Scribd
Upload
37 views10 pages

Water Level Indicator System Using NOT Gate - 18-36025-1

This document describes a water level indicator system using a NOT gate. The system contains LED lights that glow at different water levels to indicate when the tank is empty, partially full, or full. It uses an IC 7404, transistors, resistors, batteries, and other basic components. The NOT gate inverts the input signal so that different LEDs illuminate according to the water level. The purpose is to allow users to monitor the water level and know when to turn pumps on or off.

Uploaded by

talha6901
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PPTX, PDF, TXT or read online on Scribd
37 views10 pages

Water Level Indicator System Using NOT Gate - 18-36025-1

This document describes a water level indicator system using a NOT gate. The system contains LED lights that glow at different water levels to indicate when the tank is empty, partially full, or full. It uses an IC 7404, transistors, resistors, batteries, and other basic components. The NOT gate inverts the input signal so that different LEDs illuminate according to the water level. The purpose is to allow users to monitor the water level and know when to turn pumps on or off.

Uploaded by

talha6901
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PPTX, PDF, TXT or read online on Scribd
You are on page 1/ 10

Water Level Indicator

System Using NOT Gate


PREPARED BY:
SHIHAB MUNNA
18-36025-1
Purpose Of This Project:

 In this project I’m going to develop a system to measure


the level of tank water. Basically I want to develop a
device that can warn the user when the water level crossed
a certain level. So user can easily turn off the motor switch
to prevent the loss of water. On the contrary this device
also remind the user when the water tank is empty. So user
can turn on the motor switch to avoid inconvenience.
Equipment:

 1) IC 7404
 2) BC 547 Transistor.
 3) Resistor (10k ohm, 220 ohm)
 4) Breadboard.
 5) Jumper Wire.
 6) LED
 7) 11.1v Battery
 8) 7805 Mosfet
Simulation:
IC 7404 Internal Structure
Input Output

0 1

1 0
Working Process:

 When the water level increases and touches the sensor,


the Red LED will glow indicating that there is water
within the tank. As the water level continuous to rise
and reaches up of the tank yellow LED will glow.
When the water in the tank rises to full, the green LED
will glow and indicate that the tank is full.
([1]Redwan Ahamad, 2018) ([2]
Nazmul Hasan Tanmoy, 2019)
Cost Analysis:

 1. IC 7404 – 52 tk
 2. BC 547 Transistor – 20 tk
 3. 10kohm Resistor – 8 tk
 4. 220kohm Resistor- 8 tk
 5. 11.1v Battery- 70 tk
 6. 7805 Mosfet- 22 tk
 7. Breadboard- 50 tk
 8. Connecting Wires- 50 tk
 9. LED – 10 tk
 10. Water Container- 30 tk
 11. Delivery Charge- 80 tk
Results and discussion:

 During develop this system I have faced some problems. Say if the voltage level
is more than reference range(5v) then the IC won’t work. We know water is a
good inductor so when there is no water but if the connecting wire were wet then
then LED provide fake warning by blinking.
Reference:

 Chowdhury Akram Hossain Sir’s YouTube Channel


 1. [1] Ahamad,Redwan, Water level indicator with alarm using NOT | AND | OR
gate |, YouTube,2018
 https://www.youtube.com/watch?v=OTubFX6WmH0
 2. [2] Hasan, Tanmoy, Water level indicator using NOT gate ,YouTube,2019
 https://www.youtube.com/watch?v=8xr7wAY_RvQ

You might also like