Chapter 1:

Introduction to the
Personal Computer

IT Essentials: care for network and

computer hardware
Chapter 1 Section Objectives
 1.1 Explain IT industry certifications
 1.2 Describe a computer system
 1.3 Identify the names, purposes, and characteristics of cases and
power supplies
 1.4 Identify the names, purposes, and characteristics of internal
components
 1.5 Identify the names, purposes, and characteristics of ports and
cables
 1.6 Identify the names, purposes, and characteristics of input
devices
 1.7 Identify the names, purposes, and characteristics of output
devices
 1.8 Explain system resources and their purposes
 IT

Information technology (IT) is the design, development,

implementation, support, and management of computer
hardware and software applications. A certified IT
professional is knowledgeable about computer systems
and operating systems. This chapter will review IT
certifications and the components of a basic personal
computer system.
Basic Personal Computer System
 A computer system consists of hardware and software
components.
 Hardware is the physical equipment such as the case,
storage drives, keyboards, monitors, cables, speakers,
and printers.
 Software is the operating
system and programs.
 The operating system
instructs the computer how
to operate.
 Programs or applications
perform different functions.
Computer Cases and Power Supplies
Computer case
 Provides protection and support for internal components
 Should be durable, easy to service, and have enough
room for expansion
 The size and layout of a case is called a form factor
Power supply
 Converts AC power from the wall socket into DC
 Must provide enough power for the installed components

and future additions

Four Basic Units of Electricity
 Voltage (V) is a measure of the force required to push
electrons through a circuit. Voltage is measured in volts. A
computer power supply usually produces several different
voltages.
 Current (I) is a measure of the amount of electrons going
through a circuit. Current is measured in amperes, or amps
(A). Computer power supplies deliver different amperages
for each output voltage.
 Power (P) is voltage multiplied by current. The
measurement is called watts (W). Computer power supplies
are rated in watts.
 Resistance (R) is the opposition to the flow of current in a
circuit. Resistance is measured in ohms. Lower resistance
allows more current to flow through a circuit.
Ohm’s Law
 There is a basic equation that expresses how three of the terms
relate to each other. It states that voltage is equal to the current
multiplied by the resistance. This is known as Ohm's Law. V = IR
 In an electrical system, power (P) is equal to the voltage multiplied
by the current. P = VI
Internal Components

 Identify the names characteristics of:

• Motherboards
• CPUs
• Cooling systems
• ROM and RAM
• Adapter cards
• Storage drives
• Internal cables
Motherboards
 The motherboard is the
main printed circuit board.
 Contains the buses, or electrical
pathways found in a computer.
Buses allow data to travel
among the various components.
 Accommodates CPU, RAM, expansion slots, heat
sink/fan assembly, BIOS chip, chip set, sockets, internal
and external connectors, various ports, and the
embedded wires that interconnect the motherboard
components.
Motherboard Form Factors
 The form factor of motherboards pertains to the size
and shape of the board.
 It also describes the physical layout of the different
components and devices on the motherboard.
 Various form factors exist for motherboards.
AT – Advanced Technology
ATX – Advanced Technology Extended
Mini-ATX – Smaller footprint of ATX
Micro-ATX – Smaller footprint of ATX
LPX – Low-profile Extended
NLX – New Low-profile Extended
BTX – Balanced Technology Extended
Central Processing Unit (CPU)
 The CPU is known as the brain of the computer. It is
also referred to as the processor.
 The CPU executes a program, which is a sequence of
stored instructions.
 Two major CPU architectures related to instruction sets:
•Reduced Instruction Set Computer (RISC)
•Complex Instruction Set Computer (CISC)
Central Processing Unit (Continued)
 Some CPUs incorporate hyperthreading to enhance the
performance of the CPU.
 The amount of data that a CPU can process at the one time
depends on the size of the processor data bus.
 Overclocking is a technique used to make a processor work at a
faster speed than its original specification.
 MMX is a set of multimedia instructions built into Intel processors.
 The latest processor technology has resulted in CPU
manufacturers finding ways to incorporate more than one CPU
core onto a single chip.
Dual core CPU, Triple Core CPU and Quad Core CPU
 Cooling Systems
 Electronic components generate
heat. Too much heat can
damage components.
 A case fan makes the cooling
process more efficient.
Case Fan
 A heat sink draws heat away
from the core of the CPU. A fan
CPU Fan on top of the heat sink moves the
heat away from the CPU.
 Fans can be dedicated to cool
the Graphics-processing unit
(GPU).
ROM and RAM
 Read-only memory (ROM)
 ROM contains the basic instructions for booting the
computer and loading the operating system are stored in
ROM.
 Random-access memory (RAM)
 RAM is temporary storage for data and programs that are
being accessed by the CPU
 RAM is volatile memory, which means that the contents are
erased when the computer is powered off
 More RAM means more capacity to hold and process large
programs and files, as well as enhance system performance.
Memory Modules
 Memory modules are memory chips that have been soldered on to a
special circuit board for easy installation and removal.
 Dual Inline Package (DIP) is an individual memory chip.
 Single Inline Memory Module (SIMM) is a small circuit board that holds
several memory chips.
 Dual Inline Memory Module (DIMM) is a circuit board that holds SDRAM,
DDR SDRAM, and DDR2 SDRAM chips.
 RAM Bus Inline Memory Module (RIMM) is a circuit board that holds
RDRAM chips.
 Small Outline DIMM (SODIMM) is a smaller, more condensed version of
DIMM which provides random access data storage that is ideal for use in
laptops, printers, and other devices where conserving space is desirable.
 The speed of memory has a direct impact on how much data a processor
can process because faster memory improves the performance of the
processor. As processor speed increases, memory speed must also
increase.
Cache and Error Checking
 Cache
• SRAM is used as cache memory to store the most frequently
used data.
• SRAM provides the processor with faster access to the data
than retrieving it from the slower DRAM, or main memory.

 Error Checking
• Memory errors occur when the data is not stored correctly in
the RAM chips.
• The computer uses different methods to detect and correct data
errors in memory.
Adapter Cards
 Adapter cards increase the functionality of a computer by
adding controllers for specific devices or by replacing
malfunctioning ports.
 Examples of adapter cards:
•Sound adapter and video adapter
•USB, parallel, and serial ports
•Network Interface Card (NIC),
wireless NIC, and modem adapter

 Types of expansion slots:

•Peripheral Component Interconnect (PCI)
•Advanced Graphics Port (AGP)
•PCI-Express
Hard Drives and Floppy Drives
 Hard drives and floppy drives read or write information to magnetic storage
media.
 They may be fixed or removable.
 The hard disk drive (HDD) is a
magnetic storage device. The storage
capacity is measured in gigabytes (GB).
 Magnetic hard drives have drive motors designed to spin magnetic platters
and move the drive heads.
 Solid state drives (SSDs) do not have moving parts, which results in faster
access to data, higher reliability, reduced power usage.

 A floppy disk drive (FDD) is storage device that

uses removable 3.5 inch floppy disks that can store
up to 1.44 MB of data.
Optical Drives, Flash Drives and Drive
Interfaces
 An optical drive is a storage device that uses lasers to
read data on the optical media. The three types are CD,
DVD and BD.
 A flash drive is a removable storage device that
connects to a USB port. A flash drive uses a type
of memory that requires no power to maintain the
data.
 Some common drive interfaces are:
•Integrated Drive Electronics (IDE)
•Enhanced Integrated Drive Electronics (EIDE)
•Parallel ATA (PATA)
•Serial ATA (SATA) and External SATA (eSATA)
•Small Computer System Interface (SCSI)
Internal Cables
 Internal power cables (Molex and Berg) connect
drives and fans to the motherboard.
 Front panel cables connect the case buttons and
lights to the motherboard.
 Data cables connect drives to the drive controller.
• Floppy disk drive (FDD) data cable
• PATA (IDE) data cable
• PATA (EIDE) data cable
• SATA data cable
• eSATA data cable
• SCSI data cable
 Ports and Cables
 Serial ports transmit one bit of data at a time.
 A telephone cable (RJ11) is used to connect a modem to a telephone
outlet.
 USB is a standard interface for connecting hot-swappable peripheral
devices to a computer. Some devices can also be powered through the
USB port.
 FireWire is a high-speed, hot-swappable interface that can support up
to 63 devices. Some devices can also be powered through the FireWire
port.
 A parallel cable is used to connect parallel devices, such as a printer or
scanner, and can transmit 8 bits of data at one time.
 A SCSI port can transmit data at rates in excess of 320 Mbps and can
support up to 15 devices. SCSI devices must be terminated at the
endpoints of the SCSI chain.
Ports and Cables (Continued)
 A network port, also known as an RJ-45 port,
connects a computer to a network. The maximum
length of network cable is 328 feet (100 m).
 A PS/2 port connects a keyboard or a mouse to a
computer. The PS/2 port is a 6-pin mini-DIN female
connector.
 An audio port connects audio devices to the
computer.
 A video port connects a monitor cable to a computer.
 Input Devices
 Input devices are used to enter data or
instructions into a computer:
• Mouse and Keyboard: are the two most commonly used input
devices. The mouse is used to navigate the graphical user
interface (GUI). The keyboard is used to enter text commands that
control the computer
• Digital camera and digital video
camera
• Biometric authentication device
• Touch screen
• Scanner :digitizes an image or document
Output Devices
 Monitors and Projectors:
• Cathode-ray tube (CRT) monitor is the most
common monitor type. Most televisions also use
this technology.
• Liquid crystal display (LCD) is commonly used
in laptops and some projectors. LCD comes in
two forms, active matrix and passive matrix.
• Digital light processing (DLP) is another
technology used in projectors.
• Monitor resolution refers to the level of image
detail that can be reproduced. Higher resolution
settings produce better image quality.
Output Devices (Continued)
 Printers and Fax Machines are output
devices that create hard copies of
computer files.
 Scanners create electronic file version
of paper documents.
 Speakers and headphones are output
devices for reproducing audio signals.

Headphones
Speakers
System Resources
 System resources are used for communication
purposes between the CPU and other components in a
computer.
 There are three common system resources:
• Interrupt Requests (IRQs)
• Input/Output (I/O) Port Addresses
• Direct Memory Access (DMA)
Chapter 1 Summary
 Information Technology encompasses the use of computers,
network hardware, and software to process, store, transmit,
and retrieve information.
 A personal computer system consists of hardware
components and software applications.
 The computer case and power supply must be chosen
carefully to support the hardware inside the case and allow
for the addition of components.
 The internal components of a computer are selected for
specific features and functions. All internal components must
be compatible with the motherboard.
 You should use the correct type of ports and cables when
connecting devices.
Chapter 1 Summary (Continued)
 Typical input devices include the keyboard, mouse, touch
screen, and digital cameras.
 Typical output devices include monitors, printers, and
speakers.
 System resources must be assigned to computer
components. System resources include IRQs, I/O port
addresses, and DMAs.