Module 4 Conduction

Module – 4: Conduction
Thermal Engineering
Derivation of general three dimensional
conduction equations in Cartesian coordinate
Special cases
3-D conduction in cylindrical and spherical
coordinate systems
• Cylindrical Coordinates.
Spherical Coordinates
One dimensional conduction equations in
rectangular coordinate
• Consider a thin element
of thickness x in a large plane
wall, as shown in Figure.
Assume the density of the wall
is , the specific heat is C,
and the area of the wall
normal to the direction of
heat transfer is A. An energy
balance on this thin element
during a small time interval t
can be expressed as
Heat Conduction Equation in a Long
Cylinder
The Thermal Resistance Concept
Overall heat transfer coefficient
Composite walls
• In practice we often encounter plane walls that consist
of several layers of different materials. The thermal
resistance concept can still be used to determine the
rate of steady heat transfer through such composite
walls.
• Consider a plane wall that consists of two layers (such
as a brick wall with a layer of insulation). The rate of
steady heat transfer through this two-layer composite
wall can be expressed as (Fig.)
HEAT CONDUCTION IN CYLINDERS
• Then Fourier’s law of heat conduction for heat
transfer through the cylindrical layer can be
expressed as
• We can repeat the analysis above for a
spherical layer by taking A = 4 Pi r2
Composite cylinder
Thermal contact resistance
• In the analysis of heat conduction through multilayer
solids, we assumed “perfect contact” at the interface of
two layers, and thus no temperature drop at the interface.
This would be the case when the surfaces are perfectly
smooth and they produce a perfect contact at each point.
• In reality, however, even flat surfaces that appear smooth
to the eye turn out to be rather rough when examined
under a microscope, as shown in Fig., with numerous
peaks and valleys. That is, a surface is microscopically
rough no matter how smooth it appears to be.
• When two such surfaces are pressed against each other, the peaks
will form good material contact but the valleys will form voids filled
with air. As a result, an interface will contain numerous air gaps of
varying sizes that act as insulation because of the low thermal
conductivity of air.
• Thus, an interface offers some resistance to heat transfer, and this
resistance per unit interface area is called the thermal contact
resistance, Rc. The value of Rc is determined experimentally.
• Consider heat transfer through two metal rods of cross-sectional
area A that are pressed against each other. Heat transfer through
the interface of these two rods is the sum of the heat transfers
through the solid contact spots and the gaps in the noncontact
areas and can be expressed as
• It can also be expressed in an analogous
manner to Newton’s law of cooling as
• The quantity hc, which corresponds to the

convection heat transfer coefficient, is called
the thermal contact conductance and is
expressed as
Simple problems
1. Consider a 3-m-high, 5-m-wide, and 0.3-m-
thick wall whose thermal conductivity is k =
0.9 W/m · °C. On a certain day, the
temperatures of the inner and the outer
surfaces of the wall are measured to be 16°C
and 2°C, respectively. Determine the rate of
heat loss through the wall on that day.
2. Consider a 0.8-m-high and 1.5-m-wide double-pane
window consisting of two 4-mm-thick layers of glass (k =
0.78 W/m · °C) separated by a 10-mm-wide stagnant air
space (k = 0.026 W/m · °C). Determine the steady rate of
heat transfer through this double-pane window and the
temperature of its inner surface for a day during which
the room is maintained at 20°C while the temperature
of the outdoors is 10°C. Take the convection heat
transfer coefficients on the inner and outer surfaces of
the window to be h1 = 10 W/m2 · °C and h2 = 40 W/m2
· °C, which includes the effects of radiation.
3. The thermal contact conductance at the
interface of two 1-cm-thick aluminum plates is
measured to be 11,000 W/m2 · °C. Determine
the thickness of the aluminum plate whose
thermal resistance is equal to the thermal
resistance of the interface between the plates.
The thermal conductivity of aluminum at
room temperature is k = 237 W/m · °C.
4. A 3-m internal diameter spherical tank made of 2-cm-thick
stainless steel (k = 15 W/m · °C) is used to store iced water at
T∞1 = 0°C. The tank is located in a room whose temperature is
T∞2 = 22°C. The walls of the room are also at 22°C. The outer
surface of the tank is black and heat transfer between the
outer surface of the tank and the surroundings is by natural
convection and radiation. The convection heat transfer
coefficients at the inner and the outer surfaces of the tank are
h1 = 80 W/m2 · °C and h2 = 10 W/m2 · °C, respectively.
Determine (a) the rate of heat transfer to the iced water in the
tank. The outer surface of the tank is black and thus its
emissivity is ε = 1.
5. Steam at T∞1 = 320°C flows in a cast iron pipe (k = 80 W/m
· °C) whose inner and outer diameters are D1 = 5 cm and
D2 = 5.5 cm, respectively. The pipe is covered with 3-cm-
thick glass wool insulation with k = 0.05 W/m · °C. Heat is
lost to the surroundings at T∞2 = 5°C by natural convection
and radiation, with a combined heat transfer coefficient
of h2 = 18 W/m2 · °C. Taking the heat transfer coefficient
inside the pipe to be h1 = 60 W/m2 · °C, determine the
rate of heat loss from the steam per unit length of the
pipe. Also determine the temperature drops across the
pipe shell and the insulation.
Thank you

Module 4 Conduction

Uploaded by

Copyright:

Available Formats

Module 4 Conduction

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Module 4 Conduction

Uploaded by

Copyright:

Available Formats

Module – 4: Conduction

• The quantity hc, which corresponds to the

You might also like