Principles of the selection of Base Station Antennas
Technical Intercommunication
Haitian Institute March,2002
Functions of Antennas
What is an antenna?
l l
emit to the space the electric signal from the conducting line. receive radio waves and effect electric signals.
Blah blah blah bl ah
The function of Antennas
Transfer HF electromagnetic energy in the transmission line into radio waves in the free space, or vice versa. Hence, the knowledge of radio waves and HF transmission lines is a prerequisite to the study of antennas.
Basic Principles of Radio Waves
A conducting line radiates radio waves when AC circuit flows through it. The efficiency of the radiation depends upon the length and the shape of the conducting line. Two conducting lines positioned closely, the induced electromotive forces will almost be neutralized, hence radiating little energy. If the two conducting lines, with the currents in the same direction, are positioned apart,the induced electromotive forces will strengthen each other, hence radiating more energy. When the length of the conductor is far less than the wavelength and the current is small, the resulting radiation will be very weak. When the length of the conducting lines is comparable to the wavelength, the current through the lines will be greatly enhanced, hence resulting strong radiation. Generally speaking, the conducting lines radiating remarkable energy is called radiators.
Antennas can be seen as four-port network.
Four-port Network
RF Cable
Free Space
Symmetrical transference
Coaxial Cable
Antenna
Coaxial cables are converted into antennas.
coaxial cable
transmitter
electric field
transmitter electric field
wavelength
transmitter
electric field
Dipoles
Radiators with two arms of the same size are called dipoles. The length of each arm
is a quarter of the wavelength. Dipoles with their length the same as the wavelength is called full-wavelength dipoles. Dipoles with their arms folded are named folded dipoles. wavelength wavelength
wavelength
wavelength wavelength radiator
At 800MHz, a wavelength dipole is approximately 200mm. At 400MHz, a wavelength dipole is approximately 400mm.
Operating Frequency range (bandwidth) of antennas
Antennas, receiving or transmitting, work within a certain range of frequencies (or within a certain bandwidth). Generally, working at the central frequency, antennas result the most power. Deviating from the central frequency, the antenna will produce less power. Based on these discussions,the following definitions of operating frequency range (bandwidth) of antennas are given: Def.1 Bandwidth refers to the bandwidth when the gain of the antenna drops by 3 dBi; Def.2 Bandwidth refers to the working bandwidth of the antenna when the VSWR is specified. In mobile communication, Def.2 is adopted, namely, bandwidth refers to the working bandwidth when VSWR1.5.
Field Distribution of Half-wavelength Radiator
voltage distribution
current distribution
electric field distribution
magnetic field distribution
Operating beyond the optimal wavelength, the antenna will suffer in performance. Operating within the operating frequency band, the antenna works somehow acceptably with little sufferance in performance.
Optimal performance at the frequency of 850MHz.
820 MHz
890 MHz
waveleng th element
Half-wavelength is 180mm at 820MHZ; half-wavelength is 170 mm at 890MHZ. The antenna get an optimal performance at 850MHz with half-wavelength 175mm. The bandwidth of the antenna is 890 - 820,hence 70MHz.
Radio Waves
What are radio waves? Radio wave is a way of energy propagation, in the process of which the electric field is perpendicular to the magnetic field while both are perpendicular to the direction of propagation.
Radio Waves
Similar to the wave in the pond, radio waves weaken during propagation. The same as light, radio waves propagate at speeds subject to the propagation media. In vacuum, the propagation speed equals that of light, which can be represented as c = 300,000km/s. In other media, the propagation speed VC/in which is the relative dielectric constant of the media. The relative dielectric constant of the air, a little more than 1, is approximately equal to that of vacuum. Therefore, the propagation speed of radio waves in the air is generally taken as that of the light.
The Propagation of Electromagnetic Wave
Magnetic
Magnetic
field
field
Electric field
Electric field
Electric field
Direction of radio wave
propagation
The Relationship Between Wavelength, Frequency and Speed
Their relationship can be represented by the formula /,
in which V stands for speed, in m/s; f for frequency, in Hz; for
wavelength, in meter. From the above formula, it is clear that radio waves of the same frequency propagate at different speeds in different medias. The Teflon isolation coaxial RF cable, as are often used, has a relative dielectric constant2.1. Therefore,/1.44
wavelength
/1.44.
Polarization of Radio Waves
During the propagation, the direction of the electric field of radio waves will vary with regularity, a phenomenon called the polarization of radio waves. The electric field of the waves is defined as the the direction of polarization. If the electric field is perpendicular to the ground, the radio wave is defined as vertical polarized. If this electric field is parallel to the ground, the radio wave is said to be horizontal polarized.
The polarization of antennas
The direction of the electric field of the electromagnetic field effected by antennas is defined as the polarization of the antennas.
V-Polarization H-Polarization
H-Polarization H-Polarization
- 45Polarization
+ 45Polarization
Circular Polarization
If the direction of electric field of the wave circulates during propagation, the radio wave is defined as ellipsoidal polarized wave. If the amplitude of the electric field remains constant during propagation, the radio wave is circular polarized. If the electric field, seen along the propagation direction, circulates clockwise, the wave is said to be rightcircular-polarized, on the contrary, left-circular-polarized. V-polarized waves must be received by V-polarized receiving antennas, and the same holds true for right-circular-polarized and leftcircular-polarized . If the polarization direction of the radio wave is different from that of the receiving antenna, polarization loss results. For example,the circular-linear case will result in 3dB polarization loss, that is, if the circular polarized antenna is adopted to receive linear polarized waves,3dB energy will be lost; the same goes for linear- circular case.
1.Duel Polarized antennas
Two antennas is integrated, effecting two waves independent of each other.
V/H Dual polarization
Cross (+/- 45) Dual polarization
Polarization Loss
If the polarization direction of the radio wave is
different from that of the receiving antenna, polarization
loss results. For instance,the linear-circular loss is 3dB, namely, half the energy is lost. If the polarization direction of the radio wave is perpendicular to that of the receiving antenna ( such as the case of the left and right circular working together) , results no energy received. Such case is defined as isolation of polarization.
Polarization) Isolation
Isolation refers to the proportion of the signal fed to one polarization to that appearing in another polarization.
The polarization loss in this case;
10log(1000mW/1mW) = 30dB
1000mW or 1W
1mW
The Directivity of the Antenna
Directivity is defined as the ability of an antenna to
radiate electromagnetic waves in a certain direction. In the case of a receiving antenna, directivity refers to the ability of the antenna to receive signals from different directions. The directional feature of an antenna is often shown in the radiation pattern of the antenna.
The radiation pattern indicates the ability of an antenna
to receive or transmit signal in different directions.
Radiation Pattern
A single element effects the pattern of a bread ring. Top view Side view
In order to direct the signal to the destination close to the surface of the earth, the bread ring is required to be pressed flat.
Symmetrical element array radiates energy in a flat bread ring
1symmetrical element 1mw received power
4 pairs of symmetrical elements 1mw received power
Gain in this case: 10log(4mW/1mW) = 6dBd
More centralized signal
Principles of Directional Radiation
The array and reflecting boards, on the one side of the array,
constitute a sector coverage antenna.
antenna
(top view)
Omni-directional array 4mW received power
Sector coverage 8mW received power
In the sector coverage antenna, the reflecting board focuses the energy in one direction, hence enhancing the gain. In this case, the gain of a sector antenna over that of an omnidirectional antenna is 9dBd.
Front-to-back Ratio
Front-to-back ratio is the ratio of the maximum power of the front beam to that of the back beam. The higher the front-to-back ratio, the better the performance of the antenna in directional reception. The front-to-back ratio of an omni-directional antenna is 1, receiving signals from all direction with the same sensitivity.
Back radiated power
Front radiated power
front-to-back ratio in dB= 10log front radiated power/back radiated power; The typical value is 25dB, so as to minimize the back radiated power.
Beam Width
In radiation patterns, there are two or more beams, the biggest of which is called the main beam, the rest, side beam. The angle between the two halfpower points of the main beam is defined as the beam width, or half-power angle. The narrower the beam width, the better the directionality and the resistance to interference.
Diagram of side lobe
Up side lobe suppression
Down side lobe suppression
Gain of Antenna
11. The definition of gain
Gain is defined as the ratio of the square of the field intensity effected by a certain antenna and that by an ideal radiating unit, with the input power given. Gain generally has to do with the radiation pattern of the antenna, that is, the narrower the main beam, and the smaller the back beam and side beam, the higher the gain.
The Gain and The Vertical Beam Width of An Omni-directional Antenna
Half power beam width
With /2 as reference
9dBd Omni-directional Antenna
Radiation pattern
horizontal
vertical
The Gain and Horizontal Beam Width of an Panel Antenna
Half
/2 element
power
beam
Gain with /2 element as reference 0dBd
width
360
/2
element
with
reflector 180 3dBd
Two
/2
elements
with
reflectors 90 6dBd
Pattern theroy
in
2. The difference of dBd and dBi
A single symmetrical element effects the radiation pattern in a bread ring. A symmetrical element is an omnidirectional radiator.
The gain of an antenna over that of a symmetrical element is represented in dBd; The gain of an antenna over that of an isotropic radiator is represented in dBi; hence, 3dBd=5.17dBi
2.17dB
The gain of a symmetrical element is 2.17dB.
The relationship of gain with beam width
In general, the narrower the beam width, the higher the gain.
In cases where the side beam level and the front-to-back ratio is normal,
the relationship between gain and radiation pattern can be represented as follows:
G(dBi) 10 log 32000 2 0.5E 2 0.5H
As for reflector antennas, with the radiation efficiency considered,
G(dBi) 10 log 27000 2 0.5E 2 0.5H
Gain
vertical
Horizontal Half Power Beam Width
On Transmission Line
Feeder cables or transmission lines are used to effectively transmit signals between the input/output ports in the emitter/receiver and the antenna. The transmission line should transmit the signal to the input port in the receiver /antenna with the lowest possible loss. Beside, they should transmit or generate no spurious signals. Hence the feeding line must be shielded or balanced. Transmission cables with lengths equal to or longer than the wavelength of the transmitted signal are called long transmission cables or simply long cables.
1. The input impedance of antennas
Input impedance is defined as the ratio of the induced signal voltage to the induced signal current at the point where the antenna is connected to the feeding cable. The input impedance consists of the electric resistor and electric impedance components. The electric impedance component reduces the power of the effective signal fed by the antenna into the cable. So, efforts are made at a zero of the electric impedance component, so that the input impedance will be pure electric resistor. The input impedance has to do with the structure of the antenna and the wavelength. The half wavelength radiators,symmetrically fed from the middle, have an input impedance of (73.1+j42.5) ohm. If the length of the elements is reduced by 3%~5%, the electric resistor component can be eliminated, hence the input impedance the pure resistor, 73.1 ohm, often labeled 75 ohm.
2. Characteristic Impedance of Feeding Cables
Characteristic impedance is defined as the ratio of the voltage to current at all points on a feeding cable of unlimited length. The impedance is often represented by Z. For coaxial cables, 138/r log(D/d)ohm. Usually, =50/ 75 ohms. In the formula, D stands for the outer diameter of the copper net, d, inside diameter of the conductor, and r dielectric constant of the isolation medium between the conductor lines. From the above formula, it is clear that impedance is connected with the diameters of conductors, distance between the conductors and the dielectric constant of the isolation medium, while having nothing to do with the length of the cable, working frequency and the load.
3.Reflection Ratio, VSWR, Return Loss
In the case of matching between the feeder cable and the antenna, the highfrequency energy will be completely absorbed by the load, when exists only input waves in the cable. In this case, traveling waves is transmitted along the feeder cable, the amplitude of the voltage is the same at every point, and impedance at every point equals its characteristic impedance. In the case of mismatching, that is, when the impedance of the antenna is not the same as the characteristic impedance of the cable, not all the fed signal can be absorbed by the load. Part of the input wave will be reflected as reflected wave.
forward: 10W 50 ohms backward: 0.5W
80 ohms
9.5 W
In the above case, the reflection loss is 10log(10/0.5)dB reflection loss.
VSWR is another representation of
In the case of mismatching, input wave and reflected wave co-exists in the cable. The two waves combine to effect wave loop where the magnitude reaches the maximum, wave node where the magnitude is the minimum and other points where the magnitude falls between the loop and the node. The combination of the two waves is called static wave. The ratio of the magnitude of the reflected wave to the input wave is called reflection ratio. Reflection ratio = mag of reflected wave /mag of input wave =(Z-Z)/(Z+Z) The ratio of the wave loop voltage to the wave node voltage is said to be static wave ratio, or voltage static wave ratio. (VSWR)Static Wave Ratio= = Vmax(max value of the mag of wave loop voltage) Vmin(min value of the mag of wave node voltage) =(1+)/(1-) =(1+)/(1-) The closer the load impedance value to that of the characteristic, the smaller the .reflection ratio,and the more closer to unit the VSWR, the better the match.
VSWR,Reflection loss and Reflection ratio
antenna Input wave Reflected wave
Reflection loss
Reflection ratio
Coaxial cable
transmitter
Reflection attenuation
Reflection ration
Specification of a Typical GSM BTS Antenna
l l l l l l l Frequency range :MHz 820 890 Band width: MHz 70 Gain dBi: 15 Polarization: Vertical Impedance 50 Reflection loss dB >18 Front-to-back ratio dB >30 Half-power beamwidth (3dB) H: 64 V: 18 10dB beamwidth H: 120 V: 30 Ssuppression of upper lobe: dB< -12 Suppression of lower lobe: dB < - 14
l Tilt(adjustable) 2 - 10
Cable System for BTS Antennas
mechanical tilt installation kit Installation pole 50~114mm Connector sealing kit GSM/CDMA Panel antenna
Grounding device
Main 7/8
feeder In-door soft jump cable
protecting
Out-door cable Cable support
Feeder clamp Wall-entry
Lighting kit
BTSequipment
Cable System for BTS Antennas
1. Mechanical tilt installation kits It is adopted to adjust the tilt angle, ranging from 0to 15 . 2. Out-door jumper cable Applied between the antenna and the 7/8main feeder cable, usually 1/2 , 3m long. 3. Connector sealing kits These kits are used for the sealing of the connectors on the out-door jumper cable. Usually these kits are 3M2228 isolation water-proof tape or PVC(3M33+) isolation tape. 4. Grounding kit7/8feeder cable grounding kit These kits are used for lighting protection. They are connected to the outer conductor of the main cable. Usually 3 such kits are adopted respectively at the upper, middle, and lower points of a cable. The grounding direction must be in line with that of the current.
Cable System for BTS Antennas
5. 7/8Cable clamp These kits are intended for the fixing of the cable to the tower or to the wall. In the vertical direction, one for every 1.5m; in the horizontal direction, one for every 1m. (Inside the chamber, no clamps are needed because the Nylon tape will be good enough). 7/8clamps in common use: Twin or triple, to fix 2 or 3 cables. 6. Cable Support It will supply a route for the main feeder, power cable, transmission cable and the clamp. 7. Wall Entry Let in the cables while keeping out rain, birds, rats and dust. 8. Lightning protection(Lightning Arrestor) Installed between the main feeder and the indoor jumper cable ,this device is intended for lightning protection and spurt current leakage. Its grounding line goes out of the wall-entry to the tower or to the ground directly.
Cable System for BTS Antennas
9. Indoor soft jumper cable This cable connects the lightning arrestor to the main equipment of the BTS, usually 1/2 soft cable, 2~3 meter long. As interfaces and the position of interfaces vary with the main equipments of the BTS in different companies, the indoor soft jumper cable and the connectors vary in specification. The connectors on the indoor soft jumper cable can be 7/16 DIN, N, straight or curved. 10. Nylon tape(black) It functions as in the following: (1) In installing the main feeder, it is used to fix the cable. After the clamps are used, the tape can be removed. (2) At the corner of the main feeder, a clamp can not be used. At this point, the nylon tape is a must. 11. Nylon tape(white) This is to fix the indoor jumper cable and the indoor part of the main feeder.
The propagation of ultra-short waves
Radio waves of different wavelengths demonstrate different propagation features. The GSM and CDMA frequencies fall into the UHF (Ultra-high frequency) band, with their high end included in the microwave band. 2.1 The line-of-sight propagation of ultra-short wave and microwave Ultra-short wave and microwave attenuate quickly along the ground due o their high frequency and short wavelength. So, rather than along the globe, these waves propagate in the space. In space, the wave propagates along a direct line to points within the sight. The propagation area of ultra-short wave within the sight is often called illuminated area, within which receiving instruments can receive stable signals.
The line-of-sight propagation distance has to do with the heights of the receiving and transmitting antennas and the curvature radius as the formula indicates: AB3.57(HT+HR)(km) With the refractive effect of the air considered, we define the effective line-of-sight as: AB=4.12 (HT+HR)(km)
A Height of receiving antenna HT RT O' RR B Height transmitting antenna HR of
Multi-path propagation
Besides direct propagation, radio waves are also reflected by barriers such as hills, forests, buildings and the ground. So, the receiving antenna receives not only propagation waves, but also reflected waves. This effect is called multi-path propagation. Multi-path propagation causes the complexity in field intensity distribution, serious fluctuation in amplitude and change in the polarization of radio waves. As a result, the signal field intensity varies with places, some strengthened, some weakened. Also, different barriers reflects radio waves differently, for example, concrete buildings reflect more radio wave than brick buildings do. Efforts should be paid to eliminate the multi-path propagation effect.The solution to this problem can be the technologies of space diversity and polarization diversity.
1. Multi-path propagation and reflection
2.the improvement of signal electric level by diversity
Electrical level
distance
Diffraction propagation of radio waves
Radio waves tend to diffract around a barrier during propagation. This phenomenon is called the diffraction propagation of radio waves. The weak ability of ultra-short wave in diffraction results in the shadow behind big buildings. The extent to which the signal is affected has to do with the distance between the antenna and the building, and frequency as well.For example,the received signal will not be affected at the points 200m apart from the building of 10m height. But the signal will be weakened at the points 100m apart from the signal. In this case, the field intensity of the received TV signal at the frequency of 216-223GHz is 16dB weaker than in the place where no high buildings stand. In the case of 670GHz signal, the reduction is 20dB. When the height of the building is increased to 50m, the field intensity will be affected within 1000m apart from the building. The higher the frequency and the building, and the more closer to the building, the greater the effect, vise versa. So, in selecting the antenna installation site, the above factors should be considered so as to avoid the negative effects as much as possible.
Antennas in network optimization
1. The application of antenna parameters to the system planning for mobile communication. 1) Radiation pattern (1) horizontal pattern has to do with beam width and coverage area.
(2) the beam width in vertical pattern determines the power distribution over coverage.
2)Communication Distance Formula
PT(dB)=PR(dB)+20log4R(m)/min(m)-GT(dBi)-GR(dBi)-Lc(dB)-L0(dB) In the equation, Lc stands for the loss of the feeder cable for BTS antennas; L0 the wave loss during propagation. In system designing, a margin should be reserved for L0. In general, wave propagation loss has a bearing on the environmental condition during propagation. For example, radio waves suffer a loss of 1015dB, upon penetrating civil construction or trees; 25-30dB in the case of concrete walls. As for mobile phones in CDMA /GSM of 800MHz or 900MHz, it is generally believed that the receiving threshold is 1.4dBm. But actually, the received signal should be 10dB higher than this value, so that the received signal can reach the standard in signal-to-noise ratio. As a matter of face,receiving power is taken as 170dBm in calculating, so as to guarantee good telecommunication.
A BTS is supposed to features the following constants: Transmitting power PR=-70dBm Receiving power PT=20w=43dBm Cable loss Lc=2.4dB(60 The gain of the receiving antenna Gr=1.5dBi Operating wave length =33.333cm(f0=900MHz) 43dBm-(-70dBm)+GT+1.5dBm=32dB+20logR(m)+2.4dB+L0 Substituting the above values yields 80.1dB +GT (dBi )=20logR(m)+ L0 It is believed that good communication can be maintained when GT (dBi )>20logR(m) -80.1dB + L0.
If the BTS adopt omni-directional antenna of GT 11dBi, good communication will be ensured within 1km when L0 <31.1dB. With L0 the same value as mentioned above, the communication distance can be doubled,that is,R=2km, if GT is increased by 6dBi. If GT remains 11db and L0 is reduced by20dB, R can be increased by ten times,that is,R=10km. Closely related with environmental condition, propagation loss is high in urban cities densely covered with high building while it is low in countryside thinly scattered with low house. Therefore, configuration in communication system the same, different environmental condition effects different coverage, hence different communication performance. So, it is a must to select the BTS antennas according to application environmental condition.
18o
.
40m
S
S
In the case of vertical beam shown in the diagram, GT in the above calculation refers to the value on the main axis. Usually installed on the tower, the BTS antenna should be titled to guarantee enough power coverage for the receiver. The title angle is determined by the height of tower and the distance between the user and the antenna
As seen in the above vertical pattern, shadow under the tower will result if the receiver happens to stand in the null-coverage of the beam. To combat this problem,null-fill antenna can be adopted. The alternative solution is to downtilt the beam. 2. Antennas in network optimization 1) the definition of network optimization It refers to the proper adjustment of regulation and design of the communication network according to certain guidance so as to ensure reliability and cost efficiency of the network. It aims at better operation quality and high utilization ratio of radio resources, all of which is essential for both mobile user and operator.
Suggestions E800 on quality of network operation (ITU-T) divides the network quality into six items as follows:
network quality
network guarantee ability
network utilization ability
Network access ability
Network maintaining ability
Network perfecting ability
Network safety ability
Service ability
Of these six ,three items has a bearing on network optimization: (1) Access ability refers to the ability to put through the call when the capacity and other conditions given. In mobile communication it is has to do with call loss. (2) Network maintaining ability is the ability to hold communication in a given time and on certain condition after the call is put through. It has a bearing on call drop . (3) Network perfection ability is the ability to guarantee speech quality and avoid interference during the communicating.
2. Main content of network optimization
Based upon the above discussions, we can summarize the network optimization having the following content: (1)Efforts should be made to realize 90% of seamless coverage, non shadow area,and min receiving electric level in the radiation area. (2) Rationalize the configuration of ratio resources, increase frequency reutilization ratio, and expand network capacity. (3)Reduce interference and call-drop rate,and increase callcompleting ratio. All these have to do with the proper selection and adjustment of BTS antenna parameters.
The function of antennas in network optimization
1) To realize seamless coverage, the proper selection of BTS antenna parameters is of essential importance.As for GSM or CDMA BTS for digital mobile communication network, the selection of BTS antennas available at home is based upon the following principle: Tilt angle can be reached by the following formula: arch/ r/2 (in which stands for tilt angle;h height of antenna, r the distance between base stations.
(a)
(b)
(c)
In high-volume areas, the distance between stations is 300-500m, and the title angle should be 10-19o. To satisfy these needs, we suggest a 45dual polarized directional antenna with inbuilt 9o electrical downtilt and 65obeam width. Working with mechanical downtilt mounting kits of 15o, the antenna secure that the pattern in horizontal directional remain constant when the main beam tilts 10-19o. The wide application of the antenna indicates that it can satisfy coverage need in high density urban areas . In medium-volume urban areas,the distance between stations is bigger than 500m and downtilt angle should be 6-16o. In this case, 45dual polarizeddirectional antenna with inbuilt 6o electrical downtilt and 65obeam width can secure consistent half power beam width when the main beam tilts 6-16o ,and satisfy coverage need in medium density urban areas . In low-volume urban areas, the distance between stations are large and the tilt angle should be 3-15.
In this case, 45dual polarized directional antenna with inbuilt 3o electrical downtilt and 65obeam width can secure consistent half power beam width when the main beam tilts 3-15o ,and satisfy coverage need in low density urban areas . 2) Antenna selection for small town areas: In these low volume areas, the main consideration should be paid to coverage need,hence large distance between stations feasible. In this case, we can select single polarized antennas(triple or dual section) featured by higher gains(17dBi) and larger horizontal beam width(65,90).
3) Antenna selection for the countryside In these low volume areas, coverage need is the first consideration. So a good choice is omni-directional high gain antennas(HTQ-09-11) with 3,5,7 tilt angle. 4) Antenna selection for highways/railroads and nearby towns (1) Dual section (180for each) . This design features 90half power beamwidth and high gain(17-18dBi) antennas and back-to-back installation with the largest radiating directed along highway. Their resultant radiation pattern is shown in the below diagram.
(2) High-way dual-directional antenna. If the volume is rather small along highway/railway, we can select dual polarized antennas(HTSX-0914),a modification of omni-directional antenna, featured by 70beamwidth and 14dBi gain. Its pattern is shown as follows.
Railway and highway
(4) Highway&town antennas:In the low-volume areas where both
highway/railway and nearby town should be covered, weak directional
antenna HTD0921013 is used to satisfy the coverage need.
Highway;railway
town
Highway;railway
(5) radiation-controlled pattern
(1)
Horizontal beam High front-to-back ratio Side lobe suppression across frequency band Remain constant 10dB beamwidth of horizontal beam during the adjustment of tilt angle. (2) vertical beam Side lobe suppression across frequency band Null fill feature Consistent gain across frequency band. Dual polarized antennas should feature enough isolation and space polarization discrimination. 6) Increase carrier-to-signal ratio by the adjustment of BTS antennas. 7) Improve the speech quality in coverage area , balance the network load, and improve network operating efficiency by the adjustment of BTS antennas elevation angle.
Lower-side-lobe will effect fewer interference. Lower-side-lobe null-fill can improve tower coverage. Beam with lower up-side lobe
Interference from nearby cellular unit.
Mobile pone signal in cellular unit
What has been discussed is part of the problems related with antennas in network optimization. From these discussion , it is clear that the antenna accounts for 50-60% of work amount in network optimization and maintenance, though it only entail 1-2% of expense in network planning. So,it is safe to claim: no good antenna, no good radio network and high quality mobile communication service.
Instruction to some XAHT antennas for network optimization
1. Remote control electric downtilt antenna In network optimization, elevation angle needs constant adjustment. The adjustment method available is as follows: (1) mechanical tilt (2) Electrical tilt
Adjustment of antennas in network adjustment of tilt angle
Antennas are tilted to direct the beam to the ground.
No tilt
Electrical tilt
Mechanical tilt
Beam down tilt
Intended for: coverage control reduction of IM Two methods Mechanical Electrical
Beam coverage in the case of electrical tilt
No tilt
Electrical tilt
Beam coverage in the case of mechanical down tilt
No tilt
Mechanical tilt
Comparison between two methods
10electrical down tilt
6electrical down tilt +4mechanical tilt
10mechanical tilt
How to realize adjustable electrical downtilt
the realization of electrical down tilt
No tilt Feeding lines of the same length
Tilt Feeding lines of different length
(1) (2) (3) (4)
From the above discussions, it is clear that problems exist with mechanical down tilt antennas in network optimization, and electrical down tilt antennas are superior to mechanical tilt ones in performance. So HAXT has go further to develop and manufacture remote control electric downtilt antennas, featured by the following aspects: 2-13 continuous tilt adjustment( superior to foreign specification) The variation of gain is only 0.5dB during the adjustment of tilt angle.(superior to foreign specification) Down side lobe null fill( superior to foreign specification) Reliability of antennas is secured.(superior to foreign specification)
deg
deg
deg
deg
deg
deg
deg
deg
deg
deg
deg
13deg
IM 3rd order
Definition of IM IM refers to the noise in non-linear RF circuits, generated by mixing two or more signals at different frequencies. IM will result in non-existent error signal,which the system will mistake as real signal. Active devices(radio equipment,diode) or passive devices(cables,connectors,antennas,or filter) are responsible for the IM generation. Examples of IM distortion frequency of two carriers Carries at frequency A and B respectively will generate the following IM signal: First order AB Second order A+BA-B Third order 2AB2B A Forth order 3AB3B A2A2B Fifth order 4AB4B A3A2B3B 2A How does IM distortion affect the performance of the system Transmitted signal with high power will, in most cases, generate IM signal, then received by the receiver. Received signal by BTS antennas is usually low in power. When the frequency of IM signal is close to or higher than that of the desired signal, the system will mistake the IM signal as the desired one.
Examples of GSM
IM distortion signal(A=935MHz,B=960MHz) 2A-B=1870-960=910MHz, 2B-A=1920-935=985MHz A and B represents transmitting frequency in GSM. Problems will result from the entrance of 2A-B into receiving band. 5th order IM distortion signal(A=935MHz,B=954MHz, within the frequency range of down link for China mobile GSM. 3A-2B=2850-1980=897MHz(within the frequency range of up link for China mobile GSM) How does IM affect the performance of the system? Mistaking IM signal as the received signal will entail the following problems: Signal loss, false channel busy, downgrade of speech quality, limitation of the capacity. Profit suffers Though they may tolerate the downgrade of speech quality, mobile users will dissatisfy with signal loss and channel busy. How is IM generated? Component materials Iron materials are nonlinear, due to hysteresis. Materials are not pure. Galvanization Contact area/current density Pressure at the contact
Antennas for 3G mobile communication Smart antennas
1. 1) Antennas: devices specified for receiving electromagnetic signals. omni-directional
0
120
E Horizontal
vertical
0.0 0.2 0.4 0.6 0.8 240 1.0 0
0.0 0.2 0.4 0.6 0.8 1.0
0.0 0.2 0.4 0.6 0.8 1.0
vertical
0.0 0.2 0.4 0.6 0.8 1.0 0
Horizontal H
2) Directional
0
0
E
0.0 0.2
0.0 0.2 0.4 0.6 0.8 1.0 90
H
90 0.4 0.6 0.8 1.0
3)multi-beam
0 0.0 0.2 0.4 0.6 0.8 1.0 90
120
60
0.0 0.2 0.4 0.6 0.8 1.0
2.Smart antennas
1) 2) 3) 4) It can effect more than one narrow beams. Each beam can automatically track each user. It can automatically reject interference. Beams are independent of and perpendicular to each other. Antennas with these functions are called smart antennas(Spectrum Management through Antenna in Radio Technology). The spectrum management here does not refer to the management of frequency spectrum but that of space spectrum,or the management of azimuth angle of the coming signal.
x1= s0 ejt x2=s0 ej(t-) =dsin/c x3=s0 ej(t-2) x4=s0 ej(t-3) c=f xi=s0ej(t-(i-1)) = s0ejt e-j(i-1) = s0ejte-j2d/(i-1)sin= s0ej2ft e-j2f (i-1) f = dsin/ f stands for space frequency. Its relationship with phase is as follows: I=2 (I-1)f As for the time region signal: =2 ft It is the function of time sampling points. As for array signals, it can be seen as the sampling signal of azimuth angle . Sequential signals operate to filter frequency spectrum,that is,strengthening signals at certain frequencies while depressing the others. The array signals will filter the space spectrum,that is, strengthening the received signals of certain azimuth angle, while depressing the others.
Features of smart antennas
1. Smart antennas can make frequency resources to their advantage. 1) Urgent problems to be solved in mobile communication. (1)number of mobile users is soaring. (2)service content is to be richer. 2)solutions (1) Exploit new frequency resource (2) Increase utilization ratio of the frequency resources available. 3) Cellular zoon is adopted to reutilize space frequency. TD,CD and FD are all possible measures to increase frequency utilization ratio. And SD technology is another measure available now. (1) SD supply one beam for each carries frequency in FEMA system. (2) SD provides each time gap with one beam in TDMA system. (3) SD supply one beam for each code in CDMA system. It is estimated that SD technology can expand network capacity by 4-6 time.
2. Improve communication signal, and reduce the cost of mobile communication system. (1) Increase signal-to-interference ratio, and improve communication. (2) Reduce transmitting and receiving power. (3) Decrease the number of BTS for terminal service. Based upon these consideration, the international telecommunication association has select SD as choice technology in the standard of 3G mobile communication. Classification of smart antennas 1. Switched smart antenna The original 120beam is replaced by four 30beams. These four beams can be switched to one another.
Antenna array
T T T T T T
Switch matrix
Base station
Control system
Smart antenna
Antenna array
T T T T T T
Beam-forming network
Adaptive arithmetic control
Signal processing
Research status quo at home and abroad
1. Smart antennas are paid much attention since 90s. And switched smart antennas has been put into market. 2. Adaptive antennas are under development.
Thanks May every one be healthy and happy!
You are welcomed to visit and supervise
our company!