Scribd
Upload
458 views11 pages

4G DL Power Allocation in Huawei

The document discusses LTE downlink power allocation. It explains that the eNodeB allocates different power levels for different downlink channels. The reference signal power and synchronization channel powers influence cell coverage. Power for other channels like PDCCH is set using offsets from the reference signal power. The goal is to maintain a constant energy per resource element. The document provides examples of how adjusting parameters like reference signal power, PDSCH type A power, and PDSCH type B power can optimize power utilization or maintain coverage depending on scenarios. It recommends settings to maximize power utilization at the RRU.

Uploaded by

brr.rezvani
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PPTX, PDF, TXT or read online on Scribd
458 views11 pages

4G DL Power Allocation in Huawei

The document discusses LTE downlink power allocation. It explains that the eNodeB allocates different power levels for different downlink channels. The reference signal power and synchronization channel powers influence cell coverage. Power for other channels like PDCCH is set using offsets from the reference signal power. The goal is to maintain a constant energy per resource element. The document provides examples of how adjusting parameters like reference signal power, PDSCH type A power, and PDSCH type B power can optimize power utilization or maintain coverage depending on scenarios. It recommends settings to maximize power utilization at the RRU.

Uploaded by

brr.rezvani
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PPTX, PDF, TXT or read online on Scribd
You are on page 1/ 11

DL Power allocation

Behzad Rezvani
LTE DL Power allocation

 In downlink, ENB allocates different power level for different DL channels

 The RS power and the SCH powers are key parameters that influences the cell coverage.

 Power of PDCCHs, PHICHs, PCFICHs, PBCHs, primary and Secondary synchronization channels
is set using an offset from RS power

 Tha goal is to maintain a constant energy pre resource elements


LTE DL Power allocation

ODFM symbols in one time slot can be classified into 2 types:

 PDSCH type A :
REs are not in the same symbols as reference signal REs are

 PDSCH type B :
REs in the same symbols as reference signal REs
LTE DL Power allocation

Default is zero

ρ A = PA
PA =PapCoff ~ Ericsson CRSgain
LTE DL Power allocation

PB = ρ B / ρ A Or ρ B = ρ A * PB
PB = PDSCH TYPE B Gain
LTE DL Power allocation 50% of
RRU
Bandwidth: 10 Mhz Bandwidth: 10 Mhz
RB: 50 RB: 50
power
Antenna Ports: 2 Antenna Ports: 2 wasted
PA: -3 PA: -3
PB: 1 PB: 1
RS_Power: 18.2 dBm : 66.66 mWatt RS_Power: 15.2 dBm :33.32 mWatt
Power Per Port: 20 Watt (Max TX Power) 3dB Rs de-boost Power Per Port: 10 Watt (Max TX Power)
LTE DL Power allocation
Bandwidth: 10 Mhz Bandwidth: 10 Mhz
Power
RB: 50 RB: 50 maintained
Antenna Ports: 2 Antenna Ports: 2
PA: -3 PA: 0
PB: 1 PB: 0
RS_Power: 18.2 dBm : 66.66 mWatt 3dB Rs de-boost RS_Power: 15.2 dBm :33.32 mWatt
Power Per Port: 20 Watt (Max TX Power) Power Per Port: 20 Watt (Max TX Power)
PA and PB changes
LTE DL Power allocation
Bandwidth: 10 Mhz Bandwidth: 10 Mhz
RB: 50 RB: 50 Avail power
Antenna Ports: 2 Antenna Ports: 2
PA: 0 PA: 0
exceeded !!!
PB: 0 PB: 0
RS_Power: 15.2 dBm ~ 33 mWatt 3dB Rs boost RS_Power: 18.2 dBm :66 mWatt
Power Per Port: 20 Watt (Max TX Power) Power Per Port: 40 Watt (Max TX Power)
LTE DL Power allocation
Bandwidth: 10 Mhz Bandwidth: 10 Mhz Power
RB: 50 RB: 50
Antenna Ports: 2 Antenna Ports: 2 maintained
PA: 0 PA: -3
PB: 0 3dB Rs boost PB: 1
RS_Power: 15.2 dBm ~ 33 mWatt PA changes RS_Power: 18.2 dBm :66 mWatt
Power Per Port: 20 Watt (Max TX Power) Power Per Port: 20 Watt (Max TX Power)
LTE DL Power allocation

RS Power calculations :
5 MHz (25 RB), 10 MHz (50 RB), 15 MHz (75 RB), 20 MHz (100 RB)

sd
LTE DL Power allocation

Since RS power, PA, PB are parameters to be set there is a possibility of wasting some of RRU power

Below is recommended setting is to have maximum utilization

You might also like