Scribd
Upload
58 views

Relay Module With Arduino

The document discusses how relays work and describes a one-channel relay module that can be connected to an Arduino. A relay uses electromagnets to switch circuits on and off and has five pins - three for the device being controlled and two to power an electromagnet coil. The one-channel relay module allows an Arduino to control high-power devices and its wiring and pinout are described.

Uploaded by

perkinjacob
Copyright
© © All Rights Reserved
Available Formats
Download as PPTX, PDF, TXT or read online on Scribd
58 views

Relay Module With Arduino

The document discusses how relays work and describes a one-channel relay module that can be connected to an Arduino. A relay uses electromagnets to switch circuits on and off and has five pins - three for the device being controlled and two to power an electromagnet coil. The one-channel relay module allows an Arduino to control high-power devices and its wiring and pinout are described.

Uploaded by

perkinjacob
Copyright
© © All Rights Reserved
Available Formats
Download as PPTX, PDF, TXT or read online on Scribd
You are on page 1/ 18

Interface One Channel

Relay Module with


Arduino
Creative Technologies 10
At the core of a relay is
an electromagnet (a wire
coil that becomes a
temporary magnet when
How Do electricity is passed
through it). A relay can
be thought of as an
Relays Work? electric lever; you turn it
on with a relatively small
current, and it turns on
another device with a
much larger current.
Here’s a small animation showing how
a relay links two circuits together.
To illustrate, think about two simple circuits: one with an electromagnet and a switch or
sensor, and the other with a magnetic switch and a light bulb.
Initially, both circuits are open, with no current flowing through them.
When a small current flows through the first circuit, the electromagnet is energized,
creating a magnetic field around it. The energized electromagnet attracts the second
circuit’s contact, closing the switch and allowing a large current to flow.
Relay Operation
A relay typically has five pins,
three of which are high voltage
terminals (NC, COM, and NO) that
connect to the device being
controlled.
The device is connected between
the COM (common) terminal and
either the NC (normally closed) or
NO (normally open) terminal,
depending on whether the device
should remain normally on or off.
Relay Operation
Between the remaining two pins (coil1 and coil2)
is a coil that acts as an electromagnet.
Normally (initial position), the COM terminal is
connected to the NC terminal and the NO terminal
is open.
When current flows through the coil, the
electromagnet becomes energized, causing the
switch’s internal contact to move. The COM then
connects to the NO terminal, disconnecting from
the NC terminal.
When the current stops flowing through the coil,
the internal contact is returned to its initial position,
re-connecting the NC terminal to the COM and re-
opening the NO terminal.
To put it another way, the relay functions as a
single-pole-double-throw switch (SPDT).
One-Channel Relay
Module Hardware
Overview
The one-channel relay module is
designed to allow your Arduino to
control a single high-powered device.
It has a relay with a maximum current
rating of 10A at 250VAC or 30VDC.
Modules with two, four, and eight
channels are also available. You can
choose the one that best meets your
needs.
LEDs

The relay module contains two


LEDs.
The power LED will light up
when the module is powered
on. The status LED will light
up when the relay is activated.
Output Terminal The high voltage terminals (NC,
COM, and NO) of the relay are
Block broken out to a screw terminal. The
device you want to control can be
connected across them.
Control Pin
On the other side of the module, there is an input
pin IN for controlling the relay. This pin is 5V logic
compatible, so if you have a microcontroller like an
Arduino, you can drive a relay with any digital
output pin.
The input pin is active low, which means that a
logic LOW activates the relay, and a logic HIGH
deactivates it.
Module Power
The module operates on 5 volts and
draws approximately 70 mA when
the relay is activated.
The module also includes a flyback
diode that is connected in parallel
with the relay coil to safely shunt
current when the relay coil is de-
energized.
One-Channel Relay Module Pinout
Wiring a
One-Channel
Relay
Module to an
Arduino
Wiring a One-Channel Relay
Module to an Arduino
•Begin by connecting the module’s VCC
pin to the Arduino’s 5V pin and the GND
pin to ground. Connect digital pin #6 to
the IN input pin.
•You’ll also need to connect the relay
module to the AC-powered device you
want to control, in this case, a lamp. You’ll
need to cut your live AC line and connect
one end of the cut wire (coming from the
wall) to COM and the other to NC or NO,
depending on what you want your device’s
initial state to be.
"Unlock the power of control with
Arduino and relay modules – where the
digital meets the physical, and innovation
sparks to life through the seamless dance
of code and circuits."

You might also like