Scribd
Upload
71 views

09 Numerical Methods

This document discusses numerical methods for solving multi-degree of freedom mechanical systems. It describes Rayleigh's method, Dunkerley's method, and the Rayleigh-Ritz method for approximating the natural frequencies and mode shapes of vibrating systems. The matrix iteration method uses flexibility matrices in the equations of motion to determine the lowest natural frequency and mode shape. Examples are provided to demonstrate applying Rayleigh's and Dunkerley's method to problems.

Uploaded by

Saroz Parajuli
Copyright
© © All Rights Reserved
Available Formats
Download as PPTX, PDF, TXT or read online on Scribd
71 views

09 Numerical Methods

This document discusses numerical methods for solving multi-degree of freedom mechanical systems. It describes Rayleigh's method, Dunkerley's method, and the Rayleigh-Ritz method for approximating the natural frequencies and mode shapes of vibrating systems. The matrix iteration method uses flexibility matrices in the equations of motion to determine the lowest natural frequency and mode shape. Examples are provided to demonstrate applying Rayleigh's and Dunkerley's method to problems.

Uploaded by

Saroz Parajuli
Copyright
© © All Rights Reserved
Available Formats
Download as PPTX, PDF, TXT or read online on Scribd
You are on page 1/ 8

THEORY OF MACHINES AND

MECHANISMS II
Mechanical IV/I
Chapter 9

Approximate Numerical
Methods
1
When the degrees of freedom of a system become large, the problem
of obtaining numerical results becomes difficult. It is necessary to
rely on the high-speed electronic computer for the solution.
Although the problem of finding the eigenvalues and eigenvectors of
a matrix equation is routinely handled by the electronic computer,
there are approximate and the other alternative procedures which are
often useful.

Some of the numerical methods used for solving multidegrees of


freedom system are
• Rayleigh method,
• Dunkerley method,
• Rayleigh-Ritz method,
• Matrix iteration method, etc.

THEORY OF MACHINES AND 2


MECHANISM II
9.1 Rayleigh's Method
This method developed by Rayleigh is very handy for finding the
fundamental frequency of a multi degree of freedom system. It is
based upon equating the maximum kinetic energy of the vibrating
system to the maximum potential energy.

For multi-degree of freedom system there are many masses and thus
many components of kinetic and potential energies, but all the masses
will have simple harmonic motions passing through their mean
position at the same instant, for any principal mode of vibration.

Good estimate of the fundamental frequency can be made by


assuming the suitable deflection curve according to the boundary
conditions. The maximum kinetic energy is then equated to the
maximum potential energy of the system to get determine the natural
frequency i.e.,
THEORY OF MACHINES AND 3
MECHANISM II
………. (1)

where Mi and yi are the mass and the deflection at point i.


9.2 Dunkerley's Method
Rayleigh's principle, which gives the upper bound to the
fundamental frequency, can now be complemented by Dunkerley's
formula, which results in a lower bound to the fundamental
frequency.

Dunkerley's equation can be written as


………. (2)

THEORY OF MACHINES AND 4


MECHANISM II
where n is the fundamental natural frequency of the system; 1, 2,
3, …. are the natural frequencies of the system with each mass
acting separately at its point of application in the absence of other
masses; and s is the natural frequency of the shaft alone due to its
distributed mass.

9.3 Rayleigh-Ritz Method


The Ritz method is essentially the Rayleigh method in which the
single shape function is replaced by a series of shape functions
multiplied by constant coefficients. The coefficients are adjusted by
minimizing the frequency with respect to each of the coefficients,
which results in n equations in 2. The solution of these equations
then gives the natural frequencies and mode shapes of the system.

THEORY OF MACHINES AND 5


MECHANISM II
9.4 Matrix Iteration Method
With the use of flexibility matrix in the differential equations, this
method is used when only the lowest eigenvalue and eigenvector of a
multidegree of freedom system are desired. The advantage of this
method is that the iterative process here results in the principal mode
of vibration of the system and the corresponding natural frequency.
The equation of motion in terms of flexibility matrix can be written
as
………. (3)

Using {x} = {X} sint the above equation results into


………. (4)
which may be written as
………. (5)
THEORY OF MACHINES AND 6
MECHANISM II
Example 9.1
Find the lower natural frequency of vibration for the system shown in
Figure E9.1 by
a) Rayleigh method
b) Dunkerley method. Take E = 1.96  1011N/m2, I = 4  10-7 m4.

354.94 rad/s, 348.8 rad/s


THEORY OF MACHINES AND 7
MECHANISM II
Example 9.2
For the system shown in Figure E9.2, determine the fundamental
natural frequency and corresponding mode shape.

THEORY OF MACHINES AND 8


MECHANISM II

You might also like