Introduction to Arduino

PWR IN USB
(to Computer)

RESET

SCL\SDA
(I2C Bus)

POWER
5V / 3.3V / GND
Digital I\O
PWM(3, 5, 6, 9, 10, 11)

Analog
INPUTS
 PWR IN USB
(to Computer)

RESET

SCL\SDA
(I2C Bus)

POWER
5V / 3.3V / GND
Digital I\O
PWM(3, 5, 6, 9, 10, 11)

Analog
INPUTS
Go ahead and plug your board in!
Arduino Shields
PCB Built Shield Inserted Shield
Arduino Shields

Micro SD MP3 Trigger LCD

SIK Components
Name Image Type Function Notes
Push Button Digital Input Switch - Closes Polarized, needs
or opens circuit resistor
Trim Analog Input Variable resistor Also called a
Trimpot.
potentiometer
Photoresistor Analog Input Light Dependent Resistance varies
Resistor (LDR) with light.
Relay Digital Output Switch driven by Used to control
a small signal larger voltages
Temp Sensor Analog Input Temp Dependent
Resistor
Flex Sensor Analog Input Variable resistor

Soft Trimpot Analog Input Variable resistor Careful of shorts

RGB LED Dig & Analog 16,777,216 Ooh... So pretty.

Output different colors
SIK Components
SIK Components
SIK Components
Electricity \ Electronics Basic Concept
Review
• Ohms Law
• Voltage
• Current
• Resistance
• Using a Multi-meter
Ohm’s Law
Electrical Properties
Current Flow Analogy

High Current Low Current

Voltage Analogy

Water
Tower
Water
Tower

V
V

More Energy == Higher Voltage Less Energy == Lower Voltage

Resistance Analogy

Water Water
Tower Tower

Big Pipe == Lower Resistance Small Pipe == Higher Resistance

Continuity – Is it a Circuit?

The word “circuit” is derived from the circle. An Electrical

Circuit must have a continuous LOOP from Power (Vcc) to
Ground (GND).

Continuity is important to make portions of circuits are

connect. Continuity is the simplest and possibly the most
important setting on your multi-meter. Sometimes we call
this “ringing out” a circuit.
Measuring Electricity – Voltage

 Voltage is a measure of potential electrical

energy. A voltage is also called a potential
difference – it is measured between two points in
a circuit – across a device.
Measuring Electricity -- Current

Current is the measure of the rate of charge flow. For

Electrical Engineers – we consider this to be the
movement of electrons.
In order to measure this – you must break the circuit or
insert the meter in-line (series).
Measuring Electricity -- Resistance

Resistance is the measure of how much opposition to current

flow is in a circuit.
Components should be removed entirely from the circuit to
measure resistance. Note the settings on the multi-meter.
Make sure that you are set for the appropriate range.
Resistance
settings
Prototyping Circuits
Solderless Breadboard
 Oneof the most useful tools in an engineer or
Maker’s toolkit. The three most important things:
• A breadboard is easier than soldering
• A lot of those little holes are connected, which ones?
• Sometimes breadboards break
What’s a Breadboard?
Solderless Breadboard

Each row (horiz.) of 5 holes are

connected.

Verticalcolumns – called power bus

are connected vertically
Using the Breadboard to built a simple
circuit
Use the breadboard to wire up a
single LED with a 330 Ohm Resistor
(Orange-Orange-Brown).

Note: the longer leg on the

LED is the positive leg and
the shorter leg is the
negative
Fritzing View of Breadboard Circuit
What happens when you
break the circuit?
What if you wanted to add
more than one LED?
Adding control – let’s use the Arduino
and start programming!!!
Concepts: INPUT vs. OUTPUT

Referencedfrom the perspective of the microcontroller (electrical board).

Inputs is a signal / information Output is any signal exiting the
going into the board. board.

Almost all systems that use physical computing will have

some form of output

What are some examples of Outputs?

Concepts: INPUT vs. OUTPUT

Referencedfrom the perspective of the microcontroller (electrical board).

Inputs is a signal / information Output is any signal exiting the
going into the board. board.

Examples: Buttons Switches, Examples: LEDs, DC motor, servo

Light Sensors, Flex Sensors, motor, a piezo buzzer, relay, an
Humidity Sensors, Temperature RGB LED
Sensors…
Concepts: Analog vs. Digital
Microcontrollers are digital devices – ON or OFF. Also called – discrete.

analog signals are anything that can be a full range of values. What are
some examples? More on this later…

5V 5V

0V 0V
Open up Arduino

Hints:
For Mac Users 
For PC Users  1. Move the Arduino
1.Let the installer copy and executable to the dock
move the files to the for ease of access.
appropriate locations, or
2. Resist the temptation
2.Create a folder under C:\ to run these from your
Program Files (x86) called desktop.
Arduino. Move the entire
Arduino program folder
here.
 Arduino
Integrated Development Environment (IDE)

Two required functions /

methods / routines:

void setup()
{
// runs once
}

void loop()
{
// repeats
error & status messages }
Settings: Tools  Serial Port

Your computer
communicates to the Arduino
microcontroller via a serial
port  through a USB-Serial
adapter.

Check to make sure that

the drivers are properly
installed.
 Settings: Tools  Board

Next, double-check that the proper board is selected under

the ToolsBoard menu.
Arduino & Arduino Compatible Boards
BIG 6 CONCEPTS

This work is licensed under a Creative Commons Attribution-ShareAlike 3.0 United States License.
Let’s get to coding…

Project #1 – Blink
“Hello World” of Physical Computing

 Psuedo-code – how should this work?

Comments, Comments, Comments
 Comments are for you – the programmer and your
friends…or anyone else human that might read your
code.

 // this is for single line comments

 // it’s good to put a description at the
top and before anything ‘tricky’
 /* this is for multi-line comments
 Like this…
 And this….
 */
comments
Three commands to know…

 pinMode(pin, INPUT/OUTPUT);
 ex: pinMode(13, OUTPUT);

 digitalWrite(pin, HIGH/LOW);
 ex: digitalWrite(13, HIGH);

 delay(time_ms);
 ex: delay(2500); // delay of 2.5 sec.

 // NOTE: -> commands are CASE-sensitive

Project #1: Wiring Diagram

Move the green

wire from the
power bus to pin
13 (or any other
Digital I/O pin on
the Arduino
board.

Image created in Fritzing

A few simple challenges
Let’s make LED#13 blink!
 Challenge 1a – blink with a 200 ms second interval.

 Challenge 1b – blink to mimic a heartbeat

 Challenge 1c – find the fastest blink that the human eye can still detect…
 1 ms delay? 2 ms delay? 3 ms delay???

Try adding other LEDs
Programming Concepts: Variables

Variable Scope

Global
---

Function-
level
Programming Concepts: Variable Types

 Variable Types:

8 bits 16 bits 32 bits

byte int long

char unsigned int unsigned long
float
Fading in and Fading Out
(Analog or Digital?)
 A few pins on the Arduino allow for us to modify the output to mimic an
analog signal.

 This is done by a technique called:

 Pulse Width Modulation (PWM)
Concepts: Analog vs. Digital
Tocreate an analog signal, the microcontroller uses a technique called
PWM. By varying the duty cycle, we can mimic an “average” analog voltage.

Pulse Width Modulation (PWM)

 Project #2 – Fading
Introducing a new command…

analogWrite(pin, val);


pin – refers to the OUTPUT

pin (limited to pins 3, 5, 6, 9,
10, 11.) – denoted by a ~ symbol

val – 8 bit value (0 – 255).

 0 => 0V | 255 => 5V
Move one of your LED pins over to Pin 9
 In Arduino, open up:
 File  Examples  01.Basics  Fade
Fade - Code Review
Fade - Code Review
Project# 2 -- Fading

 Challenge 2a – Change the rate of the fading in and out. There are at least
two different ways to do this – can you figure them out?

 Challenge 2b – Use 2 (or more) LEDs – so that one fades in as the other one
fades out.
R G B
Color Mixing
Tri-color LED

 In the SIK, this is a standard – Common Cathode LED

 This means the negative side of the LED is all tied

to Ground.
Project 3 – RGB LED

 Note: The
longest leg of
the RGB LED is
the Common
Cathode. This
goes to GND.

Use pins 5, 6, & 9

How many unique colors can you create?

Use Colorpicker.com or
experiment on your
own.
Pick out a few colors that
you want to try re-
creating for a lamp or
lighting display...
Play around with this with
the analogWrite()
command.
RGB LED Color Mixing

 int redPin = 5;
 int greenPin = 6;
 int bluePin = 9;

 void setup()
 {
 pinMode(redPin, OUTPUT);
 pinMode(greenPin, OUTPUT);
 pinMode(bluePin, OUTPUT);
 }
RGB LED Color Mixing

 void loop()
 {
 analogWrite(redPin, 255);
 analogWrite (greenPin, 255);
 analogWrite (bluePin, 255);
 }
Project: Mood Lamp / Light Sculpture
Napkin Schematics

Emphasize the engineering

design process with
students. We like to skirt the
line between formal and
informal with a tool called
Napkin Schematics.
Napkin Schematics

Emphasize the engineering

design process with
students. We like to skirt the
line between formal and
informal with a tool called
Napkin Schematics.
Driving Motors or other High Current
Loads
 NPN Transistor (Common Emitter “Amplifier” Circuit)

to Digital
Pin 9
Input

Input is any signal entering an electrical system .

•Both digital and analog sensors are forms of input
•Input can also take many other forms: Keyboards, a mouse,
infrared sensors, biometric sensors, or just plain voltage
from a circuit
Project #4 – Digital Input

 In Arduino, open up:

 File  Examples  02.Digital  Button
Digital Sensors (a.k.a. Switches)
Pull-up Resistor (circuit)

to Digital Pin 2
Digital Sensors (a.k.a. Switches)
Add an indicator LED to Pin 13
This is just like our
1st circuit!
Digital Input
• Connect digital input to your Arduino using Pins # 0 – 13
(Although pins # 0 & 1 are also used for programming)

• Digital Input needs a pinMode command:

 pinMode (pinNumber, INPUT);
 Make sure to use ALL CAPS for INPUT

• To get a digital reading:

 int buttonState = digitalRead (pinNumber);

• Digital Input values are only HIGH (On) or LOW (Off)

Digital Sensors

• Digital sensors are more straight forward than Analog

• No matter what the sensor there are only two settings: On and
Off

• Signal is always either HIGH (On) or LOW (Off)

• Voltage signal for HIGH will be a little less than 5V on your Uno

• Voltage signal for LOW will be 0V on most systems

http://opensourcehardwarejunkies.com/tutorial-03-digitalread-and-
Programming: Conditional Statements
if()
Programming: Conditional Statements
if()

 void loop()
 {
 int buttonState =
digitalRead(5);
 if(buttonState == LOW) DIG
 { // do something INPUT
 }
 else
 { // do something else
 }
 }
Boolean Operators

<Boolean> Description
( ) == ( ) is equal?
( ) != ( ) is not equal?
( ) > ( ) greater than
( ) >= ( ) greater than or equal
( ) < ( ) less than
( ) <= ( ) less than or equal
Trimpot (Potentiometer)
Variable Resistor

fixed
end

wiper

fixed
end
Analog Sensors
3 Pin Potentiometer = var. resistor (circuit)
a.k.a. Voltage Divider Circuit

wiper

fixed
ends 1.0 V 1.0 V
Ohms Law… (just the basics)
Actually, this is the “voltage divider”
analogRead()

 Arduino uses a 10-bit A/D Converter:

• this means that you get input values from 0 to 1023
• 0V0
• 5 V  1023
 Ex:
 int sensorValue = analogRead(A0);
Using Serial Communication

 Method used to transfer data between two devices.

Data passes between the computer and Arduino
through the USB cable. Data is transmitted as zeros
(‘0’) and ones (‘1’) sequentially.

Arduino dedicates Digital I/O pin # 0 to

receiving and Digital I/O pin #1 to transmit.
Serial Monitor & analogRead()

Initializes the Serial

Communication

9600 baud data rate

prints data to serial bus
Serial Monitor & analogRead()
Opens up a
Serial Terminal
Window
Analog Sensors
2 Pin Analog Sensors = var. resistor
Take two sensors -- Use the
Serial Monitor and find the
range of input values you get
for each sensor.

MaxAnalogRead = _________

MinAnalogRead = _________
Analog Sensors

Examples:
Sensors Variables
Mic soundVolume
Photoresistor lightLevel
Potentiometer dialPosition
Temp Sensor temperature
Flex Sensor bend
Accelerometer tilt/acceleration
Additional Serial Communication
Sending a Message

 void loop ( )
 {
 Serial.print(“Hands on “) ;
 Serial.print(“Learning ”) ;
 Serial.println(“is Fun!!!”) ;

 }
 Serial Communication:
Serial Debugging

 void loop()
 {
 int xVar = 10;
 Serial.print ( “Variable xVar is “
) ;
 Serial.println ( xVar ) ;
 }
 Serial Communication:
Serial Troubleshooting

 void loop ( )
 {
 Serial.print (“Digital pin 9:
“);
 Serial.println (digitalRead(9));
 }
 Virtual Electrical Prototyping Project
started in 2007 by the Interaction Design Lab
at the University of Applied Science Potsdam, Germany

Open Source

Prototypes: Document, Share, Teach, Manufacture

 Now that you feel comfortable putting together circuits with your breadboard let’s talk about
how to go from the breadboard to a PCB
Free Time

 The rest of the class is dedicated to free pursuit

 Experiment with the various circuits and lessons in the SIK.

 Explore the additional tutorials available on learn.sparkfun.com

 Thank you for attending our Intro to Arduino class