Presentation 1

Unit IV
Microprocessor
Introduction to Microprocessor
• A microprocessor is a controlling unit of a micro-computer, fabricated
on a small chip capable of performing Arithmetic Logical Unit (ALU)
operations and communicating with the other devices connected to it.
• Microprocessor consists of
• An ALU,
• Register array,
• Control unit.
ALU performs arithmetical and logical operations on the data received from the
memory or an input device. Register array consists of registers identified by
letters like B, C, D, E, H, L and accumulator. The control unit controls the flow
of data and instructions within the computer.
Block Diagram of a Basic Microcomputer

How does a Microprocessor Work?
• The microprocessor follows a sequence:
Fetch
Decode
Execute.
• Initially, the instructions are stored in the memory in a sequential
order. The microprocessor fetches those instructions from the memory,
then decodes it and executes those instructions till STOP instruction is
reached. Later, it sends the result in binary to the output port. Between
these processes, the register stores the temporarily data and ALU
performs the computing functions.
List of Terms Used in a Microprocessor
Here is a list of some of the frequently used terms in a microprocessor −
• Instruction Set − It is the set of instructions that the microprocessor can
understand.
• Bandwidth − It is the number of bits processed in a single instruction.
• Clock Speed − It determines the number of operations per second the processor
can perform. It is expressed in megahertz (MHz) or gigahertz (GHz).It is also
known as Clock Rate.
• Word Length − It depends upon the width of internal data bus, registers, ALU,
etc. An 8-bit microprocessor can process 8-bit data at a time. The word length
ranges from 4 bits to 64 bits depending upon the type of the microcomputer.
• Data Types − The microprocessor has multiple data type formats like binary,
BCD, ASCII, signed and unsigned numbers.
Features of a Microprocessor
Here is a list of some of the most prominent features of any microprocessor −
• Cost-effective − The microprocessor chips are available at low prices and
results its low cost.
• Size − The microprocessor is of small size chip, hence is portable.
• Low Power Consumption − Microprocessors are manufactured by using
metaloxide semiconductor technology, which has low power consumption.
• Versatility − The microprocessors are versatile as we can use the same chip in
a number of applications by configuring the software program.
• Reliability − The failure rate of an IC in microprocessors is very low, hence it
is reliable.
Introduction to Microcontroller
• A microcontroller is a small and low-cost microcomputer, which is
designed to perform the specific tasks of embedded systems like
displaying microwave’s information, receiving remote signals, etc.
• The general microcontroller consists of the processor, the memory
(RAM, ROM, EPROM), Serial ports, peripherals (timers, counters),
etc.
Difference between Microprocessor and Microcontroller
Microcontroller Microprocessor
Microcontrollers are used to execute a Microprocessors are used for big
single task within an application. applications.
Its designing and hardware cost is low. Its designing and hardware cost is high.
Easy to replace. Not so easy to replace.
It is built with CMOS technology, which Its power consumption is high because it
requires less power to operate. has to control the entire system.
It consists of CPU, RAM, ROM, I/O It doesn’t consist of RAM, ROM, I/O
ports. ports. It uses its pins to interface to
peripheral devices.
Microprocessor 8085
• 8085 is pronounced as "eighty-eighty-five" microprocessor. It is an 8-
bit microprocessor designed by Intel in 1977 using NMOS technology.
• It has the following configuration −
• 8-bit data bus
• 16-bit address bus, which can address upto 64KB
• A 16-bit program counter
• A 16-bit stack pointer
• Six 8-bit registers arranged in pairs: BC, DE, HL
• Requires +5V supply to operate at 3.2 MHZ single phase clock
• It is used in washing machines, microwave ovens, mobile phones, etc.
Internal Architecture of 8085
• Accumulator
• It is an 8-bit register used to perform arithmetic, logical, I/O & LOAD/STORE operations. It is
connected to internal data bus & ALU.
• Arithmetic and logic unit

• As the name suggests, it performs arithmetic and logical operations like Addition, Subtraction, AND,
OR, etc. on 8-bit data.
• General purpose register

• There are 6 general purpose registers in 8085 processor, i.e. B, C, D, E, H & L. Each register can
hold 8-bit data.
• These registers can work in pair to hold 16-bit data and their pairing combination is like B-C, D-E &
H-L.
• Program counter
• It is a 16-bit register used to store the memory address location of the next instruction to be executed.
Microprocessor increments the program whenever an instruction is being executed, so that the
program counter points to the memory address of the next instruction that is going to be executed.
• Stack pointer
• It is also a 16-bit register works like stack, which is always incremented/decremented by 2 during
push & pop operations.
• Temporary register
• It is an 8-bit register, which holds the temporary data of arithmetic and logical operations.
• Flag register
• It is an 8-bit register having five 1-bit flip-flops, which holds either 0 or 1 depending upon the
result stored in the accumulator.
• These are the set of 5 flip-flops −
• Sign (S)
• Zero (Z)
• Auxiliary Carry (AC)
• Parity (P)
• Carry (C)
• Its bit position is shown in the following table −
D7 D6 D5 D4 D3 D2 D1 D0
S Z AC P CY
• Instruction register and decoder
• It is an 8-bit register. When an instruction is fetched from memory then it is stored in
the Instruction register. Instruction decoder decodes the information present in the
Instruction register.
• Timing and control unit

• It provides timing and control signal to the microprocessor to perform operations.
Following are the timing and control signals, which control external and internal
circuits −
• Control Signals: READY, RD’, WR’, ALE
• Status Signals: S0, S1, IO/M’
• DMA Signals: HOLD, HLDA
• RESET Signals: RESET IN, RESET OUT
• Interrupt control
• As the name suggests it controls the interrupts during a process. When a
microprocessor is executing a main program and whenever an interrupt
occurs, the microprocessor shifts the control from the main program to process
the incoming request. After the request is completed, the control goes back to
the main program.
• There are 5 interrupt signals in 8085 microprocessor: INTR, RST 7.5, RST
6.5, RST 5.5, TRAP.
• Serial Input/output control

• It controls the serial data communication by using these two instructions: SID
(Serial input data) and SOD (Serial output data).
• Address buffer and address-data buffer
• The content stored in the stack pointer and program counter is loaded into the
address buffer and address-data buffer to communicate with the CPU. The
memory and I/O chips are connected to these buses; the CPU can exchange
the desired data with the memory and I/O chips.
• Address bus and data bus
• Data bus carries the data to be stored. It is bidirectional, whereas address bus
carries the location to where it should be stored and it is unidirectional. It is
used to transfer the data & Address I/O devices.

Presentation 1

Uploaded by

Copyright:

Available Formats

Presentation 1

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Presentation 1

Uploaded by

Copyright:

Available Formats

Unit IV

• Arithmetic and logic unit

• General purpose register

• Timing and control unit

• Serial Input/output control

You might also like