Department of Electrical and

Electronics Engineering

Subject: Electromechanical Energy Conversion-II

Sub. Code: NEE-401
Topic: Construction & OC. SC Test of Synchronous
Machine
Faculty Name: Mrs. Kalpana Hazarika
 Principle of Operation
•The operation of a synchronous generator is based on Faraday's law
of electromagnetic induction, and in an ac synchronous generator the
generation of emf's is by relative motion of conductors and magnetic
flux.

•These machines can be used as either motors or generators but their

predominant use is in generation.

There are a number of sources of energy used to turn the turbines:-

(a) Gas (b) Steam

(c) Combined cycle (d) Nuclear
(e) Hydro (f) Wind
(g) Wave (h) Photovoltaic
Principle of Operation

Multiple
Pole
Rotor
 Principle of Operation
•In constructing a synchronous •There are two categories of Synchronous
machine a point to note is that the machines:
stator is fixed and the poles rotate.
(a) those with salient or projecting poles
(b) those with cylindrical rotors
2-pole Cylindrical Rotor A Cylindrical Rotor
 Principle of Operation

4-Pole Salient Rotor A Salient Pole Rotor

Principle of Operation
Its characteristic feature is that the
armature rotates through a stationary
magnetic field, and the generated
AC is brought to the load by means
of slip rings and brushes.

The revolving-armature alternator is

found only in alternators of small
power rating and is not generally
used. This is because a rotating
armature requires slip rings and
brushes to conduct the current from
the armature to the load.
Principle of Operation
The revolving-field type alternator
has a stationary armature and a
rotating magnetic field.

The generated voltage can be

connected directly to the load
without having to pass across the
slip rings and brushes.

The voltage applied to generate the

rotating field is a small DC voltage
(called a “field excitation” voltage)
Single Phase Alternator
A single-phase alternator has all the
armature conductors connected in series

The stator is two pole. The winding is

wound in two distinct pole groups, both
poles being wound in the same direction
around the stator frame.

The rotor also consists of two pole groups,

adjacent poles being of opposite polarity.
 Single Phase Alternator
The two poles of the stator
winding are connected to each
other so that the AC voltages
are in phase, so they add.

As the rotor (field) turns, its poles will induce AC voltages in

the stator (armature) windings. Since one rotor pole is in the
same position relative to a stator pole as any other rotor pole,
both the stator poles are cut by equal amounts of magnetic lines
of force at any time. As a result, the voltages induced in the two
poles of the stator winding have the same amplitude or value at
any given instant.
 Three Phase Alternator
The three-phase alternator has VB
three single-phase windings
spaced so that the voltage
induced in any one is phase- 120 O VA
120 O
displaced by 120 degrees from 120 O
the other two.

V
A B C VC
O
L The voltage waveforms
T generated across each phase
A are drawn on a graph phase-
G displaced 120 degrees from
E each other.
 Three Phase Alternator
•The three phases are independent of each other.

•One point from each winding can be connected to form a neutral

and thus make a wye connection.
•The voltage from this point to any one of the line leads will be the
phase voltage. The line voltage across any two line leads is the vector
sum of the individual phase voltages. The line voltage is 1.73, (3 ),
times the phase voltage.
•Since the windings form only one path for current flow between
phases, the line and phase currents are equal.
 Three Phase Alternator

•A three-phase stator can also be connected so that the phases form a

“delta” connection.

•In the delta connection the line voltages are equal to the phase
voltages, but the line currents will be equal to the vector sum of the
phase currents.

•Since the phases are 120 degrees out of phase, the line current will
be 1.73, (3 ), times the phase current. Both "wye" and the "delta"
connections are used in alternators.
Three Phase Stator Connection

A
A

B C B
C

Three Phase
T hree Phase ST AR
C o nnected
DELTA Connected
 Three Phase Alternator
•The frequency of the AC generated by an alternator depends upon
the number of poles and the speed of the rotor
•When a rotor has rotated through an angle so that two adjacent
rotor poles (a north and a south) have passed one winding, the
voltage induced in that one winding will have varied through a
complete cycle of 360 electrical degrees.

•A two pole machine must rotate at twice the speed of a four-pole

machine to generate the same frequency.
•The magnitude of the voltage generated by an alternator can be
varied by adjusting the current on the rotor which changes the
strength of the magnetic field.
 Three Phase Alternator
•A two pole alternator produces one electrical cycle for each
complete mechanical rotation.
•A four pole alternator will produce two electrical cycles for each
mechanical rotation because two north and two south poles move by
each winding on the stator for one complete revolution of the rotor.

f = (nRotor)(p/2)/60 = (nRotorp)/120
where nRotor is the speed of the rotor in revolutions per minute,
p is the number of poles
f is the electrical line frequency produced by the alternator.
The speed of the rotor must be divided by 60 to change from
revolutions per minute to revolutions per second.
Three Phase Alternator
 Three Phase Alternator
•In an alternator the output voltage varies with the load.

•There are two voltage drops.{ IR & IXL }

•The IXL drop is due to the inductive reactance of the armature
windings.
•Both the IR drop and the IXL drop decrease the output voltage as the
load increases.

•The change in voltage from no-load to full-load is called the “voltage

regulation” of an alternator.
•A constant voltage output from an alternator is maintained by
varying the field strength as required by changes in load.
 OPEN CIRCUIT CHARACTERISTICS

ZZ
FL Zs Arm ature
Field Regulator
Ea V a.c. Circuit
DC F
Source Zs Ea Zs
Z Ea
L
A
Field Current

To obtain the open circuit characteristics the machine is driven at

rated speed without the load. Readings of the line-to-line voltage
are taken for various values of field current. The voltage, except in
very low voltage machines, is stepped down by the means of a
potential transformer.
 OPEN CIRCUIT CHARACTERISTICS

Armature Phase
Voltage/V

Fie ld C u r r e n t /A
If not for the magnetic saturation of the iron, the open
circuit characteristics would be linear as represented
by the air gap line
 OPEN CIRCUIT CHARACTERISTICS

On open circuit IL = Ia = 0

Vt = E - ILZs
where Zs = Ra + jXs
and Xs = XL + Xar
On open circuit Vt = E

Alternating current produces a flux which is proportional to I L

(reduces the total flux).

This is called the armature reactance effect represented by X ar

On open circuit Xar = 0.

 SHORT CIRCUIT CHARACTERISTICS
a.c.
A
ZZ
Zs Arm ature
Field Regulator
FL

short circuit
Ea Circuit
DC F
S ource Zs Ea Zs
Z Ea
L
A
Field Current

The three terminals of the armature are short circuited

The machine is driven at approximately synchronous rated speed and
measurements of armature short circuit currents are made for various
values of field currents usually up to and above rated armature
current.
 SHORT CIRCUIT CHARACTERISTICS

On short-circuit the machine runs

) /A

at it synchronous speed (n = ns)

s.c

and IL = IFL

For s/c Vt = 0,
Short Circuit Current(I

Therefore E / IL = Zs
and Isc = IL = E / Zs

Field C urrent (I f )/A

In conventional synchronous machines the short circuit characteristics
is practically linear because the iron is unsaturated up to rated
armature current
 LOAD CONDITIONS

A
ZZ a.c. Load
FL Zs
Ea V Bank
Field Regulator

a.c.

DC F
Source Zs Ea Zs
Z Ea
Arm ature D elta/Star
L Circuit
A C onnected
Field Current

The machine is introduced to normal working conditions

 Per Phase Equivalent Circuit

Ra => armature resistance per phase

XL => leakage reactance.
Power flow out of a Synchronous Machine

Generator power
flow => out

Motor power flow

=> in
 Power flow out of a Synchronous Machine

 = Load angles
Eδ  Vt 0  I L  . jX s

In practical synchronous machines, except for small ones,

Xs >> Ra so we could assume that Zs = jXs in the analysis.
Therefore we get E = Vt + jILXs
 Power flow out of a Synchronous Machine

Power = VIcos

Considering the diagram h = ILXscos = Esin

Therefore ILXscos = Esin

 Power flow out of a Synchronous Machine

For maximum power sin = 1

Therefore  = 90

In which case