Addis Ababa Science & Technology University

College of Electrical and Mechanical

Engineering
Department of Electromechanical Engineering
Electrical Machines
By: Birhanemeskel A. (MSc in Mechatronics) 1
 Magnetics

Transformers

Induction Motors Course

Outlines
DC Machines

Synchronous Machines
2
 Chapter-One
Electro-magnetic circuits
 A magnet:- is a material which has the property of attracting small bits of
iron.

 Magnets are generally classified in two categories.

1. Permanent magnets

2. Electro-magnets

3
Permanent magnets
 It is the magnets which have the inherence property of retaining their
magnetism indefinitely and they require no electrical energy for retaining
their magnetism.

 A permanent magnet will position itself in a north and south direction when
freely suspended.

4
Electro-magnets
 It is the magnetization due to and only for flow of an electric current
through the coil.

 Electro-magnet are also sometimes called as Artificial Magnet.

 Magnetism and electricity are closely related.

 Whenever an electric current flows through a conductor, a magnetic field is

produced.

 Understanding magnetism is key to understanding motors, transformers,

relays, power transmission and generation 5
 The magnetic field produced in a conductor is relatively weak and is
proportional to the current moving through the conductor and the number
of turns wound on the materials.

 The higher the current flow, the stronger the magnetic field produced.

 The magnetic polarity is dependent on the direction of current flow.

6
Magnetic Field and its Significance
 The region around a magnet where its poles exhibit a force of attraction or
repulsion is called magnetic field.

 Michael Faraday suggested that the magnetic field could be represented

pictorially, by imagining the field to consist of lines of magnetic flux,
which enables investigation of the distribution and density of the field to be
carried out.

7
Properties of magnetic lines of force
 The direction of magnetic lines of flux radiates from North Pole to South
Pole outside the magnet and is from south to North Pole inside the magnet.

 Thus such lines of flux always form complete closed loops or paths; they
never intersect and always have a definite direction.

 The laws of magnetic attraction and repulsion can be demonstrated by using

two bar magnets. Unlike poles attract each other and like poles repel each
other. This is indicated in the fig below.

8
Properties of magnetic lines of force

9
Magnet circuit
 Magnet circuit is the path or the route followed by magnetic flux. In fact
the laws of magnetic circuit are almost similar to those of the electric
current circuit.
 Key Terms
 Magnetic flux (): The amount of magnetic lines of force set-up in a
magnetic circuit is called magnetic flux. Its unit is weber (Wb). It is
analogous to electric current I in electric circuit.

10
Key Terms
 The magnetic flux density at a point is the flux per unit area at right angles
to the flux at that point.
, its unit is

 Permeability: The ability of a material to conduct magnetic lines of force

through it is called the permeability of that material. The greater the
permeability of a material, the greater is its conductivity for the magnetic
lines of force and vice-versa. The permeability of air or vacuum is the
poorest and is represented as μ0 (where μ0 = )
11
Key Terms
 Relative permeability: The absolute (or actual) permeability μ of a
magnetic material is much greater than absolute permeability of air μ0. The
relative permeability of a magnetic material is given in comparison with air
or vacuum.

 Hence, the ratio of the permeability of material μ to the permeability of air

or vacuum μ0 is called the relative permeability μr of the material.

12
Key Terms
 Magnetomotive force (mmf): is the magnetic pressure which drives or tends
to drive magnetic flux through the magnet circuit and produced by passing
electric current through a wire of several number of turns.

 As per work law it may be defined as under: “The work done in moving a
unit magnetic pole (1 Wb) once round the magnetic circuit is called
magnetomotive force.”

Ampere-Turns (or AT)

 It is analogous to emf in an electric circuit.

13
Key Terms
 Magnetic field intensity: The force acting on a unit north pole (1 Wb) when
placed at a point in the magnetic field is called the magnetic intensity of the
field at that point. It is denoted by H. In magnetic circuits, it is defined as
mmf per unit length of the magnetic path.

 Reluctance (S): The opposition offered to the magnetic flux by a magnetic

circuit is called its reluctance.

14
Key Terms
 It depends upon length (l), area of cross-section (a) and permeability () of
the material that makes up the magnetic circuit. It is measured in AT/Wb.

15
Comparison between Electrical and Magnetic circuits

1 The closed path for magnetic flux is called The closed path for electric current is called
magnetic circuit electric circuit.
2 Flux = mmf/reluctance Current = emf/resistance
3 Flux, in Wb Current, I in ampere
4 mmf in AT emf in V
5 Resistance,
6 Permeability, μ Conductivity,
7 Flux density, , Current density,
8 Magnetic intensity, Electric intensity, E = V/d

16
Example 1:
1. An iron ring of 400 cm mean circumference is made from round iron of
cross-section 20 cm2. Its relative permeability is 500. If it is wound with
400 turns, what current would be required to produce a flux of 0·001 Wb?
2. A coil of insulated wire of 500 turns and of resistance 4Ω is closely wound on iron ring.
The ring has a mean diameter of 0·25 m and a uniform cross-sectional area of 700
mm2. Calculate the total flux in the ring when a DC supply of 6V is applied to the ends
of the winding. Assume a relative permeability of 550.

17
Series Magnetic Circuits
 A magnetic circuit that has a number of parts of different dimensions and
materials carrying the same magnetic field is called a series magnetic
circuit. Such as series magnetic circuit (composite circuit) is shown in Fig.

 Total reluctance of the magnetic circuit,

18
Series Magnetic Circuits
 Total magnetomotive force, mmf of the magnetic circuit,

++

19
Example 2
1. The ring shaped core shown in Fig. 1.16 is made of a material having a
relative permeability of 1000. The flux density in the smallest area of cross-
section is 2 T. If the current through the coil is not to exceed 1·5 A, compute
the number of turns of the coil.

20
Parallel Magnetic Circuits
 A magnetic circuit which has two or more paths for the magnetic flux is
called a parallel magnetic circuit. Its behavior can be just compared to a
parallel electric circuit.
 In the figure shown below, a current carrying coil is wound on the central limb AB. This
coil sets-up a magnetic flux in the central limb which is further divided into two paths
i.e., (i) path ADCB which carries flux and (ii) path AFEB which carries flux .

 It is known that

21
Parallel Magnetic Circuits
 The two magnetic paths ADCB and AFEB are in parallel. The ATs required for
this parallel circuit is equal to the ATs required for any one of the paths.

22
Leakage Flux
 The magnetic flux which does not follow the intended path
in a magnetic circuit is called leakage flux.
 When some current is passed through a solenoid, magnetic flux is produced
by it. Most of this flux is set-up in the magnetic core and passes through the
air gap (an intended path). This flux is known as useful flux .

 However, some of the flux is just set-up around the coil and is not utilized
for any work. This flux is called leakage flux .

23
Leakage Flux
 Total flux produced by the solenoid,

 The ratio of total flux () produced by the solenoid to the useful flux () set-up
in the air gap is known as leakage coefficient or leakage factor.

24
Magnetization or B-H curve
The graph plotted between flux density B and magnetizing force H of a
material is called the magnetization or B–H Curve of that material.

The shape of the B-H curve is non-linear, this indicates that the relative
permeability () of a magnetic material is not constant but it varies. The value
of largely depends upon the value of flux density. Its shape is shown in Fig.
below (for cast steel).

25
Magnetic Hysteresis
 When a magnetic material is magnetized first in one direction and then in the other
(i.e., one cycle of magnetization), it is found that flux density B in the material lags
behind the applied magnetizing force H. This phenomenon is known as magnetic
hysteresis.

 Hence, the phenomenon of flux density B lagging behind the magnetizing force H in a
magnetic material is called magnetic hysteresis.

 Consider a ring of magnetic material on which a solenoid is wound uniformly. The

solenoid in connected to a DC source through a double pole double throw reversible
switch (position ‘1’).
26
 When the field intensity H is increased gradually by increasing current in the solenoid
(by decreasing the value of R), the flux density B also increases until saturation point a is
reached and curve so obtained is oa. If now the magnetizing force is gradually reduced
to zero by decreasing current in the solenoid to zero. The flux density does not become
zero and the curve so obtained is ab. When magnetizing force H is zero, the flux density
still has value ob.

27
Residual Magnetism and Retentivity
 This value of flux density ‘ob’ retained by the magnetic material is called residual
magnetism and the power of retaining this residual magnetism is called retentivity of
the material.
 To demagnetize the magnetic ring, the magnetizing force H is reversed by reversing the
direction of flow of current in the solenoid. This is achieved by changing the position of
double pole, double throw switch (i.e., position ‘2’). When H is increased in reverse
direction, the flux density starts decreasing and becomes zero and curve follows the
path bc. Thus residual magnetism of the magnetic material is wiped off by applying
magnetizing force oc in opposite direction.

28
Coercive Force
 This value of magnetizing force oc required to wipe off the residual magnetism is called
coercive force. To complete the loop, the magnetizing force H is increased further in
reverse direction till saturation reaches (point ‘d’) and the curve follows the path cd.
 Again H is reduced to zero and the curve follows the path de. Where oe represents the
residual magnetism. Then H is increased in the positive direction by changing the
position of reversible switch to position ‘1’ and increasing the flow of current in the
solenoid. The curve follows the path of efa and the loop is completed. Again of is the
magnetizing force utilized to wipe off the residual magnetism oe.
 Hence, cf is the total coercive force required in one cycle of magnetization to wipe off
the residual magnetism. The loop abcdefa is called hysteresis loop.
29
Hysteresis Lose
 When a magnetizing force is applied, the magnetic material is magnetized and the
molecular magnets are lined up in a particular direction. However, when the
magnetizing force in a magnetic material is reversed, the internal friction of the
molecular magnets opposes the reversal of magnetism, resulting in hysteresis. To
overcome this internal friction of the molecular magnets (or to wipe off the residual
magnetism), a part of the magnetizing force is used.

 The work done by the magnetizing force against this internal friction of molecular
magnets produces heat. This energy, which is wasted in the form of heat due to
hysteresis, is called hysteresis loss.

30
Electromagnetic Induction
 It is a known fact that when an electric current flows through a conductor, a magnetic
field is immediately developed in the space surrounding the conductor.

 The phenomenon by which an emf is induced in a circuit when magnetic flux linking
with it changes is called electro-magnetic induction.

31
Michael Faraday’s Laws of Electromagnetic Induction
 First Law: This law states that “Whenever a conductor cuts across the magnetic field, an
emf is induced in the conductor.”

 A figure below shows a conductor placed in the magnetic field of a permanent magnet
to which a galvanometer is connected. Whenever, the conductor is moved upward or
downward i.e., across the field, there is deflection in the galvanometer needle which
indicates that an emf is induced in the conductor. If the conductor is moved along
(parallel) the field, there is no deflection in the needle which indicates that no emf is
induced in the conductor.

32
Michael Faraday’s Laws of Electromagnetic Induction
 Second Law: This law states that “The magnitude of induced emf in a coil is directly
proportional to the rate of change of flux linkages.”

 Induced emf,


 Usually, a minus sign is given to the right-hand side expression which indicates that emf
is induced in such a direction which opposes the cause (i.e., change in flux) that
produces it (according to Lenz’s law).

𝑁𝑑 ∅
𝑒=−
𝑑𝑡
33
Dynamically Induced emf
 By either moving the conductor keeping the magnetic field system stationary or moving
the field system keeping the conductor stationary so that flux is cut by the conductor,
the emf thus induced in the conductor is called dynamically induced emf.

 Considering a conductor of length l meter placed in the magnetic field of flux density B
Wb/m2 is moving at right angle to the field at a velocity v m/s as shown in Fig. (a). Let
the conductor be moved through a small distance dx meter in time dt second as shown
in Fig. (b).

34
Dynamically Induced emf

 Area swept by the conductor,

 Flux cut by the conductor,
 According to Faraday’s Law of electro-magnetic induction;
𝑑∅ 𝐵𝑙𝑑𝑥
𝑒=− =− =𝐵𝑙𝑣
𝑑𝑡 𝑑𝑡
35
Dynamically Induced emf
 Now, if the conductor is moved at an angle with the direction of magnetic field at a
velocity m/s as shown in Fig. (d) above. A small distance covered by the conductor in
that direction is dx in time dt second. Then the component of distance perpendicular to
the magnetic field, which produces emf, is .
 Area swept by the conductor,
 Flux cut by the conductor,
 According to Faraday’s Law of electro-magnetic induction;

𝑑∅ 𝐵𝑙𝑑𝑥𝑠𝑖𝑛 𝜃
𝑒=− =− = 𝐵𝑙𝑣𝑠𝑖𝑛𝜃
𝑑𝑡 𝑑𝑡

36
 !! !
You
k  
han
T
37