Boost-Synchronous Buck Converter

Power Factor Correction With Integrated

Circuit

MD ZUBAER HOSSAIN PROMETE PAUL POOJA

ID:1721956 ID: 1521193
INTRODUCTION
 The DC/DC converters are widely used in regulated switch mode DC power
supplies

 The DC/DC boost converter only needs four external components

 Inductor,
 Electronic switch,
 Diode and output capacitor

 A novel integrated control strategy with two different current control methods
 boost stage
 buck stage
METHODOLOGY

Single Phase Voltage Source

Boost Converter

Synchronous Buck Converter

Two Voltage Regulator

Microcontroller
Boost Converter Circuit
A boost converter is a DC-to-DC power
converter that steps up voltage from its input
to its output

It is a class of switched-mode
power supply containing

Required least two semiconductors and

at least one energy storage element: a
capacitor, inductor, or the two in
combination
Synchronous Buck Converter:

synchronous buck converter produces

a regulated voltage

Output voltage lower than its

input voltage

deliver high currents while

minimizing power loss.
Boost-Synchronous Buck Converter Circuit

Nonlinear Duty Cycle control method Q1

is proposed for Boost-Synchronous L2

1mH
D2

DIODE
IRFP250
L1
1mH
(+)

Buck converter. Q3 C3 +88.8

IRFP250 100uF +88.8 R3 R1 Volts
Volts 10 C1 10k
100uF
Q2
G2 IRFP250

D1

G1
DIODE

U2

the Boost-Synchronous Buck R2

1k
1
2
3
4
VCC
IN
SD
COM
VB
HO
VS
LO
8
7
6
5
G1

converter can work more easily as a

C2
100u IR2104
U2(SD)
G2
RV1(2)

U1

simple boost or a simple buck RV1 13

14

2
OSC1/CLKIN
OSC2/CLKOUT
RB0/INT
RB1
RB2
33
34
35
36

82%
RA0/AN0 RB3/PGM

converter
3 37
RA1/AN1 RB4
4 38
RA2/AN2/VREF-/CVREF RB5
5 39
RA3/AN3/VREF+ RB6/PGC
1k 6 40
RA4/T0CKI/C1OUT RB7/PGD
7
RA5/AN4/SS/C2OUT
15
RC0/T1OSO/T1CKI
8 16
RE0/AN5/RD RC1/T1OSI/CCP2 A
9 17
RE1/AN6/WR RC2/CCP1
10 18
RE2/AN7/CS RC3/SCK/SCL B
23
RC4/SDI/SDA
1 24
MCLR/Vpp/THV RC5/SDO C
25
RC6/TX/CK
26
RC7/RX/DT D
19
RD0/PSP0
20
RD1/PSP1
21
RD2/PSP2
22
RD3/PSP3
27
RD4/PSP4
28
RD5/PSP5
29
RD6/PSP6
30
RD7/PSP7
PIC16F877A
Proteus Simulate

Now This is Our

switching Graph
PSIM Circuit

VP1 = 139.52387
VP4 VP1
310 VP4 = 3.11135

Simulated circuit in Psim

PSIM simulated Graph

VP4 VP4

1K 1K
800 800
600 600
400 400
200 200
0 0
-200 -200

VP1 VP1
Frequency (Hz) Time (s)
500 500

400 400

300 300

200 200

100 100

0
0

0 10K 20K 30K 40K 50K 60K

0 2m 4m 6m 8m 10m
Frequency (Hz) Time (s)

Frequency domain graph plot

Time domain Graph Plot

Result Analysis

 Total harmonic distortion:

The total harmonic distortion is a measurement of the harmonic
distortion present in a signal and is defined as the ratio of the sum
of the powers of all harmonic components to the power of the
fundamental frequency.

Reduced performance of energy

generation, transport and usage
systems.
Result Analysis

THD:
Fundamental Frequency 5.0000000e+001 HZ
I1 3.3944961e+003
VP1 3.3994274e+003

PF:
Time From 1.0000000e-005
Time To 1.0000000e+000
I1 vs. VP1 1.0000000e+000
Conclusion

 A new nonlinear current control method is presented for buck

converter
 current control method and the average current control method used
in boost converter
 Theoretical analysis and experimental results show that the input
current can be well controlled
THANK YOU
EVERYONE