Digital Transmission

4-1 DIGITAL-TO-DIGITAL
CONVERSION
In this section, we see how we can represent
digital data by using digital signals. The conversion
involves
three techniques: line coding, block and
coding, scrambling.Line coding is always
coding needed;
and scrambling may or may not be needed.block

Topics discussed in this section:

 Line Coding
 Line Coding Schemes
 Block Coding
 Scrambling
Line Coding

 Converting a string of 1‟s and 0‟s

(digital data) into a sequence of signals
that denote the 1‟s and 0‟s.
 For example a high voltage level (+V)
could represent a “1” and a low voltage
level (0 or -V) could represent a “0”.
Figure 4.1 Line coding and
decoding
Mapping Data symbols onto
Signal levels
 A data symbol (or element) can consist of a
number of data bits:
 1 , 0 or
 11, 10, 01, ……
 A data symbol can be coded into a single
signal element or multiple signal elements
Relationship between data
rate and signal rate
 The data rate defines the number of bits sent
per sec - bps. It is often referred to the bit
rate.
 The signal rate is the number of signal
elements sent in a second and is measured in
bauds. It is also referred to as the
modulation rate.
 Goal is to increase the data rate whilst
reducing the baud rate.
Figure 4.2 Signal element versus data
element
Data rate and Baud rate

 The baud or signal rate can be

expressed as:
S = c x N x 1/r bauds
where N is data rate
c is the case factor (worst,
best & avg.)
r is the ratio between data
element &
signal element
 Example 4.1

A signal is carrying data in which one data element is

encoded as one signal element ( r = 1). If the bit rate is
100 kbps, what is the average value of the baud rate if c is
between 0 and 1?

Solution
We assume that the average value of c is
1/2 . The baud rate is then
Considerations for choosing a good
signal element referred to as line
encoding
Line encoding C/Cs

DC(Data Current) Component:- the

average amplitude of a unipolar encoded
signal in nonzero. This creates what is
called DC(direct signal component) a
component with nonzero frequency.
Line encoding C/Cs

Self synchronization – When a signal is

unvarying, the receiver cannot
determine the beginning and ending of
each bit.
Figure 4.3 Effect of lack of
synchronization
 Example 4.3

In a digital transmission, the receiver clock is 0.1 percent

faster than the sender clock. How many extra bits per
second does the receiver receive if the data rate is
1 kbps? How many if the data rate is 1 Mbps?
Solution
At 1 kbps, the receiver receives 1001
bps instead of 1000 bps.

At 1 Mbps, the receiver receives 1,001,000 bps instead of

1,000,000 bps.
Line encoding C/Cs

 Error detection - errors occur during

transmission due to line impairments.
 Some codes are constructed such that
when an error occurs it can be
detected. For example: a particular
signal transition is not part of the code.
When it occurs, the receiver will know
that a symbol error has occurred.
Line encoding C/Cs

 Noise and interference - there are line

encoding techniques that make the
transmitted signal “immune” to noise
and interference.
 This means that the signal cannot be
corrupted, it is stronger than error
detection.
Line encoding C/Cs

 Complexity - the more robust and

resilient the code, the more complex it
is to implement and the price is often
more than simple one.
Figure 4.4 Line coding
schemes
Unipolar
 All signal levels are on one side of the time
axis - either above or below
 NRZ - Non Return to Zero scheme is an
example of this code. The signal level does
not return to zero during a symbol
transmission.
 Scheme is prone to DC components. It has no
synchronization or any error detection. It is
simple but costly in power consumption.
Polar - NRZ
 The voltages are on both sides of the time
axis.
 Polar NRZ scheme can be implemented with
two voltages. E.g. +V for 1 and -V for 0.
 There are two versions:
 NZR - Level (NRZ-L) - positive voltage for one
symbol and negative for the other
 NRZ - Inversion (NRZ-I) - the change or lack of
change in polarity determines the value of a
symbol. E.g. a “1” symbol inverts the polarity a “0”
does not.
Figure 4.6 Polar NRZ-L and NRZ-I
schemes
Note

In NRZ-L the level of the

voltage determines the value of
the bit.
In NRZ-I the inversion
or the lack of inversion
determines the value of the
bit.
Note

NRZ-L and NRZ-I both have an

average signal rate of N/2
Bd.
Note

NRZ-L and NRZ-I both have a DC

component problem, it is worse for NRZ-
L. Both have no self synchronization
&no error detection. Both are relatively
simple to implement.
Polar - RZ
 The Return to Zero (RZ) scheme uses three
voltage values. +, 0, -.
 Each symbol has a transition in the middle.
Either from high to zero or from low to zero.
 This scheme has more signal transitions (two
per symbol) and therefore requires a wider
bandwidth.
 No DC components or baseline wandering.
 Self synchronization - transition indicates
symbol value.
 More complex as it uses three voltage level.
It has no error detection capability.
Figure 4.7 Polar RZ
scheme
Polar - Biphase: Manchester and
Differential Manchester
 Manchester coding consists of combining the
NRZ-L and RZ schemes.
 Every symbol has a level transition in the middle:
from high to low or low to high. Uses only two
voltage levels. (example Ethernet LAN)
 Differential Manchester coding consists of
combining the NRZ-I and RZ schemes.
 Every symbol has a level transition in the middle.
But the level at the beginning of the symbol is
determined by the symbol value. One symbol
causes a level change the other does not.
(example Token Ring LAN)
Figure 4.8 Polar biphase: Manchester and differential Manchester
schemes
Note

In Manchester and differential

Manchester encoding, the transition
at the middle of the bit is used for
synchronization.
Note

The minimum bandwidth of Manchester

and differential Manchester is 2 times
that of NRZ. The is no DC component.
None of these codes has error detection.