Classification
 Sub-Class-301:

 Use: Top stitching in garments.

 Sub-Class-304:

 Uses: Elastic attaching, lace attaching etc

 Stitch and Classification
 Class 400:
 is multi thread chain stitch type, is formed with two/more groups of threads
having general characteristic of interlacing interloping of the loops of the two
groups.
 non ravel, strong, good elasticity, less likely to cause seam pucker due
to structural jamming
 good seam stretch
 does not need to wind bobbin
 lower resistance to runback and have increased bulk under the seam

 Hemming: Hem is the end of the garment and the process of making hem is
called hemming
 Stitch and Classification
Subclass:

401(1n+1l); Use in Jens.

406(2n+2l); Use in T-Shirt (Heming). (Flat Lock).

407(3n+1l) Use in Brief’s. (Flat Lock).

Usages:
This type of stitches is used for sewing lace, braid and elastic. Stitch
type-401 is used in jeans and trouser.
 Stitch and Classification
401: 1Needle + 1Looper
Uses: Inseam and out seam of jeans.

Upper
side

Bottom
side
406: 2Needle + 1Looper

Uses: Sleeve and bottom hem of T-shirt.

Stitch and Classification
407: 3Needle + 1Looper

Uses: Sleeve and bottom hem of T-shirt & Polo-shirt.

 Stitch and Classification
Class 500:
is over lock over edge stitch type, is formed with one or more needles and/or loopier threads with at least one
thread passing round the edge of the material being sewn.
 Excellent stretchable good recovery
 Seam or edge neatening
 suitable for many types of fabric
 subject to fraying or slippage.
Subclass:
British Standard:
 503(1n+1l); Use for edging.
 504(1n+2l); Use for edging & light seaming.
 514(2n+2l); Use edging & Heavy seaming.

 American Standard: Combination Stitch

 515(401 + 503); Use for edging & sewing.
 516(401 + 504); Use for edging & sewing.

Usages: This stitch type can be used to make a decorative edge.

 Stitch and Classification
Sub-Classes:

503: 1Needle + 1Looper

Use: Only for edging.

504: 1Needle + 2Looper

Uses: For edging & light seaming.

514: 1Needle + 2Looper

Uses: For edging & heavy seaming.

 Stitch and Classification
Class 600:
is formed with two or more groups of threads, has for a general characteristic that two
groups of thread cover surfaces of the material.
 High elasticity, seam neatening and Flat seam stitch, Bulk, Fast
machine speed
 No need of Bobbin
 Greater thread consumption
 Covering stitches for decorative purpose, Can be used to join two raw
edges, suitable for knitted garments.
Subclass:
602; Use for decorative purpose.
605; Use for decorative purpose.

Usages:
This type of stitch is used for sewing under wear for attaching lace, braid elasticity.
 Stitch and Classification
 Sub-Classe-602: 2Needle + 2Looper

 Use: Sleeve and bottom hem of T-shirt, Polo-shirt & decorative purpose.

 Sub-Classe-605: 3Needle + 2Looper

 Uses: For decorative purpose & elastic attaching of under garments.

 Seam
What is Seam?
A seam is a joint of two pieces of fabric in producing a three -dimensional
shape of a garment.

Properties of good seam are,

= Smooth fabric joints

= No Missed or Uneven stitches
= No damage to the material being sewn
= Achievement of strength, elasticity, Durability,
security and comfort
= Comfortable while garment is in use
 Seam and Classification
SEAMS DESIGNATION

Each stitched seam is designed numerically by five digits:

 0.00.00 refers to the CLASS, 1-8;

 0.00.00 refers to the material configuration,

01 to 99;

 0.00.00 refers to needle penetrations, material

configurations, 01-99.
 Seam and Classification

PLAIN SEAM or SUPERIMPOSED SEAM Class 1

•Formed by superimposing the edge of one piece of component over the

other, these seams are produced with a minimum of two pieces of
component.

• Each component is limited on the same end.

Seam and Classification
PLAIN SEAM or SUPERIMPOSED SEAM Class 1
 Seam and Classification

Class 2 Lapped seam or welt seam

* Formed by lapping two pieces of component, they are produced with

minimum of two pieces of component.

* One component is limited on one end and the other is limited on the
other end. The limited edges of these two components are put in opposite
directions.
* Used for: main seaming of denim jackets, jeans, and overalls. Fabrics that
will not ravel, unlined garments, side seams of shirts, joining lace to another
fabric, attaching patch pockets, decorative finish
Seam and Classification
Class 2 Lapped seam or welt seam
 Seam and Classification
Class 3 Bound seam
Constructed by binding the component edge with another narrow
component. The seam produced with minimum of two pieces of component.

One component is limited on one end and the other is limited on both
ends.

Used for : finishing necklines, sleeves hems, inside waistbands of trousers

and pants, finishing seams on unlined jackets and coats, adding interest as a
design or decorative detail, finishing raw edges, continuing the motif design
of lace.
Seam and Classification
Class 3 Bound seam
 Seam and Classification
Class 4 Flat or channel seam

Two pieces of fabric are laid flat with their edges closing each other
without overlapping. Seams are produced with minimum of two pieces of
component.

Both components are limited on one end but they are put opposition to
each other on the same level.
* Used for: close fitting garments where the seam allowance may put
pressure on the body, high-stretch fabrics, athletic apparel, shape wear,
undergarments, thermal underwear, swimwear.
Seam and Classification
Class 4 Flat or channel seam
 Seam and Classification

Class 5 Ornamental Seam

A seam class for decorative sewing on garments.

Seams are produced with minimum of one piece of component, with

unlimited edges on both ends.

* Used for: adding a design detail, cording, piping, tucking, welting,
decorative stitching
Seam and Classification
Class 5 Ornamental Seam
 Seam and Classification
Class 6 Turned hem or Edge neatening

Stitching work made on the fabric edges for neatening.

Seams are produced with one piece of component. This seam has one
limited edge on one end.
Seam and Classification
Class 6 Turned hem or Edge neatening
 Seam and Classification
Class 7 Edge Stitched Seam

A narrow piece is sewn to the edge of a garment part.

Seams are produced with minimum of two pieces of component. One

component is limited on one end, and the other narrow one is limited on
both ends.
Seam and Classification
Class 7 Edge Stitched Seam
 Seam and Classification
Class 8 Enclosed Seam

Only one piece of component involved in construction the seam, stitches are
applied on its edge/s.

Seams are produced with minimum of one piece of component with a limited
edge on two ends.
Seam and Classification
Class 8 Enclosed Seam
 Seam Problems
 SEAM PROBLEMS

• Seam Pucker
• Grinning
• Skipped Stitches
• Broken Needle Threads
• Broken Bobbin Threads
• Needle Damage on Fabric
• Seam Slippage
Seam Problems
 SEAM PROBLEMS

 SEAM PUCKER

• Bad tension
• Bad feed
• Fabric-Thread instability
• Uneven shrinkage during finishing
• Thread-bloat from washing

• Structural jamming/Inherent pucker

• Tight weaving does not have enough room between yarns for thread
• Sewing caused yarns to be pushed out of place
 Seam Problems

Grinning

• Loose tension
• Incorrect stitch choice
• Lockstitch is the tightest stitch and will grin less than
other stitches
 Seam Problems
 SKIPPED STITCHES

• Bad tension
• Machine timing is off
• Bobbin hook or looper is not entering needle thread loop at
• correct time

• Incorrect needle choice

• The wrong needle can cause problems in creating the needle
• thread loop

• Damaged needle
• If the needle is bent, or is striking the throat plate, it may not
create the loop in the right place for the hook to catch
 Seam Problems
 NEEDLE THREAD BREAKAGE

• Tight tension
• Trapping at package base
• Snarling before tension disc
• Poor needle choice
• If eye is too small, there will be increased friction

• Excessive heat
• Poor quality thread
 Seam Problems

BOBBIN/LOOPER THREAD BREAKAGE

•Tight tension
•Badly wound bobbin
•Incorrect fit of bobbin case
•Trapping at package base (for loopers)
NEEDLE DAMAGE

•Incorrect needle/thread choice

•Damaged needle
 Seam Problems
 SEAM SLIPPAGE

• Problem is with the fabric – not the stitch

• Low yarn count, and continuous filament yarns that don’t grip each other
well are to blame
• Very minimal improvement can be achieved through increasing seam
allowance, adding top stitching, or changing to a lapped felled seam
• When possible, seams can be fused
• Best option – Change fabric
Thank You