0% found this document useful (0 votes)
55 views25 pages

Unit3 Esd

The document discusses various components involved in embedded firmware design, including a reset circuit, brownout protection circuit, oscillator unit, real-time clock, and watch dog timer. It describes embedded firmware as the program and configuration settings loaded into an embedded system's memory. Embedded firmware can be developed using high-level languages like C/C++ or assembly language, and must be converted into machine-readable binary code before loading onto the target processor.
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PPTX, PDF, TXT or read online on Scribd
0% found this document useful (0 votes)
55 views25 pages

Unit3 Esd

The document discusses various components involved in embedded firmware design, including a reset circuit, brownout protection circuit, oscillator unit, real-time clock, and watch dog timer. It describes embedded firmware as the program and configuration settings loaded into an embedded system's memory. Embedded firmware can be developed using high-level languages like C/C++ or assembly language, and must be converted into machine-readable binary code before loading onto the target processor.
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PPTX, PDF, TXT or read online on Scribd
You are on page 1/ 25

UNIT-3

EMBEDDED FIRMWARE DESIGN


 Reset circuit

 Brownout protection circuit

 Oscillator unit

 Real time clock

 Watch dog timer

 Embedded firmware design approaches and development languages


Embedded firmware
 Embedded Firmware refers to the control algorithm(Program
instructions) and or the configuration settings that an embedded
system developer dumps into the code(program) memory of the
embedded systems
 There are various methods available for developing the embedded
firmware.
 1) Write the program in high level languages like Embedded C/C++
using an IDE.
 2) Write the program in assembly language using the instructions
supported by your application’s target processor/controller.
 The instruction set for each family of processor/controller is
different and the program written in either of the methods given
above should be converted into a processor-understandable
machine code before loading it into the program memory.
 The process of converting the program written in either a high-
level language or processor/controller-specific assembly code to
machine-readable binary code is called ‘HEX FILE
CREATION’
 The methods used for hex file creation are different depending
on the programming techniques used.
 If the program is written in Embedded C/C++ using an IDE, the
cross compiler included in the IDE converts it into corresponding
processor/controller understandable ‘HEX file’.
 If the program is written in Assembly language, you can use the
utilities supplied by the processor/controller vendors to convert
source code into HEX file
 SYSTEM COMPONENTS The system components refer to the
components/ICs that are necessary for the proper functioning of the
embedded system.
 Some of these circuits may be essential for the proper functioning
of the processor/controller and firmware execution
 Watchdog timer, Reset IC, Brown-out Protection IC, etc are
examples of circuits/ICs which are essential for the proper
functioning of processor/controllers
RESET CIRCUIT
 The reset circuit is essential to ensure that the device is not operating
at a voltage level where the device is not guaranteed to operate,
during system power ON.
 The reset signal brings the internal registers and the different
hardware systems of the processor/controller to known state and
starts the firmware execution from reset vector
 The reset signal can be either Active High or active Low.
 The reset signal to the processor can be applied at power ON
through an external passive reset circuit comprising a capacitor and
resistor or through a standard reset IC like MAX810 from Maxim
Dallas.
 The processor behaviour may not be predictable if the power
supply voltage falls below the recommended operating voltage.
 It may lead to situations like data corruption.
 A brown-out protection circuit holds the processor/controller in
reset state, when the operating voltage falls below the threshold,
until it rises above the threshold.
BROWN OUT RESET CIRCUIT
 The BOR circuit holds the device in Reset when VDD reaches a
selectable minimum level.
 Between the POR and BOR, complete voltage range coverage
for execution protection can be implemented.
 The Brown-out Reset module has four operating modes
controlled by the BOREN Configuration bits. The four operating
modes are:
• BOR is always on
• BOR is off when in Sleep
• BOR is controlled by software
• BOR is always off
Oscillator Unit
 A microprocessor/Microcontroller is a digital device made up of
digital combinational and sequential circuits.
 The instruction execution of a microprocessor/controller occurs
in sync with a clock signal.
 Oscillator unit is responsible for generating the precise clock for
the processor.
 Certain processors/controllers integrate a built-in oscillator unit
and simply require an external ceramic resonator/quartz crystal
for producing necessary clock signals.
 The speed of the operation of a processor is primarily dependent
on the clock frequency. The total system power consumption is
directly propotional to the clock frequency.
Real time clock
 Real-time clocks (RTC) are timers dedicated to maintaining a
one-second time base. In addition, an RTC is often used to keep
track of clock time and calendar date either in software or
hardware.
 Many of the features of an RTC are very specialized and required
for maintaining high accuracy and very reliable operation. There
are RTC devices external to a microcontroller which interface
with an I2C or SPI bus.
Watch dog Timer
• External watchdog timers are integrated circuits that physically assert
the reset pin of the processor.
• The Processor must assert an output pin in some fashion to reset the
timing mechanism of the watchdog.
• This type of watchdog is generally considered the most appropriate
because of the complete independence of the watchdog from the
processor.
• Some external watchdogs feature a windowed reset.
• Enforces timing constraints for a proper watchdog reset.
• Minimizes the likelihood of errant software resetting the watchdog.
Embedded Firmware Design Approaches
THANK YOU

You might also like