WO - NAST3039 - E01 - 1 UMTS Admission Control Parameter 72P

ZTE University
UMTS
Admission Control Parameter
RNC RRM Overview
Service Access Point
Service QoS
Service Re-negotiation
Reject
Request QoS
Negotiation
RRM
Common Algorithm
Overload Report Overload

Dedicate Algorithm Control
Overload Threshold
DRBC
Admission
Congestio
Control
Power Control Code n
HOM Control
Resource
RRM
Measurement RRM Measurement Decision
Report Decision Measurement Services Report
Report Admission
Cell x
Beaer QoS Cell y
Beaer QoS
© ZTE Corporation. All rights reserved

QoS Assurance and Priorities
UMTS
TE MT RAN CN CN TE
EDGE Gateway
NODE
End-to-End Service
TE/MT Local UMTS Bearer Service

UMTS Bearer Service
External Bearer
Bearer Service Service
CN Bearer
Radio Access Bearer Service
Service
Radio Bearer RAN Access Backbone

Service Bearer Service Bearer Service
Physical Physical
Radio Bearer Bearer
Service Service

Some important QoS
 Traffic Class ： conversational, streaming,interactive,and background.
 Maximum Bit Rate （ MBR ）： The Maximum bitrate is the upper limit a user or
application can accept or provide.
 Guaranteed Bit Rate (GBR) ： Describes the bitrate the UMTS bearer service shall
guarantee to the user or application.
 Traffic Handling Priority ： Within the interactive class, there is a definite need to
differentiate between bearer qualities. This is handled by using the traffic
handling priority attribute, to allow UMTS to schedule traffic accordingly.
 Allocation/Retention Priority ： Priority is used for differentiating between bearers
when performing allocation and retention of a bearer.

QoS Mapping
Traffic Class
Traffic Handling MAC logical channel priority
priority(THP) SRB > C > S > I > B
(Service Type)
Allocation/Retention
Iub/Iur
Priority(ARP)
Allocation/Retention Priority
(User Type)
Iub/Iur
Frame Handling Priority
+ Basic Priority
Scheduling Priority Indicator
Common Transport Channel Priority Indicator
DCH/HSPA/MBMS
+ Scheduling Priority
(Bearer Type)
Data Rate + Application Priortiy

Basic Priority (BP) Mapping
 BP is mapped from the Traffic Class, ARP Seg, THP Seg of I services. It is divided into 16 levels
(0 - 15, with the 15 the highest level, 0 the lowest)
 When the RNC receives the ARP and THP assigned by the core network, it maps the BP based
on the Traffic Class, ARP, and THP.
 Because the value range (15) of The ARP and THP 、 the classes of Traffic Class is far
beyond the value range (15) of BP, the values of the ARP and THP are segmented.
 BP is used for Admission Control and HSPA Scheduling
Abbreviated name Parameter name Example

ARPSegNum ARP Segment Number 3
ARPThresh ARP Segment Threshold [5, 10]
THPSegNum THP Segment Number 3
THPThresh THP Segment Threshold [5, 10]

Basic Priority Mapping Example
 Request services:
ARP TrafficClass
2 B
TrafficClass
ARP(RAB) ARPSeg SIP C_Voice C_Video S I (THP) B

1~5 6~10 11~15
2 1 15 14 14 10 9 8 7 7
7 2 15 13 13 10 6 5 4 4
11 3 15 12 12 10 3 2 1 0

Scheduling Priority Mapping
 SP (SchPrio) is mapped from the BasicPrio and BearerType. It can be

divided into 16 levels (0 -15, with the 15 the highest level, 0 the lowest).
 Compared with BP, the SP takes one more factor – bearer type - into
consideration to differentiate the priorities of different bearer types.
 The SP is used to schedule the call queue and to select the subscriber to
be released in forced release.
Abbreviated name Parameter name
SchPriIndex(Utran Cell) Scheduling Priority Index
SchPriIndex(Scheduling Priority) Scheduling Priority Index
BasicPrio Basic Priority
BearerType Radio Bearer Type
SchPrio Scheduling Priority

Scheduling Priority Mapping Example
 Request services: SchPriIndex

1
BearerType
BasicPrio
DCH HSPA MBMS
ARP Traffic RNC allocate 0 0 1 2
Class services
1 1 2 3
2 B HSDPA
2 2 3 4
3 3 4 5
4 4 5 6
5 5 6 7
6 6 7 8
7 7 8 9
8 8 9 10
9 9 10 11

Application Priority (AP) Mapping
 The AP is mapped from the BPSeg, BearerType, and RateSeg, including 16 levels (0 - 15, with
the 15 the highest level, 0 the lowest).
 The AP involves two application scenarios:
 Congestion control priority, which is used to select a subscriber for rate decrease and
schedule the DRBC queue in the congestion control process.
 Load control priority, which is used for reducing load when the system is overloaded
Abbreviated name Parameter name

LdCtlPriIndex Application Priority Index - Load Control
CgtCtlPriIndex Application Priority Index - Congestion
Control
AppPriIndex Application Priority Index
BPSeg Basic Priority Segment
BearerType Radio Bearer Type
RateSeg Rate Segment
AppPri Application Priority

Application Priority (AP) Mapping Example
ARP Traffic RNC allocate Services Real –time
Request Class services rate
services: 2 B DCH/DCH 128 kbit/s
1 1 1 1
BP 0 1 2 3 4 5 6 7 8 9 0 1 12 3 4 15
BPSeg 1 2 3 4 5
Rate (DL) ≤8 8~64 64~128 128~384 >384
RateSeg 1 2 3 4 5
BearerType
DCH HSPA MBMS
Rate
Seg BPSeg
1 2 3 4 5 1 2 3 4 5 1 2 3 4 5
1 4 5 6 7 8 5 6 7 8 9 11 12 13 14 15
2 3 4 5 6 7 4 5 6 7 8 11 12 13 14 15
3 2 3 4 5 6 3 4 5 6 7 11 12 13 14 15
4 1 2 3 4 5 2 3 4 5 6 10 11 12 13 14
5 0 1 2 3 4 1 2 3 4 5 10 11 12 13 14

QoS Differentiation of Admission Control
 Different admission thresholds can be set in admission control based on

BP and different transmission channels.
 Operator can determine the degree of difficulty to be admitted for
users/services with different ARPs by setting different admission
thresholds for different priorities. For example, when the load is heavy,
Operator can admit users with higher priority and refuse those with
lower priorities, so as to avoid impact on service quality of higher-
priority users caused by lower-priority user admission.
Current system
BasicPrio DchDlAcThresh Decision
load
7 95% Admit
90%
2 85% Refuse

QoS Differentiation of Congestion Control
 In the event of system congestion, resource
preemption can be triggered to reflect superiority of
subscribers with higher priorities and improve call
successful ratio. Its main policies consist of two
aspects as follows:
 Forced release: The services capable of preemption
with higher priorities are allowed to release forcibly
those services with lower priorities. That is, the
subscribers with higher priorities can implement fast
access by preempting the resources of those
subscribers who are of lower priorities and subjected
to forced release. This is to reflect differentiation of
services between subscribers.
 Downgrade: This policy is used to improve call
successful ratio by decreasing the data bit rate of
online subscribers.

-Forced release
 Forced release: selection of users to be released forcibly and
priority judgment between users originated forced release and
users to be released forcibly are based on the SP.
 There are three users in the network: UE1, UE2, and UE3. Now
UE4 wants to be admitted to the network. However, the network
is now congested.
Users PCI PVI SchPrio

UE1 N. Y 2
UE2 Y Y 5
UE3 Y N. 13
UE4 Y Y 7

- Rate Decrease
 Rate Decrease : selection of users whose rate is to be decreased in the
rate decrease is based on comparison between APs. And AP reflects ARP.
Therefore, ARP differentiation is reflected in the preceding strategy.
 There are three online users: UE1, UE2, and UE3. Suppose that a new
user UE4 requires access to the network, which is now congested due to
insufficient downlink power resources in the cell.
Real-time Rate DlNormBitRate

Users AppPri
(kbit/s) (kbit/s)
UE1 8 16 2
UE2 128 32 5
UE3 128 32 7
UE4 - 64 13

- Admission Scheduling
 Rate Decrease : For a user with preemption capability but failed
to release forcibly or without preemption capability but with
queuing capability, when his service admission is rejected, the
system can place the user/service in a queue waiting for
resources for re-access.
 Assume that three new call requests are congested.
Users QA SchPrio
UE1 N. 2
UE2 Y 7
UE3 Y 13

QoS Differentiation of Load Control
 Load control have the following means of load reduction: data

rate decrease of PS/AMR service, forced handover, forced I/B
service handover to the CELL_FACH, forced call drop, etc.
 Suppose that the cell is overloaded. There are two online users:
UE1 and UE2.
Users AppPri
UE1 2
UE2 7

Summary of Scenarios Applied for BP\SP\AP
Priority Function Scenarios
Basic Admission (1) When RAB is admitted, RNC obtains admission
Priority(BP) Control threshold based on BP.
HSDPA Packet (2) For HSDPA, when resources for HSDPA are
Scheduling shared by multiple users, RAN (Node B) will allocate
HSUPA Packet the code and power resources to different HSDPA
Scheduling mobiles according to SPI which is equal to BP.
(3) For HSUPA, when resources for HSUPA are
shared by multiple users, RAN (Node B) will allocate
the grant to different HSUPA mobiles according to
SPI which is equal to BP.
SP of Congestion (1) When forced release is performed because of
RNC(SP) Control resource congestion, RNC will select users to
perform forced release based on SP.
(2) When queueing and service admission again are
performed because of resource congestion, RNC will
select users to perform admission based on SP.
Application Congestion When downgrading is performed because of
Priority(AP) Control resource congestion, RNC will select users to
OverLoad perform downgrading based on AP.
Control When overload happens, RNC will select users to
decrease load based on AP.

Admission Control - FACH CAC Tolerable
Minimum Bit Rate

Admission Control - FACH CAC Tolerable
Minimum Bit Rate
Parameter name FACH CAC Tolerable Minimum Bit Rate
Abbreviated name FachCACToMinRate
This parameter indicates the minimum tolerable data rate
threshold for new traffic accessing the FACH. If the data rate
Description of each service on the FACH is lower than the value
indicated by this parameter because of overload on FACH,
new traffic will be refused to access the FACH.
Range and Step (100,200,…,14400)bps ， step 100bps
Unit bps
Default Value (note) 1000 bps
View  Configuration Management  RNC NE  RNC
Radio Resource Management  Modify Advanced
OMCR Interface Path
Parameter  FACH Traffic Control Information  FACH CAC
Tolerable Minimum Bit Rate (bps)

Admission Control - Cell Uplink Admission
Control Switch

Control Switch
Parameter
Cell Uplink Admission Control Switch
name
Abbreviated
UlCacSwitch
name
This parameter indicates whether uplink access
Description
control is open or closed for the cell.
0: Closed
Range and Step
1: Open
Unit N/A
Default Value
0: closed
(note)
ViewConfiguration ManagementRNC NERNC
Radio
OMCR Interface
Resource ManagementUltranCellUltranCellXXX
Path
Modify Advanced ParameterCell-Realted Access
Control UlCacSwitch

Control Switch

Admission Control - Cell Downlink Admission
Control Switch
Parameter name Cell Downlink Admission Control Switch
Abbreviated
DlCacSwitch
name
This parameter indicates whether downlink access
Description
control is open or closed for the cell.
0: Closed
Range and Step
1: Open
Unit N/A
Default Value
1: open
(note)
Radio Resource
OMCR Interface
Path ManagementUltranCellUltranCellXXX Modify
Advanced ParameterCell-Realted Access Control
DlCacSwitch

Admission Control - Cell Maximum Transmission
Power

Admission Control - Cell Maximum Transmission
Power
Parameter name Cell Maximum Transmission Power
Abbreviated
Cell Maximum Transmission Power
name
This parameter indicates the maximum value for the linear
Description sum of the power of all downlink physical channels, which is
allowed to be used in a cell.
OMCR ：［ 0.0 ， 50.0 ］ dBm ， step 0.1dBm
Range and Step
RNC ： D ＝ P*10 ，［ 0 ， 500 ］
Unit dBm
Default Value
43 dBm
(note)
ViewConfiguration ManagementRNC NERNC Radio
OMCR Interface
Resource ManagementUltranCellUltranCellXXX Cell
Path
Setup Parameters Cell Maximum Transmission Power

Admission Control - Uplink Interference Factor
of Adjacent Cells to Current Cell

Admission Control - Uplink Interference Factor
of Adjacent Cells to Current Cell
Uplink Interference Factor of Adjacent Cells to Current
Parameter name
Cell
Abbreviated UlInterFactor
name
This parameter indicates the uplink interference factor of
Description adjacent cells to current cell. It is the ratio of interference
of the neighboring cell load to self cell load.
Range and Step [0.01, 2] step0.01
Unit N/A
Default Value
0.5
(note)
Radio Resource
OMCR Interface
ManagementUltranCellUltranCellXXXModify
Path
Advanced ParameterCell-Realted Access Control
UlInterFactor
Admission Control - Background Noise Adjust
Switch

Admission Control - Background Noise Adjust
Switch
Parameter
Background Noise Adjust Switch
name
Abbreviated
BckNoiseAdjSwh
name
This parameter indicates whether background noise
Description
adjustment is open or not.
Range and 0: Closed
Step 1: Open
Unit N/A
Default Value
1: Open
(note)
Radio Resource
OMCR
Interface Path
Advanced ParameterCell-Realted Access
ControlBckNoiseAdjSwh
Admission Control - Original Background Noise

Admission Control - Original Background Noise
Parameter
Original Background Noise
name
Abbreviated
OriBckNoise
name
This parameter indicates the original background
Description noise, which is the default configuration of
background noise when cell is setup.
Range and
[-112, -50] dBm step 0.1dBm
Step
Unit dBm
Default Value
-105.5 dBm
(note)
ViewConfiguration ManagementRNC
NERNC Radio Resource
OMCR
Interface Path
ControlOriBckNoise

Admission Control - Basic Priority AC Index

Admission Control - Basic Priority AC Index
Parameter name Basic Priority AC Index
Abbreviated
BPriACIndex
name
This parameter indicates the index of the configuration
of the set of the admission control parameters based on
the Basic Priority. Different requirements make different
Description configurations of the parameters. And different cell can
use this parameter to index different configuration. The
set of parameters corresponding to this index is mapped
from the Basic Priority.
Range and Step [0…..255]
Unit N/A
Default Value
1
(note)
View  Configuration Management  RNC NERNC
OMCR Interface Radio Resource Management  UltranCell  Modify
Path Advanced Parameter UltranCellXXX  UtranCell 
Basic Priority AC Index
Admission Control - Default Cpich Ec/N0 （ d
B）

Admission Control - Default Cpich Ec/N0 （ d
B）
Parameter name Default Cpich Ec/N0 （ dB ）
Abbreviated
CpichEcN0
name
This parameter indicates the default CPICH Ec/No. It is
Description used to predict the power increasement of new
downlink service request in call admission control.
Range and Step [-24, 0] step 0.5dB
Unit dB
Default Value
-7.0
(note)
Radio Resource
OMCR Interface
Path
ControlDefault Cpich EcN0 （ dB ）
Admission Control - Measurement Priority of
Neighboring Cell

Admission Control - Measurement Priority of
Neighboring Cell
Parameter name Measurement Priority of Neighboring Cell
Abbreviated
Measurement Priority of Neighboring Cell
name
This parameter indicates the measurement priority of the
Description neighboring cell. The highest priority is 0, the lowest
priority is 2.
Range and Step [0,1,2]
Unit N/A
Default Value
0
(note)
Resource
OMCR Interface
Path
Advanced Parameter Measurement Priority of
Neighboring Cell

Admission Control - DPCH Minimum DL
Power(dB)

Admission Control - DPCH Minimum DL
Power(dB)
Parameter name DPCH Minimum DL Power(dB)
Abbreviated
MinDLDPCHPWR
name
This parameter indicates the minimum DL transmit
power of DPCH. In the Inner power control, the power
Description
of DPCH must be bigger than this parameter. If not,
change the power of DPCH same with this parameter.
Range and Step [-35,15] dB step 0.1 dB
Unit dB
Default Value
-15
(note)
ViewConfiguration Management Rnc Radio
OMCR Interface Resource ManagementModify Advanced Parameter
Path Power Control Related to Servevice and Diversity
Mode  DPCH Minimum DL Power(dB)

Admission Control - CPICH Ec/No Reporting
Indicator(Intra)

Indicator(Intra)
Parameter name CPICH Ec/No Reporting Indicator(Intra)
Abbreviated
IntraEcNoRptInd
name
This parameter indicates whether UE should
Description report the measurement result based on the
measurement quantity CPICH Ec/No.
0: False (No Report)
Range and Step
1: True (Report)
Unit N/A
Default Value
1: True
(note)
ViewConfiguration ManagementRNC
NERNC Radio Resource Management Modify
OMCR Interface
Advanced ParameterUE Intra-frquence
Path
Measurement Configuration CPICH Ec/No
Reporting Indicator
Admission Control - CPICH RSCP Reporting
Indicator(Intra)
Parameter name CPICH RSCP Reporting Indicator(Intra)
Abbreviated
IntraRSCPRptInd
name
This parameter indicates whether UE should report the
Description measurement result based on the measurement quantity
CPICH RSCP.
Range and Step
1: True (Report)
Unit N/A
Default Value
1: True
(note)
OMCR Interface Radio Resource Management Modify Advanced
Path ParameterUE Intra-frquence Measurement
ConfigurationCPICH RSCP Reporting Indicator

Admission Control - Pathloss reporting
indicator(Intra)
Parameter name Pathloss reporting indicator(Intra)
Abbreviated
IntraPathlossRptInd
name
This parameter indicates whether UE should report the
Description measurement result based on the measurement quantity
pathloss.
0: False
Range and Step
1: True
Unit N/A
Default Value
true
(note)
Path ParameterUE Intra-frquence Measurement
Configuration Pathloss reporting indicator

Indicator(Inter)

Indicator(Inter)
Parameter name CPICH Ec/No Reporting Indicator(Inter)
Abbreviated name InterEcNoRptInd
This parameter indicates whether the report of the CPICH Ec/No is

Description requested or not. This parameter is only valid to the cells of non-used
frequencies.
0: False (Not Report )

Range and Step
1: True (Report)
Unit N/A
Default Value (note) 1: True (Report)
ViewConfiguration ManagementRNC NERNC Radio Resource

OMCR Interface Path Management Modify Advanced ParameterUE Inter-frquence
Measurement Configuration CPICH Ec/No Reporting Indicator

Admission Control - CPICH RSCP Reporting
Indicator(Inter)
Parameter name CPICH RSCP Reporting Indicator(Inter)
Abbreviated name InterRSCPRptInd
This parameter indicates whether the report of the CPICH RSCP

Description is requested or not. This parameter is only valid to the cells of
non-used frequencies.
Range and Step
1: True (Report)
Unit N/A
Default Value
1: True (Report)
(note)
OMCR Interface Resource Management Modify Advanced ParameterUE
Path Inter-frquence Measurement ConfigurationCPICH RSCP
Reporting Indicator

Admission Control - Pathloss reporting
indicator(Inter)
Parameter name Pathloss reporting indicator(Inter)
Abbreviated
InterPathlossRptInd
name
This parameter indicates whether the report of the
Description CPICH Ec/No is requested or not. This parameter is only
valid to the cells of non-used frequencies.
0: False (Not Report )
Range and Step
1: True (Report)
Unit N/A
Default Value
1: True (Report)
(note)
Path ParameterUE Inter-frquence Measurement
ConfigurationPathloss reporting indicator

Admission Control - P-CPICH Power

Admission Control - P-CPICH Power
Parameter name P-CPICH Power

Abbreviated
P-CPICH Power
name
This parameter indicate the level of the P-CPICH power,
Description
default if 33dBm
Range and Step [-10,50]
Unit dBm
Default Value
-33 dBm
(note)
Configuration Management  Rnc Radio Resource
OMCR Interface
Management UtranCell UtranCell
Path
xxCellSetupParameters P-CPICH Power

Admission Control - Nominal Pathloss

Admission Control - Nominal Pathloss
Parameter
Nominal Pathloss
name
Abbreviated
Pathloss
name
This parameter indicate the default value of
Description pathloss.
If can not get the pathloss, use this one instead.
Range and
[46,158]
Step
Unit dB
Default Value
130 dB
(note)
Configuration Management RNC NE  Rnc
OMCR Radio Resource Management UtranCell
Interface Path UtranCell xxModify Advanced Parameter Cell-
Realted Access Control Nominal Pathloss

Admission Control - Intra-frequency Reporting
Quantity for RACH Reporting Configuration Tag

Admission Control - Intra-frequency Reporting
Quantity for RACH Reporting Configuration Tag
Intra-frequency Reporting Quantity for RACH Reporting
Parameter name
Configuration Tag
Abbreviated name IntraRACHRptQpRe
This parameter indicate that if the UE will support the report of

Description
the quality of target cell. Default value is 1: true (report)
0: false (no report)
Range and Step
1: true (report)
Unit N/A
Default Value
1: true (report)
(note)
Configuration Management RNC NE  Rnc Radio Resource
Management UtranCell UtranCell xxModify Advanced
OMCR Interface
ParameterUE Measurement Configuration In System
Path
Information Block Intra-frequency Reporting Quantity for
RACH Reporting Configuration Tag

Admission Control - Maximum Number of Reported
Cells on RACH Configuration Tag
Maximum Number of Reported Cells on RACH
Parameter name
Configuration Tag
Abbreviated name RACHMaxRptCelPre
This parameter indicate that if the parameter in RACH of

Description Maximum number for the cell has been configured. Default
value is 1:true (configured)
0:false (no configured)
Range and Step
1:true (configured)
Unit N/A
Default Value
1:true (configured)
(note)
Configuration Management  RNC NE  Rnc Radio Resource
Management UtranCell UtranCell xxModify Advanced
OMCR Interface
ParameterUE Measurement Configuration In System
Path
Information Block Maximum Number of Reported Cells on
RACH Configuration Tag

Admission Control - Maximum Number of
Reported Cells on RACH

Admission Control - Maximum Number of Reported
Cells on RACH
Parameter name Maximum Number of Reported Cells on RACH
Abbreviated name RACHMaxRptCell
This parameter defined the maximum number of cell
Description whose quality is reported by RACH. Default value is
Current cell.
No Report
Current Cell
Current Cell+ Best Cell
Current Cell+ 2Best Cell
Range and Step
Unit N/A
Default Value (note) Current Cell
Configuration Management  RNC NE  Rnc Radio
Resource Management UtranCell UtranCell
OMCR Interface Path xxModify Advanced ParameterUE Measurement
Configuration In System Information Block Maximum
Number of Reported Cells on RACH
Admission Control - RACH Reporting Quantity

Admission Control - RACH Reporting Quantity
Parameter name RACH Reporting Quantity

Abbreviated RptQuan
name
Description This parameter indicate which parameter is used to

report the quality of RACH.
CPICH Ec/No
Range and Step CPICH RSCP
Pathloss
UTRA Carrier RSSI
Unit N/A
Default Value CPICH Ec/No
(note)
OMCR Interface Resource Management UtranCell UtranCell
Path xxModify Advanced ParameterUE Measurement
Configuration In System Information Block RACH
Reporting Quantity

Admission Control - HsdschTrafLimit

Admission Control - HsdschTrafLimit
Parameter name HS-DSCH Traffic Limit
Abbreviated HsdschTrafLimit
name
Description This parameter indicates the maximum number of HS-

DSCH users in the cell.
Range and Step 0..65535
Unit N/A
Default Value 64
(note)

Path xxModify Advanced ParameterHSPA Configuration
Information In A cell  HS-DSCH Traffic Limit

Admission Control - EdchTrafLimit
Parameter name E-DCH Traffic Number Limit
Abbreviated
EdchTrafLimit
name
This parameter indicates the maximum number of E-
Description
DCH users in the cell.
Unit N/A
Default Value
64
(note)
Path xxModify Advanced Parameter HSPA Configuration
Information In A cell  E-DCH Traffic Number Limit

Admission Control – Qos configuration-Basic
Priority Access Control

Admission Control - BasicPrio
Parameter name Basic Priority Used in Admission Control
Abbreviated
BasicPrio
name
This parameter indicates the Basic Priority (BP) which
represents the service priority. It is mapped from RAB
Description
parameters such as ARP, traffic class and THP. The
larger the BasicPrio is, the higher priority it represents.
Unit N/A
Default Value
Refer to next Slide
(note)
ViewConfiguration ManagementRNC NEQOS
OMCR Interface ConfigurationBasic Priority Access Control Advanced
Path Parameter Checking Basic Priority (Basic Priority
Used in Admission Control)

Admission Control – BasicPrio Configuration
Traffic Class
ARP
Strea Backgr THP THP THP
Voice Video SIP
ming ound 1~5 6~10 11~15
1~5 14 14 10 7 9 8 7 15
6~10 13 13 10 4 6 5 4 15
11~15 12 12 10 0 3 2 1 15

Admission Control – DCH DL AC Threshold
Parameter
DCH Downlink Ac Threshold
name
Abbreviated
DchDlAcThresh
name
This parameter indicates the downlink TCP threshold for
DCH admission. If the downlink power exceeds (cell max
Description
transmit power)*DchDlAcThresh, the new service request
on DCH will not be admitted.
Range and
(1.. 100)% step 1%
Step
Unit %
Default Value
Refer to Slide 10
(note)
ViewConfiguration ManagementRNC NEQos
OMCR
ConfigurationBasic Priority Access Control Advanced
Interface Path
ParameterChecking DCH Downlink Ac Threshold(%)

Admission Control – DCH UL AC Threshold
Parameter name DCH Uplink Ac Threshold
Abbreviated
DchUlAcThresh
name
This parameter indicates the uplink RTWP threshold for
DCH admission control. If the uplink interference
Description
exceeds (background noise + DchUlAcThresh), the new
service request on DCH will not be admitted.
Range and Step (0.. 62)dB step 0.1
Unit dB
Default Value
Refer to Slide 10
(note)
OMCR Interface ConfigurationBasic Priority Access Control Advanced
Path ParameterChecking DCH Uplink Ac Threshold
(dB)

Admission Control - HsdpaAcThresh
Parameter name HSDPA AC Threshold
Abbreviated
HsdpaAcThresh
name
This parameter indicates the downlink TCP threshold for

HS-DSCH admission. If the downlink power exceeds
Description
(cell max transmit power)* HsdpaAcThresh, the new
service requested on HS-DSCH will not be admitted.
Range and Step (1.. 100)% step 1%

Unit %
Default Value
Refer to Slide 10
(note)
OMCR Interface
Path
ParameterChecking HSDPA AC Threshold(%)

Admission Control – E-DCH AC Threshold
Parameter name E-DCH AC Threshold
Abbreviated
EdchAcThresh
name
This parameter indicates the uplink RTWP threshold for
E-DCH admission. If the uplink interference exceeds
Description
(background noise + EdchAcThresh), , the new service
requested on E-DCH will not be admitted.
Range and Step (0.. 62)dB step 0.1
Unit dB
Default Value
Refer to Slide 10
(note)
OMCR Interface
Path
ParameterChecking E-DCH AC Threshold(dB)

Admission Control – AC Parameters Default
Values
BasicPrio DchUlAcThresh DchDlAcThresh EdchAcThresh HsdpaAcThresh
0 59 dB 75% 60 dB 77%
1 59 dB 75% 60 dB 77%
2 59 dB 75% 60 dB 77%
3 59 dB 75% 60 dB 77%
4 59 dB 80% 60 dB 83%
5 59 dB 80% 60 dB 83%
6 59 dB 80% 60 dB 83%
7 59 dB 83% 60 dB 85%
8 59 dB 83% 60 dB 85%
9 60 dB 83% 61.5 dB 85%
10 60 dB 83% 61.5 dB 85%
11 60 dB 83% 61.5 dB 85%
12 60 dB 85% 61.5 dB 87%
13 60 dB 85% 61.5 dB 87%
14 60 dB 85% 61.5 dB 87%
15 60.5dB 85% 62 dB 87%
Handover 60.5 dB 90% 62 dB 90%
Users

AC, Congestion Control & QoS Parameters List
Name Default Value TRUE Value
BasicPrio 0 0
DchUlAcThresh Refer to Slide 10 Refer to Slide 10
DchDlAcThresh Refer to Slide 10 Refer to Slide 10
HsdschTrafLimit 64 64
HsdpaAcThresh Refer to Slide 10 Refer to Slide 10
EdchTrafLimit 64 64
EdchAcThresh Refer to Slide 10 Refer to Slide 10

WO - NAST3039 - E01 - 1 UMTS Admission Control Parameter 72P

Uploaded by

Copyright:

Available Formats

WO - NAST3039 - E01 - 1 UMTS Admission Control Parameter 72P

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

WO - NAST3039 - E01 - 1 UMTS Admission Control Parameter 72P

Uploaded by

Copyright:

Available Formats

ZTE University

Overload Report Overload

© ZTE Corporation. All rights reserved

TE/MT Local UMTS Bearer Service

Radio Bearer RAN Access Backbone

© ZTE Corporation. All rights reserved

© ZTE Corporation. All rights reserved

Data Rate + Application Priortiy

© ZTE Corporation. All rights reserved

Abbreviated name Parameter name Example

ARPThresh ARP Segment Threshold [5, 10]

THPSegNum THP Segment Number 3

THPThresh THP Segment Threshold [5, 10]

© ZTE Corporation. All rights reserved

ARP(RAB) ARPSeg SIP C_Voice C_Video S I (THP) B

© ZTE Corporation. All rights reserved

 SP (SchPrio) is mapped from the BasicPrio and BearerType. It can be

© ZTE Corporation. All rights reserved

 Request services: SchPriIndex

© ZTE Corporation. All rights reserved

Abbreviated name Parameter name

© ZTE Corporation. All rights reserved

© ZTE Corporation. All rights reserved

 Different admission thresholds can be set in admission control based on

© ZTE Corporation. All rights reserved

© ZTE Corporation. All rights reserved

Users PCI PVI SchPrio

© ZTE Corporation. All rights reserved

Real-time Rate DlNormBitRate

© ZTE Corporation. All rights reserved

© ZTE Corporation. All rights reserved

 Load control have the following means of load reduction: data

© ZTE Corporation. All rights reserved

© ZTE Corporation. All rights reserved

© ZTE Corporation. All rights reserved

Range and Step (100,200,…,14400)bps ， step 100bps

© ZTE Corporation. All rights reserved

© ZTE Corporation. All rights reserved

© ZTE Corporation. All rights reserved

© ZTE Corporation. All rights reserved

© ZTE Corporation. All rights reserved

© ZTE Corporation. All rights reserved

Parameter name Cell Maximum Transmission Power

© ZTE Corporation. All rights reserved

© ZTE Corporation. All rights reserved

Range and Step [0.01, 2] step0.01

© ZTE Corporation. All rights reserved

© ZTE Corporation. All rights reserved

© ZTE Corporation. All rights reserved

© ZTE Corporation. All rights reserved

© ZTE Corporation. All rights reserved

Range and Step [-24, 0] step 0.5dB

© ZTE Corporation. All rights reserved

Range and Step [0,1,2]

© ZTE Corporation. All rights reserved

© ZTE Corporation. All rights reserved

Range and Step [-35,15] dB step 0.1 dB

© ZTE Corporation. All rights reserved

© ZTE Corporation. All rights reserved