Lecture 4

ELECTRONIC INSTRUMENTATION (EC)
(EC 452 A ) LECTURE 4
PROF O P VYAS
TOPIC
• Transducers: Construction, characteristics and circuits for common types of resistive,

capacitive, inductive, magneto-structive; piezo-electric. Photo-electric and thermo-
electric transducers for measurement of process physical variables. Various sensing
elements and transducers for measurement of Force, Pressure, Humidity, Moisture, strain,
Velocity, Acceleration and pH. Inductive and Capacitive proximity switches. Physical and
electrical loading of and by the transducer Systems.
STRAIN GAUGES
• Third B.E. Examination, 2018

•Ques 2. (b) Define gauge factor. Derive expression for gauge factor of bounded
resistance wire strain gauge.(10)
•Ques 4.A resistance wire strain gauge with a gauge factor of 2 is bounded to a steel structural
member subjected to a stress of 100 MN/m2. The modulus of elasticity of steel is 200 GN/m2.
Calculate the percentage change in the value of the gauge resistance due to the applied stress
comment upon the result. (5)
STRAIN GAUGE
• Strain gauges are devices that are commonly used by engineers to measure the effect of
external forces on an object. They measure strain directly, which can be used to indirectly
determine stress, torque, pressure, deflection, and many other measurements
• Strain is defined as compression per unit area. The primary quantities like resistance,
capacitance are measured with the strain gauge element, where force applied to any
elastic material, results in strain.
STRAIN GAUGES
• When a metal conductor is stretched or compressed, its resistance changes (as both length
and diameter of conductor change).
• Also, there is a change in the value of resistivity of the conductor when it is under strain
and this property is called piezoresistive effect. Therefore, resistance strain gauges are
also known as piezoresistive gauges.
APPLICATIONS OF STRAIN GAUGES
• The strain gauges are used for measurement of strain and associated stress in
experimental stress analysis.
• Secondly, many other detectors and transducers, notably the load cells, torque meters,
diaphragm type pressure gauges, temperature sensors, accelerometers and flow meters,
employ strain gauges as secondary transducers.
THEORY OF STRAIN GAUGE
• If a strip of elastic material is subjected to tension, (positively strained), its length

increases while its area of cross-section decreases. Since the resistance of a conductor is
proportional to its length and inversely proportional to its area of cross-section, the
resistance of the gauge increases with positive strain.
• The change in the value of resistance of strained conductor is more than what can be
accounted for an increase in resistance due to dimensional changes. The extra change in
the value of resistance is attributed to a change in the value of resistivity of a conductor
when strained. This property is known as piezoresistive effect.
TENSILE FORCE (POSITIVE STRAIN)
Change in dimension of the conductor

CIRCUIT DIAGRAM
CONSTRUCTION
DERIVATION FOR GAUGE FACTOR
• Let us consider a strain gauge made of circular wire having the dimensions : length = L,
area = A, diameter = D before being strained. The material of the wire has a resistivity ρ.
• Resistance of unstrained gauge R = ρ L/ A.
• A tensile stress s is applied to the wire. This produces a positive strain causing the length
to increase and area to decrease. Let Ʌ L = change in length, Ʌ A = change in area, Ʌ D =
change in diameter and Ʌ R = change in resistance.
• Differentiating R with respect to strain s we get
GAUGE FACTOR
GAUGE FACTOR
GAUGE FACTOR
GAUGE FACTOR
ʋ (nu) = poisson’s ratio

GAUGE FACTOR
• For small variations, the above relationship can

be written as: (Equation 4.)
• The gauge factor is defined as the ratio of per

unit change in resistance to per unit change in
length. (Equation 5)
GAUGE FACTOR
Equation (5) can be rearranged as equation (6)
From equation (4) and (5) we get:

Gauge Factor G F = 1 + 2 ʋ + (Ʌ ρ/ρ)/ϵ
Equation (7) =>
TYPES OF STRAIN GAUGES
•1. Unbonded metal strain gauges

•2. Bonded metal wire strain gauges
•3. Bonded metal foil strain gauges
•4. Vacuum deposited thin metal film strain gauges
•5. Sputter deposited thin metal strain gauges
•6. Bonded semiconductor strain gauges
•7. Diffused metal strain gauges.
UNBONDED METAL STRAIN GAUGE
• This gauge consists of a wire stretched between

two points in an insulating medium such as air. The
wires may be made of various copper nickel,
chrome nickel or nickel iron alloys. They are about
0.003 mm in diameter, have a gauge factor of 2 to
4 and sustain a force of 2 mN. The length of wire is
25 mm or less.
UNBONDED METAL
STRAIN GAUGE
• Wires are kept under tension, so
they do not buckle during
measurement.
• Pressure to be measured is sensed at
the diaphragm.
• Change in resistance of the wire is
measured by a Wheatstone bridge.
WORKING
• At initial preload, the strains and resistances of the four arms are nominally equal, with
the result the output voltage of the bridge, Output voltage Eo = 0 .
• Application of pressure produces a small displacement which is about 0.004 mm (full

scale), the displacement increases tension in two wires and decreases it in the other two,
thereby increase the resistance of two wires which are in tension and decreasing the
resistance of the remaining two wires. This causes an unbalance of the bridge producing
an output voltage which is proportional to the input displacement and hence to the applied
pressure
BONDED WIRE STRAIN GAUGE
• The bonded metal-wire strain gauges are used for both stress analysis and for
construction of transducers.
• A resistance wire strain gauge consists of a grid of fine resistance wire of about 0.025 mm
in diameter or less. The grid is cemented to carrier (base) which may be a thin sheet of
paper, a thin sheet of bakelite or a sheet of teflon. The wire is covered on top with a thin
sheet of material so as to prevent it from any mechanical damage. The spreading of wire
permits a uniform distribution of stress over the grid.
BONDED
WIRE
STRAIN
GAUGE
CONSTRUCTION AND WORKING
• The carrier is bonded with an adhesive material to the specimen under study. This permits
a good transfer of strain from carrier to grid of wires. The wires cannot buckle as they are
embedded in a matrix of cement and hence faithfully follow both the tensile and
compressive strains of the specimen.
CHARACTERISTICS
• For excellent and reproducible results, it is desirable that the resistance wire strain gauges
should have the following characteristics :
• i) The strain gauge should have a high value of gauge factor Gf. A high value of gauge
factor indicates a large change in resistance for a particular strain resulting in high
sensitivity.
• (ii) The resistance of the strain gauge should be as high as possible since this minimizes
the effects of undesirable variations of resistance in the measurement
• (iii) The strain gauges should have a low resistance temperature co-efficient. This is
essential to minimise errors on account of temperature variations
CHARACTERISTICS
• (iv) it should have linear characteristics i.e., the variations in resistance should be a linear
function of the strain.
• (v) The strain gauges are frequently used for dynamic measurements and hence their
frequency response should be good.
BONDED METAL
FOIL STRAIN GAUGE
• Metal foil strain gauges use identical
or similar materials to wire strain
gauges and are used today for most
general-purpose stress analysis
applications and for many
transducers.
• Instead of wire, metal foil is used
otherwise everything else remains
same.
ADVANTAGES OF FOIL TYPE STRAIN GAUGE
• Foil type gauges have a much greater heat dissipation capacity as compared with wire
wound strain gauges on account of their greater surface area for the same volume. For
this reason, they can be used for higher operating temperature range.
• Also the large surface area leads to better bonding.
• The sensing elements of foil gauges are formed from sheets less than 0.005 mm thick by
photo-etching processes, which allow greater flexibility with regard to shape.
• For foil type strain gauges, the manufacturing process also easily provides convenient
soldering tabs, which are integral to the sensing grid,
METAL FOIL STRAIN
GAUGE
• Because of photo etching process,

various designs are possible.
EXERCISE 1
• A resistance, wire strain gauge with a gauge factor of 2 is bonded to a steel structural
member subjected to a stress of 100 MN/m2 . The modulus of elasticity of steel is 200
GN/m2 . Calculate the percentage change in the value of the gauge resistance due to the
applied stress. Comment upon the results.
SOLUTION
THANKS
PROF O P VYAS

Lecture 4

Uploaded by

Copyright:

Available Formats

Lecture 4

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Lecture 4

Uploaded by

Copyright:

Available Formats

ELECTRONIC INSTRUMENTATION (EC)

(EC 452 A ) LECTURE 4

• Transducers: Construction, characteristics and circuits for common types of resistive,

• Third B.E. Examination, 2018

• If a strip of elastic material is subjected to tension, (positively strained), its length

Change in dimension of the conductor

ʋ (nu) = poisson’s ratio

• For small variations, the above relationship can

• The gauge factor is defined as the ratio of per

Equation (5) can be rearranged as equation (6)

From equation (4) and (5) we get:

•1. Unbonded metal strain gauges

• This gauge consists of a wire stretched between

• Application of pressure produces a small displacement which is about 0.004 mm (full

• Because of photo etching process,

You might also like